AMRUT 2.0-Improvements of Water Supply Scheme to Melachokkanathapuram Town Panchayat, Theni District under AMRUT 2.0 Scheme

Amount

Eartwork Excavation

1. Earthwork excavating and depositing on bank with an initial lead of 10m & initial lift of 2m in sand silt other loose soil, wet sand or silt not water,Light black cotton soil, sandy loam, hard stiff clay, stiff black cotton, hard red earth shales, muram, graverl stoney earth & earth mixed with small size boulders & hard gravelly soil as per S.S 20B

Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in Soft disintegrated rock, Laterite, Soft rock or Kankar, not requiring blasting etc., as per SS 20 A. TNDSS NO: 23 & 24 VI (S2) VI,VII 9,10 wit

Labour for cutting open road for laying water mains or sewer

i) B.T. Roads (or) Maccadam road - Road length given by TP

ii) Concrete Roads - Road length given by TP

Labour for cutting open road for laying water mains or sewer

Ordinary Soil - such as Hard stiff clay, stiff black cotton, hard red earth, shales, murram gravel, stoney earth and earth mixed with small boulders and hard gravelly soil etc.,

110 mm HDPE PN 10

180 mm HDPE PN 10

200 mm DI K7

250 mm DI K7

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

Sinking well below water level including all incidental charges using special tools and plants such as air compressor, helmet etc., complete and including baling out water.

First depth of 2m

Plain Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Plain Cement Concrete 1:2:4 Mix (one part cement, two part sand and four part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour

Porous Concrete 1:2 mix using 20mm ISS HBG Metal

9. Provding and laying in position, Standardised concrete Mix M-25 Grade in accordance with IS 456-2000, using 20mm and down graded hard broken granite water cement ratio of 0.50, including admixture (plasticiser/ super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg of sand, but excluding cost of reinforcement grill and fabricatingcharges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, during, etc. complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements os IS Standards (No separate payment will be made by the Department for the excess usage of materials).

1.5 m to 4.5 m below G.L

0m to 1.50m below G.L

0 to 4.5m above GL

4.50 to 7.32m above GL

7.32 to 10.98 m above GL

10.98 to 14.64 m above GL

Providing and laying in position Standardised concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ration of 0.45, including admixture (plasticiser/ super plasticiser) in recommended proportins as per IS:9103 to acceierate, retard setting of concrete, improve workanility without impairing strength and durability with about (5.0cu.m) 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum ) 5156kg of 10-12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670kg of sent, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering fixtures lide fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate Payment will be made by the Department for the excess usage of materials)

1.5 m to 4.5 m below G.L

Below GL

0 to 4.5m above GL

14.64m to 18.3 m above GL

18.3 to 21.96 m above GL

Centering for sides and soffits of R.C.C slab of plane surface for R.C.C floor slab including strutting upto 3.3 mt height using MS sheets of size 90cmx60cm and stiffend with welded MS angle of size 25mmx25mmx3mm laid over silver oak (country wood) joist

Plane Surface

3.30 - 4.30M above GL

7.30 - 8.30M above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

15.30 - 16.30M above GL

Square Column

3.30 - 4.30M above GL

4.30 - 5.30M above GL

5.30 - 6.30M above GL

6.30 - 7.30M above GL

7.30 - 8.30M above GL

8.30 - 9.30M above GL

9.30 - 10.30M above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

12.30 - 13.30M above GL

13.30 - 14.30M above GL

14.30 - 15.30M above GL

15.30 - 16.30M above GL

Curved Surface

14.3 - 15.3 M above GL

15.3 - 16.3 M above GL

Circular Column

3.30 - 4.30M above GL

4.30 - 5.30M above GL

5.30 - 6.30M above GL

6.30 - 7.30M above GL

7.30 - 8.30M above GL

8.30 - 9.30M above GL

9.30 - 10.30M above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

12.30 - 13.30M above GL

13.30 - 14.30M above GL

14.30 - 15.30M above GL

15.30 - 16.30M above GL

Brick Work in Cement Mortar 1:5 Mix (one cement, five sand) using new best II Class Ground Mould chamber Bricks of size ( 9” x 4 3/8” x 23/4 “ )from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Plastering with CM 1:5(one cement and three sand) 20mm thick including cost of materials, labour charges for finishing, curing etc., complete and as directed by Departmental Officers

Plastering with CM 1:3(one cement and three sand) 10mm thick including cost of materials, labour charges for finishing, curing etc., complete and as directed by Departmental Officers

B) Finishing the top of roof with one course of machine pressed tiles 23 C.m x 23 C.m x 2 C.m size using cement mortor 1:3 mix mixed with 2% by weight of Crude Oil and pointing with Cement Mortor 1:3 mix Cost of all materials and labour charges and brick

Exterior Emulsion paint Two coats with good quality of approved Emulsion paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc., Complete as per Standard Specifications for 10 sqm

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2.

Supplying fabricating and placing in position of RTS road at all heights for reinforcement including cost of steel for all works and labour charges including cost of binding wire etc., complete for all RCC works and as directed by Departmental Officers

Supply and fixing of M.S Grill Gate with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supply and fixing of Rolling shutter of Size 2.5m *2.5m Manually operated with necessary appliances and as directed by Departmental Officers

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Supply and Fixing of Steel galzed ventilators of the N type of Size 0.45 m x 0.60 m fabricated with 35*20*4.0m Ms Flats wherever necessary includings all fixtures and appliances as per Standard Specification and as directed by departmental officers

Supplying and fixing in position C.I. Manhole covers (light or heavy duty) of 600mm X 600mm sizes of best approved quality and as per standard specifications etc., complete.

Provision for CI Steps to be placed in Staggered manner including fixing etc complete and as directed by departemental officers

2T capacity hand operated over head Travelling (HOT) crane suitable for a span upto 6 Mtrs, and travel length upto 10 Mtrs. with clear lift upto 6 Mtrs. including gear type chain pulley block with GI chain and geared Travelling trolley complete with all accessories including girder

Provision for Shell with lock and Key arrangements to Keep the log Book Tools etc and as directed by Departmental officers

Supply and fixing in position of R.C.C.(1:1.5:3) pre-cast ladder of length 4m with vertical post of size 0.1 x 0.15m and step size of 25x25mm with 45cm width for inside the tank using hard broken stone jelly and river sand including the cost of reinforcement grills and fabrication charges moulding, curing, finishing charges and fixing in position neatly complying with standard specification and as directed by the Departmental Engineer etc. complete

Providing cut stone set in CM 1:3 (one cement and three sand) using well dressed cut stone supporting inlet pipe of size 0.30 x 0.30 x 0.15m for service reservoir etc., complete as per standard specifications and as directed by Engineer-in-charge.TWAD SOR

AC Cylindrical Cowl-100 mm

Supply, delivery and fixing in position of water level indicator with float of approved pattern for inner and outer compartments including cost of materials etc. and as directed by the Dept. officers.

Forming Ring bund using sand bags filled with filling sand stiching the bags with jute coir conveing the stiched sand bags to preached site and forming the ring bund by placing the stiched sand bags in proper position , packing tightly and blocking the joints with clay and straw leaves to arrest the leakage as stated by departmental officers including the cost of empty cement bags, sand, jute coir complete for 2.83 cum.

Barricading work (Where the lines are in narrow width of municipality area,busy streets like Market, Bus-stand and in the Highways etc.) for laying ofpipe line using casurina poles at 1.50m center to center (8cm to 10cm dia.and 1.80m height) vertical with horizontal poles in two rows, painting thevertical poles in the road facing sides with ready mix paint, tying the vertical and horizontal poles with coir rope including supplying, delivery and fixing of GI sheet (0.90m x 0.8mm thick) in the horizontal poles and fixing75mm dia. reflectors including earth work excavation for fixing verticalposts and finally removing and stacking the materials safely for further useetc., complete and as directed by TWAD Board officers.

Traffic

Non Traffic

Lowering DI Pipes

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the TWAD Officers.

200 mm DI K7

250 mm DI K7

Lowering HDPE Pipes

Lowering the following pipes and specials into trench and laying to proper grade and alignment complete as per standard specifications and as directed by the Departmental Engineer.

110 mm HDPE PN 10

180 mm HDPE PN 10

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

Jointing Di pipes

Jointing the C.I/ D.I-S/S pipes and specials with neat cement or cement mortar and spun yarn including caulking the joints, curing. (including cost of jointing material

200 mm DI K7

250 mm DI K7

Jointing HDPE Pipes

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc.

110 mm HDPE PN 10

180 mm HDPE PN 10

90 mm diameter (50.0m length for 1 Nos of Joints )

110 mm diameter (6.0m length for 1 Nos of Joints )

140 mm diameter (6.0m length for 1 Nos of Joints )

160 mm diameter (6.0m length for 1 Nos of Joints )

180 mm diameter (6.0m length for 1 Nos of Joints )

200 mm diameter (6.0m length for 1 Nos of Joints )

250 mm diameter (6.0m length for 1 Nos of Joints )

Testing pipes

Testing of D.I/HDPE pipes for water supply with hydraulic testing equipment by filling with water (including cost of water @ Rs. 60/KL) and testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc., complete for the following diametres of pipes.

110 mm HDPE PN 10

180 mm HDPE PN 10

200 mm DI K7

250 mm DI K7

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

Refilling or backfilling trenches with excavated soil after pipe laying in layers not exceeding 20 cm in depth, ramming and consolidation of each layer, watering etc. all complete as per standard specifications and as directed by the Departmental Engineer.

110 mm HDPE PN 10

180 mm HDPE PN 10

200 mm DI K7

250 mm DI K7

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

Construction of Brick work valve Chamber with M20 Grade concrete . The rate should include earth work excavation in various soils met with at the site of work, refilling the pit after the construction of the pit, PCC M10 for Blinding Concrete, Brick work in CM 1:5 and plastering with CM 1:5 - 12mm thick, cost of steel reinforcement fabrication charges, Cover slab with manhole cover etc., and fixing the valves in position inside the pit including laying, jointing of valves, HDPE pipes and specials including the cost of jointing materials such as bolts and nuts RI sheets washers etc., complete and as directed by the Departmental Engineer.

Construction of RCC spiral staircase in RCC M25 (one cement, one and half sand, three aggregates) using 20mm HBGS of 1.80m diameter of required height for approach to the roof of service Reservoir with RCC handrails including earthwork excavation, providing CC 1:4:8 mix, RCC footing 1:1.5:3 mix, GL platform etc., and also including cost of steel reinforcement, fabrication charges, scaffolding, centering, precasting charges, cement, painting etc. complete as per standard specifications and as directed by Engineer, The staircase shall be braced to the column of service reservoir at suitable interval. (in the BOQ, quantity column the exact height to be mentioned from GL to roof slab bottom to get total value of work to be done.

DI Pipes

Supplying of K9 DI Pipe of dia following dia, conforming to IS 8329-2000 including all local and central taxes , transportation, freight charges, loading and unloading, conveyance to site and stacking the same, cost of all labour, material & etc complete.

200 mm DI K7

250 mm DI K7

infilltration well 100 mm DI K7

HDPE Pipes

Supplying of HDPE pipe of PE 100 grade, PN -6 class conforming to IS 4984 including all local and central taxes , transportation, freight charges, loading and unloading, conveyance to site and stacking the same, cost of all labour, material & etc complete

110 mm HDPE PN 10

180 mm HDPE PN 10

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

DI Specials

Supply & Delivery to site of all types of specials such as Tees, Tapers. Bends, endcaps etc as per specification.

HDPE Specials

Supply & Delivery to site of all types of specials such as Tees, Tapers. Bends, endcaps etc as per specification.

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

DI Valves

Supply and delivery of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron ofGrade GGG 40 or equivalent grade,Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 ORing protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 4846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application withpressure rating PN 10/16

100 mm DI Sluice Valve

150 mm DI Sluice Valve

200 mm DI Sluice Valve

250 mm DI Sluice Valve

100 mm DI Scour Valve

100 mm DI NRV

250 Mm NRV

50 mm Air valve

150 mm Flow Control Valve

Orifice 100 mm

Flow Meter

Electromagnetic Flow Meter shall be a velocity sensing Electromagnetic type, microprocessor based signal converter, sealed housing, flanged tube meter for 1.0 Mpa working pressure, manufactured to highest standard available for mag-meters, equipped with minimum six digit digital totalizers, reading in different units (Kiloliters / Cubic meter) and shall be accurate within 0.5% of Measured value, shall operate within a range of 0.3 m/sec to 4 m/sec and be constructed as follows: Meter tube (Sensor) shall be fabricated from stainless steel tube and use class PN10 flat face carbon steel flanges in accordance with IS 1538. These flanges shall be welded to the flow tube. The internal and external of the meter tube shall be blasted to near white and lined with hard rubber/ Polyurethrene/ PTFE preferably by SBR or EPDM. Meter tube shall have a constant nominal inside diameter offering no obstruction to the flow. The accuracy should be inclusive of linearity, hysteresis, repeatability, temperature and pressure effects. Coil Housing shall be fabricated from stainless steel (SS304)/ Die cast Aluminium/ Carbon steel with anticorriosive paint for corrosion resistance and welded to the tube providing a completely sealed environment for all coils, electrode connections and wiring harness capable of submerged or buried operation with IP68 Protection. Signal Converter shall be pulsed DC coil excitation type with auto zeroing. The signal converter shall be remotely mounted away from the meter. The converter shall indicate direction of flow and provide a flow rate indication and a total of flow volume for both forward and reverse directions. The converter shall provide an isolated 4-20 mA output into minimum 500-ohm load and a frequency output of a maximum of 0-10 KHZ and a scaled pulse output. The microprocessor based signal converter shall have a self-diagnostic test mode and a backlit display that continuously displays “Rate of Flow” and “Total Volume”. Converter shall be supplied with a programmable low flow drop out, higher flow and empty pipe zero return. The signal converter housing should be die-cast aluminum with glass window. The converter cum transmitter should be fully programmable from the front facia. The programming should be user friendly, self-prompting menu driven. Flow meter test calibration certificate from FCRI, flow test lab / NABL accredited lab to be furnished.

OHT Pipe Connection

Supply and delivery of 150mm dia C.I D/F Pipe The rate shall inclusive of all charges such as materials and loading, unloading, transportation charges and all taxes etc, complete as per standard specification.

150 mm CI Pipe

250 mm CI Pipe

ELECTRICAL WORKS

Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Duty 500 lpm and 25 m head - 10 HP

Horizontal Split Casting Centrifugal pump

Supply and delivery of Horizontal split casing centrifugal pump conforming to IS 1520 and as amended thereafter with CI casing andsplit glands, stainless steel shaft, hydraulically and dynamically balanced bronze impellers capable of discharging required quantity of water against a total head noted below due to all causes and with the accessories such as G.M air release cock, Grease cup, G.I priming funnel, M.S lifting hook, drip water G.I pipe connections, leading to the outside of pump house rubber water deflector, doubleflap foot valve, G.M strainer including unique tyre type coupling, common M.S fabricated base to mount pump and motor and other standard fittings etc complete. Pump shall be capable of discharging the specified quantity at the head noted at the minimum NPSH at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase, 415 V, 50 Hz, 1500 RPM.

Duty 2500 lpm and 60 m head

Duty 1500 lpm and 90 m head

Control Panel

Pump Well 1

Supply and delivery of suitable KW indoor automatic air cooled dust and vermin proof FLEX COMPENSATED MAGNETIC AMPLIFIER Soft Starter for the operation in 3.3 KV three Phase 50 HZ, AC supply termination with phase segregated neutral terminal box of the motor , housed in 14 SWG sheet steel enclosure, painted with epoxy or polyurethene , 230V AC 10 Amps control supply , Class B insulation, 300 mm height fabricated pedastal (to prevent water ingress for starter panel) and condensation heater with switch with thermostat, interlocking with running motor with built in facility for run mode/by pass etc. complete. The starter may be provided with contactors suitable for next standard higher KW rating, Over load relay, instrument panel with frequency meter, Ammeter, Voltmeter, indicating lamp 6 Nos, LED ON/OFF type and Start /Stop push button. SUITABLE FOR H.T. SQUIRREL CAGE MOTOR

FCMA SOFT STARTER-38 HP

Submerible Pump Set

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Labour charges

Horizontal Split Casting Centrifugal pump

Labour Charges for erection of Horizontal shaft, centrifugal pumpset (Coupled/Monoblock) in bore well/Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventor and laying and jointing the cables and twin earthing as per IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by EB authorities.

above 30 HP to 40 HP

Providing TWIN Earthing to all starters

upto 25 HP

Above 25 upto 60 HP

Cable: supply and fixing of 4 sq mm PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 AND AS AMENDED THEREAFTER .

Supply and delivery of brand new approved make 1.1 KV grade armoured aluminium conductor cable confirming to ISS 1554 part I with ISI marking including loading, freight, transit insurance, incidental charges, packing, taxes and unloading, stacking at site in good condition including excise duty etc., complete as directed by the TWAD Board officers.

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

Laying of 1.1 KV class UG cable in trench / GI pipe / on pole as required.and as directed by Engineer incharge.

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

JOINTING OF L.T.CABLES 3,3.5,4CORE 1.1KV GRADE ARMOURED ALUMINIUM CONDUCTOR CABLE CONFIRMING TO IS1554 AND AS AMENDED THERE AFTER PARTI WITH ISI MARKING

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

Supply and delivery of 150mm dia Bourden tube type pressure gauge (glycerin filled)with concentric scale suitable for pumpsets in item I duly mounted on a teak wood Board to be fixed on well of the pump house with required copper tube connection with brase stop cock etc. The gauge should conform to relevant I.S. 3624

Electrical gloves tested to 11 KV / 22 KV with wooden box dusted with french chalk powder

Electrical gloves tested to 11 KV / 22 KV with wooden box dusted with french chalk powder

Supply and fixing of Electrical quality 6mm thick rubber mat

Supply and fixing of 5 Kg capacity ISI marked Dry chemical powder fire extinguisher

Supply and fixing of fire bucket - 3 Nos. hooked to MS stand

Supply and fixing of laminated shock treatment chart

Supply and fixing of wooden first aid box

Supply and fixing of Rechargeable Emergency lamp (600mm Fluoracent lamp)

Supply and Delivery of Tools required for Pumproom

Provision for DI Pipe connection

300 mm DI PN10 Flanged pipes (2m length pipes)

Electro Magnetic Flow Meter-300 mm

HSC Connection - 20 mm - Providing House service connection with MDPE 20mm pipe (supply, lowering, jointing & testing), electrofusion tapping saddle PE 80 blue, PN 12.5 with female threaded metal insert of SS 304, Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded to suit the corresponding bore sizes of 15mm dia size ( 1/2", ), Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 , Poly propylene 90 Degree Compression elbow with compression joint at both ends, Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 and protection box of size 20cm x 30cm for fixing of Water Meter all as per standard including road cutting, replacement of utilities providing house service connection, refilling, retoration of roads/drains testing etc complete with materials and specification as instructed by department officers.