Construction of New Library at MKB Nagar Chennai

Amount

Removing the existing ventilators,doors and windows including removal of frames, hinges and fastenings carefully and stacking the same at site etc., complete

Dismantling the existing brick or stone masonry work in cement mortar under 3m high including carefully clearing the debris etc.,complete.

Dismantling RCC by manual / by using deploying machineries carefully clearing away the debris as directed during execution. The dismantling of concrete as per PWD schedule of rates are to be adopted wherein a part part of the concrete only is to be dismantled and the remaining part of the concrete has to be retained structurally safe.

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete SS.20B

Narrow Foundations for building & culvert- First Depth Upto 2m

Narrow Foundations - Second Depth 2m - 3m

Providing and constructing cast in situ hydraulic bored piles of 375mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc ., Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Providing and constructing cast in situ hydraulic bored piles of 450mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc ., Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and filling of Gravel / Good Earth by lorry in Foundation basement filling and site filling with approved materials excavation from approved quarries and compacted to meet requirement of table 300-1, 300-2 of MORTH, in layers not exceeding 250 mm loose thickness, spreading, breaking clods, removal of roots and other organic materials to the required line, grade and cross-section including watering, spreading by Dozer, grading by motor grader and consolidation by vibratory road roller with desired field density not less than 95% of maximum dry density ,including all lead,lift, loading, unloading, all labour, hire charges of all machineries, Transportation, etc., complete in accordance with MORTH technical specification clause No. 305 and with all other incidental charges and as per the direction of the Engineer-In-Charge.

Construction of Wet Mix Macadam 250mm compacted thickness in two layers by providing , laying , Paving , and compacting of aggregate gradation satisfying to Table 400-13 of MORTH and satisfying the physical paraeteres as per MORTH Table 400-12, mixing in a Wet Mix Plant of 200 tonne capacity at OMC , carriage of mied material to work site and laid in sensor pavers to the required line and grade as per the drawing and compacted with vibratory roller of 8-10 tonne to achieve the desired density of 98% of Maximum dry density and as per the direction of the Engineer-In-Charge of work.

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide “Chloripyrifos” and spraying the same termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II) / 1981 and as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc.,Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

Reinforced cement concrete Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

For plane surfaces such as recangular or square columns, sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. Rate to include all leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer in charge

For Foundation & Basement

Ground floor

First floor

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers -

For Foundation & Basement

For Ground floor

First floor

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required.Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing Fly ash Brick masonry in Cement Mortar 1:5 (One cement and Five M sand) in foundations, basement and superstructure using Fly ash Bricks of size 230x110x75mm etc. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

For foundation & basement

For Ground floor

First floor

Terrace floor

Supply and constructing Flyash Brick partition wall 115mm thick in Cement Mortar 1:3 (one cement and three M sand) 11.50 CM thick using using Fly ash Bricks of size 230x110x75mm including both side plastering with CM 1:5 12mm thick and using hoop iron reinforcement if found necessary and hoop iron shall be supplied to the department at free of cost etc., complete as directed by the Engineer in- charge.

For Ground floor

For First floor

Special ceiling plastering and finishing all RCC exposed surfaces such as RCC slabs, sunshades, canopies, stair case steps, landing slabs etc with CM 1:3 (One cement and three sand) 10mm thick including hacking the surfaces and providing necessary CM nosing, beading as per size specified wherever necessary using the same mix etc., complete complying with standard specification and as directed by the Departmental Officer.

Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications.

Waterproofing: Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the UGT/ OHT tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for 3 times a day for 5- 7 days. Followed by applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti algae, antifungal, Non-toxic, hygiene cum damp-proof coating Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA, having mixing Ratio (Base: Hardener: Water) – 1:1:1 to be applied @ 0.35 Kg/m2 in 2 coats. Ensure that this coating is applied over the protective plaster. The Waterproofing material shall have Specific Gravity: 1.2, Water vapor permeance: 244.48 g/m2/24 hrs, as per IS 7809/Pt 2/1977, Adhesion strength: 2 N/mm2 as per ASTM D 4541: 02. The finished cost to include surface preparation completely as per specification.

Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (1 Liquid: 2 Powder), to the RCC surface like bathroom, toilet, balcony & utility area applied @ 1.7kg/m2 in 2 coats to achieve 1mm DFT, having Elongation at break >50% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80 N/mm2 as per ASTM D 4541, crack bridging upto 1mm as per ASTM C 836, Water penetration (5 bar pressure) as per BS EN 12390. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

PVC mould CI Steps for Sump

Manufacturing, Fabrication, Supply and delivery of Aluminium ladder 6m height Folding type for operating inside the pumproom made out of Aluminium “ Џ “ channel 3” x 1 1/2” , 4mm thick for sides and steps in “L” channel 3” x 1 1/4” , 4mm thick @ 45cm width, 30cm c/c providing with suitable roller, rope, rubber bush etc. including cost of all materials, labour etc.

Painting the new plastered walls with two coats for Interior Plastic Emulsion paint approved quality and colour over a priming coat, with two coats of wall putty including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting the old plastered walls with two coats of Exterior emulsion paint (weather proof ) first class quality and of approved colour over a priming coat including thorough scrapping,clean removal of dirt,etc.,complete and including necessary plaster paris,putty etc., wherever required.as per (ISI STD) (It must provide excellent resistance against the growth of algae and fungi on the walls. And it must offer excellent protection against alkali and UV degradation and the durability period should be 5 years.

Providing Microcment Plaster with Following Specifications Microcement is prepared from a powder component (microcement base for the preparation of the works and microcement fine for the finish) and a liquid component. These two components must be mixed homogeneously according the following proportions: • Microcement Base (microcement base: preparation mortar) 10 kg of powder must be mixed with 3 liters of concentrated liquid • Microcement Fine (microcement fine: finishing mortar): the mix will be done as follows; for 10 kg of powder approximately 4.5 liters of liquid will be used The mortar must be prepared as follows: 1. Pour little amount of resin (component B) into a container, then add the quantity of pigment required according to the amount of microcement to be used, and then mix them up until a uniform colour is achieved. 2. Pour gradually the Microcement powder (component A). Add the powder as the product is mixed with a slow speed mixer drill. 3. Mix for at least 2 minutes until the mortar is smooth and free of lumps.

Painting the new Iorn work with two coats of Ready Mixed Enamel Paint of aproved quality and colour over the existing priming coat including the cost all materials etc.,complete, in all floors and as directed by the Departmntal Officers.

Fabricting Supplying and fixing in position aluminium anodised Natural color matt finish Arch door of size 1.80mx2.40m using 5.50mm thick Plain glass at top with aluminium grill 10mm thick double leaves dooors with suitable frames and necessary accessories such as rubber beading PVC felt, handle for a length of shutter (both sides), locking arrangements, Furniture fittings.

ABS DOOR / EQUIVALENT Specification: Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work. Design Pre-laminated Door

Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers

STEEL DOOR Fabricating Supply and fixing and position of MS doors with single leave. The door outer frame will be 40x40x6mm MS angle, the shutter frame will be 35x35x6 mm, MS angle intermediate stiffner will be 35x35x6 mm with cross stiffner 25x 25x5 mm flats covered with 18 gauge M.S. sheet with necessary hinges, tower bolts, aldrop length 30mm and hold fast etc., complete with one coat red oxide primer.

Supplying, Fitting, Fixing and Installation of Merino Besco TITAN 12MM BOX UP series cubicles (or approved equivalent make) of width and depth as per specifications/ site drawings.Cubicle height to be 2100 mm and/or as perrequirement/site conditions. Length & breadth of the cubicles shall be as per requirement and /or as per site conditions. ITEM-DESCRIPTION:- Made from solid grade compact high pressure laminate as per IS:2046 and EN 438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of Kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fibre impregnated withthermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along withanti-bacterial properties. Panels have a black corethat when machined, presents a distinctive black edge. Doors: All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed tothe pilasters. Stainless steel made coat hook and lockset are provided with each door. All the doors will be routered at the vertical ends and the rubber spongelining will be incorporated at the routered ends. Pilasters: All pilasters will be made of 12 mm thick Merino HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Pilasters will be anchored to the floor using steel made Lbrackets and box up fixtures are used for covering the floor anchored mechanism. All pilasters will be routered at their vertical ends to facilitate closure of doors. The bottom gap is 100 mm. Dividers: All intermediate partitions or dividers will be made of 12 mm thick Merino HPL compact laminate panels. They are affixed with stainless steel made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panelsto be as per drawing / as per requirement/ site conditions. HARDWARE & ACCESSORIES: • Top rail is made of stainless-steel grade 304. A thin plastic film pasted for surface protection.Dimension is 55mmx42mmx1.6mm-Tee. • Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8mm-Tee. • Wall joinery section with hamming profile made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Size to be 21mmx16mmx0.8mm-Tee. • Fixed front panel to be anchored to floor with L Bracket of SS and covered with SS 316 Grade Box Type plate from all directions with 100mm clear Height from ground. Surface finish to be matt-type. • Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacquer coated. • Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt-type. • Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt-type. • Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type. • Anti-noise rubber padding of thickness 2 mmand width 10 mm • Stainless steel grade 304 screws. Material: Merino Make or Approved Equivalent Mode of Measurement: - From finished floor to top of cubicles, as and where found the physical height of the finished structure . No wastageshall be considered for measurement purpose. Merino Make or Approved equivalent material

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Fabricting Supplying and fixing in position aluminium anodised Natural color matt finish window using 5.50mm thick Plain glass at top with aluminium grill 10mm thick double leaves dooors with suitable frames and necessary accessories such as rubber beading PVC felt, handle for a length of shutter (both sides), locking arrangements, Furniture fittings.

Providing and fixing Vertical blinds , quality of approved make fabric made of 100% polyester woven fabric thickness 0.40mm with virtually maintenance free having plastic bottom chain thickness of chain-0.50mm and diameter-3mm, Plastic with metal bottom and suitable coating on exterior, including all fixtures and fittings complete in all respect as per design/color/shade including requisite installation brackets etc as required for installation at site with anchoring arrangements complete.

Providing and laying Flagstone 600x600x65mm including all materials, labour etc., complete and as directed by the Departmental officers.

Providing and laying to required line and grade as per the drawing interlocking cement concrete Paver blocks of M 30 grade 63 mm thick laid over the sand cushion . The size and the shape of the concrete blocks had to be approved before sourcing / manufacturing the same. The gaps between the two blocks shal be filled with relatively finer sand than the bedding sand of gradation as per Table 2 . The paver blocks shall be compacted using a light tandem roller or plate compactor till the required grade and line is achieved. The rate shall include laying of the bedding sand levelling , laying of paver blocks , filling of the filling sand and compaction etc. complete and as directed by the Departmental officers.

Providing and laying of Black Granite Cobble Stone flooring of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Supplying and installing Woven vinyl tile 500 x500 Antibacterial with approval color as per the Code, Completed work including cutting, placing, using appropriate gluing material,...etc. which should making necessary opening for floor boxes whenever requested or directed by the Engineer, Different samples must be submitted for review and approval prior of starting the delivery and installation works.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 1200x2400x9mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Executive Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 600 mm x 600 mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying with best quality the following materials of Machine Polished granite slab of 18 mm thick (Fine Polished Steel Grey Granite Slab) including cutting and edge polishing to be set in CM 1:3 (1 of cement : 3 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Nosing for Granite Slab - Single Nosing

Nosing for Granite Slab - Double Nosing

Nosing for Granite Slab - Grooving the Granite slab

Finishing the top of roof with one course of Solar Reflective ceramic tiles of size 305 mm x 305 mm x 7 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Providing and laying Stonecrete flooring as per approved colour an patters

Providing and laying Stonecrete Dado as per approved colour an patters

Providing grooves for 25mm width 10mm Deep

SUPPLY AND INSYTALLATION OF EVERWOOD DECKING : Everwood composite EWD146x23D deck board fitted on hollow aluminium joist EWD50x30EDx1.5mm framework. Framework fitted on floor with intervals not exceeding 350mm c/c with aluminium L-clamp & Boss240 -adhesive solution as designed. Composite plank fitted on joist with SS304 grade start & end clips / PA grade center clips fastened with corroshield 7x25CSK screws. Necessary sides to be covered with EWD57X10 trims as specified and finished all complete

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/ltr and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane:

Art work as per the direction of department official, over Oil Painting with first class quality and approved colour including a priming coat with thorough scrapping clean removal of dirt., etc., complete and including necessary plaster of paris, putty, etc., wherever required (Relevent ISI STD), including putty works.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing two legged scaffolding using 15cm dia casuarinas post of 4.0 m over all length of (3 M Height+0.5 M over all length (3.0M height +0.5m projection +0.5m in to the ground ) the distance between the two rows being 1.25M and the spacing of posts being 2.0M in both the rows with two horizontal posts with 0.5M overlap on either side and braces at 2.0M centre to centre including longitudinal and traverse middle braces to step up and transverse middle braces to step up and providing a plat form with country wood planks of 40mm thick and 1 M width ,etc in a complete form using coil and nails (Rate for an initial height of 3.0M and length of 1 M)

Scaffolding charges for every additional height of 2.5 M height over the initial height of 3 m.

Supply and fixing Shade net (Green Net) for under construction of high rise building

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

Providing and Fixing of polyurethane foam for Sloped roof as thermal insulation panels or Sandwich insulated panels with external 0.50mm total coated thickness pre painted Galvalume sheet with trapezoidal roofing profile having crest height of 38mm at every 333mm span , whereas internal 0.50mm total coated thickness pre painted galvanized iron sheet with micro ribbed profile and the insulation material will be chlorofluoro carbon and hydro chlorofluoro carbon free , high performance rigid polyurethane foam (PUF) conforming to IS 12436 having density not less than 40±2Kg/M3, Thermal conductivity (K-Value) 0.024 W/m.K measured at 10 degree C mean temperature along with necessary flashings such as L flashing, C flashing etc& accessories such as screws ,fastners ,sealants etc for fixing the panel etc., complete complying with standard specification. 50mm (+38mm) thick PUF roof panel

Supply and fixing of Semi glass terracotta tiles on existing steel members including cost of material, Labour etc., complete.

Fabricating supplying and fixing of roof with Poly carbonate sheet of 6mm thcik with any colour or any other approved design and to be fixed with shelf tapping screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying and fixing G.I. Gutter made of 20 B.W.G. galvanised iron sheets and G.I. valleys made of 18 B.W.G. galvanised iron sheets including fixing,etc.,complete.(ISI STD)

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification.

Providing and painting all steelwork with (i) one primer coat of inorganic zinc silicate (min. Vs 62%) 50 micron (ii) one coat of epoxy HB MIO brown (min Vs 55%) 75 micron (iii) one coat of polyurethane paint (min. Vs. 40%) 40 microns including all material,one coat of epoxy HB paint (min. Vs 60%) 100 microns (iv) labour, scaffolding etc. The surface shall be shot blast to SA 2.5 standard using grit. The paint shall be applied as manufacturer's specifications and the item shall include necessary testing, test certificate etc.

Providing, assembling and Supplying of Double Glazed Performance glass, heat Strengthened clear Glass (IGUs) of size and shape as required and specified of approved, comprising of an outer heat strengthened clear glass of following thick of approved colour and shade with reflective soft coating on surface #2 and an inner heat strengthened clear glass of following thick , spacer tube 12mm wide , dessicants, including primary seal and secondary seal ( structural silicon sealant ) etc. all complete for the required performance , as directed by the engineer -in - charge. The heat strengthened clear glass having properties as visible Light transmittance (VLT) of 25 to 35 %, Solar heat gain coefficient less than or equal to 0.27 and U value of 3.0 to 3.3 W/m2 or lower degree K etc. The IGUs shall be assembled in the factory/ workshop of the glass processor. For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. 8mm+12mm+6mm

FRAME WORK FOR STRUCTURAL GLAZING: Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass....... d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-incharge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supply and Installation of Anutone Strand Nubby, square edge, magnesite-bonded,2mm wide pinewood fibre core,fully encapsulated with texture finish,Green Pro certified ceiling tile of size 595x1195x15mm thk having volume density 400Kgs/m3, weight 6kg/m2 suspended using 0.3mm thick Anutone Skelet Trelis T15 metal grid system.Anutone Skelet Trelis T15 ceiling grid system, of 600x600mm module includes Anutone Skelet WA15W30 with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centres.Then suspend the Anutone Skelet MT15W36 with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of Anchor Bolt, Soffit Cleat and Suspension Rod with Levelling Clip at 1200mm centres. Anutone Skelet CT15W12 with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centres in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 in direction parallel to the Main T15 to result in 600x600mm module. Anutone Strand Nubby panels of size 595x595x15mm thk shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters Fire (Class) – 1 & P Acoustics – NRC upto 0.9 (For E600 Mounting) Thermal conductivity (W/mk)– 0.07 Climate (°C, RH) – 50, 95 Light reflectance (%) – 85 Green (VoC, RC %) – Low, 30

Supply and Installation of Anutone Strand Nubby, square edge, magnesite-bonded,2mm wide pinewood fibre core,fully encapsulated with texture finish,Green Pro certified ceiling tile of size 595x595x15mm thk having volume density 400Kgs/m3, weight 6kg/m2 suspended using 0.3mm thick Anutone Skelet Trelis T15 metal grid system.Anutone Skelet Trelis T15 ceiling grid system, of 600x600mm module includes Anutone Skelet WA15W30 with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centres.Then suspend the Anutone Skelet MT15W36 with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of Anchor Bolt, Soffit Cleat and Suspension Rod with Levelling Clip at 1200mm centres. Anutone Skelet CT15W12 with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centres in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 in direction parallel to the Main T15 to result in 600x600mm module. Anutone Strand Nubby panels of size 595x595x15mm thk shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Technical Parameters Fire (Class) – 1 & P Acoustics – NRC upto 0.9 (For E600 Mounting) Thermal conductivity (W/mk)– 0.07 Climate (°C, RH) – 50, 95 Light reflectance (%) – 85 Green (VoC, RC %) – Low, 30

FALSE CEILING WITH GYPSUM BOARD Providing and fixing suspended false ceiling using SAINT - GOBAIN GYPROC or Equivalent make which includes providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 610mm centres. 12.5mm Gypboard is

Supply and installation of 70mm thick Tufbloc magnesia drywall partition system (having high water & fire resistance) which includes one layer of Anutone Tufbloc Square edge of size 1200x2400x12mm having density 1000kgs/m3, weight 12kg/m2 fixed on the either side of GI strut channel framework. Framework includes Floor/ Head (FC50) GI channels having thickness 0.55mm, length 3600mm, equal flanges of 32mm and web of 50mm fixed to floor and ceiling with suitable fasteners at 300mm centers staggered. Noise and fire rated silicon sealant to be caulked along the perimeter of the partition frame before fixing channels. Then Stud channel (SC48) having thickness 0.45mm, length 3600mm, unequal flanges of 34/36mm and web of 48mm should be placed into the floor/head channel positioned vertically at 600mm centers. Extra reinforcement to be provided at openings (doors, windows, etc.,) Anutone Synth PF having thickness 50mm, width 600mm, density 1000gsm filled between the Studs and held in position by using chicken wire mesh/cross bracings/pasting on one side of the boards. The first layer of Anutone Tufbloc 12mm thick should be fixed on one side of the Stud framework in a staggered pattern by using suitable metal fasteners at 300mm centers. Second layer of Anutone Tufbloc 12mm thick should be fixed other side of the framework similar fashion as the first layer. 4mm gap should be maintained between boards on all sides. 4mm gap to be filled in fully to depth of board by using Anutone Seam kit as per given recommendations. Technical Parameters Core - Magnesia Fire Rating – upto 150 mins Acoustics – STC upto 50 Climate (OC RH) – 50, 99 Termite resistance – Yes Moisture Absorption - 6.8% after 2hrs and 11.3% after 24hrs soaking Wet Expansion - < 0.02% from ambient to saturation Dry Contraction - ≤ 0.02% from evaporation Moisture Movement - 0.02% Light reflectance – 80% Green (RC %) – 30 Hygiene (VoC, Clean room) – Low, Class 1 Strength - Antisag Impact - 4kg hammer 175mm

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 7.3 % open area), backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2,rear scoring with perf 10mm at 20mm pitch, tongue-groove edge for a seamless look, flame resistant (BS476 part 7) , of size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 11Kg/m2 (L16), installed by using GI Strut framework system.The GI Strut framework system shall include Strut CC25 fully knurled, sectional thickness 0.55mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the wall positioned horizontally or vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC25with the help of fasteners at every 400mm centers Anutone Slats Surco lite of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. The system is backlined with Anutone SynthPF 5x25 adhered on wall with dab spots of Anutone stick S7 adhesive. Technical Parameters Fire (Class) – BS476 part 7 , Acoustics – NRC 0.75, Thermal conductivity (W/mk)– na, Climate (°C, RH) – 50, 70, Light reflectance (%) – 75 (Maple Arce),Green (VOC, RC %) – E1, 25

Providing & fixing in position 5mm thick fluted glass panels including cost of Material, Labour, lead etc., Complete.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 7.3 % open area), backlined with Soundtexblack acoustical fleece of 0.27mm thick, surface density 63g/m2,rear scoring with perf 10mm at 20mm pitch, tongue-groove edge for a seamless look, flame resistant (BS476 part 7) , of size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 11Kg/m2 (L16), installed by using GI Strut framework system.The GI Strut framework system shall include Strut CC25 fully knurled, sectional thickness 0.55mm, length 3600mm, web 50mm, depth of 25mm and equal flanges 15mm is fastened to the wall positioned horizontally or vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC25with the help of fasteners at every 400mm centers Anutone Slats Surco lite of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. The system is backlined with Anutone SynthPF 5x25 adhered on wall with dab spots of Anutone stick S7 adhesive. Technical Parameters Fire (Class) – BS476 part 7 , Acoustics – NRC 0.75, Thermal conductivity (W/mk)– na, Climate (°C, RH) – 50, 70, Light reflectance (%) – 75 (Maple Arce),Green (VOC, RC %) – E1, 25

Supplying and Fixing Signage Corten steel 2mm thick as per approved design and pattern including Cost of material, labour etc., complete.

Supplying and Fixing Water Proof Plywood 19mm thick

Supplying and Fixing Aluminium Profile for flooring

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Supply and providing Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

75mm dia

110mm dia

160mm dia

50mm dia

Internal Water Supply - CP.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

15mm dia

20mm dia

25mm dia

32mm dia

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position indian make bewelled edge mirror of approved quality and brand of size 600 X 450mm wth necessary plastic back, PVC frame with bottom stand of approved colour with brass screws,rawal plugs etc., complete complying with standard specifications

Supplying and fixing best approved quality C.P.Soap Tray of size 150mm X 100mm including cost of Teak Woodplugs, brass screws complete complying with standard specifications.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications

Suppling and fixing in position 15mm diameter brass / C.P screw down tap / pillar tap / swan neck tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary. C.P screw down tap

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing the best quality approved make of bip cock with C.P. health faucet wall hook one metre long flexible tube, angle cock with wall flange including cutting and making good the walls wherever required etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Executive Engineer before use on work.

Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mmwith all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia ‘B’ Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc.

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete - Depth per cm

Supplying & fixing in position first quality & approved variety of 50mm dia C.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

25mm dia

32mm dia

Constructing Brick Work Masonry manhole various size of deep in cement mortar 1:3( 1 Cement: 4 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame of size 600x600 mm , PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Executive Engineer before use on works) (SOR)

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit etc. using only calyx rigs.

Reaming from 200mm dia pilot bore to 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992

200mm dia CS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supplyinga dn fixing 5.0 HP Monoblock Pump including all accessories

Supplying and Fixing Liquid Soap dispenser - Parryware- T6513A1 or Equivalent

Supplying and fixing PARTITION MOUNTED SANITARY NAPKIN DISPOSAL Color: Silver Installation Partition-mounted Operation Manual Finish :Satin Shape: Rectangle Capacity 4.7 Liter. Product Dim. L 330 x W 107 x H 505 mm

Supplying and fixing Flash touch-free infrared hand dryer with 1150W rated power & carbon brush motor. Jaquar - HDR-SSF-AK2807 or Equivalent

Supplying and fixing Paper holder with flap recessed type (Stainless Steel) Jaquar AHS-1553 or Equivalent

Supplying and Fixing Manhole Cover SFRC

600mm x 600mm

750mm x 750mm

900mm x 900mm

6 SEATER LEARNING CENTRE TABLE - 2400mm x 1200mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 2700mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

4SEATER LEARNING CENTRE TABLE - 2100mm x 1100mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 2700mm x 900mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:2

8 SEATER LEARNING CENTRE TABLE - 3600mm x 1200mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

CHILDRENS LEARNING CENTRE TABLE -24700mm x1200mm x 450mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

INDIVIDUAL SEATER LEARNING TABLE - 800mm x 600mm x 750mm - Supply and fixing of Rectangular Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. 3600mm x 1200mm length of table top is Supported on legs 50mm dia MS Hollow Section powdered coated to approved shade with 4mm bush at the bottom. Supported Legs are in the four corners & inbetween. For Legs Horizontal Support 75mm x25mm MS Hollow Section powdered coated to approved shade, Flip up wire manager is provided on top. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

SOFA SEATING - Supplying of Sofas with velvet/leatherette fabric upholstery on back and seat. Seat made of minimum 28 density foam and back made of microfiber or 32 density foam. Legs in wood or SS.1 seater size - 2'8" x 2'6"

3 Seater

Single Seater

OFFICE TABLE - 1555mm x 600mm x 750mm - Supply and fixing of Table top of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. Supported on 19mm BWR plywood clad with 2mm thick HDF duco paint to approved shade finish Flip up wire manager is provided on top. . The table will have one number of drawer and 1 No of storage shutter of size - 402mm x 600mm x 590mm with lockable drawers . Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

ROLLING CHAIRS - Supplying & placing of Mesh chair of Medium Mesh Back Chair, Cushioned Seat, Adjustable Lumbar Support, Gaslift, Synchro Mechanism, Adjustable Arms, Nylon Base. The rate should include Materials lead and lift, cleaning , etc.

SINGLE STUDY CHAIR: Supplying and Placing Single Study Chair with Full writing pad high density fibre board, Seat and Backrest: Specially blended glass filled nylon, 22mm dia M.S Taubular understructure, Bottom Bock rack, Powder Coated Finish

Supplying and Placing Teak wood with pirambu pinnal Chair With Armrest, Seating Height-18 Inch, Color: Brown And Beige, Maximum Load Capacity:150kg, Warranty: 2 years

• WOODEN RATTAN CHAIR- Supply and placing of solid teak or rosewood, the chair features a hand-woven cane seat and backrest, stretched tightly over a slightly inclined wooden frame. Its angular "V"-shaped legs, integrated flat armrests, and ergonomic design with a low, reclined backrest make it both functional and visually striking. Constructed using traditional mortise-and-tenon joinery, the chair should be finished with a clear or dark lacquer. Measuring approximately 28–30 inches in height, 20–22 inches in width, and 25–27 inches in depth, with a seat height of 15–17 inches

• CHILDREN WOODEN CHAIR- Supply and placing of solid hardwood, walnut or teak, showcasing natural grain and warm tone. It includes a gently curved backrest for ergonomic support, complemented by a padded seat upholstered in durable fabric for enhanced comfort. The chair stands on four sturdy, straight legs reinforced by horizontal stretchers. With a seat height typically 25 cm. The wood is finished with a clear or matte lacquer to protect the surface.

BOOK RACK - Supply and placing of book rack features a combination of CRCA steel as the primary material and particle board as the secondary material, ensuring durability and a modern aesthetic. With dimensions ranging from 3600 X 600X 2100mm. The product should be GreenGuard certified or Godrej or similar make.

LOCKER & FOOTWEAR STORAGE - 4152mm x 300mm x 900mm - Supply and fixing of L Shape Locker & Footwear Storage unit made of 19mm BWR plywood with laminate finish of approved shade.Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:4

RECEPTION DESK - 1600mm x 600mm x 750mm - Supply and fixing of Reception Desk of 40mm consists 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish and partition consists of 20mm Half round wooden beeding PU satin Matte fixed to 19mm BWR plywood finished with veneer on the one side and top of partition 2 Nos 19mm BWR Plywood clad with teak veneer crown cut PU polish satin matte with approved finish. Flip up wire manager is provided on top. . The table have storage of size - 800mm x 600mm with shutters . Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing.

PANTRY STORAGE :2173mm x 600mm x 750mm - Supply and fixing of Pantry Storage consists of 2 Nos of 19mm BWR Plywood clad with 4mm thick teak veneer crown cut PU polish satin matte finish. Supported on 19mm BWR plywood clad with 2mm thick HDF duco paint to approved shade finish Flip up wire manager is provided on top with storage and shuttering. Complete with all hardwares of ebco/hettich make or similar. etc. The rate should included debris clearing, Materials lead and lift, cleaning , etc. complete as per drawing. Refer Detail No:4

COMPUTER TABLE - 1300mm x 600mm x 750mm - Supply and fixing of Computer Table with Key board drawer and table top, Drawer with 6 lever lock with set o 2keys of non corrosive materials, Sliding of keybaord - Provided with two telescopic channels with balls,

OFFICE CHAIRS - Supplying & placing of The Seat and Back Cushion of the chairs should be pressed on 12 mm hot press moulded ply. The seat cushion of the chair should be 50mm thick with density of 45±2 Kg/m^ polyurethane moulded and back cushion should be 46mm thick with density 33±2 Kg/m^. The polyurethane foam shall be as per manufacturer's specification. The hardness of foam shall be 16±2 kgf as per IS7888 for 25% compression and it should be covered with black or brown fabric shade, The arms of the chair should be black, The lift mechanism should be pneumatic or hydraulic, The tilting mechanism should be adjustable with following features: a. 360° revolving type. b. Single point control. c. Front-pivot for tilt with feet resting on ground ensuring more comfort, d. Tilt tension adjustment. The pedestal should be five legged injection coated with black nylon polyurethane and fitted

Providing and laying 20mm thick FALSE WOODEN FLOORING of PERGO ORIGINAL, Armstrong, Egger or equivalent (matt finish) consisting of panels of size 1194mm x 194mm or as per manufacturer specification having class of use - 23/33, wear resistance level of AC5 as per EN 13329 with a high pressure surface treated with aluminium oxide and a specially patented SURFACE GUARD + on top of a high density fiber board with a density of 910 Kg/ cum. The panels having a click system tongue and groove joint to secure a long lasting joint with the edges duly impregnated with paraffin. The Floating laminate flooring shall be laid over a 0.20mm thick polythene film to form a vapor barrier and 2mm to 3mm thick approved FOAM The panels used shall be of high solidity, high impact strength, high temperature resistance without change in shape). Each panel shall have click system (tongue and groove profile) and to be laid in approved pattern with suitable glue as per manufacturers specifications including alround suitable egde profile alround/wherever required for firm end lockin

Supplying and erecting in position of 250 Litres capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works,wherever necessary to install the System in position and intact.

Supplying and fixing Writing WhiteBoard 4′ x 6′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing Writing WhiteBoard 4′ x 4′ with the following specifications. Non Magnetic , Melamine writing surface Triple Layer writing board Suitable for marker writing and effortless erasing with the help of a Duster. Comes with anodized aluminum frame & ABS corners alongwith Wall mounting hooks to support and sturdy looks also give a longer life to the board Best suited for Office home and educational & Instituitional use

Supplying and fixing pin up board 4'x6' with the following specifications. Material - Alloy Aluminium Frame, Softboard Core, Premium Flocked Fabric (Velvet) Cloth Surface & Virgin ABS Corners, The back of the board can withstand repeated use and will keep the documents in place with a secure hold. With its strong and elegant frame, the YAJNAS bulletin board will add a perfect feel to the environment of your office, home or school. This board is the perfect blend of stylish and sturdiness that will make a great addition to any space. The Bulletin board corners are designed to be equally strong. The surface will re-close when push-pins are removed, making it long-lasting. Precision riveting of these corners ensures that the edges are properly sealed, thus making the product weatherproof while imparting a seamless finish to it.

Stainless Steel Plain Pedal Bin With Plastic Bucket And Lid| Trash Can, Round Shape 12 Litre Capacity Dustbin with Step-On Opening Mechanism

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller.

Supplying and Planting of Cassia fistula tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Sterlitzia nicolia sapling in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Heliconia pssitcorium tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Calathea lutea tree sapling of height 120 – 180 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Plumeria alba tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Cymbopogon citratus tree sapling of height 210 – 240 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Bermuda grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lobelia erinus shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Brassia variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Schefflera variegated shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hymenocallis littoralis shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lysimachia nummularia including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of zephyranthes -yellow and white including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of ruellia simplex including loading and unloading charges, ransportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying of Rectangle (3') pot of 90 inch dia and size 45*45 in Centimeter, Various size pots made up of 6mm rod & chicken mesh with cement moulded pots and designer painting with various size plates including loading and unloading charges, transportation, etc as directed by the site in-charge."

Supplying of Plastic pot size of dia 24 inch brown with plates including loading and unloading charges, transportation, etc as directed by the site in-charge.

LT CT TNEB METER BOX: 'Supply, Installation, testing and commissioning of compartmentalised LT CT 3Phase, EB Metering box of outdoor weather proof type with MS mounting stand, Copper busbars with supports, Test Terminal Blocks, CTs, Internal control wiring etc., as per local TNEB standards

Supply and fixing of 200 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

MAIN LT PANEL: 'Supply, Installation, testing and commissioning of 3Phase, 415Volts, Main LT Panel board of Indoor, Cubicle floor mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base frame, double internal earthing arrangements, 200Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: EB Incomer : 1 No. 200Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM DG Incomer: 1 No. 200Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Common C/O Incomer: 1 No. 200Amps, 4Pole Automatic Changeover Switch with EB ON and DG ON LED Indication lamps Metering : 2 Set of RYB LED Indication lamps 2 Nos. of Multifunction Meter with RS 485 2 Set of Current Tranformers (200/5A, Cl-1), 1 No. 200/5A CT for APFCR 2 Set of Control MCB and Electrical Interlocking between EB & DG Incomers Outgoings: 2 Nos. 100A, 25kA, TP+N, TM MCCB with Ext. RHOM (APFCR & Spare) 6 Nos. 63A, 25kA, TP+N, TM MCCB with Ext. RHOM (VRF, PDB-1&2, Ex.LDB & Spare) 9 Nos. 32Amps DP MCBs

APFCR PANEL - 40KVAR: 'Supply, Installation, testing and commissioning of 3Phase, 415Volts, APFCR (Capacitor) Panel board of Indoor, Cubicle floor / wall mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base /wall frame, double internal earthing arrangements, 100Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: Incomer : 1 No. 100Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Metering : 1 Set of RYB LED Indication lamps 1 No. VAF Meter with RS 485 1 Set of Current Tranformers 1 No. 6 Stage APFCR Relay 2 Set of Control MCB Outgoings: 1x20kVAR Heavy Capacitor bank controlled by 1x40A, 4P MCB, 3x05kVAR Heavy Capacitor bank controlled by 1x25A, 4P MCB, 1x03kVAR Heavy Capacitor bank controlled by 1x20A, 4P MCB and 1x02kVAR Heavy Capacitor bank controlled by 1x20A, 4P MCB including ON-OFF Push buttons, internal control wiring, etc.,

DG SET - 100KVA with Standard Control Panel : 'Supply, Installation, testing and commissioning of 1 x 100VA, Silent type Diesel Generator Set complete with suitable size Acoustic enclosure Diesel Engine suitable for Generator application, developing 1500RPM with an overloading capacity of 10% for one hour in any 12 continuous hours operation generally confirms to BS:5514, directly coupled to 100KVA at 0.8 Power factor, 415V, 3Phase , 4wires, 50cycles per second self excited, self regulated, with brushless excitation, Alternator generally confirms to BS:5000/IS:4722. DG set shall be complete with radiator, residential type silencer, electronic governor, cable termination box, MS mounting frame, fuel piping, diesel day tank, 24VDC Battery, Battery mounting frame, oil level indicator with gauge board, and all other accessories as per standard specifications. 'Diesel Generator set shall be mounted on cushy foot or similar type of vibration Isolators. The cost of Exhaust pipe shall be excluded in this item. The DG Set shall be suitable for auto-mains failure start and auto / manual operations. The DG Should be supplied with Auto-Start-Stop Control panel with suitable rating switchgear.

LDB-1 & 2, ELDB-1&2 and RPDB: Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

External LDB Supply and fixing of 7 segment 4way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single/three phase MCB outgoings and separate 4 way provision for accommodating one no.63A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 63A 4 pole ELCB / RCD (totally 8 ways in one segment), (3x 4 ways in each segment) and separate provision for 6A to 32A SP MCB-12Nos. / Isolators (totally 12nos.) for sub incomers in 3 nos.63A DP MCB segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only.

AC/PDB-1 & 2: Supply and fixing of 7 segment 8way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 63A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 63A 4pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and separate provision for 6A to 32A SP MCB-24Nos / Isolators (totally 24 nos.) for sub incomers in 3 nos 63A DP MCB segments with label holder and provision for taking up cable for size not less than 35 sq.mm with the following on wall with earth connection only.

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and laying of 2 x 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 2 x 6 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 300mm width and 50mm height with all the fixing accessories

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire and making good of the concealed portion

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 10 sq mm copper wire with painting of suitable colour.

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 6 sq mm copper wire with painting of suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm copper wire and making good of the concealed portion wiith suitable colour

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Primary)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - (Secondary)

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 60W LED street light fitting with LED with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

Supply and erection of 36Watts, 1130mm Long LED Linear light fitting suspended from the ceiling with hanging supports, end cap, PVC unsheathed copper leads from terminals to the fitting and fixing accessories.

Supply and erection of 15Watts, Round type COB/ Wall Bamboo LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting and fixing accessories.

Supply and erection of 11Watts, 1000mm Height IP65 rated Bollard type light fitting with MS base, concreting and masonry work for fixing the post, connecting wires, and fixing accessories

Supply and erection of Name board lighting using IP65 rated LED with connecting wires and all the fixing accessories

Supply and erection of 9Watts, 1feet long, Fancy type wall mounted LED Light fittings with connecting wires and all the fixing accessories

Supply and erection of 15Watts, Round type Globe or circular pendent LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting

Supply and installation of Printed Ceiling- Supply of European Standard Premium PVC Membrane installed with Aluminium Profile. PVC harpoon welded with high frequency on the perimeter of the membrane according to shape and size -Thickness of Membrane - 0.18mm -Weight - 250 - 300 gsm +/- 2% -% of light transmission - 75.00% -Fire Rating - BS1D0 in accordance with EN 13501-1. -Warranty - 10 years -No Heavy Metals - ROHS Certified -Manufactured in ISO 9001:2015 certified factory in India including connecting wires and clamps screw and etc.

Supply and Installation of Stretch Lighting - 6000K - 24V Osram Rigid Block LED, 160 Degree Best Viewing Angle with PMMA Lens ROHS Certified Power Consumption : 4W Per Rigid Block LED SMPS - Iceil Drive with 3 Year Warranty LED Life span : 30000 Hours / 5 Years connecting wires and clamps screw and etc.

Supply and erection of Profile light (LED) fitting suspended from the ceiling using 50Watts, 2260mm Long LED Linear light fitting suspended from the ceiling with hanging supports, end cap, PVC unsheathed copper leads from terminals to the fitting and fixing accessories

Supply and fixing of 8W Light fitting (IP67) Inground fixture with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 28Watts GATE FIXTURE FITTING with cool day light suitable for wall / roof sheet mounting, made out CRCA powder coated body,IP65 aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and erection of 450mm Sweep Wall mounted type fan with fixing accessories.

Supply and fixing of 300mm (12") sweep(Heavy Duty) AC exhaust fan complete with necessary wall opening and making good of the wall .

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep AC exhaust fan.

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and erection of 17.2mm, 3mtr long, Copper Bonded earth rod with backfill compound, including civil works, heavy duty Plastic Chamber cover withstand load of 60kN, etc., as per IS 3043 standards

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth.

Supply and erection of 40-63Amps, 4Pole MCB with IP65 rated thermoplastic enclosure for ODU nearyby control

Supply of '2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

Supply of First Aid Box complete with all First Aid Medicines

Supply and fixing of Shock Treatment chart with Glass frame

Supply and fixing of 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Supply and fixing of Fire Extinguishers Co2, 4.5Kg confirming to TAC norms

Supply and fixing of Metallic Danger Board as required by the Electrical Authorities (415Volts & 230Volts)

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase Input & Single Phase Output) System with sealed maintenance SMF Type Battery - 2Hours back up with Battery Stand, interconnection cooper cables, etc.,

Supply and fixing of DP MCB sheet steel enclosure with 1 no 32A DP MCB switch with necessary fixing accessories

Supply and erection of Canon Digital Photocopier (Xerox) Machine IR-3300 / 3235 Type of Product : Laser Multi functional Core Functions : Print, Copy, Scan & Send First Copy Time : 3.9 Sec Multiple Copies : 1 to 999 Sheets Print Speed : 45ppm The laser beams engrave the image or text that you have sent to print on the surface of the drum. When using a copier this process is done using light, the light scans the page required for printing and converts it into an image

Supply and erection of All-in-one Desktop of HP 27-cb1456in Core i5 (8GB DDR4 /Windows 11 Home/27 Inch Screen/27-cb1456in) with 600VA UPS, Keyboard, Mouse, 27 inches, 11th Gen Intel Core i5-1235U 6 x 1.8 GHz (Turbo Speed upto 4.2 GHz) Cores Hexa Core, 12 Threads, 18 MB Cache, UHD Graphics 730 Graphics, 8 GB DDR4 RAM Smallest and 512 GB SSD. Ethernet (LAN), HDMI, Multi Card Reader, WiFi, Bluetooth v5.0 3 x USB 3.0, 1 x USB Type-C and Inbuilt Microphone

Supply and erection of BenQ TK700Sti (3000 lm / 1 Speaker / Wireless / Remote Controller) 4K UHD HDR, Excellent Colors 96% REC 709, Upto 200inches screen,Sports Mode,Android TV,16ms Low Input Lag,Google Cast,3D Keystone Smart Home Cinema Short Throw Projector (White) Aspect Ratio - 16 : 09, Brightness- 3000ANSI lumes Connector type - Wifi, Bluetooth, USB & HDMI Contrast Ratio- 1000:1, DIsplay Resoultion-3840 x2160p Life Hours- 15000Hrs, Power - 1Phase, 240Volts, 305Watts

Supply and installation of Wheel Chair Platform Lift with the following specifications HYDRAULIC WHEELCHAIR LIFT 1) 3 PHASE POWER PACK 2) 0.5 M/SEC SPEED 3) LIFT CABIN SIZE 1200MM X 900MM 4) ACP SHEET FOR FRAME COVER 5) 7.7KW POWER PACK 6) SS304 CABIN 7) CABIN FLOOR MATE 8) ARD (POWER CUT LIFT COME TO GROUND LEVEL) 9) ALARAM IN CABIN 10) ENTER GRILL DOOR 11) HALF CABIN HEIGHT 4 OF 3 FEET

Supply and installation of All-In-One Digital Metal Podium with the following specifications: Digital Podium is a complete solution for any classroom, boardroom / training room and Auditorium. It has a built-in sound system (Amplifier, Gooseneck Microphone, Wireless Microphone, etc..) and can be interfaced with all multimedia devices and facilities that the Presenter might employ as teaching or communication tools. a) Type: Free Standing, Lockable Caster Wheel b) Construction : 1.6 mm CRCA Steel, Polymer Powder Coated Metal Top c) Storage : Keyboard, Mouse, Drawer for Visualizer , Side Shelf for Laptop d) Monitor : Built in Touch Monitor 21.5” with motorised tilt Mechanism e) Resolution : 1920 x 1080 (Full HD) f) Features : Power ON / OFF, Display ON/ OFF, External PC Input, VGA/HDMI g) I/O PArts: USB 3.0 x 1, HDMI IN & LAN: RJ-45 LAN Port h) Wireless Microphone System: VHF Hand Held Microphone x 1, VHF Collar Microphone x 1, Wireless Microphone Receiver x 1 i) Gooseneck Microphone: 80 cm Length, with Light Double Soft Copper Tube, 1.5m Wire, 3 cores Cannon Plug. j) Amplifier and Speakers: 120 w RMS Amplifier and 2 x 30 watt inbuilt Speakers/ 2 x 30 watt wall speaker k) Power SUpply: 230Volts, 1Phase, 120Watts l) 4GM RAM, 1TB SATA H/D, Built-in WiFi, i3 - Windows10 k) Annotation Software: Annotation Features like draw, choose, pens, annotate, erase, color, shape, size, text, edit, fonts, stamp, move, capture, picture, video, save, rotate, undo, image, gallery, print, floating keyboard, background etc. Network classroom feature to conduct remote teaching by having interaction through all type of media Audio, Video and Text. (Approx. Size: 750 x 700 x 1200 (L x W x H))

Supply and erection of 20-30Watts Ambient Circuit ype LED light fitting suspended from the ceiling with hanging supports, PVC unsheathed copper leads from terminals to the fitting

Supply and erection of 10Watts IP-65 rated Wall / Column mounted type Up-Down LED Light fitting with fixing accessories

Supply and erection of LED Strip light fitting with suitable driver and fixing accessories (5Watts / Meter)

SOLAR PV PLANT 'Supply, erection, testing and commisioning of '30 kWp On Grid Solar PV Plant' comprising of: i) Solar panels of type Mono Crystline, PERC, etc. ii) Power Conditioning Unit (PCU)with MPPT, Inverter, Controls, Protection Devices, Interconnecting D.C. cables, Connectors, Junction Boxes and accessories. iii) D.C. D.B iv) A.C. D.B v) A.C. cables and accessories vi) Lightning arrestor, earthing, etc. vii) Module Metallic Mounting Structures viii) Installation, Testing and Commissioning corresponds to BIS and IEC requirements

Supply and erection of complete set of Signages (Entry, Exit & Other signages) as per standard building requirements

Supply, Installation, Testing and commissioning of 32 channel 2 SATA NVR, with 8TB Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony.

Supply of 4MP, Internet Protocol fixed BULLET CAMERA/DOME CAMERA (INDOOR & OUTDOOR)with following specification: a) 1/2.5" Progressive Scan CMOS, b) 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) c) Face Detection d) 120dB WDR, e) BLC/3D DNR/ROI, IP67 compliedf f) On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, g) Shutter Speed 1/3 s to 1/100,000 s, h) 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, i) rotate: 0° to 360°, 2.8 mm, j) horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, k) Lens Mount M12 & IR Range I5: up to 50 m, l) Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, m) Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W n) Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. with Camera Stand. (Make: Dahua/Panasonic)

Supply, Installation, Testing and Commissioning of 43" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote(Make: Sony/ LG /Samsung).

Supply and Clamping of CAT 6 unarmoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Supply and Fixing of Rack with Accessories -Higher end 9U Rack with fan extra for the above rack. (speaker/data/cctv)

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply, Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and Installation for 1KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up and battery stand .

Supply and fixing of outdoor 4X6 PVC box with 102mmX77mmX102mm with all fixing accessories.

Supply, installation, testing and commissioning of Long Range Wifi Device of following Specification: Networking Interface: (1) GbE RJ45 Port Power Method: PoE+, Pasive poE(48V) Max TX power: 2.4 GHz, Antenna gain: 2.4 GHz Mounting: Wall or Ceiling Mounting Wifi Satndards : 802.11a/b/g, Wireless security: WPA-PSK, WPA- Enterprises(WPA/WPA2/WPA3) VLAN: 802.1Q Concurrent Clients: 300+

Supply, Installation,Testing & commisioning of 480 watts P.A Booster Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent)

Supply and Fixing of Rack with Accessories -Higher end 36U Rack with fan extra for the rack. (PA System)

Supply, run, testing and commissioning of 2Core x 1.5sq sqmm PVC insulated Armoured Speaker Cable in suitable 25mm dia Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply and Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply, Fixing and Termination of RJ 11 Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply & Installation of CAT 6 PVC Module Box I/o socket & face plate single socket Erection and arrangement chargers (Higher end)

Supply and fixing of LAN Network Switches Un-Managed 10/100/1000 - 24 Port and 24 Port Patch Panel- Unloaded erection and arrangement chargers.

Supply, runing, testing and commissioning of 2 Pair Unarmoured 0.5mm Telephone cable in suitable Pvc Rigid pipe concealed on wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply, Installation, testing and commissioning of VRV/VRF air-conditioning system Cooling only comprising of Modular type high efficiency DC Scroll / Twin Rotary Multiple Compressor with DC inverter, High efficiency heat transfer Cooling Coil suitable for Environment friendly HFC R410A / R407C refrigerant, Air cooled propeller type condenser fan with DC motor drive, interconnecting piping, insulation etc., Micro-processor control panel suitable for automatic operation, High speed calculation inverter control, active oil control mechanism incorporating all safety functions as per technical specifications & other points listed below. Unit shall have a minimum of 2 compressors. And each compressor shall run independently even though there is a failure in the other compressor. The unit mounted starter panel shall be complete with IP-55 protection consisting of power disconnecting switches with fuses, soft starters, for compressor motors, under/over voltage trip, single phase preventers, communication card which can accept 4-20 mA or 2-10 Vdc analog signal. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . 18HP - Inverter Scroll Compressor Modular VRF ODU

VRV/VRF Indoor Units (CASSETTE UNIT) Supply, Installation, Testing and commissioning of Indoor Cassette units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 2TR)

VRV/VRF Indoor Units (FCU - Fan Coil Units): Supply, Installation, Testing and commissioning of FAN COIL units. All the units should be supplied with Cordless remote control and Refrigerant Y joints with fixing arrangements, etc., (Capacity : 2.0 TR)

CENTRAL REMOTE CONTROLER FOR VRF / VRV SYSTEM (I-Touch Controller): 'Supply and erection of Central Remote Controller for controlling the below said parameter of the VRV system. Temperature, change of set temperature, ON-OFF controller ,scheduling and sequencing.enegry consumption. Unit alarm trip status. compressor run status. with BACNET and BMS Compatible. The iTouch is our advanced centralized controller. It can control up to 64 indoor unit groups (128 indoor units). It has independent cool and heat setpoints for occupied and unoccupied conditions. The iTouch Controller provides building owners, facilities/premises managers and maintenance operators refined and energy efficient control of Daikin VRVIII, VRV WIII, VRVIII-S and/or mixed VRVIII/VRV-IIIS/SkyAir indoor units. With its user friendly color icons and scheduling capabilities, this controller makes management of indoor units and other facilities equipment easy. The iTouch Controller is linked directly to the system via a Daikin DIII-Net connection without the need for a PC. Supports centralized control remotely using a PC with a Web browser (Optional).

Supply and erection of Refnut Joints with all accessories

Supply and laying of 50mm dia HDPE PVC pipes for drain with necessary supports and fittings.

Supply and laying of 25mm dia HDPE PVC pipes for drain with necessary supports and fittings.

Copper Piping with Gas and insulation: Supply, Installation, testing and commissioning including vaccumisation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing /brazing including accessories, insulated with Nitrile rubber Class-O tubular insulation / with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories asper specifications etc. as required : Gas line with 19 mm thick insulation and Liquid line with 13 mm thick insulation

Supply and erection of Gas line of 36.9 mm with insulation

Supply and erection of Gas line of 28.6 mm with insulation

Supply and erection of Gas line of 22.2 mm with insulation

Supply and erection of Gas line of 19.1 mm with insulation

Supply and erection of Gas line of 15.9 mm with insulation

Supply and erection of Gas line of 12.7 mm with insulation

Supply and erection of Gas line of 9.5 mm with insulation

Supply and filling of R410A Refrigerant Gas

Supply and erection of GI Hot Dip / Powder Coated 16 SWG Perforated type Cable Tray with 150mm width and 50mm height with all the fixing accessories for laying the refrigerant line

Supply, Installation, Testing & Commissioning of Factory fabricated Rectangular GI duct with galvanized sheet steel (GSS) confirming to IS 277 or Al sheets confirming to IS 737. The steel sheet shall be hot dipped galvanized with matt finish with coating of min. 120 GSM of zinc, The sheet thickness shall be as per CPWD specifications , GSS Duct Construction standards must conform to IS 655-2006 & For Factory fabricated duct should follow SMACNA -2005 Standards. 'GSS ducting shall be complete with all relevant accessories like splitters, vanes and Proper jointing (EPDM lining/cleats etc.) shall be done to prevent air leakages. The quoted price shall be inclusive of necessary accessories, Channel supports, Threaded rod,etc.

Supply, Fabrication and erection of fabricated ducting made up of GI Sheets of 24 Gauge thickness - 0.63 mm

Supply, Fabrication and erection of fabricated ducting made up of GI sheets of 22 Gauge thickness - 0.80 mm

Supply & installation of Thermal insulation of the sheet metal duct with 13MM closed cell elastomeric insulation of Class 'O' material with density of 40 - 55 kg/cum as per the thickness mentioned below, with fire retardant adhesive and joints sealed with 3mm thick, 50mm wide nitrile rubber self adhesive tape all in accordance with technical specifications.

Supply and fixing of extruded aluminum powder coated, supply and return Air Grilles / Diffusers with Volume Control Damper

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

100mm nominal dia ( Down comer + Terrace Pump room piping)

80mm dia

65mm dia.

50mm dia.

40mm dia.

32mm dia.

25mm dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 100mm Dia.

Supply, Erection, Testing and Commissioning of Cast Iron Body Butterfly Isolation Valves (PN:20) with necessary fittings and accessories like flanges, GI bolts, nuts & washers, painting etc. The Valves shall be of Lever operated valves for 150NB and below and gear operated valves for 200NB and above a) 25mm Dia.

Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS:5312( PN 16 ) swing check type with required flanges, nuts, bolts and gaskets etc. complete. A) 100mm Dia.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Supplying, fabricating, structural steel supports such as MS channels, angles, flats, rods as required at site with anchor fasteners, clamps, threaded rods, nuts, bolts, washers etc. complete with painting for pipe support.

Construction of Concrete Pedestal supports including M.S. Supports - 900 x 300 x 300 mm ( For supporting above Ground for Fire pipes )

Supply, erection, testing and commissioning of booster pump located at terrace level, capable of delivering 900 litres of water / minute at a pressure not less than 3.5.0kg / sq.cm at the top most hydrant, complete with suitable 15KW electrical driven centrifugal type pump with squirrel cage motor of Kirloskar make with bronze impellors, pressure gauge, pressure switch including suitable indoor wall mounting type control panel for auto start and manual stop etc., complete.

DOL Stater Panel: Supply and erection of wall mounting, dust & vermin proof, non compartmentalised, indoor type control panel fabricated from 14/16SWG CRCA sheet steel & painted with internal & external epoxy based powder coated as per IS:5 after seven tank pre treatments. 1 Set of 15 KW DOL starter along with MCB, Contactor, Overload Relay, Start / Stop Push Button with NO/ NC Elements, ON / OFF / Trip LED Indicating lamps, Auto/ Manual Switch, SPP, necessary power and control wiring, potential free contacts for BMS integration

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: KIARTAR / OMEX / EQUIVALENT)

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. A) 25mm dia.

Supplying, installing, testing and commissioning of `Y' - Type Strainer with Flanged ends - 100mm Dia.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Supply and fixing of Puddle Flange suitable for 100mm dia at Terrace tank with unions etc., complete.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 150mm dia.

Supplying, Installing, testing and commissioning of PN 16 lever operated Butterfly valve with required flanges, nuts, bolts etc., complete - 80mm dia.

Supply, Installation, Testing & Commissioning of Flow Switch with 2 NO and 2 NC contacts with necessary nipple and other fittings - 80mm dia.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Type: K-80 Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, Installation, Testing & Commissioning of Dial type pressure gauge Industrial type) with necessary nipple & other fittings - 100mm Dia.

Supply, Installation, Testing & Commissioning of Dial type pressure gauge Industrial type) with necessary nipple & other fittings - 80mm Dia.

Supply, Installation, Testing & Commissioning of 25mm Ball valve with necessary nipple and other fittings

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply and fixing of Hand held Fire Extinguisher - CO2 - 4.5 Kg with suitable Metal Floor stand MS fabricated painted in black colour

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of EMERGENCY/FIRE EXIT (450mmx150mm double side)

Supply and fixing of FIRE EXTINGUISHER (100mmx150mm single side)

Supply and fixing of "EXIT " (400mmx150mm double side)

Supply and fixing of "MANUAL CALL POINT" (100mmx150mm single side)

Supply and fixing of "EVACUATION PLAN with AUTO GLOW" in A2

FIRE DETECTION & ALARM SYSTEM: Supply, Installation, Testing & Commissioning of Addressable Fire Alarm Control Panel consists of display board which will have 160 Character Display with Touch key pad, Mother board 32 Bit Processor, In-built RS-485 Networking Circuit for peer to peer networking, In-built USB 2.0 Port, Loop Card having 254 devices of both detectors and modules in a single line circuit, SLC supports both Class A and Class B wiring Approval: UL Listed a) Single Loop Panel

Supply, Installation, Testing & Commissioning of Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility a) Multi Sensor - Heat Cum Smoke detector

Supply, Installation, Testing & Commissioning of Addressable Heat detector

Supply, Installation, Testing & Commissioning of Addressable Addressable Manual Call Point - Resettable type - with back box with Binary coded address setting with Status LED for 360° visibility.

Supply, Installation, Testing & Commissioning of Conventional type Horn / Strobe wall mounted type rated at 90 dBA @ 1m for Audible annunciation and 15cd minimum flashing at 1 Hz for visual indication.

Supply, Installation, Testing & Commissioning of Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications

Supply, Installation, Testing & Commissioning of Response indicator for all detectors located above false ceiling.

Supply, Installation, Testing & Commissioning of POWER SUPPLY : 24VDC Power Supply with 5 amp rating, having LED indications for Power supply ON,battery Fail, Battery Charging,battery back up etc.

Supply, Installation, Testing & Commissioning of 2 core x 1.5 sq.mm Red colour twisted pair shielded multi strand ATC armoured FRLS cable

AME CONSTRUCTIONS (BID ID -1272332)