SPL REPAIR OF ACCIDENT AND EMERGENCY CARE UNIT (MI ROOM) AT BLDG NO P-116 PH-I ) AT MH, PROVN OF GUARD ROOM WITH TOILET AT TECH GATE NEAR BALRAM BLOCK (BLDG NO HR-89) OF 1 TTR, 1STC AND CERTAIN REV AND MW WORKS OF AGE B/R-III UNDER GE WEST JABALPUR

Amount

Taking down cement plaster / terrazzo of any description thickness including raking out joints hacking for key scrubbing down with water incl removing of debries outside MD land complete all specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all specified and as directed.

M&L for applying two Coats of oil emulsion distemper over a coat of chalk whitening primer over 2 mm thick wall care putty on newly plastered surfaces of internal wall including preparation complete all as specified and as directed.

M&L for complete removal of existing treatment distempered and painted surfaces of old undecorated surface of walls and applying two coats of oil bound distempered over a coat of chalk whitening primer over 2mm thick wall care putty including preparation complete all as specified and as directed

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 25 mm thick cement concrete Type B-O 1:2:4 (Using 12.50mm graded aggregate ) complete all specified and as directed.

Dismantaling floor hearth or wall tiling/china mosaic including cement mortar bedding (but not backing ) , removing serviceable tiles to store and rubbish off the premises incl removing of debries outside MD land complete all as specified and as directed.

M&L for vitrified double charge tiles 8 to 8.5 mm thick (Square or rectangular) area of Each tile exc 0.36 Sqm but not exceeding 1.44 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed..

M&L for Granite (of any type ) 20 mm thick work (table rubbed and polished ) in steps ,jambs,pilllars,window cill,cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2)using marble dust with admixture of pigment to match with shade of Granite laid over over and including 20mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for rounding to edges of granite stone slabs one edge etc. complete all as specified and as directed.

Taking down chowkhats or frame (with shutter w/o taking off shutter from the frame) area not exc 1.5 Sqm Each complete all as specified and as directed.

Taking down chowkhats or frame (with shutter w/o taking off shutter from the frame) area exc 1.5 Sqm but n-exc 4 sqm Each complete all as specified and as directed.

S & F for 12 mm thick Toughned glass as in hinged doors, partitions automatic doors ,openable doors and similar work including cutting to shape, drilling holes required Glazing with beads fixed with metal panel pins or fixed with brass screws including necessary fitting stainless steel handles fancy type (handle size not less than 450 mm as approved by engg-in-charge),and required necessary fittings of Stainless stelel i.e. cleats ,rail,chanels as per site requirment including locking arrangement all size and type of stainless steel fittings as required complete all as specified and as directed. Note: Rates quoted are inclusive of all fittings.

Supply and fixing factory made u PVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 62x67 mm(tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding door with fly proof S.S. wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required).stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fastener 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets including E- Grid frame work complete all as specified and as directed.

S & F for 5 mm Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site on frame complete all as specified and as directed.

S & F for 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing on MS frame complete all as specified and as directed.

M&L for 20 mm dia stainless steel curtain rod fancy type with S/S finials/side brackets (both side) as approved complete all as specified and as directed.

M&L for Cutting holes in brick walls in exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft /loose soil.complete all as specified and as directed.

Excavation in trenches,n exc 1.5m wide and n exc 1.5m in depth ;for foundation etc.or for shafts well cesspit,maholes, pier holes etc.n exc 10 sqm on plan area as in soft /loose soil complete all as specified and as directed

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and as directed

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&Lfor Hardcore broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete,complete all as specified and as directed.

M&L for anti termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface,complete all as specified and as directed.

M&L for anti termite treatment the soil under plinth protection at the rate of 5 litre of emulsion per sqm of surface area,complete all as specified and as directed. .

M&L for anti termite treatment the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimetre wall, complete all as specified and as directed.

Returing, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil, complete all as specified and as directed.

Removing excavated material not exceed 50 m depositing where directed level n exc 1.5 mtr above the starting point, complete all as specified and as directed.

S&F, for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming,complete all as specified and as directed.

S&F Mild steel TMT bars 5mm to 10mm dia and cut to length bent to shape required, including cranking, bending and binding as in stirrups, spacers and binders etc. with MS wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish complete all as specified and as directed

Formwork to sides of pillars, posts, struts, piers, columns and stanchions,Rough finished surfaces of concrete,square, rectangular or polygonal,complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders,bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floor and beam etc. complete all as specified and as directed

Formwork to chajjas, troughs and similar items including edges fair finished complete all as specified and as directed.

Use & waste for form work to soffits of suspended slab such as roof slab, floor slab , landing and similar work; not exc 200 mm thick horizontal or sloping, finished fair and even complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide Rough finished surfaces of concrete complete all as specified and as directed

M&L for RCC -M-25 ( Design mix) using 20mm grades stone aggregate as in foundation including raft footings, foundation beams, plinth beams, bases of columns and the like complete all as specified and as directed.

M&L for RCC -M-25 ( Design mix) using 20mm grades stone aggregate as in Columns, pillars, piers,posts and struts complete all as specified and as directed.

M&L for RCC -M-25 ( Design mix) using 20mm grades stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M & L for RCC M-25 design Mix using 20mm graded aggregate in slabs supported on wall and beams and column in floors,roofs landing etc, complete all as specified and as directed.

M&L for RCC -M-25 ( Design mix) using 20mm grades stone aggregate as in chajjas roof projection etc complete all as specified and as directed.

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and as directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for roofs-

(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster, complete all as specified and directed.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

(c) One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm,complete all as specified and directed.

Supply only integral water proofing compound,complete all as specified and as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for Brickwork with fly ash bricks or brick tiles in brick on edge walls (less than1/2 brick thick), built in cement mortar (1:4) complete all as specified and as directed.

M&L for 15mm thick rendering on concrete/brick surfaces in CM 1:4 using with water proofing compound as per manufactures instruction finished even and smooth without using extra cement complete all as specified and as directed. ( Note:- WPC shall be measured and paid separately)

M&L for 5mm thick rendering in Cement Mortar 1:3 on Concrete Surfaces of ceiling etc finished surface Even and Smooth, without using extra cement,complete all as specified and as directed.

M&L for applying Two Coats of Cement Base Paint over a coat of alkali resistant primer on Newly Plastered Surfaces of external Walls including preparation complete all as as specified and as directed.

M&L for applying three coat of white wash as in ceilling on newly plastered surfacces including preparation complete all as specified and as directed.

M&L for 50 mm thick PCC 1:3:6 type C-1 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) are of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm mm thick as in vertical surfaces such as dados/skirting etc set and jointed in neat cement slury and in coloured cement to match Coloured over and including 10mm thick plaster in CM 1:4, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm,450x350 or 350x250 6 to 7mm thick on vertical surface such as skirting/dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick plaster in cement mortar 1:4 finished rough to fix tiles complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floor complete all as specified and as directed

Material and labour for 20- 25 mm thick machine cut kota stone flooring laid and jointed with neat cement slurry mixed with pigment to match the shade of the slab laid over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6 including rubbing and polishing complete all as specified and as directed..

M&L 18 to 20 mm thick machine cut kota stone as in vertical surfaces risers of steps , skirting, dado and pillars etc set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab laid over and including 10 mm thick rendering in cement mortar 1:4 including rubbing and mirror polishing complete all as specified and as directed.

S&F for 105x60 mm pressed steel door frame with one or more rebated incl necessary fixing lugs hings, lock strick , etc complete, all as specified and as directed.

S&F for 125x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

S & F for 35 mm thick factory made plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and as directed.

S & F 35 for mm thick 1st class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I,section 8,clause 8.24 (a) fitted to chowkhats for doors etc complete all as specified and as directed.

S&F for 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F, for 300mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F, for 200 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed

S&F for 300mm long mild steel ordinary rat tail rod pattern springs,including roller and roller plate complete all as specified and as directed.

S&F for steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for steel windows or ventilators, fixed type with glazing bars,complete all as specified and as directed.

S&F for mild steel framed work such as guard bars/grills,grating etc with end of bars shouldered and/or riveted or forged into spikes and similar works including one shop coat of zinc chrome primer complete all as specified and as directed.

S&F for stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and as directed.

S&F for 3mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F for 4mm thick figured glass, pinn headed type and glazing with oil putty in square n. exc 0.5 sqm each panes complete all as specified and as directed.

S&F for PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinf with MS square tube supplying & fixing in opening as per specificationn,complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails . M,S frame shall be covered with heat moulded plain colour PVC ,C, channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails , lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading , and jointed together with solvent cement , supplying and fising in the frame at site as per specification and drawing,complete all as specified and as directed.

S&F, for 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin,Type-B-21 complete all as specified and as directed.

S&F, for 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed

S&F for 125mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on newly wooden surface of any description over 10 cm width or grith including preparation complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint, over a coat of red oxide primer on newly steel surface of any description over 10 cm width or grith including preparation complete all as specified and as directed.

M&L for Cutting holes in brick walls in exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

S&F for 15mm bore Tubes medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors,complete all as specified and as directed.

S&F for 20mm bore Tubes medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors,complete all as specified and as directed.

S&F for 25mm bore Tubes medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors,complete all as specified and as directed.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete allas specified and as directed.

S& F for 15 mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and as directed.

S& F for 15mm bore Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed complete all as specified and as directed.

S&F 15mm dia pillar tap cast copper alloy chromium plated capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe fixed complete all as specified and as directed.

S&F for 15mm size PVC connection 450 mm long, with PTMT nuts complete all as specified and as directed.

S&F for 100mm dia grating doom PTMT (Min weight 25 grms),complete all as specified and as directed.

S& F for 15mm dia brass chromium plated shower rose 125 mm size and with or without swivel joints including fixing to pipe and union complete all as specified and as directed

S & F for Towel rail 600 mm long and 20 mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats complete all as specified and as directed.

S&F for CP waste fittings brass chromium plated for sink 32mm dia with long screws sinks and fly nuts , flange end bedded in red lead cement and other in fixed complete all as specified and as directed.

S&F for vitreous China squatting pan of pattern Orissa Pan , size 580 x440 mm white with integral foot rests any pattertn (excl flushing cistern and flush pipe) complete incl provn of lime concrete bedding connection to flush pipe , trap etc & making good complete all as specified and as directed.

S& F for Vitreous China wash hand basin, white, flat back, size 550mm x 400mm including brass coupling, mild steel brackets fixed to wall, complete all as specified and as directed.

S & F for Vitreous china urinal half stall type ,white including spreader connection to flushing pipe and outgoing pipe complete all as specified and as directed.

S&F for 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe of 32mm dia complete all as specified and as directed.

M&L for 32 mm bore low density polythelene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and directed.

S&F for 500 ltrs rotational moulded polythene water storage tanks( cylinder vertical with closed top) hoisted and fixed in position including ball brass valves,high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule as specified in SSR Part-I,complete all as specified and as directed.

S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high densitypolythene float ball and fly nut screwed for iron pipe complete all as specified and as directed.

S&F for 25mm dia gun metal,globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed,complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and as directed.

M&L for 75mm dia PTMT multi floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for PVC (SWR) gully trap 125 x 110 mm setting and jointing with solvent cement complete all as specified and as directed.

S&F for 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber rings ljoits fixed to walls complete all as specified and as directed.

S&F for 110 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed.

S&F for 75 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed.

M&L for 110mm dia PVC(SWR) Tee of with access door etc complete all as specified and as directed

S&F for 110 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and as directed.

S & F for 100 mm bore stack clamps out of 50mm x 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for etc complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment, confirming to IS 15658-2006of 60mm thickness M 35 Grade complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers ,apex stones, bed plates, water troughs and the like including use of formwork (straight or curved) ,including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed (Note :-reinforcement where provided shall be measured and paid seprately)

Excavation in trenches n exc 1.5m wide and exc 1.5m but n exc 3.0m in depth ;for foundation etc.or for shafts well cesspit,maholes, pier holes etc.n exc 10 sqm on plan area as in in soft /loose soil, complete all as specified and as directed

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate for foundation.filling and mass concrete complete all as speified and as directed.

M&L for broken bricks or brick bat loose filligs with aggregate of gauge 80 to 150mm in soakage pits,soakage well complete all as specified and as directed

M&L for Brickwork with fly ash bricks in one brick thick honey-comb walling, built in cement mortar 1:4 complete all as specified and as directed.

M&L for pre cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab set in CM 1:4,complete all as specified and as directed.

S&F for TMT bars 8mm dia cut cut to length bent to shape required including binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed

M&L for double wall corrugated (DWC) pipes 200 mm bore inner dia class class SN-8 confirming to IS-16098:2013 (Part-2) laid and jointed, with collars complete all as specified and as directed

M&L for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after the air laid and tested in Cement Concrete 1:3:6 type C2 for bore of pipes 200mm dia complete all as specified and directed.

M&L for Extra for forming fair finish for channel 30 cm inner girth in cement concrete using extra cement incl form, mould,mitred/stopped etc complete all as specified and as directed

Excavation over areas, n exc 1.5m deep and getting out in Soft/loose soil complete all as specified and as directed.

M & L for Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and lev- elled in layers n exc. 15 cm thick, watered and rolled/ rammed to a true surface complete all as specified and as directed.

M&L for brick work with kiln burnt bricks built in cm (1:4) using sub class 'B' bricks of compressive strength not less than 35 Kg/Sqcm straight or curved on plan exceeding 6 mtr mean radius with old size bricks complete all as specified and as directed.

M/L for 15mm thick rendering in CM 1:6 on fair faces of bricks or concrete surfaces finished fair and even complete all as specified and as directed.

M&L for 80 mm thick Machine pressed precast concrete interlocking paver block any shape and size confirming to IS - 15658-2006 of 80 mm thicknes M-40 Grade with pigment of any colour yellow/red complete all as specified and as directed.

M & L for providing, cement concrete type B-0 1:2:4 (using 12.50 mm graded stone aggregatet) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for 100 mm thick PCC 1:2:4 ,Type B2 ,using 40 mm graded stone aggregate as in paving /path finished fair and even complete all as specified and as directed.

M & L for excavation in post holes (or similar holes) each n. exc 0.5 cum, getting out in soft/loose, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

S&F for rolled section as in man and cross beam ,hip and jack rafters ,purlin where connected to common rafters and running rails and guides for sliding doors ;fixed for sliding ;fixed with angle cleats or other connecting plates complete all as specified and as directed.

M & L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe- 290 (Gde E-165) complete all as specified and as directed.

S & F for mild steel bolts exc 20 & n exc 25 mm dia, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and as directed.

S& F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

M & L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new or previously untreated surfaces of steel of any description, n.exc 10cm in width or girth including preparation complete all as specified and as directed.

M&L for Sub Main Wiring with two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 2.5 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 4.00 Sqmm Wire and One No of 4.0 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in Anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incl cutting, chasses and making good disturbed surface to match with existing finish with plaster for complete all as specified and as directed.

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ex fan controlled by one, one way switch 5 Amps

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 147 here in befor but with 1100 volts grade copper standard conductor cable of size 2.5Sqmm with 1.5Sqmm solid copper conductor PVC for 3 pin switch socket outlet15Amp independent board complete all as specified and as directed.

M&L for switch socket combination multipin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F for Switch Piano type single pole 5 amp, 230 Volts complete all as specified and as directed.

S & F for socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and as directed.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified and as directed.

Supply and fixing in replacement fan regulator modular step type capacity of polycarbonite complete all as specified and as directed.

Supply and fixing for Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet two nos bearings including connecting wire complete all as specified and as directed.

Supply & Fixing for Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), complete all as specified and as directed.

Supply & fix in replacement of LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified and as directed.

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suitable size & length complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply , laying and testsing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 2 core complete all as specified and as directed.

Supply and lay DWC pipe 38 OD and 63 mm including necessary excavation and return filling for cable protection complete all as specified and as directed.

Supplying and fixing,testing the water heater storage type 25 litres, BEE Five star Rated capacity and after connecting electric and water connection and screwing nuts and bolts , anchor hold fast to fixed on wall and making the good the disturbed surface, complete all as specified and as directed.

Hemant Associate (BID ID -3322463)

ANAMIKA CONSTRUCTION (BID ID -3322540)

chandra builders (BID ID -3321876)