S/E OF NEW STREET LIGHT AT CHOTTI NADDI TO VADDI NADDI SANOUR ROAD Est Cost Rs. 11.93 lacs dt 25/26.02.2026

Supply and Erection of Galvanized Steel Octagonal Pole (Sheet Thickness 3mm) with base plate designed to withstand wind speed 169 km/hour of suitable length Sheet Steel Confirming to IS 2062 : 2011 E350B0 (Yield Stress must be min 355Mpa and Tensile Strength min 470Mpa which is equivalent to BS-EN10025S355J or ASTM-572A GR-50) and thickness of Hot dip galvanization coating (70microns) conforming to IS:2629/ IS:2633/ IS:4759: BSEN-ISO-1461-1991 OR ASTM A 123/A123M-02. The pole shall be in single piece hot dip galvanized and shall be tapered towards the top. The bottom section shall have openable slot with exterior surface door & shall have suitable locking arrangement for housing three phase four wire cable connection, Bakelite sheet, MCB, loop in and out arrangement for incoming/ outgoing cables. There shall be suitable arrangement for earthing. Rigid Base plate of suitable size and thickness shall be welded inside and outside at the bottom of pole with provision for fixing 4 foundation bolts. The Octagonal Pole shall be bolted on pre- cast foundation with a set of four foundation bolts of EN-8 Grade with thread portion hot dip galvanized for greater rigidity. Galvanized Octagonal Pole Overall Length 6 metre (Sheet thickness 3mm), Top dia.(A/F) 70mm and bottom dia. (A/F) 130mm, 4 Nos. Bolts size 20mm dia., Length≥600mm with Base Plate Dimensions 220mm x 220mm x 12mm Thick

Supply and erection of bracket for galvanized octagonal pole, the bracket should be fixed on the top of the pole having top outer dia. 70mm to 90mm (A/F) complete in all respect as approved by the Engineer-in-charge at site:- Double arm bracket 1.5 metre long for galvanized octagonal pole

Triple Arm Bracket 1.5 metre Long for Steel Tubular Pole (7 to 8m)

Supply of Double Walled Corrugated (DWC) HDPE pipe of the required size:- Double Walled Corrugated HDPE Pipe 50/ 38mm (Outer/ Inner dia.)

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Overall size 16sq.mm (4Core) Un-armoured (Loose)

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1.5sq.mm (Un-sheathed)

Earthing with G.I. wire/ rope in G.I. pipe partly recessed and partly on surface complete with 150cm long 50mm dia. G.I. earth pipe (Cutting threads and 36 Nos. holes, 1cm dia. to make a mesh around the GI Pipe) with G.I. reducing socket including erection of the same, 4.50 metre (14.76 feet) below ground level with 20Kg. charcoal & salt mixture etc., up to 8 metre in length (including boring & refilling). Earthing with 8 S.W.G. (4mm dia.) G.I. wire in 15mm dia G.I. pipe with G.I. reducing socket 50mm x 15mm (upto 8Metre in length)

Earthing earth rod 20 mm dia for providing earth connections upto line earth with G.I. Wire 8 S.W.G. (4mm dia.). The rod shall be tapered at one end and flatted on other end. The hole size 10mm dia shall be drilled on the flatened side for facilitating connection with G.I. wire and thimble etc. The rod shall be erected in ground upto complete length vertically:- GI Earth rod 20 mm dia., 3 mtr. Long

Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- MCB Single Pole 6-32amp. (10kA, Curve-C)

S/E of LED Light 70 watt (including LED driver) with pressure die cast aluminium housing with control gear ( with IP 65/ IP 66 protection), CRI Minimum 70, CCT >5700K, toughened glass fitting, LED fixture minimum 120 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection (as per BIS standards) , surge protection 10kv and above (as per (IS/IEC standards) wattage of each LED High power LED of 1 watt to 5 watt with mandatory modular lenses, input AC frequency 50 Hz ± 3 % 5 year warranty including their drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter no AT-2021/GL 1410-1422 Dated 06/05/2021. Dated 06/05/2021. Besides this the lighting fixture manufactures should have in house NABL accredited labortary.

Galvanised iron wire at site of work 4mm.

Supply and erection of MS flat clamp 25mm x 5mm, 30cm long and 2nos. fastner 10mm x 75mm long with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site:-

Supply and erection of MS base plate in U shape for streetlight octagonal pole of 6mtr size 220 X 220 X 12mm with nut and bolts of suffiecient size and zinc coating complete in all respect as approved by the Engineer-in-charge at site:-