Repair and Maintenance of Dak Bungalow Building at Kalpeni

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately Second class teak wood 30 mm thick shutters

Providing and fixing karimaruthu wood or equivalent 25 mm squre wooden bars at required spacing in wooden frames of windows and clerestory windows

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness .The laminate shall be molded with fire resistant grade unsaturated polyester resin and chopped mat .Doorframe laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibreglass from all sides. MS stay shall be provided at the bottom to steady the frame

Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels confirming to TADS 6: 1993 and / or IS: 14856 - 2000 including fixing to frames

Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position

Providing and fixing at all height false ceiling of 4mm thick phenol bonded Bamboo Mat board (595x595mm) conforming to IS:13958- 1994 including providing and fixing of frame work made of GI angle 25x25x0.4 mm thick all around suitably fixed to wall with the help of dash fastener and hanger frame (600x600 c/c) made GI slotted Tee having powder coating on bottom side (30x25x0.3 mm thick for main member & 25x25x0.3 mm for cross member) connected to ceiling with 2.64mm GI wire and anchor fastener at every junction and also including cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed all complete as per direction of Engineer-in-charge

Providing and fixing 8 mm thick WPC (Luvars Panel ) board on wall and ceiling of approved quality with necessary nails/suitable screws etc. complete asper the direction of engineer in charge

Providing & fixing at all heights, levels and locations Mill finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).0.56 mm, Aluminium troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.

Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete :Precoated/mill finish aluminium Ridges plain (500- 600mm)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufactures specifications two or more coats applied on walls @1.25ltr/10 sqm) over including priming coat of special primer applied @ 0.75 ltr/10 sqm

Painting Wood work with Deluxe Multi surface paintto give an even shade.Two or more coats applied on @0.90ltr/10 sqm) over under coat of primer applied @ 0.75 ltr/10 sqm of approved and manufacture

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead :Cement mortar 1:4

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete (a)250 x10mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & anufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) nforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Khajariya matt finish vitrified ties/Jonson/Bell. (600 X1200) .

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & anufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :. White EWC pan with plastic seat and lid.

Providing and fixing white vitrous China wash basin with RS or CI brackets painted white, 15mm C.P bras pillar tap and C.P brass chain and rubber plug 32mm C,P. brass waste of standrad pattern 32mm diametre and waste pipe complete including cutting and making good the walls and floors where required. white vitrous china flat back wash basin 550x400mm with one 15mm C.P brass piller tap.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. .For External work.

(a ) 20 mm nominal outer dia .Pipes.

( b ) 32 mm nominal outer dia .Pipes.

( a ) 20 mm nominal outer dia .Pipes.

Providing and fixing CP brass bibcock of approved quality and manufacture complete.15 mm nominal bore

Providing and fixing CP brass stopcock of approved quality and manufacture complete. 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.15 mm

Providing and fixing CP brass Sink cock of approved quality and manufacture complete.20 mm

Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink asper IS 13983 with CI brackets stainless steel plug 40 mm ,including painting of fittings and brackets, cutting and making good the walls where required. Kitchen sink with drain board 510x1040x 250 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete..

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. (a)100x70x4mm(ordinary type)

b)75x65x4 mm (heavy type)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level ( 1 cement: 2 M.Sand: 4 granite chips 20 mm nomoinal size) foundation and plinth

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, shelves chajjas, lintel, bands, plain window sills, staircase and spiral staircase .. up to floor five level excluding cost of centring,shuttering and reinforcement . 1:1.5:3 (1 cement 1.5 M-sand 3 granite chipps 20mm nominal size

Reinforced cement concrete work in walls (any thickness), including attached ilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement . RCC 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Cement concrete block (machine moulded) masonry in Foundation and plinth in CM 1:6 with blocks of size 40cmx20cmx15cm.

Cement concrete block (machine moulded) masonry in Superstructure above plinth level in CM 1:6 with blocks of size 40cmx20cmx15cm

Steel work welded in built up section / framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer usin’g structural steel etc. as required. In grating, frames, guard bar, ladder, railings, racketgates and similar works.

Providing and fixing ceramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacture) of first quality confirming to IS:15622 of approved make, in colours such as White, ivory, Grey, Fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement: 4 M Sand) and including grouting the joints in spacer with white cement and matching pigment etc. complete. (Matt / Smooth finish)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to IS:15622 (thickness to be specified by the manufacture) of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer-in-charge in skirting,risers of steps and dado over 12mm thick cement mortar 1:3 (1 cement: 3 M Sand) and joining with grey cement slurry @3.3 kg per sqm, including grouting the joints in spacer pointing in white cement mixed with pigment of matching shade complete. 300x450 mm.

12mm cement plaster in C.M.1:6(1cement,6M.sand)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.0 mm thickness

Providing and fixing Bright finished brass door stoper with rubber cusion & necessary screws .

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per the direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing bright finished brass casement window fasteners or peg stays to windows/ ventilators with necessary welding and machine screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. 21.4.1 With stainless steel cover plate minimum 1.25 mm thicknes

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm

French spirit polishing: One or more coats on old work.

Providing and fixing health faucet of approved quality and manufacture complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and fixing nominal guage PVC Pipe of approved quality compleate with special flang compression type fitting s including trenching and refilling etc. External work (6kg/cm2)

a)110 mm nominal bore

b)75 mm nominal bore

c)63 mm nominal bore

d)32 mm nominal bore

e)25 mm nominal bore

Dislodging of septic tank including disposal of sludge by digging a pit within a lead of 50mtrs and covering it with sand including adding disifectants etc.including washing the tank and re-arranging of soak pit,man hole etc.complete as directed by the Engineer-in-charge.

Providing and fixing 18mm thick gang saw cut mirror polishe (premoulded and prepolished) machine cut for kitchen platforms, vanity countrers , window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar1:4( 1 cement: 4 P. sand) with jointed treared with white cement, mixed with matching pigment, epoxy toch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour & shade , area of slab over 0.50 Sqm.

Extra for Providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing PVC trap with gratings of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm PVC gratings with gullytrap.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. (

ProvidingandFixingPTMT towelrail with brackets fixed to wooden cleats with CP Brass screws with concealed ritting arrangement of approved quality and colour 600 mm long towel rail brackets with total length of 645 mm,width78mm and effective height of 88 mm ,weighing not less than 190 gms.

Providing and fixing toilet paper holderC.P. brass

Providing and fixing ball valve (PVC) of approved quality and manufacture complete. (a) 32 mm nominal bore.

Providing 40X3mm Iron hold fast 40cm long i/c fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding in cement concrete blocks of sizes 30x10x15cm of mix 1:3:6 ( 1 cement 3 M.sand 6 stone aggregate 20 mm nominal size)

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete 20 mm dia

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metre lead.For thickness of tiles above 10 mm and upto 25 mm

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer in charge. 1:4:8 or leaner mix

Demolishing brick work, manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable materialwithin 50 metres lead as per direction of Engineer-in-charge. In Cement mortar

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing and laying cement concrete 1: 4:8 ( 1 cement: 4 M.Sand: 8 granite chips ) foundation and plinth.Stone aggregate 40mm nomonal size

Centring and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform.

Centring and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centring and shuttering including strutting, propping etc. and removal of form for :Well steining

Cold twisted steel reinforcement for R.C.C. work including bending, binding and placing in position complete.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metre and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area beyond 3 sq. metres

Dismantling of flushing cistern of all types (C.I/PVC/Vitrious china) including stacking of useful materials near the site and disposal of unservicable materials within 50 metres lead as per direction of Engineer-in-Charge:

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 metres lead of: GS sheet

Painting Steel work with Deluxe Multi surface paintto give an even shade.Two or more coats applied on @0.90ltr/10 sqm) over under coat of primer applied @ 0.80 ltr/10 sqm of approved and manufacture

Earth work in excavation by manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 Sq.m on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.

Providing and fixing Bright finished brass Hydraulic door closer with necessary fittings &screws .

Providing and fixing bright finished brass handles with screws etc. complete:

Providing and fixing Flush door shutters confirming to IS:2202 (part.I) decorative type,teek wood planks construction frame.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws of first class teek wood with polished on both faces of shutters

Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS:3818 marked with necessary screw etc all complete

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-harge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing steel handle ( 304 grade ) with necessary screws

Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete Size 50 mm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats)

Providing and fixing fly proof Stainless Steel grade 316 wire gauge, to windows and Ventilators using wire gauge 0.50 mm dia. with average width of aperture 1.4 mm in both directions attached to powder coated aluminium frame frames including closing,lock

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg),including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of tiles 800x800 mm

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 120 cm girth upto and including 240 cm girth

Providing and fixing PVC pipe half round eaves gutter with M.S brackets including bolts and nuts and necessary fitting as per approved brand and manufacture etc ..complete 200 mm (10kg/sqcms)

Providing and placing on terrace at floor level) polythene water storage tankISI:12701 marked with cover and suitable locking arrangenebt and making necessary holes for inlet, outlet and over flow pipe but without fittings and the base support for tank.(a)500 Litre capacity. (Sintex/Ocean/Aquatech)

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)

Providing and fixing stainless steel ( Grade316) railing made of Hollow tubes,channels,plates etc... includingwelding grinding,buffing,polishing and making curvature( wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories & stainless steel dash fasteners,stainless steelbolts etc... of required size,on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc..)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections, but excluding modular plates etc..

Supply and fixing following sizes/ Modules, GI box along with Modular base and cover plate for modular switches in recess etc as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing 3pin, 5A cealing rose on the existing junction box/ wooden block including connections etc. as required.

Supply and fixing call bell /buzzer suitable for 230V complete as required

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-260 Volt, frequency 50/60 hz, (8w to10w)

Installation, testing and commissioning of wall brackets/ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting,, complete with all accessories, including connections etc required

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Dismantling of ceiling fan and painting with the same with one or more coats of spray painting with synthetic enamel paint of approved brand and manufacture to give an even shade, including cleaning of surface with detergent and replacing the damaged rubber reels, nuts and bolts with washers and safety pins, reinstalling the same as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Single Pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 214 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (Three phase and neutral), 415 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board vertical type, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 Way Double door

12 Way double door

Supplying and fixing following way, Three pole and neutral, sheet steel, MCB distribution board vertical type, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 Way (4+12) double door

8 way (4+18) Double door

Supplying and fixing of 25 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of GI box of following size modules, alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

Supply and drawing of UTP 4 pair Cat 6 LAN cable in the existing surface/recessed PVC conduit as required.

one run

Dismantling of unserviceable following electrical items including stacking with same as per engineer-in-charge

Tube light 40/20W

Ceiling fan / Exhaust fan

CFL / Bulk head

Wiring wire with conduit

Supplying of LED Tubelight set 20w 1800 lumen 4 feet

Supplying of PVC Bulkhead with Suitable LED bulb

LED lamp 7W/9W

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

32A DP Switch