ADDN AND ALTN TO BLDG NO C2 AND PROVN OF ROOM WITH TOILET HARDSTANDING AND COVERED SHED AT GARBAGE DISPOSAL FACILITY NEAR AHIRE OUTPOST AT NDA KHADAKWASLA

Amount

Dismantalling floor hearth and wall tiling and stone slab floor including cement mortar bedding but not backing complete all as specified

S&F 12 mm thick mineral fibre board ceiling tiles 600 x 600mm for accoustic purpose in ceiling in GI poweder coated snap grid frame with T and L section 600 x 600 fixed with 6mm GI wire suspended from roof slab/flat sections 40 x 3 mm size 60 mm long and expansion hold fasteneres 12.5 mm dia 40 mm long , 1200 mm centre to centre complete all as specified and as directed

S&F rolled steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates GDE Fe410-0 or Fe 310-O

M&L for two coats of synthetic enamel paint on steel surfaces of any description over 10cm width or grith including preparation of new surfaces and one coat of Red oxide primer

S&F frame work such as grills, gratings,hold fast etc, with ends of bars shouldered and or riveted, or forged into spikes; framed guard bars barred iron doors ladders framed balusers walk ways railing etc and similar work conforming to Fe.290Gde-E-165

M&L for 25mm thick PCC type B-1, (1:2:4) (Using 20mm graded stone aggregate) including preparation of surfaces complete all as directed.

M&L for vitrified tiles flooring 10mm thick (square/rectangular) polished laying in design pattern (Pattern approved by GE) area of each tiles not ecx 0.36 Sqm in floor etc laid bedded over 20mm thick CM (1:6) bedding & pointed in white/coloured cement to match coloured tiles etc complete all as directed.

M&L for vitrified tiles 10mm thick and 10 cm height as in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match tiles incl 10 mm thick backing plaster in CM (1:4) as specified and directed by Engineer-in-Charge

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 sqm but n. exc 0.11 sqm in floors etc set and jointed in neat cement sluury and pointed in coloured cement to match including 15mm thick screed bed of CM (1:6) bedding complete all as specified and directed by Enginner-in-Charge

M&L for ceramic tiles as in vertical surfaces of size 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed incl 10 mm thick backing plaster in CM (1:4) complete all as specified and directed by Engineer-in-Charge

M&L for coloured granite stone slabs as in door frame,window cill, jambs,20 to 16mm thick and laid bedded or and including 20mm thick in cement mortor (1:4) including bull nosing with brass 2mm thick strip in coloured cement matching with the coloured tiles complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters without taking off shutters from frame n exe 1.5 sqm each

S&F aluminium powder coated three track sliding window with 5.5 mm thick plain glass shutters and stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed (a) Bottom frame - 20620, (b) Top frame and vertical - 20621 (c) Handle (side) - 20606, (d) Shutter inter lock - 20724, (e) Shutter top & bottom - 20844 & (f) glazing clip -19352

S&F fully glazed door made up of plain/frosted glass, 12mm thick (design will be approved at the time of execution) secured at top and bottom rail with aluminium powder coated section supported and including 100mm hinges, brass door handles 300 mm size on both faces compmlete all as specified and directed by Engineer-in-Charge.Catalogues of Al membres of 'Jindal Make' are as under :- a) Door Top- 19528 b) Door Middle-19575 c)DoorBottom-19530 d) Door Vertical-19526 e)1"Handle- f) Glazing clip-19361or 19352

S&F powder coated aluminium partition with 5.5 mm thick plain glass with good quality rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed (a) Bottom frame - 20620, (b) Top frame and vertical - 20621 (c) glazing clip -19352

Cutting openings through walls built in CM for door, window & other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing & removing, shoring, cleaning & stacking stone and removing surplus to store & rubbish off the premises

Forming jambs, etc., to openings New work built in CM(1:6), including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete

Demolition of brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but including ashlar facings, dressed stonework & precast concrete articles

M&L for precast cement concrete block masonry with solid blocks type C1 (Using 20 mm grade stone aggregate) exc 10 cm in width and setting in cement mortar (1:6) complete all as directed and specified.

M&L for rendering 15mm thick cement plaster in CM( 1:6) on block walling surface finished even and smooth without using extra cement complete all as specified

M & L for preparation of new or old decorated surfaces of walls including concrete(plastered or un plastered) by brooming down and scraping wherever necessary and apply two coats of weather shield acrylic latex paint

S&F 1 mm thick mild steel sheet eaves gutters, galavinsed class 3, half round with rounded edges od dia 150mm complete allas specified and directed.

S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified and directed by Engineer -in-charge

S&F for 110mm dia PVC (SWR) bends any radius with access door complete all as specified and directed by Engineer -in-charge

S&F for 110mm dia PVC (SWR) junction single(single T) complete all as specified and directed by Engineer -in-charge

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer -in-charge

M&L for providing two way bib cock cast copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup (Make : Jaquar Cart Part No CAN-FLR -5041 N)

S&F Towel Ring of CP fixed with & including CP brass screws & wooden/plastic cleats (min. weight 90 gms)

M&L for cromium plated Soap dish Make: Jaguar cat No.QQT-7731

M&L for providing angular stop cock cast copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup (concealed type)

S&F CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S&F brass cromium plated Towel rack 24" all as pecified and directed

S&F hand shower (health faucet) Cat No ALD-573 and 1 mtr flexible tube with wall hook Make: Jaguar cat No.SHA-571

S&F wall mixer 3-in-1 System with provision for both teliphone shower and overhead shower complete with wall flange with 115 mm long bend pipe Make: Jaguar cat No. QQT-7281,SHA-571

S&F overhead rose shower Cat No. OHS-1709 and 450mm long swivel shower arm Make: Jaguar cat No.SHA-4792

S&F corner glass shelf 8 to 12 mm thick alongwith railing & fix with F bracket CP complete all as specified.

M&L for providing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plates brackets, guard and railing 60cm long all as directed by Engineer-in-Charge

S&F tubular towel rail 20mm dia 'D' type 60cm long of brass chromium plated complete all as specified

M&L for providing bib taps cast copper alloy chromium plated fancy type with crutch or butter fly handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia

S&F vitreous china wash basin, white, flat back, size 550x400mm with brackets, inc. cutting for & pinning in ends of brackets, inc. waste fitting, PTMT 32mm dia and pillar taps of PTMT 15mm dia complete.

S&F vitreous china wash down water closet pan (pedestal pattern), white, 'P' or 'S' type, inc. 10 litres, PVC flushing cistern, L L, white, with inlet,ball valve, float & brackets, inc. flush pipe, PVC tube 32mm dia. & inc. plastic water closet seat, black, closed pattern with flat bottem, & cover & M S CP or aluminium hinging device, complete.

S&F bathroom cabinet of size 450 mm X 300mm with door and shelves and mirror in front side of door and fixed to wall complete with washer

S & F 50mm PVC HDPE pipe fixed complete to wall or laid in floor with fittings etc complete all as specified .

S&F grating doom 125 mm dia with waste hole of PTMT. (min. weight 40 gms)

M&L for 75 mm dia PVC floor trap with grating including jointing with solvent cement concrete type B-1 (1:2:4) all as specified and directed by Engineer-in-Charge

M&L for cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintlesetc and cutting chases for concealed water tubing and making good cutting not exc 10 cm girth as in stone walls all as directed

S&F 15mm dia GI water tubing medium grade galvanised with all fittings & fixed complete to walls & ceilings or laid in floors.

S&F 20mm dia.GI water tubing 'medium grade' galvanised, with all fittings & fixed complete to walls & ceilings or laid in floors.

M&L for complete removal of existing treatment on wall and finshing the surface with 3 mm thick wall care putty and applying two coats of distemper oil emulsion.

M&L for surface preparation of newly plastered wall surfaces with primer and aplying two coat of oil bound Distemper complete all as specified

M&L for core cutting of upto 150mm dia, n.exc 600 mm depth in stone wall/conrete slab and making good disturbed surfaces andfd filling the remaining artea with cement concrete(1:2:4)type B1 (Using 20mm graded stone agg) complete all as specified and as directed.

S&F for aluminium anodised powder coated louver ventilator using rectangular tube of size 63.5x25x1.5mm along with 4mm thick design glass including provn of exast fan etc complete all as specified and directed by Engineer-in-charge . Note:- Exast fan will be paid separetaly

S&F coloured textured veniation blind (approx 1100 grm/3600mm) section with grooved, three side plain aluminium rod of 3600 mm with imported nylon operation unit (USA patent PC Taiwan Patent No 78712) with internal gear system and other imported special nylon combined with acrylic fittings with internal gear adjusting system and nylon chord with double hall chain and synthetic /Dolby Jacque red marooned 100mm fabric complete with other imported special quality component for extra mainatince free operations complete all as specified and directed

Excavating in trenches n.exc 1.5 mwide and not exc 1.5m deep for foundation etc and getting out in soft/disintegrated rock.

Ditto all as per item No 55 but for each additional 1.5m or part thereof in depth beyond the first 1.5 m in soft/disintegrated rock.

M&L for PCC (1:4:8) type D2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete including necessary use and waste of form work.

M&L for RCC (1:1½ :3) (Using 20mm graded stone agg) for foundation, including rafts, footings, fdn beams,plinth beams, bases for columns etc , basement slab , under reamed piles and mass concrete complete all as specified.

M&L for RCC (1:1½ :3) (Using 20mm graded stone agg) as in column /pillars, piers, posts and struts etc complete all as specified.

M&L for RCC (1:1½ :3) (Using 20mm graded stone agg) for beams, cantilevers, bressummers , lintels over 1.5m span etc complete all as specified.

M&L for RCC (1:1½ :3)(Using 20mm graded stone agg) for chajja complete all as specified.

M & L for reinforced cement concrete (1:1½ :3) (Using 20 mm grded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for use and wastage of form work to sides of concrete foundation, footings,plinth beams, bases of column etc for rough finished surface complete all as specified.

M&L for use and wastage of form work to sides of concrete pillars, post, struts, column etc for fair finished surface complete all as specified.

M&L for use and wastage of form work to beams, lintel etc for fair finished surface complete all as specified.

M&L for use and wastage of form work to chajja etc for fair finished surface complete all as specified.

M&L for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for 12 mm thick plaster on RCC roof slab with CM (1:4) including water proofing compound @ 3% by weight of cement shall be caried out as specified and directed by Engineer-in-charge (Note WPC shall be measured and paid separately)

M&L for preparing plastered surfaces,@ 0.25 Kg/Sqm with primer and applying water proofing treatment on roof walls, edges and vertical surfaces using APP modified memberane 3 mm thick with non woven polyster mat as reinforcement weighing not less than 3.50 kgs/Sqm complete over a coat of bituminous reflective aluminium paint complete all as specified. Note: Water proofing compound will measured and paid separately.

Supply only intergal water proofing compound

Damp proof course in cement concrete (1:2:4) type B0 25 mm thk to horizontal or vertical surfaces including necessary formwork

Returning, filling including, spreading, leveling, watering and well ramming in layers n.exc 25cm.

Removal of surplus soil to a distance n.exc 50mtr and deposited above directed at a level n.exc. 1.5 m where the starting point.

M&L for moorum filling in floors laid in layers not exc. 20 cm thick spread, leveled & rammed including watering (Moorum brought from outside MD Land)

M&L for hard core of gauge not exc 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of 100mm thick with broken/stone/boulers.

M & L for 100 mm thick cement concrete type C2 (1:3:6) (Using 40 mm gradded stone aggregate) as in plinth protection surfaces finished even & smooth without suing extra cement

M&L for rendering 12mm thick in CM (1:6) on fair faces of block wall or concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and as directed

M&L for preparation of newly plastered/concrete or block wall internal & external surface and applying two coats of cement base paint complete all as directed.

M&L for 3 mm thick wall care putty and applying two coats of distemper oil emulsion.

M&L for rendering 15mm thick in CM (1:4) including water proofing compound at 3% by weight of cement over 10mm thick plaster in CM (1:4) on block wall or concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separate.

M&L for non skid coloured ceramic tiles flooring 7mm to 8mm thick (square/rectangular) polished area of each tiles ecx 0.11 Sqm but not exc 0.18 Sqm in floor etc laid bedded over 15mm thick CM (1:6) bedding & pointed in white/coloured cement to match coloured tiles etc complete.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft / loose soil

M&L for mild steel rolled section connected with each other with welding (angle,tee,channel, beam, hollow sections etc) as in main and cross beams, hip,verticle hollow sections and jack rafters, purlins where connected to common rafters and running rails where verticle sections are fixed in welded in wallsin wall surface with plates & other verticle sections are fixed in ground level embedded in concrete fixed and horizontal sections fixed in wall with bolt completly, fixed with angle cleats or other connecting plates conforming to GdeFe-410- W(Gde- E-250) quality- B complete all as specified and directed by Engineer in charge.

M&L for roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc GdeFe-410- W(Gde- E-250) quality- B complete all as directed.

S&F for pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering fixed with J-type or L-type or cranked hook bolts drilled with the screws and fixed in horizontal or verticle sections complete all as specified and directed by Engg In charge.(Design and pattern will be approved by GE.)

S&F for pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in as in curved or straight roof covering fixed with J-type or L-type or cranked hook bolts complete all as specified and directed by Engineer in charge

M&L plates (plain or chequered) channels Fe 410 -W (Gde- E- 250) quality- A-square cut or notched (ordinary and counter sunk) forming holes or weleded to section for supporting the truss with inter welded to each other all as specified and directed by Engineer In charge.

M&L for anodised aluminium snap grid frame work for false ceiling all as specified - Size of grid 605 x 605mm - S & F

M&L for non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws - 4mm thick complete all as directed.

M&L for providing angular stop cock cast copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup complete all as directed. (Make :Jauqar & equal)

Vitreous China urinals,half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2),securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe (excluding flushing cistern, flush pipe and waste pipe) urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) including all fitting.

S&F fibre reinforced PVC connecting pipe 60 cm long with brass check nuts and washer both side

S&F for CI floor trap with PVC grating 75mm dia including jointing to waste pipe fixed in cement concrete type 'B' (1:2:4).

S&F unplasticised PVC pipes if pressure rating 10kgf/cm fixed complete to wall, ceiling or in floor etc., pipe size 15mm complete all as specified and directed by Engineer In Charge.

S&F unplasticised PVC pipes if pressure rating 10kgf/cm fixed complete to wall, ceiling or in floor etc., pipe size 20mm complete all as specified and directed by Engineer In Charge.

M&L for pressed steel frames 105x60mm for doors with one or more rebates incl necessary fixing lugs , hinges, lock strike plate ,etc complete as specified supplied and fixed.complete all as directed.

Supply and fix 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match and other face commercial type including all side lipping wooden fillet wrougnt and fixed to wooden/ steel chowkets all as specified and directed by Engineer-in-Charge.

S&F for 0.9mm thich decorative laminate type I, of surface finish, colour and pattern as approved , fixed with approved adhesive as per maker's instructions

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification all as directed

M&L for factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement all as per specification and as directed by Engineer-In-Charge.

S&F aluminium barrel tower bolt of extruded section and fixed complete length of bolt 200 mm

S&F 250 mm long aluminium sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding boltsof extruded sections all as specified and directed

S&F butt hinges, medium weight, cold rolled, mild steel length of hinges 100 mm

S&F extruded aluminium alloy handle fabricated type annodised size of handle 100 mm

M&L for gun metal gate or globe valve 20mm with iron wheel head ,screwed both ends for iron pipe

M&L for rotational moulded polyethylene water storage 1000 litres tank (cylindrical vertical with closed top) hoisted and fixed in position and Including 20 mm dia stop cock cast copper alloy and 20 mm dia PTMT float valves complete all as specified in SSR part I

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard dence soil

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil.

M & L for cement concrete type D- 2, (1:4:8) (Using 40mm graded stone aggregate) - 100mm thick

M&L for cement concrete type B- 2, (1:2:4) (Using 40mm graded stone aggregate) - 100mm thick

M&L for PCC(1:2:4) type B-1 (20 mm graded aggregate) 40mm thick as in floor with even and smooth finishing without using extra cement complete.

M&L for cement precast cement concrete block masonry with solid blocks,type B1, (1:2:4) using 20 mm graded aggregate exc. 10 cm in width and setting in mortar (1:4), complete

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces - Cement plaster 1:4 to be finished even and smooth without using extra cement.

M & L for concealed Point wiring with 1.5 Sqmm (nominal cross-sectional area) FRLSH PVC insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non-metallic rigid PVC conduit ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including modular cover plate with frame and PVC box suitable for modular type switches, sockets, fan regulator etc for following :- One light/Fan point controlled by one way switch 6 Amps 240 volts

Ditto all per item No. 115 above but one 3 pin socket outlet, 5 Amps on the same board

Ditto all per item No.115 above but one 3 pin 6 Amps socket out let point on independent board.

M&L for concealed point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC conduit type ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket outlet power point independent circuit

S & F energy efficient BEE five star rated storage type water heater vertical mounted of capacity 25 ltrs including fixing the geyser with necessary fastner arrangement as per the site requirement complete all as specified and directed. Make: Racold/Havells.

S&F GI mesh flexi connection pipes 15 mm dia suitable for hot & cold water not less than 450 mm long with brass metallic flexi nuts on both ends of pipe.

M&L Sub main wiring with PVC insulated FRLS grade cable LT 1100 Volts grade PVC insulated unsheathed, multistranded with stranded copper conductor drawn through & including surface type PVC conduit including drawn on wall accessories alongwith one contineous earth wire and connected to common earth complete all as specified for following sizes of cable. 2 x 4 sq mm with one contineous earth wire of size 4.0 sq mm Note : 2 runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

M&L modular switch 6 amps one way, 1 module

M&L modular socket 6A-2/3 pin , 2 module

M&L modular switch 1 way 16A 1 module.Make : Vnay/Roma

M&L Modular socket 16A 2/3 Pin 2 Module. Make:Vinay/Roma

S&F in replacement modular step type fan regulator 120W, 2 module Make- Vinay/Anchor Roma

M&L in replacement recess mounted edgelit slim LED panel square powder coated PDC aluminium body and high quality LGP & PMMA user, separate driver 15 watt, 3500 K 240 volts environmental friendly, new generation, energy saving including connecting with twin core wire including cutting the false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully all as specified and directed. Make: Havells/Polycab/Philips. Note: The quoted price shall include the coat of light and its driver.

S&F 10Watt warm white LED batten suitable for indoor application of color temperature 6500K including connecting with twin core flexible wire of size 1.0Sqmm all as specified. complete all as specified and directed Make:Philips/Wipro/Luker.

Supply and fix in replacement sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as directed by Engr-in-charge. Make: Legrand Cat part: 5078 10 or equivalent in C&S/L&T

S&F in replacement MCB DB 08 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engineer-in-charge. Make: Havells/Legrand. Note: MCBs with be measured & paid separately under respective item of sch A if required to be replaced.

Supply and fix MCB single pole 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed. Make: Legrand/Indo Asian/L&T

Supply and fix MCB SPN 6-40 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve all as specified and directed. Make: Legrand/Indo Asian/L&T

S&F ceiling rose, surfaces shall comply with IS: 371-1979 bakelite 60x25 mm two to three terminals plates and outside diameter not less than 63.5 mm

M&L for exhaust fan of sweep 225/230mm,metal body single phase 240volts, and making hole by core cutting as per the required size of the exhuast fan and making good the disturbed surfaces and fixing to the wall with proper fasetner arrangements and all accessories.

S&F ceiling fan of sweep 1200mm,240volts, of not less than 5 star BEE rating milky white coloured connecting up with twin core 1.0 Sqmm cable from ceiling rose including required length of MS hanging rod all as specified.Make:Orient/Havells/Crompton Greaves.

Supply and installed Air cooler star rated split AC indoor & outdoor units complete alongwith cordless remote control and outer unit holding MS angle iron frames suitable for outdoor unit including in built Air ioniser and plasma filter for better indoor Air quility of capacity 1.5 TR. Make: Hitachi/LG/Diakin.

Supply and fixing only for Auto voltage stabilizer single phase naturally Air cooler indoor type & designed for input with time delay system of input 160 to 275 volt and output 200 to 240 volt, +/-2% variation 240 volt capacity 5 KVA Make: Venus/LG/V-Guard.

J.G.Goel

Sarkar Enterprises

agarwal and company