PROVN OF ONE X DEFICFIENT SINGLE JCO LIVING ACCN FOR JCO POSTED WITH 431 (I) SUP PL ASC AT FATEHGARH

Amount

M&L for surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

Excavating over areas n.exc. 1.5 m deep for foundation and getting out in soft / loose soil complete all as specified and directed.

Excavation over areas, exc. 1.5 m but not exc. 3 mtr depth for footing in soft / loose soil etc complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 as in foundation filling and mass concrete etc complete all as specified and directed.

Returning, filling in including spreading, levelling and well ramming, in layers not exc. 25 cm each layer of any type of soil complete all as specified and directed.

Removal of surplus excavated soil to a distance n.exc. 50 m and despoisted where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

M&L for RCC M-25 design mix as in foundation including rafts, footings, foundation beams, plinth beams, bases for collumns etc basement slabs under reamed piles and mass concrete etc complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, side and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter etc complete all as specified and directed.

M&L for mild steel TMT Fe 500D bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending sprially for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M&L for mild steel TMT Fe 500D bars 5 mm dia and over upto and including 10 mm dai in stirrups, spacers and binders etc complete all as specified and directed.

M&L for RCC M-25 design mix as in columns, pillars, posts and struts etc complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchionsa complete all as specified and directed.

M&L for brick work with sub class 'b' bricks old size straight or curved on plan exc. 6 m mean radius built in cementt mortar (1:6) complete all as specified and directed.

M&L for brick work with using old size sub class 'B' bricks straight or curved on plan exc. 6 m mean radius in half brick thick wall built in cement mortar (1:4) complete all as specified and directed.

M&L for RCC M-25 design mix in chajjas and the like etc complete all as specified and directed.

M&L for RCC M-25 design mix as in beams, cantilevers, bressummers, lintels over 1.5 m span etc complete all as specified and directed.

M&L for form work as in roof beams etc complete all as specified and directed.

M&L for RCC M-25 design mix for slabs supported on walls, beams and columns in floors, roofs, landings, balconies canopies deck slabs and in shelves and complete all as specified and directed.

M&L for form work to soffits of suspended slabs such s roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping) etc complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on brick or concrte surfaces fair finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) on fair faces on ceiling concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces fair finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and appyling two coats of 100% premium acrylic emulsion paint / plastic emulsion paint having VOC less than 50 gm / litre over a coat of 1 mm thick wall care putty on wall surface complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for applying two coat of weather proof paint (external surface of wall, parapets, sides and tops of sunshades) over a coat of weather proof putty complete all as specified and directed.

M&L for 75 mm thck cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate) for sub base of flooring or lean concrete complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 including forming joints 10 mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and directed. Note :- The quoted rates are deemed to be inclusive of material against form work and joint fillings)

M&L for hardcore of gauge n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface (broken stones / boulders) etc complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8-10 mm thick (square / rectangular) polished, area of exceeding 0.36 sqm but not exceeding 0.42 sqm in floors etc set and jointed in near cement slurry and pointed in tile grout / white cement / coloured cement including screed bed or bedding layers of mortar 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed.

M&L for double charged vitrified ceramic tiles 8-10 mm thick (square / rectangular) polished, area of exceeding 0.36 sqm but not exceeding 0.42 sqm in floors etc set and jointed in near cement slurry and pointed in tile grout / white cement / coloured cement including 10 mm thik plaster in CM (1:4) for skirting / dado etc complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for non skid mat finished coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for glazed coloured ceramic tiles in vertical surfaces 450 mm x 300 mm x 7 mm thick (pattern / digital tiles) set and jointed in neat cement slurry and pointed in white or colour cement to match over plastering 10 mm thick on fair faces of brick work or concrte surfaces in CM (1:4) to receive wall finishes complete all as specified and directed.

M&L for preparation of newly plastered surfaces of roof including cleaning the surface by using wire brush / pressure hose and applying high performance polyurethane liquid membrane roof casting cold in two coats @ 1.5 kg / sqm with spray / brush as elogation of 300% to 700% and tensile strength not less than 3 N/Sqm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5 mm as per ASTM C 1305, shore a hardness of not less than 60 as ASTMD 2240. The item includes epoxy prime applied @ 0.15 kg/sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacturer's instrucction and sond engineering practice complete all as specified and directed. Note :- Work shall be execcuted by authorized applicator of manufacture as per manufacturer's instruction and roof height upto double storey building.

M&L for steel water tubing 15 mm bore with screwed & socket joints, medium grade galvanized (including short length) with and including all necessary fittings, such as sockets bends, elbow, unions, tees, diminishing pieces etc fixed to walls or ceiling or laid in floors complete all as specified and directed.

M&L for steel water tubing 20 mm bore with screwed & socket joints, medium grade galvanized (including short length) with and including all necessary fittings, such as sockets bends, elbow, unions, tees, diminishing pieces etc fixed to walls or ceiling or laid in floors complete all as specified and directed.

M&L for bib tap, fancy type, chromium plated long body cast copper alloy ISI marked with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore pipe and fixed (weight of one bib tap shall not less than 400 gm each) complete all as specified and directed.

S&F gun metal gate valves with rion wheel head, screwed both ends suitable for 20 mm bore GI pipe complete all as specified and directed.

M&L for stop valve / angle cock, 15 mm bore, fancy type, cast copper alloy chromium plated, screwed down high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F brass CP wall mixex with L bend for fixing hot & cold water screwed down for iron pipe and fixed to 15 mm bore pipe complete all as specified and directed.

M&L for PVC connection 15 mm dia and 450 mm long with PTMT nuts at both ends complete all as specified and directed.

S&F for vitreous china wash down water closet pan (pedestal pattern) white (including fixing bolts, PVC (SWR) 'P' trap and flush pipe) including all necessary accessories like rag bolts / get gasket, white seat cover etc complete all as specified and directed.

S&F for PVC valve less, syphonc action type, flushing cistern of capacity 10 litres, low level, white, with inlet, ball valve, float and handle including brackets & all necessary accessories complete all as specified and directed.

S&F for vitreous china oval type counter top wash basin, white, size 550 x 400 mm including 32 mm PVC waste pipe, 32 mm PTMT waste coupling and 15 mm dia pillar taps fancy type cast copper alloy chromium plasted complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks double layer with ISI mark engraved on tank body 500 ltr capacity (cylindrical vertical with closed threaded top) hoisted and fixed in position including 20 mm dia PTMT Float valve complete all as specified and directed.

S&F for health faucet mild steel chromium plasted suitable for 15 mm dia pipe with 1.25 m long flexible tube and wall hook including making connections and fixed in position complete all as specified and directed.

S&F for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F soap dish, any type fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F brass chormium plated, tubular towel rail, 20 mm dia, D type 60 cm long between flanges complete all as specified and directed.

S&F brass chromium plated shower rose 125 mm dia including fixing with swivel shower arm for fixing with 15 mm pipe (minimum weight 40 gms) complete all as specified and directed.

S&F for rolled sections as in framing for cladding glazing frame / chowkhat and the like with angle cleats and connecting plates etc conforming to Fe 415-W (Gde E-165) quality A complete all as specified and directed.

S&F for 30 mm thick flush shutter of second class hard wood complete all as specified and directed.

S&F for anodized aluminium window and ventilator shutters, side hung type without sash bar, aluminium sections weighing 0.55 kg /m including necessary jointing cleats, glaing clips, rubber packing anodized aluminium snap beading, tower bolts (4 Nos), screws anodized aluminium fitting such as peg stays 150 mm long (01 No) hinges type B-21, 100 mm long (2 Nos) suitable handle (2 Nos) in each window complete all as specified and directed.

S&F for anodized aluminium grill (anodized transparent on dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15 of approved design / pattern with approved standard section and fixed to the existing window frame with CP bras / stainless steel screw @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section aground the opening complete all as specified and directed.

S&F for powder coated anodized aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for 5.5 mm thick sheet glass, ordinary quality and glazing with oil / silicon putty in square n.exc. 0.5 sqm in each pane complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed.

M&L for preparing new surfaces of wood and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F for sinks made of stainless steel 01 mm thick kitchen or laboratory with plugs washers and wastes pipe including bedding in cement mortar or to dwarf wall or including fixing cantiliever brackets and connecting union to pipe over all size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed

S&F for solid PVC door frame of size 50 mm x 47 m made out of 5 mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specifiction and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock and bottom rail on either side & as gap insert for top rail and bottam rails, paneling of plain colour PVC sheet to be fitted in the MS frame welded / seated to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specifiction and drawing. complete all as specified and directed.

S&F for mild steel butt hinges cold rolled of size 100 mm medium weight complete all as specified and directed.

S&F for aluminium anodized barrel twoer bolts of extruded section of 125 mm size etc complete all as specified and directed.

S&F for aluminium handles, cast type anodized of size 125 mm etc complete all as specified and directed.

S&F in 300 mm long aluminium anodized, sliding door botl with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sectin and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M&L for 75 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F for PVC (SWR) pipe 75 mm dia single socketed in any length with rubber rig joints, fixed to wall or laid in floor complete all as specified and directed.

S&F for PVC (SWR) pipe 110 mm dia single socketed in any length with rubber rig joints, fixed to wall or laid in floor complete all as specified and directed.

S&F for PVC (SWR) bend 75 mm complete all as specified and directed.

S&F for PVC (SWR) bend 110 mm complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm setting and jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size / shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver block into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm grade stone agg) as in kerb stone / coping etc complete all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n.exc. 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n. exc. 10 sqm on plan and n.exc. 1.5 m in depth and getting out in soft / loose soil complete all as specified and direccted.

M&L for concrete bed width (outer diameter of drain pipe plus 300 mm) and thick 150 mm in 1:3:6 type C-2 for 200 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for providing precast cement concrete 1:2;4, type B-1 (using 20 mm graded stone aggregate) as in landing, cover slabs, (for man holes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in mortar 1:4 complete with joints to match complete all as specified and directed.

M&L for PCC bed in PCC (1:3:6) (using 40 mm graded stone aggregate) as in surface channel of drain including providing necessary form work complete all as specified and directed.

M&L for extra forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

Supply and laying pipe in trenches or fixed on wall / floor, galvanized iron "Medium class" including all fittings size 25 mm dia complete all as specified and directed.

Supply and fixing for 20 mm bore galvanized steel tubing, medium grade with all fittings and fixed to wall, ceilings or laid in floor complete all as specified and directed.

M&L for cutting existing GI pipe line of 25 mm dia for insertion of tee of suitable size for branch connection including excavation and earth work complete all as specified and directed.

M&L for screwing existingg steel tubing of 25 mm dia for alterations or additions ( or lengthening screw on pipe to form connector) complete all as specified and directed.

M&L for concealed point wiring for one light point / fan point / bell point controlled by one switch (using red, black and green etc colour wire as colour coding coplete with 1.5 sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volts (ISI marked) drawn through and including PVC conduit 20 mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc including pressed steel powder coated sunken modular terminal box (min 60 mm deep, suitable size) concealed in wall, flush to surface for mounting of switches / socket regulator etc including provn of 1.5 sqmm single core FRLSH PVC insulated multri strand copper conductor wire continues as earth wire connected to earth dolly etc including cutting chases in wall and making good distrubed surface of wall / ceiling / floor etc by using CM (1:3) complete all as specified and directed. Note- Switch, socket, regulator & (inner & outer) cover plate with frame of different moduly of required colour should be measured and paid separately)

All as per item No.84 above but for one 6 Amp socket on an independent board complete all as specified and directed..

All as per item No.84 above but for one 6 Amp socket point on same board complete all as specified and directed.

All as per item No.84 above but for one 16 Amp socket point on an independent board with 2.5 sqmm (FRLSH) unsheathed conductor single core multistranded complete all as specified and directed.

S&F modular switch 1 way 6 A, 1 module complete all as specified and directed.

S&F modular socket 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F modular switch 1 way, 16 A, 1 module complete all as specified and directed.

S&F socket modular 16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F white cover plate (inner & outer) with frame 1 module complete all as specified and directed.

S&F white cover plate (inner & outer) with frame 3 module complete all as specified and directed.

S&F white cover plate (inner & outer) with frame 6 module complete all as specified and directed.

S&F modular bell push, 6 Amp, 1 module complete all as specified and directed.

S&F bell ding dong AC 230 volts, single pole complete all as specified and directed.

S&F modular electronic fan step regulator, 120 W - 2 module complete all as specified and directed.

S&F ceiling rose PVC / poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for sub main wiring with two single core 6 sqmm FRLSH copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 sqmm FRLSH insulated multi stranded unsheathed copper conductor used as a earth wire to common earth the connection to earth dolly complete all as specified and directed. Note :- Two run of 6 sqmm FRLSH and one run of 6 sqmm FRLSH copper conductor shall be measured as one unit length.

Supply and fixing of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with copper thimbles as required complete all as specified and directed.

S&F of MCB SPN 63 Amp 240 volt 'C' curve 10 KA complete all as specifed and directed.

S&F of MCB SP 10 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and directed.

Supply and fixing LED lights fitting 4 ft, 20 W, 220 V, AC batten type including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Suply and fixing LED lights fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 V AC batten type including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED decorative wall light fixtures made up of polycarbonate, suitable for 09 W TU retrofit CFL (B-22 base) including LED bulb 09 watt of colour temp 3000 K & luminaire lumen > 1000 lm complete all as specified and directed.

S&F building security LED light 30 watt made up pressure die-cast aluminium housing with high power LED as lighting source and lesn embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building security purpose with bracket size made of GI pipe medium grade 25 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS clamp of size 25 x 6 mm for fixing of building security light fittings completed all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F of exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz RPM 1200, copper winding of sweep 250 mm including complete fitting into the wall complete all as specified and directed.

Supply, fix and connect and test stroage water heater (Geyser) vertical type, mounting type 25 litre capacity with glass lined steel tank, shock resistant ABS outer body, swirl flow technology with copper heatig element 2000 watt capacity and all specification as per BEE 5 star rating including all connected accessories such as safety valve, thermostat multifunction LED indicator, PVC inlet / outlet hot & cold connection pipes, NRV etc complete all as specified and directed.

S&F of metal plug & socket DB with metal plug and MCB single pole enclosure with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire of size 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, HT/LT equipments, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply and laying cable XLPE insulated screened PVC bedded, galvanizedsteel strip armoured service cable pole to building electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core complete all as specified and directed.

Supply and laying cable XLPE insulated screened PVC bedded, galvanizedsteel strip armoured service cable pole to building electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed.

S&F of DWC high denisty polyethelence pies having dia 63 mm / 50 mm, inner as per site requirement havingcorrugation on the outer wall and plain surface on the inner wall conforming to IS : 14930 (Part-I&II) for protection of undergrund cable laid along pole /along wall / in PCC on GL / roof and including as required at site complete all as specified and directed.

Fabrication, supply, installation testing and commissioning electrical cubical control panel board (KIOSK TYPE) of size 600 x 450 x 550 mm double door, CPRI approved as ISO 9001 factory assembled made out pedestal type feeder pillar box wheather and vermin proof fabricated of 3 mm CRCA MS sheet of suitable size, 3 phase, 4 wire, 415 volt AC 52 Hz complete duly painted with powder coating complete with locking arrangement, earthing terminals with suitable rating aluminium strips for incoming / outgoing MCCB's including incoming and outgoing cbales connections with suitable cable glands and end termination including grouting of feeder pillar box 60 cm above ground level by providing 105 cm long angle iron size 50 x 50 6 mm welded on all four courner embedded in PCC (1:2:4) using 20 mm graded upto 45 cm complete all as specified and directed by Engr in charge . (Feeder pillar box shall be consisting the following) (a) 4 Nos electrolytic aluminium bus bars high conductivity alloy proper insulated of 1 1/2 time of the incoming capacity with provision of extension and mounting on porcelain support (b) MCCB 100 amps, 25 KA, 415 volts, 50 Hz - 01 No (incoming) (c) 08 Nos, holes in bottom for inlet and outlet cable with suitable size of cable gland (d) Electric connection between MCCB and busbar shall be with aluminium strip links duly colour coded. (e) RYB indicating lamp, LED type - 01 Sets Note :- Cost of PCC for foundation is deemed to be included in quoted rate by the contractor. Drawing shall be approved by AGE (I) before planning in order.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, burried directly into the ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI earth strip of size 32 x 6 mm dia by means of bolts, nuts, check nuts, and washers of galvanised iron or steel all as shown in electrical plate No - 3 connected to earthing test point all as specified or indicated including excavation and connected earth work, PCC chamber and cover, watering pipe, funnel wire mesh but without earth lead protection pipe and test on completion after dismantling unserviceable erthing (above GL only) complete all as directed incl dismantling of exsisting earthing. (Note :- On testing after completion if desired earth resistence is not obtained, the earthing will be redone at no extra cost.)

GEESR INFRA BUILDERS PVT LTD (BID ID -3509561)