SPL REPAIR TO TOILETS OF DHOBI GHAT AND PROVN OF MANGERS AT OPEN STANDING OF BOTH LARGE ANIMAL WARDS AT 45 MIL VET HOSPITAL AT NDA KHADDAKWASLA

Amount

Taking down wooden/steel/pvc chowkats or frames exc 1.5 Sqm and n. exc 4 Sqm each

Taking down wooden/steel/pvc chowkats with shutters (w/o taking off shutter from frame) exc 1.5 Sqm and n. exc 4 Sqm each

S&F 100% Solid wood plastic composite (WPC) Door Frame manufactured by M/s Giza of size 90mm x 45mm made from wood plastic composite (single extruded process) mateial with density 780kg/cum & manufactured by NAVRATAN SPECIALTY CHEMICAL, Ahamedabad (Gujrat) an ISO 9001-2015 certified company or equivalent specifications manufacturer as approved in zonal speciations and E-in-C. The door frame shall be fixed to the wall using 65/100mm long M.S. Screws through the frame by using PVC fasteners. A minimum 04 Nos of screws to be provided for each vertical member & 02 Nos for horizontal members etc. complete all as per manufactures specification and as directed by Engr-In- Charge.

S&F 100% Solid PVC flush shutter 28mm thick, made rigid wpc plain/prelaminated door shutter , made from co-extruded three layer rigid PVC foam sheet (single extruded) with density not less than 600 kg/cum, outer layer 1mm thick should be of rigid PVC with density of not less than 1400 kg/cum manufactured by NAVRATAN SPECIALTY CHEMICAL, Ahamedabad (Gujrat) an ISO 9001-2015 certified company or equivalent specifications manufacturer as approved in zonal speciations and E-in-C. Fixing the shutter to frame with hinges, etc complete all as per manufactures specification and as directed by Engr-In- Charge.

Refixing of shutters in same opening by resecuring or easing & adusting (while taking down of frame in under above item no 1 above and refixing after fixing of new frame) of any description exc 1 Sqm and n. exc 2 Sqm each etc all as specified and directed by Engr-In- Charge.

M&L Aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long

M&L Aluminium alloy anodised sliding door bolt with hasp staples (bolt type and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section a cast aluminium alloy and fixed 250 mm long for use of padlock

M&L 100mm long butt hinges cold rolled mild steel medium weight and fixed

M&L Extruded aluminium alloy handles, fabricated type, anodised 150mm long

Demolition of brick/ block masonry built in Cement mortar

M&L for cement concrete 1:4:8 type D2 (40 mm graded aggregate) as in mass concrete and foundation etc

M&L PCC precast cement contrete solid block masonary exc 10cm in width in PCC type C1,1:3:6 ( using 20 mm stone aggregate) and set in cm 1:6 all as specified.

M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius , built it old size bricks in cement morter 1:6 complete

Taking down cement plaster on brick/block or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L Rendering 15mm thick on fair faces of brick/block work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement

M&L plastering 15 mm thick in CM 1:6 finising even & smooth without using extra cement on wall .

M&L plastering 10mm thick in CM 1:3 finising even & smooth without using extra cement on ceiling .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L non skid/ ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 sqm but n. exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:6) bedding all as specified and directed by Engineer-in-Charge

M&L glazed ceramic tiles as in vertical surfaces of size 450 x 350 x 7mm/450 x 300 x 7mmthick set and jointed in neat cement slurry/paste and pointed in coloured cement to match designed incl 10 mm thick backing plaster in CM (1:4) as specified and directed by Engineer-in-Charge

M&L prepartion of old surfaces of ceiling and applyiing one coat of white wash all as specified and directed

As item no 21 above but three coat of white wash on new surface

M&L prepartion of old surfaces of wall and applyiing one coat of white wash all as specified and directed

As item no 23 above but two coat of white wash on new surface

M&L preparation of newly plastered surfaces and applying two coat of cement base paint over a coat of alkali resistant primer as directed

Taking down up or down steel tubing and connections 15mm dia pipes.

Taking down up or down steel tubing and connections 20mm dia pipes.

M&L Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 15mm bore of pipes .

M&L GI tubes medium grade galvanised with all fittings fixed complete to wall and ceiling or laid in floors of 20mm dia of pipe.

S&F in repair Stop valves fancy type Chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed 15mm bore of pipe

S&F in repairs fancy type Bib taps 15mm dia Chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including taking down old one complete all as specified and directed.

S&F for in repairs Fancy type Pillar taps 15mm dia, cast copper alloy, with capstan heads, chromium plated , screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe

S&F vitreous China wash basin white, flat back size 550 x 400mm with necessary brackets including fixing of chromium plated CP waste coupling, chain and plug, waste fitting, union and waste pipe 32mm dia of required length and all necessary 450mm long outlet and inlet PVC connections pipes with PTMT check nuts complete.

M&L Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 50mm bore of pipes

S&F Watercloset (squatt pattern ) orissa pattern 630 X 450 mm complete including provision of lime concrete bedding incl of necessary traps

S&F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia,for low level cistern

S&F PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet ball valve float and handle including brackets

S&F vitreous china urinal bowl type (back or corner wall type ) of size 465 x 355 x 265mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with discharge pipe etc complete all as specified and as directed by Engineer In Charge.

S&F Urinal spreader of PTMT any colour for fixing with 15mm dia pipe

Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 150 mm dia.

M&L for 200mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars for draining water laid under floor as specified & directed by Engineer in Charge

M/L for providing bed to drain pipes 200 mm dia in cement concrete (1:3:6) type C2 using 40mm graded stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested.

M&L for PCC 1:3:6 type C2 as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for CI pipe 150mm bore.

S&F 150mm RCC Hume pipe class NP2 laid and jointed complete with collars

M/L for providing plain cement concrete 1:2:4 type B1 using 20mm grade agg. as in surfaces channels & drains

Dismantling of cast iron/pvc 100 mm bore pipes jointed in cement motar including all fittings

M&L for PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors 110 dia fixed in repair.

All as per Item No. 47 above but 75mm dia fixed in repair

M&L PVC (SWR) pipes single socketed in any length with rafter joints fixed wall 110mm dia fixed in repair

All as per Item No. 49 above but 75mm dia fixed in repair

M&L for PVC (SWR) bends any radius of 110mm dia with access door

M&L for PVC (SWR) bends any radius of 110mm dia without access door

All as per Item No. 52 above but 75mm dia without access door

All as per Item No. 53 above but 75mm dia with access door

M&L for PVC (SWR) junction single (single T ) equal or unequal of 110mm dia with access door

M&L for PVC (SWR) vent cowl of 110mm dia

M&L for (SWR) gulley trap 125/110mm setting and jointing with solvent cement.

M&L for PVC (SWR) vent cowl of 75mm dia

S&F for PVC (SWR) floor trap 75mm dia with grating including jointing with solvent cement

M&L PVC (SWR) branch piece single Y equal or unequal of 110mm dia with access door

All as per Item No. 60 above but 75mm dia

Demolition - RCC (reinforcement cut as required to facilitate demolition) cover slabs and similar suspended work

M/L for providing precast RCC 1:2:4 type B1(using 20mm gde stone ag as in cover slabs for manholes set in CM (1:6) all as ( Note : Reinforcement shall be meashred & paid separately)

M&L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips - Deformed or twisted bars

S & F for providing MS bands, straps and handles for MH covers and rungs in manholes and similar small articles, all as directed conforming to Fe 290 Gde -E- 165

Taking down existing water proofing treatment of any description and layers from walls/roofs incl screed bed or bedding layers of mortar if any complete and cleaning the surface free from dust and scrubbing down with water complete and cleaning the surface free from dust and scrubbing down with water complete all as specified clearing off the premises all as directed by Engineer-in-Charge

M&Lfor providing 20 mm thick (averag thickness) screeding in CM 1:4 over roof slab to slope with water proofing compound, including edges of slabs and vertical surfaces finished evenly to receive WP treatment all as directed by Engineer-in-Charge (Note-integral water proofing compound will be measured and paid separetely )

Supply only intergal water proofing compound

M&L for preparing plastered surfaces @ 1.2 kg/Sqm with primer and applying water proofing treatment on roof wall, edges and vertical surfaces using APP modified membrane 3 mm thick with non woven polyster mat as reinforcement weighing not less than 3.5 Kg/Sqm and applying one coat of aluminium top reflecting coating above the membrane complete all as specified

Demolition of cement concrete in ground floor & pavings n exc 15 cm thick (below or above ground level)

M/L hard core of gauge n.exc 63mm, deposited, spread, and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface

M&L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded aggregate as in sub base,complete all as specified and directed.

M&L for providing & laying 100 mm thick Cement Concrete with Gde M-20 tremix concrete (design mix) with RMC and tremix machine by using 20mm graded coarse aggregates as in path/hardstanding/roads/slabs over drain; finished surface of concrete surface by brooming as required etc all as specified and directed by Engr-In-Charge

M&L for forming Contraction (dummy) joint 65mm deep x 10mm wide filled with sealing compound grade 'A'

M &L cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) 75mm thick

M & L PCC (1:3:6) type C-2 as in plinth protection & finishing the surface even & smooth (witout using extra cement ), 75 mm thick complete all as specified & directed.

M/L for providing plain cement concrete 1:2:4 type B1 using 20mm grade agg. as in coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work all as directed

M&L in repair precast cement concrete louvres and jallies, 25mm thick (mea sured solid), including all mouldings and setting in mortar complete with joints to match,type C0, 1:3:6 using 12.5 mm graded aggregate exc. 10 cm in width and setting in mortar 1:6, complete

Cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for and forming channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm dia pipe

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

M & L for excavating in post holes (or similar holes) each n exc 0.5 cu.m, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface of any type of soil

S& F Framed work such as grills, gratings,gates etc. with ends of bars shouldered and/ or rivetted or forged ionto spikes; framed guard bars; barred into doors ; ladders framed balustrades walk ways railings framework of watertanks & similar work portion framed & hung as gates including pintle hinges, stops, hand made sliding bolts etc. con-forming to Fe-290 Gde -E-165.

S&F for steel windows or ventilators, fixed type half portion and half open type complete with glazing bars dovetailed or welded etc all as directed and specified.

S&F for steel windows with side hung shutters incl projecting type hinges with steel handle, and peg stay, complete with glazing bars dovetailed or welded etc all as directed and specified.

S&F for 3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5sqm in each pane etc all as directed and specified.

M&L for preparation of new steel surfaces of any description over 10cm width/girth and applying two coat of synthetic enamel paint glossy over a coat of red oxide.

S&F in repairs for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I capacity 1000 Ltr complete fixed to pipe etc all as directed

M&L for ball brass valves high pressure with polythene float valve and fly nut complete screwed for iron pipe or brass ferrule and fixed in repairs Float valve 15mm

M&L for fixing 15mm Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe

M&L for fixing 20mm Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe

Demolition stone flooring /paving built in cement mortar laid bedded and pointed in cement mortar all as directed

Excavation over areas not exceeding 1.5 m deep and getting out in hard dense soil all as specified in directed by Engineer in charge

M&L for RCC 1:2:4 Type B1 1:2:4 (20 mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete

M&L for RCC 1:2:4 Type B1 1:2:4 (20 mm graded aggregate) Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

M &L Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

S&F mild steel rings & hooks in floors for tying horses complete all as specified and as directed. Note:- Rings & hooks are made of 16mm dia steel bar fixed with steel rod 30cm embedded in the floor all as directed by Engineer in Charge

S&F Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

S&F Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing complete including & over 15mm thick screed bed in CM 1:4

M&L for Rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces as in wall surfaces and 3 mm thick setting coat trowelled and even and smooth finished all as directed

Removing excavated soil n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

M & L for providing plain cement concrete 1:3:6 type C2 using 40mm grade agg. As in foundation filling and mass concrete/plinth cources all as directed

M & l for preparation of newly plastered surfaces of concrete surfaces and applying two coat of synthetic enamel paint over a coat of alkali resiatant primer all as specified and directed by engineer in charge

Taking down carefully copper/aluminium point wiring (light/fan/ socket /power etc.) complete removing the material to store for safe custody or for taking credit (credit for above items should be made as per conditions separately) and including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface

M&L for point wiring on PVC casing and capping confirming IS:3419-1988 with the help of multistranded unsheathed FRLS copper cable 1.5 sqmm 650/1100V grade confirming to IS:694 -1990 adhereing to colour code including earth wire of the size 1.5 Sqmm multi-stranded green colored connecting properly to the socket/ earth terminals with suitable terminal PVC boxes as required at site for One light /fan point controlled by one switch one way

M&L for point wiring on PVC casing and capping confirming IS:3419-1988 with the help of multistranded unsheathed FRLS copper cable 4 sqmm 650/1100V grade confirming to IS:694 -1990 adhereing to colour code including earth wire of the size 4 Sqmm multi-stranded green coloured connecting properly to the socket/ earth terminals with suitable terminal PVC boxes as required at site for One 3 pin socket outlet , 15 amps on independent board

M&L Switch socket combination outlet Conform IS 4615-1968, 2 in 1, 3 Pin 5/15 Amps flush type.

M&L switch piano Conform IS 4615-1968 flush type 5 Amps single pole one way.

S&F ceiling rose surface shall comply with IS :371-1979 Bakelite 60x 25 mm two to three terminals plates and of outside diameter not less than 63.5mm.

S&F polycarbonate angle holder retrofit type suitable for CFL/LED bulb of B-22 base including 01 nos 18/20 watt LED Bulb all as specified and directed by Engr-in-Charge.

S&F in replacement LED tube rod with diffused optics ultra bright LED tube light 18/20watt with high efficiency,integrated aluminum heat sink complete all as specified.

S&F in replacement 1x18/20W,230V surface and wall mounted batten suitable for installing LED Tube rod including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified .

S&F in replacement LED Building Security Light/Street Light fiitting 25 W,IP-65 protection made up of die cast aluminium housing with high power LED as lighting source complete fixing with GI bracket made out of 40mm bore GI pipe light grade 1.2 Mtr long bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed by Engr-in-charge. Make:Havells/Wipro/Luker

S&F MCB DB 04 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site. Make:Legrand/L&T/C&S

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing. Make: Legrand/L&T/C&S

S&F of C Curve MCB DP 32 Amps working on 240 volts, 50 HZ,10 KA all as specified and directed.

M & L for earthing complete with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground (earth pit plate kess than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement all as specified and directed by Engr-in-Charge.

M&L for exhaust fan of sweep 225/230 mm,single phase 240V of not less than 3 star BEE star rating , louvers and making hole by core cutting as per the required size of the exhuast fan and making good the disturbed surfaces and fixing to the wall with proper fasetner arrangements and all accessories complete all as specified and directed by Engr-in Charge. Make: Havells/Luker/Crompton

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2.5 Sqmm , 450/1100 Volts grade in and including PVC casing and caping ISI marked of size not less than 19 mm complete with conduit accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and directed (Two runs of 2.5 sqmm cable and one run of earth wire shall be measured as one RM)

M&L for laying XLPE underground cable 10 sqmm 2 core armoured sheathed with PVC cable stranded aluminium conductor 1100 volts grade

Excavation in trenches in soft/dis integrated rock n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed.

Supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as directed.

Supply and laying reinforced precast concrete cable cover, Class LV, Type 1, flat, size 250mm x 150mm x 40mm complete all as specified.

Material and labour for cutting of existing road/ hard standing by providing suitable T&P to make suitable size bore for fixing 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed by Engr-In-Charge

Supply & fix GI tubing light grade 50 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut,bolt,washers suitable size all as specified and directed at size.

SUN Enterprises

Sarkar Enterprises