Construction of GP building at Melige GP Thirthahalli taluk Shivamogga District

Providing and fixing Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steelrimer, including welding and bolted with special shaped washers etc.complete. Hot finished eamless type tubes including cost of aterials,labour, usage charges of machinery complete as per specifications andas per directions of the Engineer-in-Charge.( p no:81 i no 11.16.2 CSR Volume-2 2023-24 ) PWD SR

Basic Rate

Total

wall plates

100X50X3.2MIM

rafters

REEPERS

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coatedthickness, Zinc coating 120 g/m2 as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sideof thesheetand polyester top coat 15-18 microns using self drilling/ selftapping screws complete :

Basic Rate

Total

Basic Rate

Total

Supplying and fixing new Mangalore tiles on existing reepers ( p no: 207 i no 20.100 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

7.38 Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 g/m2 as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheetand polyester top coat 15-18 microns. Sheet should have protective guardfilm of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 m or as desired by Engineerin-charge. The sheet shall be fixed using self drilling/self tapping screws ofsize (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trussesand including cutting to size and shape wherever required. ( p no: 26 i no 7.38 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing Mangalore Ridge tiles set in C.M. 1:2 and pointed with C.M. 1:2. m( p no: 207 i no 20.98 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and constructing load bearing wall with Solid Concrete blocksof size 400x200x200mm having block ensity more than 1800kg/m3and minimum compressive strength of 4.00 N/mm2 conforming to IS2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005including cost of all materials, labour, scaffolding and curing,gecharges of machinery etc complete as per specifications. ( p no: 17 i no 6.32 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing 15 mm cement plaster on the rough side of single or half brickwall of mix :1:6 (1 cement: 6 fine sand) including rounding off cornerswherever required smooth rendering, providing and removing scaffolding,including cost of materials, labour, curing complete as per specificationsand as per directions of Engineer-in-charge. ( p no: 41 i no 8.2.2 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing Jungle wood such as Nerale, Neem wrought and putup forpurlins, common rafters and similar work including cost of materials,labour, usage charges complete as per specifications. ( p no: 99 i no 12.5 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing in position fully panelled Mathi/Nandi wood shuttersfor doors with stiles and rails of 40mm. thick with bottom and lock rails180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges completeas per specifications. (excluding cost of fixtures) ( p no: 77 i no 12.15 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing M.S. grills of required pattern in frames of windowsetc. with M.S. flats, square or round bars etc. including priming coat withapproved steel primer all complete. Fixed to steel windows by welding11.34B ( p no: 86 i no 11.34A ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear floatglass both side, having 12 mm air gap, including providing EPDM gasket,perforated aluminium spacers, desiccants, sealant (Both primary andsecondary sealant) etc. as per specifications, drawings and direction ofEngineer-in-charge complete including cost of materials, labour, usagecharges of machinery complete as per specifications and as per directionsof the Engineer-in-C ( p no: 91 i no 11.44 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and laying flamed finish Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stoneslab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directedby the Engineer-in-Charge :** Flamed finish granite stone slab Black, Cat Eye, River Pink or equivalent.( p no: 63 i no 9.23 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing, assembling and supplying vision glass panels (IGUs) comprisingof hermetically-sealed 6-12- 6 mm insulated glass (double glazed) visionpanel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour andshade with reflective soft coating on surface # 2 of approved colour andshade, an inner Heat strengthned clear float glass 6mm thick, spacertube 12mm wide, dessicants, including primary seal and secondaryseal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approvedshop drawings, as specified and as directed by the Engineer-in-Charge. TheIGUs shall be assembled in the factory/ workshop of the glass processor.(Payment for fixing of IGU Panels in the curtain glazing is included in costof item No.18.2)For payment, only the actual area of glass on face # 1 ofthe glass panels (excluding the areas of the grooves and weather siliconesealant) provided and fixed in position, shall be measured in m2.(i)Coloured tinted float glass 6mm thick substrate with reflective soft coatingon face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass ofapproved make having properties as visible Light transmittance (VLT) of25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided bytechnical sanctioning authority as per the site requirement.( p no: 183 i no 18.3 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Basic Rate

Total

Providing and laying in position Cement Concrete for levelling course forall works in foundation. The anite/trap/basalt crushed graded coarseaggregates and fine aggregates as per relevant IS Codes machine mixed, laid inlayers not exceeding 150 mm thickness, well compacted using plate vibrators,including all lead & lifts, cost of all materials of quality, labour, Usage charges ofmachinery, curing, and all the other appurtenances required to complete thework as per technical specifications. Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates ( p no: 15 i no 2.1.3 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcementincluding cost of all materials, machinery, labour, cleaning, straightening,cutting, bending, hooking, laping/welding joints, tying with binding wire / softannealed steel wire and other ancilary operations complete as per drawing andtechnical specification.a. Buildings ( p no: 18 i no 2.11 ) CSR Volume-1 2023-24 PWD SR

Basic Rate

Total

Providing and laying in position Reinforced cement concrete for allFoundation works. The granite/trap/basalt crushed graded coarseaggregates and fine aggregates as per relevant IS Codes machinemixed with super plasticizers laid in finished layers, well compactedusing needle vibrators, including all lead & lifts, cost of all materials,quality confirming to the requirements of relevant IS codes , labour,Usage charges of machinery, curing and all the other appurtenancesrequired to complete the work as per technical specifications. (The costof steel reinforcement & formwork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarseaggregates M25 Design mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 15 / 2.2.1 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 8% Centring charge

Total

Providing and laying in Reinforced cement concrete for all Sub structures of buildings, irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50m height. The granite/trap/basalt crushed graded coarse aggregates and fin aggregates as per relevant IS Coades machine mixed with super plasticisers, laid in layers, wll compacted usint needlee vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtemances required to complete the work as per technical specifications. (The cost of steel reinforcement & formawork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 81 / 2.4.3 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 70% Centring charge

Total

Providing and laying in position Reinforced cement concrete for all Super structures of buildings, Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement, dowel bars & formwork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 16 / 2.5.2 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 60% Centring charge

Total

WAIST SLAB STEPS AND LANDING

Basic Rate

Total

Add 50% Centring charge

Total

Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners, stainlesssteel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge,(for payment purpose only weight of stainless steel members shall beconsidered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery completeas per specifications and as per directions of the Engineer-in-Charge.1 (P.No. 85 / 11.28 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Basic Rate

Total

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approvedmake in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dadosover 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand)and jointing with grey cement slurry @ 3.3kg per m2 including pointing in white ceme ( p no: 60 i no 9.10 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions andcorners, all necessary fittings complete, including applying a primingcoat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonalbraces including cost of materials, labour, usage charges of machinerycomplete as per specifications and as per directions of the Engineer-inCharge ( p no: 77 i no 11.5.1 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing & fixing factory made PVC Door frame of size 50x47mm witha wall thickness of 5mm, made out of extruded 5mm rigid PVC foamsheet metered cut at corners & jointed 2 No.s of 150mm long bracketsof 15x15mm M.S Square tube, the entire door frame to be reinforced with19x19mm M.S Square tube of 19 gauge. The door frame to be fixed to thewall using M.S. Screws of 65/80mm size complete as per manufacturersspecification & direction of Engineer-in-charge. ( p no: 104 i no 12.54 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing & fixing 30mm thick factory made rigid foam Prelam PanelledDoor Shutters made from M.S. tube of 19x19mm, 19 gauge for stiles and15x15mm for top & bottom rails, covered with heat moulded Prelaminated PVC C Channel of 5mm thick sheet & 30x50mm wide to form stiles & 5mmthick & 75mm wide Prelaminated PVC Sheets for top rail, lock rail & bottomrail on either side & 5mm thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail, Panelling of 5mm thick PVC sheet Prelaminatedon either side fitted in the M.S. frame, Sealed to the stiles & rails with PVCDesigner beading on either side & joined together with solvent cement adhesive etc., Complete as per manufacturers specification & direction ofEngineer-in-charge fixed to frames with 3 nos of 75mm Aluminium hinges. -do- with one side prelam ( p no: 104 i no 12.55.2 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings and fixturescomplete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid ( p no: 123 i no 14.2.2 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing white vitreous china water closet squatting pan(Indian type) : Orissa pattern W.C. pan of size 580x440 mm each Extra for using ( p no: 126 i no 14.13.2 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

7.32 Providing and fixing false ceiling at all height including providing and fixingof frame work made of special sections, power pressed from M.S. sheetsand galvanized with zinc coating of 120 g/m2 (both side inclusive) as perIS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thickwith flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flangefixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mmdia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mmof required length with nuts & bolts of required size and other end of anglehanger fixed with intermediate G.I. channels 45x15x0.9 mm running at thespacing of 1200 mm centre to centre, to which the ceiling section 0.5 mmthick bottom wedge of 80 mm with tapered flanges of 26 mm each havinglips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a directionperpendicular to G.I. intermediate channel with connecting clips made outof 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixingperimeter channels 0.5 mm thick 27 mm high having flanges of 20 mmand 30 mm long, the perimeter of ceiling fixed to wall/partition with thehelp of rawl plugs at 450 mm centre, with 25mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section andperimeter channel with the help of dry wall screws of size 3.5 x 25 mm at230 mm c/c, including jointing and finishing to a flush finish of taperedand square edges of the board with recommended jointing compound,jointing tapes , finishing with jointing compound in 3 layers coveringupto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the costof making openings for light fittings, grills, diffusers, cutouts made withframe of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding thecost of painting with :7.32.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-(Part I) : 2011 (Board with BIS Certification marks only) 12.5 mm thick tapered edge Glass Reinforced Gypsum (P.No. 25 / 7.32.1 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Supplying of recess mounting non integrated type LED downlight...... W luminaire comprising of pressure decast/ extrudedaluminium housing, with spring loaded false ceiling clamps, LED ofPower/COB with CCT 6500 degree K, CRI> 70%. efficacy >100lumen per W, 120degree beam spread, life> 25000 burning hoursand Compliance to IS10322/IEC 60598, LM 79 & LM 80. The lampcompartment is enclosed with anti glare opal diffuser which enhances the lighting level. LED's are driven by HF electronic driverintegrated in a separate control gear assembly., with PF > 0.95, powerloss should< 5% of lamp Wage, short circuit & open circuit protectionto be integrated in the circuit, THD less than 20%, Life as per LM 79.The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with2 years Warranty against any manufacturing defect working understandard electrical condition. 10-12W Each (P.No. 25 / 11.4. 2 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Supplying of Ceiling Fan with Capacitor rating As per guideline ofBEE 5 star rating and IS:374/19 and also comply with IS: 1709/1984with latest amendment, Rated voltage 220 V/50 Hz, Rated power upto35 W +/- 10 %, Rated current As per IS:374/19, Rated power factor0.9 lagging(min), Rated speed 350 +/- 10% RPM, Rated air delivery 210 +/- 10% Cubic Meter Minimum, Rated service value 6.2 CMM /W, Three Blades of blade leaf 1.05 mm thick Aluminium Alloy sheet,Class B motor insulation, Bearing Two ball bearings, Top 6202,Bottom 6201, as per IS specification, Motor winding. Temp rise Shallnot exceed 75 deg C over and ambient of 40 0C by resistance method at 245 V, Insulation resistance Shall not be less than Two Mega Ohms(2M Ohms), Leakage current Should not exceed 210 Micro Amp,Power input, W& current, Air Delivery & Fan Speed as perIS:374/2019 with latest amendment, 2year manufacturer Warranty.(BLDC fans) 48" Sweep 5 Star (1200 mm) (P.No. 30 / 6.4.1 / CSR / Volume- 6 / 2023 - 24 )

Basic Rate

Total

Supplying and fixing surface/flush mounting unbreakable PVCmodular box suitable for mounting modular switch plates with duegroove cutting in Brick/C.C wall, including necessary rawl plugs,Machine/NF screws etc., complete. 6 Way (P.No. 8 / 3.3.4 / CSR / Volume- 6 / 2023 - 24 )

Basic Rate

Total

Supplying and flush mounting powder coated / galvanized metal boxsuitable for mounting modular switch plates. The box should be firmlyflush mounted after due groove cutting in Brick/Stone/C.C wall 6 Way (P.No. 8 / 3.4.4 / CSR / Volume- 6 / 2023 - 24 )

Basic Rate

Total

Supplying and fixing of modular switch & connected accessories onexisting modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch (P.No. 9 / 3.6.1 / CSR / Volume- 6 / 2023 - 24 )

Basic Rate

Total

2.3 Wiring for lighting/power circuit using one of FRLS PVC insulated1100V grade, multistrand copper wire with low conductor resistancesingle core in open or concealed system of wiring with specified IS694:2010 1.5 mm2 (P.No. 5 / 2.3.2 / CSR / Volume- 6 / 2023 - 24 )

Basic Rate

Total

add wc english and indian

Add 18% G.S.T

Tender premium

Third party charges

Misc and rounding off

Total Rs.

Certified that I have personally inspected the work spot and preparedthe estimate economically And with safe way of executing thek work.The rates adopted in the estimate is asper CSR for the year 2023-24. Items incorporated in the estimate for this work are Economically found correct.

Item Name

Providing and fixing Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steelrimer, including welding and bolted with special shaped washers etc.complete. Hot finished eamless type tubes including cost of aterials,labour, usage charges of machinery complete as per specifications andas per directions of the Engineer-in-Charge.( p no:81 i no 11.16.2 CSR Volume-2 2023-24 ) PWD SR

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coatedthickness, Zinc coating 120 g/m2 as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sideof thesheetand polyester top coat 15-18 microns using self drilling/ selftapping screws complete A.Ridges plain (500 - 600mm) ( p no:27 i no 7.39.1 ) CSR Volume-2 2023-24 PWD SR

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coatedthickness, Zinc coating 120 g/m2 as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sideof thesheetand polyester top coat 15-18 microns using self drilling/ selftapping screws complete Gutter (600 mm over all girth) ( p no:27 i no 7.39.6 ) CSR Volume-2 2023-24 PWD SR

Supplying and fixing new Mangalore tiles on existing reepers ( p no: 207 i no 20.100 ) CSR Volume-2 2023-24 PWD SR

Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 g/m2 as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheetand polyester top coat 15-18 microns. Sheet should have protective guardfilm of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 m or as desired by Engineerin-charge. The sheet shall be fixed using self drilling/self tapping screws ofsize (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trussesand including cutting to size and shape wherever required. ( p no: 26 i no 7.38 ) CSR Volume-2 2023-24 PWD SR 7.38

PÁªÀÄUÁjAiÀÄ ºÉ¸ÀgÀÄ : wÃxÀðºÀ½î vÁ®ÆèPÀÄ

CAzÁdÄ ªÉÆvÀÛ : 25.00 ®PÀë

¯ÉPÀÌ ²Ã¶ðPÉ :

Providing and fixing Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steelrimer, including welding and bolted with special shaped washers etc.complete. Hot finished eamless type tubes including cost of aterials,labour, usage charges of machinery complete as per specifications andas per directions of the Engineer-in-Charge.( p no:81 i no 11.16.2 CSR Volume-2 2023-24 ) PWD SR

Basic Rate

Total

wall plates and benkti

100X50X3.2MIM

rafters

REEPERS

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 g/m2 as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sideof the sheet and polyester top coat 15-18 microns using self drilling/ selftapping screws complete :

Basic Rate

Total

Basic Rate

Total

Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm(+ 0.05 %) total coated thickness with zinc coating 120 grams per m2 asper IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on bothside of the sheet and polyester top coat 15-18 microns. Sheet shouldhave protective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto 12m or as desired by Engineer-in-charge. The sheet shall be fixed usingself drilling/self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved rfaces,excluding the cost of purlins, rafters and trusses and including cuttingto size and shape wherever required.( p no:26 i no 7.38) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and constructing load bearing wall with Solid Concrete blocksof size 400x200x200mm having block density more than 1800kg/m3and minimum compressive strength of 4.00 N/mm2 conforming to IS2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005including cost of all materials, labour, scaffolding and curing, usagecharges of machinery etc complete as per specifications. ( p no: 17 i no 6.32 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing 15 mm cement plaster on the rough side of single or half brickwall of mix :1:6 (1 cement: 6 fine sand) including rounding off cornerswherever required smooth rendering, providing and removing scaffolding,including cost of materials, labour, curing complete as per specificationsand as per directions of Engineer-in-charge. ( p no: 41 i no 8.2.2 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing Jungle wood such as Nerale, Neem wrought and putup forpurlins, common rafters and similar work including cost of materials,labour, usage charges complete as per specifications. ( p no: 99 i no 12.5 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing in position fully panelled Mathi/Nandi wood shuttersfor doors with stiles and rails of 40mm. thick with bottom and lock rails180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges completeas per specifications. (excluding cost of fixtures) ( p no: 77 i no 12.15 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing M.S. grills of required pattern in frames of windowsetc. with M.S. flats, square or round bars etc. including priming coat withapproved steel primer all complete. Fixed to steel windows by welding11.34B ( p no: 86 i no 11.34A ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear floatglass both side, having 12 mm air gap, including providing EPDM gasket,perforated aluminium spacers, desiccants, sealant (Both primary andsecondary sealant) etc. as per specifications, drawings and direction ofEngineer-in-charge complete including cost of materials, labour, usagecharges of machinery complete as per specifications and as per directionsof the Engineer-in-C ( p no: 91 i no 11.44 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

9.23 Providing and laying flamed finish Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stoneslab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directedby the Engineer-in-Charge :** Flamed finish granite stone slab Black, Cat Eye, River Pink or equivalent.( p no: 63 i no 9.23 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Basic Rate

Total

2.1 Providing and laying in position Cement Concrete for levelling course forall works in foundation. The granite/trap/basalt crushed graded coarseaggregates and fine aggregates as per relevant IS Codes machine mixed, laid inlayers not exceeding 150 mm thickness, well compacted using plate vibrators,including all lead & lifts, cost of all materials of quality, labour, Usage charges ofmachinery, curing, and all the other appurtenances required to complete thework as per technical specifications. Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates ( p no: 15 i no 2.1.3 ) CSR Volume-2 2023-24 PWD SR

Basic Rate

Total

Basic Rate

Total

Providing and laying in position Reinforced cement concrete for allFoundation works. The granite/trap/basalt crushed graded coarseaggregates and fine aggregates as per relevant IS Codes machinemixed with super plasticizers laid in finished layers, well compactedusing needle vibrators, including all lead & lifts, cost of all materials,quality onfirming to the requirements of relevant IS codes , labour,Usage charges of machinery, curing and all rappurtenancesrequired to complete the work as per technical specifications. (The costof steel reinforcement & formwork to be paid arately) M25 Design Mix Using 20 mm nominal size graded crushed coarseaggregates M25 Design mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 15 / 2.2.1 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 8% Centring charge

Total

Providing and laying in Reinforced cement concrete for all Sub structures of buildings, irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50m height. The granite/trap/basalt crushed graded coarse aggregates and fin aggregates as per relevant IS Coades machine mixed with super plasticisers, laid in layers, wll compacted usint needlee vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtemances required to complete the work as per technical specifications. (The cost of steel reinforcement & formawork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 81 / 2.4.3 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 70% Centring charge

Total

Providing and laying in position Reinforced cement concrete for all Super structures of buildings, Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement, dowel bars & formwork to be paid separately) M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. (P.No. 16 / 2.5.2 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 60% Centring charge

Total

WAIST SLAB STEPS AND LANDING

Basic Rate

Total

Add 50% Centring charge

Total

Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners, stainlesssteel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge,(for payment purpose only weight of stainless steel members shall beconsidered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery completeas per specifications and as per directions of the Engineer-in-Charge.Providing & fixing (P.No. 85 / 11.28 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

7.32 Providing and fixing false ceiling at all height including providing and fixingof frame work made of special sections, power pressed from M.S. sheetsand galvanized with zinc coating of 120 g/m2 (both side inclusive) as perIS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thickwith flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flangefixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mmdia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mmof required length with nuts & bolts of required size and other end of anglehanger fixed with intermediate G.I. channels 45x15x0.9 mm running at thespacing of 1200 mm centre to centre, to which the ceiling section 0.5 mmthick bottom wedge of 80 mm with tapered flanges of 26 mm each havinglips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a directionperpendicular to G.I. intermediate channel with connecting clips made outof 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixingperimeter channels 0.5 mm thick 27 mm high having flanges of 20 mmand 30 mm long, the perimeter of ceiling fixed to wall/partition with thehelp of rawl plugs at 450 mm centre, with 25mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section andperimeter channel with the help of dry wall screws of size 3.5 x 25 mm at230 mm c/c, including jointing and finishing to a flush finish of taperedand square edges of the board with recommended jointing compound,jointing tapes , finishing with jointing compound in 3 layers coveringupto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the costof making openings for light fittings, grills, diffusers, cutouts made withframe of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding thecost of painting with :7.32.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-(Part I) : 2011 (Board with BIS Certification marks only) 12.5 mm thick tapered edge Glass Reinforced Gypsum (P.No. 25 / 7.32.1 / CSR / Volume- 1 / 2023 - 24 )

Basic Rate

Total

Add 18% G.S.T

Third party charges

Misc and rounding off

Total Rs.

Certified that I have personally inspected the work spot and preparedthe estimate economically And with safe way of executing thek work.The rates adopted in the estimate is asper CSR for the year 2023-24. Items incorporated in the estimate for this work are Economically found correct.