Repair and Restoration of Chocked and Damaged underground Pipeline water course of Bora Distributory and Distribution System at RD 110.491KM of Kandi Canal stage-2.

Amount

(2) WATER SUPPLYExcavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect.

Earth work upto 1.5 m. Depth for

All classes of soil except rocky

For Ordinary soil having gravel upto 40%

Providing & fixing Single air valve ISI Marked as per IS-14845 including jointing , cost of nut bolts & rubber insertion all carriages complete.

C.I Single air screwed (Size 50mm) valve

Providing & fixing double air valve ISI Marked as per IS-14845 including jointing all carriages complete.

C.I Double air (Size 100mm) valve

Construction masonary Sluice of Valve Chamber excluding Sluice valve cover as per standard design & drawings of public health department.

(a) Size 0.6 m. x 0.6 m.

(b) Size 0.9 m. x 0.9 m.

Development and Stabilizing of the tubewell with air compressor of required capacity as directed by the engineer-in- charge including cost of tools, appliances & consumable to the satisfaction of Engineer-in-charge. (For D-choking of pipes)

Capacity of Air compressor 300 cfm at 250 PSI

Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge). clacc PN-1.6as per ISI

150mm i/d Sluice Valves flanged

200mm i/d Sluice Valves flanged

MATERIALS Aggregates (average rate of all the quarries) Note:- Quarry wise aggregates rates attached at Annexure-I)

Fine Sand with FM not less than 1.6

BRICK WORK First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth

PLASTERING & POINTING

10mm thick Cement Plaster 1:3

CONCRETE 1:2:4 Cement concrete mixing by mechanical means using concrete mixer volumetric type

STEEL AND IRON WORK Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

CENTRING AND SHUTTERING Shuttering for precast and plain or Reinforced concrete blocks, wall plates, bedplates, shelves etc.

ROAD WORK

Dismantling of Flexible Pavements (By Mechanical Means)-Dismantling of flexible pavements thickness above 50mm by mechanical means and disposal of dismantled materials up to a lead of 1000 meters, stacking serviceable and unserviceable materials separately as per technical clause 202 of MORT&H specifications

Water Bound Macadam Grading II: Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical clause 404 of MORT&H specifications

Tack Coat @ 0.40kg per sqm: Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical specifications

Semi-Dense Bituminous Concrete 35mm to 40mm thickness (Grading I)

Providing and laying semi dense bituminous concrete 35mm to 40mm thick with batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 4.5%, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per IRC-111 (2009) specifications

Providing , stringing out , cutting jointing and testing 350mm AC pipes ISI marked as per IS 1592:2003 class 15 with suitable AC Coupling along the trench and laying the same into trenches to correct alignment and gradients , including all carriage complete.

Providing of CID joints long collar350mm including carriage to site of work and testing etc. complete in all respect as per PWD specifications and instructions

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 160mm of superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 180mmof superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 200mm of superior make @ 2.5 kgf /sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 225mm of superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 250mm of superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 280mm of superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Providing, Laying, fixing & jointing of uPVC Socketed type Pipe dia. 315mmof superior make @ 2.5 kgf/sq cm pressure as per ISI-4985(ISI marked with the prior approval of Engineer in charge) along the trenches and laying the same in trenches to correct alignment and gradient, cutting, jointing and testing complete as per specifications

Supply & fixing UPVC Long bend 160mm 90 degrees of different angle of 6kgf pressure conforming to IS-codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Supply & fixing UPVC Long bend 160mm 45 degree of different angle of 6kgf pressure conforming to IS-codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Supply & fixing UPVC Long bend 180mm 90 degree of different angle of 6kgf pressure conforming to IS-codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Supply & fixing UPVC Long bends 200mm 90 degree of different angle of 6kgf pressure conforming to IS-codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Supply & fixing UPVC Long bend 225mm 45 degree of different angle of 6kgf pressure conforming to IS-codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Providing & fixing alpha valve 160MM including carriage, rehandling, loading, unloading, testing, etc. complete in all respect as per PWD specifications or instructions of the engineer in charge.

Providing & fixing alpha valve 180MM including carriage, rehandling, loading, unloading, testing, etc. complete in all respect as per PWD specifications or instructions of the engineer in charge.

Providing & fixing alpha valve 200MM including carriage, rehandling, loading, unloading, testing, etc. complete in all respect as per PWD specifications or instructions of the engineer in charge.

Providing & fixing UPVC Reducer/ Increaser of180X160MM 6Kgf pressure conforming to IS codes with latest amendments if any at site of work including loading, unloading and rehandling if any complete in all respects as per design and P.W.D. specifications and instructions of engineer in charge.

Supply & fixing of service saddle M.S.160x50mm conforming to code with latest amendments if any at site including carriage, loading, unloading & rehandling complete in all respect as PWD specifications or instructions of the Engineer In Charge

Supply & fixing of service saddle M.S. 180x50mm conforming to code with latest amendments if any at site including carriage, loading, unloading & rehandling complete in all respect as PWD specifications or instructions of the Engineer In Charge

Supply & fixing of UPVC equal-Tee of 160X160X160MM 6 kg/cm2 pressure conforming to IS-codes with latest amendments if any at site of work. including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply & fixing of UPVC equal-Tee of 180X180X180MM 6 kg/cm2 pressure conforming to IS-codes with latest amendments if any at site of work. including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply & fixing of UPVC equal-Tee of 200X200X200MM 6 kg/cm2 pressure conforming to IS-codes with latest amendments if any at site of work. including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply and fixing flange tail end point of 6kgf with M.S. flange 160MM including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply and fixing flange tail end point of 6kgf with M.S. flange 180MM including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply and fixing flange tail end point of 6kgf with M.S. flange 200MM including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply and fixing flange tail end point of 6kgf with M.S. flange 225MM including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

Supply and fixing flange tail end point of 6kgf with M.S. flange 250MM including carriage, rehandling, loading , unloading , testing etc. complete in all respects as per PWD specifications or instructions of the Engineer-in-charge

any other item

The Lambra Co Operative L and C Society Ltd