Interior Design/ Furnishing for Multipurpose Hall and Indoor Stadium at Polytechnic College Karad, Silvassa

Amount

Providing and installing 6.5 mm overall thick indoor stadium flooring make of Wonder floor/LG or equilent, the highly resilient 1.00 mm wear layer is produced using specialty resins that takes care of the heavy abrasion loads. The ‘Impregnated Glass Fiber Tissue” reinforcement provide a very high dimensional stability and lay flat properties to the product in any weather conditions. It should be slip resistance and Class 1 surface spread of flame, it has weight 4.5 KG/m2 weight. Floor to be installing at badminton court and sport court with help of adhesive and joint should be welded by welding cored, marking by special sport paint for badminton court and sport court as per instructed by architect, sample shall be submitted to Client/Architect in charge for approval.

SITC two-way peformance speaker with 1” dome tweeter and a 8” low frequency loudspeaker, capable of delivering a power of 70 Watt, 100V PA system with tap of 60 Watt, 30 Watt, and 15 Watt. RMS Power of 70 Watt & Max Power of 140 Watt at 16 ohms. Coverage pattern of 110° x 110°, Sensitivity (1W/1m) 89 dB, Max SPL 106 dB.(Bose/QSC/AUDAC)

SITC mixer amplifier that runs on 100V lines and Impedance modes, Frequency Response 50hz-20Khz System Output 500W rms, Distortion <= 1%@1 kHz, S/N Radio >= 76db (Aux), 66db (Mic), Inputs USB/SD/Aux/CD/computer Mic Input 1 Mics, two zone. (JBL/STONEWATER/Audac)

SITC Dynamic transducer type, cardioid polar pattern, frequency response 70Hz - 15KHz wired microphone. (Studio Master, Shure, AKG, Senniheiser)

2 Core speaker cable, ATC Copper conductor, PVC insulated, Cores twisted in circular form, Jacketed with PVC, CROSS SECTION AREA: 15 SQMM. (Krystal, MX, Balden, Bandridge or equivalent.)

MS Locker: Supply of locker unit made out of MS 22/24 gauge sheet finished with powdercoating (at Ground floor change room, Player's waiting area beside equipment simulation centre, Store cloak room for visitor) Size 78" x 36" x 19"

M S perforated seating finished with powdercoating finish 55" length

Cupboard storage in bathroom , carcase skull made out of Action tesa/Green panel make 25mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters made out of 16mm HDHMR shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6'w x 7'h x1'10"d

Cupboard storage in bathroom , carcase skull made out of Action tesa/Green panel make 25mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters made out of 16mm HDHMR shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 5'w x 7'h x1'10"d

Main table , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. 6mm Corian on table top as per architect's specificatoin (At Coach room, Equipment simulation center, Head office cabin main table, Medical room main table ) Size 6' x 2'6" x 2'6"

Side credenza , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. (At Coach room, Equipment simulation center, Medical room main table ) Size 3' x 2'6"ht x 1'6"d

Side credenza , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. (At Head office cabin main table ) Size 2'6" x 2'6" ht x 1'6" d

Back side storage , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. At Head office cabin main table 12' x 2'6" x 1'6" d

Back side storage , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. At Medical room main table 7' x 2'6" x 1'6" d

Receiption counter , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Counter top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. , Color HDF( VENTURA or equivalent) to be used as per drawing detail Size 10' x 2'5"x 2'5"

sofa with wooden handle using framework made out of waterproof plywood finished with Kurlon make 40 D x 4"+2" soft foam seat cushion & 32D on rest area, fabric range rs 500 - 650 rs per meter (At Player's rest area out side coach room 3 seater, Head office waiting area 3 seater, Receiption area 3 seater ) Size 7 Rnft

sofa with wooden handle using framework made out of waterproof plywood finished with Kurlon make 40 D x 4"+2" soft foam seat cushion & 32D on rest area, fabric range rs 500 - 650 rs per meter (At Player's rest area out side coach room 3 seater, Head office waiting area 3 seater, Receiption area 3 seater ) Size 5 Rnft

Centre table made out of 12mm toughened glass top, Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area ,all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. (At Player's rest area out side coach room ,Head office waiting area,Receiption area ) Size 3'3" x 2'

Corner table made out of 12mm toughened glass top , Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area ,all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. (At Player's rest area out side coach room, Head office waiting area and Receiption area ) Size 2' x 2'

Wall panelling using made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , Color HDF( VENTURA or equivalent) to be used as per drawing detail (At Head office back side wall, Receiption back side wall ) Size 10' x 10'

Bed without storage & without matress made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6'6" x 4'

Bed without storage & without matress made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6'6" x 5'

Wall mount side table made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 2' x 1'6"

Wardrobe made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6' x 7' ht x 1'10"

sofa with wooden handle using framework made out of waterproof plywood finished with Kurlon make 40 D x 4"+2" soft foam seat cushion & 32D on rest area, fabric range rs 500 - 650 rs per meter Size 5 Rnft

Centre table made out of 12mm toughened glass top, Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area ,all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 3' x 2'

Wall mount side table made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 1'6" x 1'6"

Wall mount side table made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 9'6" x 3'6" At Head Room

Discussion table made out of Action tesa/Green panel make 25mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , mounted on metal understructure finished with powdercoating s per approved shade and 25mm top edge shall be finsihed with REHAU make 2mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 2'6" x 2'6"

Main Table made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Table top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6' x 2'6" x 2' d

Side Table made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Table top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 4' x 2'6"

Seating made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Table top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 8' x 2'

Couch for treatment made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 6' x 3'

Side box beside couch made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 3'3" x 1'6"

Side box beside couch made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 15" x 15"

Side box beside couch made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 4'7" x 2'6"

Storage Cabinate made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 9' x 7'

Storage Cabinate made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make)all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. Size 5'3" x 7'

Receiption counter , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Counter top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. , Color HDF( VENTURA or equivalent) to be used as per drawing detail Size 7'6" x 2'6" x 2'6"

Receiption counter , made out of Action tesa/Green panel make 16mm HDHMR finished with 1mm laminate( FORMICA/ ARCHID/MERINO or equivalent make ) on outside area & 0.8mm liner in inside area , shutters shall be mounted on heavy duty soft close auto hinges & other hardware ( EBCO/GODREJ or equivalient make), Counter top shall be finished with 6mm Corian ( LG/3M or equivalent make) all panel shall be finsihed with REHAU make 1mm PVC edgebanding pasted on automatic edgebanding machine using JOWAT make glue melted at 180 degree. , Color HDF( VENTURA or equivalent) to be used as per drawing detail Size 13' x 2' x 2'6"

TRANSPORTATION PACKAGING & FORWARDING of furniture items

Signage's : with LED light Providing and fixing Signage's comprising of wooden fiber sheet / Cement sheet / Viroc sheet/ACP/SS / Acrylic plate letter made from 3 mm film with Vinyle Acrylic Alfacompany),(including necessary framing work if required with anti corrosion paint. The rate shall be for complete item inclusive of all material, labor, wastages, necessary tools & tackles, adhesives, consumable hardware & required SS 304 grade hardware/accessories , LED light of approved make. Work complete including all type of material, fittings , fixtures,Finish, loading , unloading , transporation, , all leads ,accessories, sample mockup, all floor , all levels, all heights , etc complete as per drawings ,specifications & instruction of Client/EIC.

Plain gypsum board MRFR grade ceiling: Plain gypsum MR& FR grade false ceiling Suspension( considering all levels with require all fabricataion work and fitiing from RCC slab to false ceiling up to 150 to600 mm & The rate shall be consider in sqm for all floors and at all heights ,Offsets whether covelight or fixed gypsum board size up to 100 mm to 1200 mm in the false ceilings including all costs) . Work complete as per the manufacturers specification of Saint Gobain - M/F Suspended Ceiling 1 hour fire rated .:Providing and fixing Suspended ceiling using Gypsum or equivalent of ULtra G. I. Perimeter Channels of size 0.55mm thick having one flange of 20mm and another flange of 30mm and web 27mm along with perimeter of ceiling, screw fixed to brick wall / partitions with the help of nylon sleeves and screws, at min. 600 mm centers. Then suspending G. I. intermediate channel of size 45mm, 0.9mm thick with two flanges of 15mm each from the soffit at 1220mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with G. I. cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centers. 12.5mm gypsum MR/FR grade Board (conforming to IS 2095 part 1 2011) is then screw fixed to ceiling section with 25mm dry wall screwed at 230mm centers. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the edges of the boards with jointing compound, Joint paper tape and two coats of Drywall top coat suitable for Gypsum Board. Cutouts For light fittings, grill diffusers shall be made. Necessary cutting / providing openings in the ceiling for AC fixtures, grills, electrical fittings, or other utility services, hatch openings etc. shall be provided by the Contractor and cost of making such modifications shall be included in the price. No separate charges for cutting / providing opening will be paid. Trap doors with necessary ply frame work to be provided as required at no extra cost.Joints between the two gypsum board, (Board placed staggered) gypsum board and wall will have suitable tape and finishes with plaster of paris so as to have crack free joints.

Grid Ceiling: Providing and Fixing of Light weight Calcium Silicate Ceiling Tiles – Microlook edge of size 595x595x15mm densified edge ,having 100% RH –High Heat & Humidity Resistance) suitable for all weather conditions , and Fire Performance - Non Combustible as per BS 476 part 4,Anti fungal & Antibacterial,Eco friendly, Zero VOC, Non hazardoud, Noise Reduction Coefficient of ranging from 0.5 NRC to 0.75NRC depending on the Product, CAC of 32dB,Light reflectance above 85%, density of 450 Kg/m3, Thermal Conductivity of 0.043 W/mo k C, to be laid on of true horizontal level 15 mm exposed hot dipped galvanized steel sections in tech panel Format where in main tee having a 150 Route fall intersection notch for insertion of 150 mm Cross Tee wherever Required to make a tech panel grid Format with 150X 1200 MM Tech Panels of metal Gi plain having Microlok Edge to incorporate all the services on the tech panel and complete as desired by engineer incharge.Necessary cutting / providing openings in the ceiling for AC fixtures, grills, electrical fittings, or other utility services, hatch openings etc. shall be provided by the Contractor and cost of making such modifications shall be included in the price. No separate charges for cutting / providing opening will be paid. Trap doors with necessary ply frame workto be provided as required at no extra cost. Work complete as per the detailed drawing and instruction of Architect/EIC.

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 450 C. The outlet temp. of the water should drop by 150C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Air Handling Unit Supply, Installation, Testing and commissioning (SITC) of Sheet metal sectionalised cabinet type air handling unit in Double skin construction fabricated from Al extruded section frame structure. The inner skin 24G & outer skin 22G GI constrution with 43 mm thick PUF insulation panel complete with following sections: Mixing Chamber, Prefilter section with Pre filter(10 Micron & 90 % Efficiency), Coil section with DX coil with 12 FPI / Max. 500 FPM (To be designed to suit respective TR/CFM capacity for each AHU), Blower (DIDW BACKWARD CURVED FAN) section with Blower and motor, both Motor and Blower are mounted on common base frame, Microvee filter section with M.V. filter In Aluminium construction(5 Micron&95 % Efficiency), Fresh air Module With S.S. bird screen, volume control damper and 20 Micron Filter(90 % Efficiency), Exhaust air Module With S.S. bird screen ,volume control damper and 20 Micron Filter(90 % Efficiency), Sandwich type insulated drain pan ,drain pan should be 18 G SS construction, Magnahelic Guages with Necessary Tubing across Pre Filter (0- 25mm of W.G.) Microvee filter (0-25 mm of W.G.), Mixing chamber should be of minimum 500 mm, Prefilter section should be of Minimum 200 mm for 50mm Thick filter size (for higher filter thickness ,difference in thickness will be added in pre- filter section).Coil section should be of minimum 500 mm. Blower section length should be as per standared dimension of the blower required to install the blower in housing. After blower and before Microvee filter there should be gap of 500 mm. There should be gap of 500 mm Between M.V. filter and discharge. There should be access door across every section of AHU. Necessary openings for Magnahelic gauges & electrical connections.(a) DX-AHU - 6000 CFM @ 65 MM TSP - 15 TR CITIZEN, TRANE or EQUIVALENT

Supply, Installation, Testing and commissioning (SITC) Ceiling Suspended Ductable unit having nominal cooling capacity as mention below (a) suitable to work with cordless/ Corded/Centralised Remote arrangement VRF system (b) working on 230 V, 50 cycles, A.C. supply. (c) The indoor unit must have electronic expansion valve operated by microprocessor thermostat based tempreture control to deliver cooling as per manufacturers standard specifications (d) These units shall be ceiling suspended with suitable supports to take care of operating weight of the unit, without causing any excessive vibration & noise. (e) The cold air supplied by these units will be supplied to the area to be air conditioned, through duct system specified in the tender.(A) 6.0 TR 2300 CFM BLUE STAR, HITACHI, VOLTAS or EQUIVALENT

Supply, Installation, Testing and commissioning (SITC) Ceiling Suspended Ductable unit having nominal cooling capacity as mention below (a) suitable to work with cordless/ Corded/Centralised Remote arrangement VRF system (b) working on 230 V, 50 cycles, A.C. supply. (c) The indoor unit must have electronic expansion valve operated by microprocessor thermostat based tempreture control to deliver cooling as per manufacturers standard specifications (d) These units shall be ceiling suspended with suitable supports to take care of operating weight of the unit, without causing any excessive vibration & noise. (e) The cold air supplied by these units will be supplied to the area to be air conditioned, through duct system specified in the tender.(B) 11.0 TR 4400 CFM BLUE STAR, HITACHI, VOLTAS or EQUIVALENT

Supply, Installation, Testing and commissioning (SITC) of fully Indiginous factory assembled variable refrigerant flow (VRF) unit. The unit shall be complete with the following capacity outdoor unit - Multiple(minimum two) Inverter scroll compressors with both Compressors are controlled by DC inverter Technology - Micro processor based unit mounted compressor starter/ control panel with suitable rain protection covers - Built in oil seperator, accumulator & oil receiver - Suitable for longer piping length upto 1000m - Sutable to work on 3 phase 415 volts 50HzA.C Supply - Complete with necessary R410A Refrigerent Gas Charging as per the site condition for satisfactory operation entire system complete with testing for leakages as per OEM Specs - Air cooled condenser coil- Squore shaped heat exchanger to increase heat transfer area, high COP & lower power consumption with fan, motor and starter - Controls comprising HP/ LP cutout, cooling thermostats etc - Remote Monitoring Facility for all recording the Parameters/Performnace of the System in OEM's Service Centre & attending breakdown calls accordingly - Interconnecting copper piping, valves, power wiring, control wiring and earthing - Constructed from polysterpowder coated sheet metal housing - Equipment supplied shall be of non chinese make origin - The ODu's are designed so that at 42 Deg C Ambient Temperature the unit shall able to work at 100% capacity (A) 46 HP

Supply, Installation, Testing and commissioning (SITC) of fully Indiginous factory assembled variable refrigerant flow (VRF) unit. The unit shall be complete with the following capacity outdoor unit - Multiple(minimum two) Inverter scroll compressors with both Compressors are controlled by DC inverter Technology - Micro processor based unit mounted compressor starter/ control panel with suitable rain protection covers - Built in oil seperator, accumulator & oil receiver - Suitable for longer piping length upto 1000m - Sutable to work on 3 phase 415 volts 50HzA.C Supply - Complete with necessary R410A Refrigerent Gas Charging as per the site condition for satisfactory operation entire system complete with testing for leakages as per OEM Specs - Air cooled condenser coil- Squore shaped heat exchanger to increase heat transfer area, high COP & lower power consumption with fan, motor and starter - Controls comprising HP/ LP cutout, cooling thermostats etc - Remote Monitoring Facility for all recording the Parameters/Performnace of the System in OEM's Service Centre & attending breakdown calls accordingly - Interconnecting copper piping, valves, power wiring, control wiring and earthing - Constructed from polysterpowder coated sheet metal housing - Equipment supplied shall be of non chinese make origin - The ODu's are designed so that at 42 Deg C Ambient Temperature the unit shall able to work at 100% capacity (A) 76 HP

Providing and erecting Blue Star make VRF Hi-Wall air-conditioning unit with accessories etc. (A) 1.5 TR AT GREEN ROOM

Providing and erecting Blue Star make VRF Hi-Wall air-conditioning unit with accessories etc. (A) 2.0 TR AT VIP LOUNGE

Supplying, erecting, Testing & commissioning Centralised programmable Remote contol Panel which controls minimum 16 System of 64 ODU's can be controlleed & up to 992 IDU's can be individually controlled.,yearly scheduling can be done,

Supplying, erecting, Testing & commissioning Corded Remote Controller Remote contol for Ductable IDU having colour LCD panel, Real Time Clock,temperature limitation(16 to 30Deg Cent., Functions Like Filter Clean reminder Timer suitable to communicate with wired controller complete

Supplying, erecting, Testing & commissioning Cordless Remote contol having colour LCD panel, Real Time Clock,temperature limitation(16 to 30Deg Cent., Functions Like Filter Clean reminder Timer suitable to communicate with wired controller complete

AHU Kit

Copper Refrigerant Distribution Joints (Refnets)

Supply and laying of high pressure grade Hard drawn Copper refrigeration pipe, having minimum 1mm thickness with required size Nitrile rubber insulation complete with brazing Testing for leakages, erected on wall/ceiling with GI Hanger supports/raceways, with, painting etc. ( Pipe Sizes as per manufactures designs.. Vendor to Obain Manufactur's Approval on sizing before starting the work)

Supply, installation, testing & commissioning of control and communication cabling between the indoor and outdoor units in the rigid PVC conduit.

Supplying, and charging Addl fresh eco- friendly refrigrent gas R410A to the VRF/VRV System in an approved manner

Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 (A) Thickness 0.63 mm sheet (24 gauge)

Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 (A) Thickness 0.63 mm sheet (24 gauge)

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Acoustic insulation for Duct 10mm thick armasound

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. - 13 mm

Supplying & Providing thermal OverDeck insulation Glasswool - 50mm Thk

Supplying & erecting .Canvas Connection between Ductable unit Damper/Ducting as the Duct size requirements

Sound Attenuator (Duct Silencer) Manufactured from 20G GI sheet. Accoustic insulation made of fiberglass tissue protected by aluminum perforated plate Attenuating splitters are constructed from press formed frame Attenuator casing is welded and sealed with mastic to assure low casing leakage Size: 700mm (W) X 900mm (H) X 600mm (L)

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying & erecting rigid UPVC Drain pipe with PVC accessories on wall/ceiling as per specification for Drain Pipe complete with Elastomeric Nitrile rubber/foam tube type sleeves for over coating and insulating on provided copper pipes having 9 mm thickness as per following Sizes (A) 25 mm dia.

Supplying & erecting rigid UPVC Drain pipe with PVC accessories on wall/ceiling as per specification for Drain Pipe complete with Elastomeric Nitrile rubber/foam tube type sleeves for over coating and insulating on provided copper pipes having 9 mm thickness as per following Sizes (B) 32 mm dia.

Supplying and erecting Iron work consisting of Various sections of MS and including Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority for ODU

Supply of Propeller fans for Toilet Exhaust, suitable for wall-mounting installation. (A) 150 CFM 5mm Wg ESP

Providing and fixing approved make Perforated C type cable tray. Made from pre- galvanized CR sheet steel. The cable tray should be bended as per IS 2062/1079 . with coupler plate / Fish plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as per instruction of engineer in charge. (B) 300 X 50 X 1.5 mm Thick

Supplying & erecting PVC copper armoured cable 4 core 6 sq mm complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification

Supplying & erecting PVC copper armoured cable 4 core 16sq mm complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per

Supply Installation of MCB'S in weatherproof Box as per manufacturer specification etc. complete

Providing & fixing G.I. 10 Gage earthing wire draw with each and every cable etc. complete

Loading - Unloading, Lifting, Shifting of All units

Providing & fixing Core cutting etc. complete

Providing material and labour for Minor civil work such as wall Opening and chasing, chiseling etc.

AHU Starter Panel: Powder Coated PLC Based Control Panel and monitoring system with remote monitoring and Data logging facility. Which include motor and Fan on/off switch with indicating lamp.Panel shall have analog voltage and current meter and data log.

MCB for Outdoor Unit

SITC (Supply, Installation, Testing and Commissioning)Ceiling flyable three-way cabinet with 15” Horn-loaded Mid-Bass driver, 6” loaded Mid Driver and 1.75” Compression Driver. RMS Power of 750 Watt & Max Power of 1500 Watt at 8 ohms. Coverage pattern of 90° x 40°, Sensitivity (1W/1m) 105 dB, Max SPL 134 dB. With two 8-pin speakon compatible connectors. Ingress Protection IP55 rated. (Bose/QSC/AUDAC)

SITC (Supply, Installation, Testing and Commissioning)Ceiling flyable Horn-Loaded Cabinet with single 18” bass Driver, RMS power handling 800 Watts, Peak Power 1600 Watt rated at 8 Ohms. Sensitivity: 102 dB Max SPL : 131 dBs, Frequency Response : 37 Hz to 130 Hz . Ingress Protection IP55 rated. (Bose/QSC/AUDAC)

SITC (Supply, Installation, Testing and Commissioning) active 12" coaxial speaker with an integral 1" HF driver and powerful ferrite magnets, It is driven by a Class AB power amplifier with a power output of 1000W Peak and 250 RMS. The frequency response curve is 80Hz - 20kHz. The systems shall be Sound Pressure (Max. W/1m) 124 dbs., The systems desperation ratio 75° x 75°. The connections are performed using XLR speaker connectors, 15 mm Plywood cabinet. The monitor angle is 35°. Speaker stand be provided with it. (Bose/QSC/LD/AUDAC)

SITC active especially dependable 2-way speaker, The bass-reflex design is loaded with an 8" custom woofer and a 1“ silk dome tweeter with wave guide. The frequency response curve is 50 Hz - 20 kHz with dispersion of 60° and maximum sound- level pressure of 114 dbs. cabinet is made of 12mm MDF. (Bose/QSC/LD/AUDAC)

SITC (Supply, Installation, Testing and Commissioning)two way active cabinet with 12” Low/mid driver, 1” Compression Driver. RMS power 500 wall, peak power 1000 Watt, Coverage pattern of 90° x 50°, Max SPL 131 dB., frequency response 58 Hz - 20 kHz protection cerkit: over current, over voltage, and HF Driver. (Bose/QSC/LD/AUDAC)

4 Channel 750 Watt class D amplification , he Wave Dynamics™ DSP processor in combination with the 2.5” LCD display, it can be configured as Low / High & Band Pass and the 7-Band equalizer which has adjustable frequencies and Q-factor. It should be custom configured using the front panel of the amplifier, whereby access can be given on two different levels (User & Administrator) using password or USB-key protection. Frequency Response (± 3 dB) 20 Hz - 20 kHz, System integration is made easy using the RS-232 control port. (Audac / QSC / Bose)

4 Channel 500 Watt class D amplification , he Wave Dynamics™ DSP processor in combination with the 2.5” LCD display, it can be configured as Low / High & Band Pass and the 7-Band equalizer which has adjustable frequencies and Q-factor. It should be custom configured using the front panel of the amplifier, whereby access can be given on two different levels (User & Administrator) using password or USB-key protection. Frequency Response (± 3 dB) 20 Hz - 20 kHz, System integration is made easy using the RS-232 control port. (Audac / QSC / Bose)

SITC (Supply, Installation, Testing and Commissioning)two way active cabinet with 12” Low/mid driver, 1” Compression Driver. peak power 1000 Watt, Coverage pattern of 90° x 40°, Max SPL 119 dB., frequency response 80hz - 20khz protection cerkit: over current, over voltage, and HF Driver. (Bose/QSC/AUDAC/LD)

24 Channel analog mixer, 24 Mono input, four stereo inputs/returns with four groups (Yamaha, Sound craft, Toa)

Microphone type - Dynamic, polar pattern - cardioid, frequency response: 40 to 15 kHz, No phantom power required. With all mounting accessories. (SURE, AKG, Senniheiser, Beverdynemics)

Microphone type - Dynamic, polar pattern - half cardioid, frequency response: 20 to 20 kHz, condenser (electric bias, Phantom power require. (SURE, AKG, Senniheiser, Beverdynemics)

4 channel UHF Microphone, twin hand and twin lapple, digital display, 50Hz – 16 KHz, (Studio Master, Shure, AKG, Senniheiser)

18" Goose neck microphone with Wide dynamic range and frequency response 50 Hz to 16 kHz, with base support. (Studio Master, Shure, AKG, Senniheiser)

complete control form mobile device rack mounted Loudspeaker Management System (2) line inputs. (1) RTA Mic input, Input connection: (2) Female XLR line inputs. (1) Female XLR RTA Mic input,8-Band Parametric EQs, Type IV Dynamic Range 123 dB with transient material, A-weighted, 22kHz BW; 121 dB with transient material, unweight, 22kHz BW; 115 dB typical with program material, A-weighted, 22kHz BW (DBX, Yamaha, TOA)

MS Fabricated speaker mounting stand which take loaded up to 250 kg.

Cross sec area - 0.20 sqmm, number of strands: 25, conductor type - ATC, insulation type: HDPE, Shield: 93% ATC spiral, over al dia: 6.00 mm. (Krystal, MX, Balden, Bandridge or equivalent.)

2 Core speaker cable, ATC Copper conductor, PVC insulated, Cores twisted in circular form, Jacketed with PVC, CROSS SECTION AREA: 15 SQMM. (Krystal, MX, Balden, Bandridge or equivalent.)

Face plates with various connectors like, XLR, RCA, P38, HDMI, VGA etc to be mounted on stage for end user's comfort and easy installation. All gold platted terminals.

For all electronic products inter connections with all gold platted terminals inside rack as well as out side

CAT6A U/FTP Video & LAN Bulk Cable — Low Smoke & Halogen Free, 4 shielded twisted pairs (U/FTP) of 23AWG solid copper conductors are cabled together in an unshielded outer jacket. (Extron/Kramer/crestron)

Industrial 32 U Rack to incorporate all electronics with built in cooling fans, spike buster electrical proper connector, cable tray for proper cable laying. (JS Net or Equivalent)

Various size form 1.5 meter to 10 meter 2.0 version 19.8 GBPS Speed cables.

RGB liquid crystal shutter 3 LCD system, Native resolution WUXGA, Aspect Ratio 16:10, Throw ratio 1.44-2.33, 7000 lumens, Contrast ratio 50000:1, 4K enhanced, Inbuilt edge blending facility, curved surface enabled, include with Middle Throw Zoom Lens - ratio 1.0 - 1.5x, Throw Ratio (16:10): 3.32 - 5.06. (Projection Room distance form screen minimum 25 Running Mtr.) (Epson,barco, christie)

Projector stand for projector

HDBaseT receiver for 4K60Hz (4:2:0) HDMI, RS−232 and IR signals over twisted pair, Up to 70m (230ft) at 1080p, Up to 40m (130ft) at 4K@60Hz (4:2:0) (Extron/Kramer/crestron)

Compact 6–Input Presentation Switcher/Scalar with HDBaseT & HDMI Simultaneous Outputs, System Range — For the HDBT inputs and outputs, up to 70m (230ft), Max VGA Resolution — 1920 x 1200 @60Hz. (Extron/Kramer/crestron)

Providing and fixing 250" dignaol high gain fabric scren with require fabrication.

Providing and fixing motorized curtain with fabric of Rs 250 Running meter, horizontally two side slide with require fabrication

SITC Control channel Control channel 7 DM x 512 Ch., LED 54 x 5W 3 in 1 (JIA / STAN or equilent)

SITC 17+1 Metal Gobo, 14+1 Colors (Rainbow Effect), 8-Prism, Fat Beam, Wash, Frost, Focus, Gobo shake, Prism Rotation, Strobe, Dimmer, 16 DM X 512 channels, 10R 280W Lamp,life span 2000 h, total power 500W (JIA / STAN or equilent)

SITC (Supply, Installation, Testing and Commissioning) Smok machine 1500w with wireless control, coverage of 9 mtr, with 5 Ltr. Tank. (JIA / STAN or equilent)

SITC Light Controller Universal DMx 512 controller, able to control up to 40 lights, Each light with maximum of 36 channels in total, Can control up to 102 dimmer channel, 40 programs of chases, M Cahses, presets, each program (chase, M-chase, preset) up to 40 steps, Able to use 4 programs, 4 chases, 4 M chase, 4 Presets at same time, Can create New Unit internal library, Able to backup/update data to/from PC with RS232, MIDI Input/MIDI output Internal MIC or sound input. (JIA / STAN or equilent)

SITC Laser Show System Input AC220V 50/60Hz, Controls Sound, Auto, DMX, Laser Power 730mw (JIA / STAN or equilent)

SITC spot light Robust, pre-treated, fabricated housing with 7 tank rusto cleaning, black powder coat matt finish paint, Spot / Flood : Beam angle is adjusted by rotating of front / rear thermoplastic knob, Delivers uniform field across the entire beam from spot to flood focusing by using high quality German Fresnel lens, Control:Manual, DMX control through dimmer, Protection Rating:IP 20, Lamp power:2000W, Beam angle:6 - 58 Deg, Color Temperature:3200K, Lamp Base:G 38. (canara)

SITC Simple aluminium sheet metal, cylindrical construction, Natural cooling through punched slots on the housing, 1000W single ended ceramic type GX 16D base linear halogen lamp used, Beam angle: 10 Deg,Color Temperature:3200K, Protection Rating:IP 20, (canara or equilent)

SITC 24KV 6 channel Detects & protects against following power Conditions: Overvoltage, Undervoltage, Power Sags / Swells / Surges, Incorrect termination of 3 phase supplies (PS-180), Neutral Failure, Under Frequency, Over Frequency Protection Levels : Over voltage 245-275 VAC, Under voltage 170-220 VAC with Disable %-Over Frequency 50.5-55.0 hz with Disable, Under Frequency 45.5-49.5 hz with Disable, With Bypass switch, Input Output via High current terminals / CEE norm connectos, Available with Distribution Options / MCB-s. (Raytech or equilent)

The LCD 7254 is a superb featured unit with unique features. 18 channels of lighting can be grouped on a single fader allowing great ease and versatility of operation. (Raytech or equilent)

MS Fabricated mounting stand for lighting which take loaded up to 250 kg.

PANASONIC make 90W LINEAR HIGHBAY LIGHT PBYM08908

Providing and fixing fully perforated 12 MM MDF with 20% perforation of 9 mm dia fix on Gypsheera ™ 0.5x48 mm metal stud place at 600 mm center to center vertical and 1200 mm center to center horizontal fix with periphery channel of Gypsheera ™ 50 mm with require cavity and 12MM base frame to be fix on metal channel, cavity filled by 50 MM X 1000 GSM synthetic wool, complete systems cover with acoustic fabric. The peripheral and intermediate members and the suspended angles shall be designed for each area and the ceiling detailed drawing shall be submitted to Client/Architect in charge for approval prior to fabrication. Measurement will be consider plan area.

Providing and fixing natural wood stage flooring 16 x 915 x 125 mm with tongue and groove fixing on 50 x 50 mm natural wood 600 x 600 gridwoork along with the fixing 12 mm MR plywood on fabricated frame work with require accessories, hardware and adhesive, cavity should be filled by 24/50 mm glass wool than apply wood protection mono coat on wooden plank with require sealer. The peripheral and intermediate members and the suspended angles shall be designed for each area and the ceiling detailed drawing shall be submitted to Client/Architect in charge for approval prior to fabrication. Measurement will be consider plan area.

Providing and fixing floor carpet 100% polyproplin loop pile of 5 x 500 x 500 mm with backing structure glass rainforsed PVC using with SR adhesive, eractig, and furnising. total waight 4300 gm per sqm., pile thickness 3 mm, as per under direction by client / architect in charge with prior approval. (UNITEX, SOLARBRITE, GREENIELD)

Providing and fixing over all 56 mm Acoustic door with acoustic door seal using with 100 x 150 mm frame surrounded 4 mm neoprine strip, wooden beading, door make by 12 mm plywood and 12 mm board with require perforation with infill of acoustic wool and 6 mm flexibale acoustic sheet, one side finish of interior surface and another side of laminet finish with essenisal hardwae like doo handle, door spring, door stop, lathe lock, etc as per under direction by client / architect in charge with prior approval.

Providing and installing chair, Seat and back of 20” x 20” x 1.6 SWG square pipe frame, 12” x 3” M.S. Flat strip, P U molding 45 to 50 density, 12” x 3” M.S. Flat strip, In OE -108 3 mm abs plastic tray, Rs. 230/- per meter cloths, stand of 1.6 SWG M.S. Sheet, 30 density foam with side support, handle (PPCP), 2 nos. of anchor fasteners 10 mm x 100 mm in floor fitting with 100 x 10 ms flat base, MECHANISM of 14 SWG M.S. Seat and Back bracket, 20 x 40 mm M.S. Pipe frame support, 16 SWG side support, Rolling sliding push back mechanism spring, Asian / Burger Paint colour. ( Godrej, littlenap or equilent)

Providing material and labour for fixing 35mm thick solid core flush type door shutter (non decorative) of approved make and as per approved sample (Battens should be chemically treated & kiln seasoned & binding agent should be phenol phormaldihide) and of required size, as per approved drawing, design and direction. The rate shall also include external lipping of maximum size 10 mm X 42 mm thickness for single shutter and 25 mm x 42mm thickness for double shutter of seasoned teak wood equivalent to best quality 1st class teak all around and 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ oil and water finished polishing or lacquer polishing to lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items.

Providing material and labour for laying Ceramic tiles 6mm thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white cement, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge.

Providing material and labour for laying Ceramic tiles 6mm thick in skrting, risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge.

Providing material and labour for fixing 6mm thick frame less mirror of approve make in any shape and sizes as per drawing. Mirror shall be fixed on 6mm thick cement bonded particle board (Bison panel) backing. Cement bonded particle board shall be fixed to wall with approved SS 304 fastener. All edges of glass shall be sharp grinded, cute corner and polished. Glass shall be fixed with silicon sealant/ 3M tape etc complete at all floors/ all levels/ all heights as directed by engineer in charge. Installed area of mirror shall be considered for payment without wastage.

Providing material and labour for laying 25mm thick (average) polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including curing, rubbing and polishing at all floors any heights, any lead and lift in any shape and pattern etc complete as directed by Engineer In charge.

Providing material and labour for fixing hydraulic rack and pinion door closer with standard arm (Silver finish) with screws to pivoted/ hinged door of approved make for specified door width with minimum one year guarantee. All adjustment screws face fixed. Rate shall be inclusive of fixing with using the template as per manufacturer’s specification & maintain in good working condition until defect liability period. The door closer shall conform to EN 1154 standard. a) with standard/ hold open arm with two independent closing valves and latching speed adjustable by arm without mounting back plate, Closing force complying with EN 1154 2 - 4 for up to 1100 mm door shutter width

" Magic MMPL-70020 Durian Make Staff chair with BIFMA COMPLY and following features: 360 Degree Swivel for ease of motion, Tilt Tension Adjustment, Pneumatic height Adustment, Tilt Lock, Maximum Height: 920 mm, Minimum Height : 820 mm, Outer Dimension: 650mm, Seat Deapth: 450 mm, Compoment & Material: Mesh back with Curved Design, Fabric Upholstred soft seat Cushion, Componet detail: Fixed Arm, Naylon Base & Castors, ERGONOMICS FEATURES: Ergonomically Design with flexi back comfort.. DURIAN'S FIVE YEARS LIMITED WARRANTY

" JORDON - MMPL-70024 Durian Make M/B Mesh chair with BIFMA COMPLY and following features: 360 Degree Swivel for ease of motion, Tilt Tension Adjustment, Pneumatic height Adustment, ARMS height Adjustment, Synhrco-Tilt Locking, Seat Glide Mechanism, Maximum Height: 1040 mm, Minimum Height : 940 mm, Outer Dimension: 610mm, Seat Deapth: 470 mm, Compoment & Material: Breathable Mesh back with Cushoined Fabric , Adjustable Lumbar Support & Armrest in PU, Componet detail:PU Adjustable Handles, Chrome Base & Naylon Castors, ERGONOMICS FEATURES: Adjustable Lumbar Support on the Back, Any Position Locking Mechanism, Adjustable Armrest with any Position Lock... DURIAN'S FIVE YEARS LIMITED WARRANTY

" JORDON - MMPL-70024 Durian Make H/B Mesh chair with BIFMA COMPLY and following features: 360 Degree Swivel for ease of motion, Tilt Tension Adjustment, Pneumatic height Adustment, ARMS height Adjustment, Synhrco-Tilt Locking, Seat Glide Mechanism, Maximum Height: 1240 mm, Minimum Height : 1140 mm, Outer Dimension: 640mm, Seat Deapth: 480 mm, Compoment & Material: Breathable Mesh back with Cushoined Fabric , Adjustable Lumbar Support & Armrest in PU, Componet detail:PU Adjustable Handles, Chrome Base & Naylon Castors, ERGONOMICS FEATURES: Adjustable Lumbar Support on the Back, Any Position Locking Mechanism, Adjustable Armrest with any Position Lock... DURIAN'S FIVE YEARS LIMITED WARRANTY

"SPARK" Visitor Chair in Leatherlite finish Made up from CUT Form & Leathrite, Chrome Four Legs Base with Seat Depth 430 MM, Seat & Back Cushion with extra Padded Support.. Durian Five year Limited Warranty

Stainless Steel Dustbin (HOTC) (Steel Dusbin Pedal) 10 litres weight of dustbin:1200 grams. Lid: foot pedal operated gripping provision frontal

Dustbin Mterial: LLDPE with 100 litres Bin Capacity. Colour Green & Blue. Lid: Swing type

ABC Type fire extinguisher cap. 9 Kg filled with Mono Ammonium Phosphate powder 50 % confirms to IS 14609, stored pressure type, UGTS pressure gauge, gross weight 13.3 kg, empty weight 4.3 kg, can height 575 mm, diameter 180+- 10mm, discharge time 31 sec, controllable dischage mechanism, jet range 6 meters, average discharge is 90%, applicable on class A,B & C and electrically started fire, A Rating #A, B Ratinf 21B, Can construction: Deep drawn & CO2 mig welded, EPDM rubber hose with both end aluminium clamped , internal coating- epoxy powder coating, external coating- pure polyster powder coating (UV resistant), brass forged valves with safety pin is of SS material, Sheet metal thickness:2.0 mm, ISI Approved IS 15683:2006

SRISHTI ENTERPRISES

Tirupati Sarjan Limited