SPECIAL REPAIRS TO JCOS MARRIED ACCOMMODATION BUILDING NO P 102 AND P 103 WING V AT ARTY CENTRE UNDER GE NASIK ROAD CAMP

Demolition of concrete (unreinforced) of any description and in any position not otherwise specifically provided for.

M & L for Providing, cement concrete type B1 1:2:4 (20mm graded aggregate) in roof kerbs ,padding concrete or mud stops, rounded or chamfered on edges.

M&L for rendering 10 mm thick cement plaster in CM 1:4 on RCC/concrete roof/terrace surfaces mixed with water proofing liquid complete all as specified and as directed. Note: Water Proofing liquid shall be measured and paid separately.

M & L for waterproofing on roof including flashing and junctions of parapet,kerb,wall etc as undere-: (a) Laying a layer of APP based polymeric membrane,3mm thick(minimum),weighing not less than 3.60kg/sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160gms/sqm) shall be applied over compatible primer(oil based) at 0.2 litre/sqm of density at 25 degree centigrade 0.87-0.89 kg/litre and viscosity 70-160cps or cold sticker,application of APP modified membrane shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100mm on the longitudinal direction. (b) APP membrane,bitumastic Primer and aluminium paint shall be of same brand. (c) For vertical surfaces of parapet,wall etc. app membrane shall be tucked into groove and sealed with silicon sealant(full width/depth of groove) i.e. "Dowsil 789 weatherproof silicon sealant" using gun. (d) Applying solar reflective bitumastic aluminium paint at the rate 0.15Kg per sqm over exposed app membrane surfaces.

Supply only liquid water proofing compound

Dismantling/Disconnecting of water tanks (RCC hume Pipe/PVC) including disconnecting all connections etc 1000 ltrs capacity. complete for following capacity of tanks .

Refixing the old rotational moulded polythylene water storage tank 1000 ltrs capacity (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball valve high pressure with polythene float and fly nut, 20mm bore complete for following capacity of tanks.

S&F new rotational moulded polythylene water storage tank 1000 ltrs capacity (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball brass valve high pressure with polythene float and fly nut, 20mm bore complete for following capacity of tanks.

S&F in repairs 20mm bore CPVC gate valves screwd both ends for CPVC pipes complete all as specified and directed.

S&F in repairs 25mm bore CPVC gate valves screwd both ends for CPVC pipes complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

S & F 16mm dia CPVC pipes with all fittings SDR 11 & Plain CPVC SDR 11 fixed to walls and ceilings with adequate nos of clamps or laid in floor/walls including cutting chases in stone,concrete block or slab wall pinning in making good to facing where ever required to the sufraces for concelled water supply including other fittings required for fixing of sanitary/plumbing items complete all as specified and as directed. (Note : No extra payment shall be made for cutting chases )

S & F 20mm dia CPVC pipes with all fittings SDR 11 & Plain CPVC SDR 11 fixed to walls and ceilings with adequate nos of clamps or laid in floors including cutting chases in stone,concrete block or slab wall pinning in making good to facing where ever required to the sufraces for concelled water supply any other fittings required for fixing of sanitary/plumbing items complete all as specified and as directed. (Note : No extra payment shall be made for cutting chases )

S & F 25mm dia CPVC pipes with all fittings SDR 11 & Plain CPVC SDR 11 fixed to walls and ceilings with adequate nos of clamps or laid in floors including cutting chases in stone,concrete block or slab wall pinning in making good to facing where ever required to the sufraces for concelled water supplyand any other fittings required for fixing of sanitary/plumbing items complete all as specified and as directed. (Note : No extra payment shall be made for cutting chases )

S & F 16mm dia CPVC pipes outer diameter Brass Elbow complete all as specified and as directed.

S & F 16mm dia CPVC pipes outer diameter Brass Tee/nipple/reducer/socket/union complete all as specified and as directed.

S & F 16mm dia CPVC pipes outer diameter Male Brass Threaded Adaptor (MTA/ MBTA) ) complete all as specified and as directed.

S & F 16mm dia CPVC pipes outer diameter Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and as directed.

S & F 16mm dia CPVC pipes outer diameter Tank Adaptor complete all as specified and as directed.

S & F 20mm dia CPVC pipes outer diameter Brass Elbow complete all as specified and as directed.

S & F 20mm dia CPVC pipes outer diameter Brass Tee/nipple/reducer/socket/union complete all as specified and as directed.

S & F 20mm dia CPVC pipes outer diameter Male Brass Threaded Adaptor (MTA/ MBTA) ) complete all as specified and as directed.

S & F 20mm dia CPVC pipes outer diameter Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and as directed.

S & F 20mm dia CPVC pipes outer diameter Tank Adaptor complete all as specified and as directed.

S & F 25mm dia CPVC pipes outer diameter Brass Elbow complete all as specified and as directed.

S & F 25mm dia CPVC pipes outer diameter Brass Tee/nipple/reducer/socket/union complete all as specified and as directed.

S & F 25mm dia CPVC pipes outer diameter Male Brass Threaded Adaptor (MTA/ MBTA) ) complete all as specified and as directed.

S & F 25mm dia CPVC pipes outer diameter Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and as directed.

S & F 25mm dia CPVC pipes outer diameter Tank Adaptor complete all as specified and as directed.

Taking down chowkhats or frames with shutters(without taking off shutters from the frame) exc 1.5 sqm but n. exc 4 sqm each .

Taking down chowkat or frames with shutters (without taking off shutters from the frame) but n exc. 1.5 Sqm

Taking down MS window/ventilators frames with shutters of any size and any description. Note:work is to be executed for high rise bldgs.

S&F powder coated of powder coating 50 micron aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality) for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and including 4.80 mm thick figured glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading ,clips,frame made with aluminium section as appended below- (i) Window frame 92x38 mmx2.00mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 20mmx39mmx2.00mm thick and over. (iii)Aluminium beading -0.7mm thick.(iv)Stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed in aluminium window or along with F/Y section fixed with aluminium wire staples complete.(v) Aluminium fittings such as aluminium suitable handle with auto interlock cap with suitable size. (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed by engr-in-charge. Note : Rate for glass and wire shall not be paid separately.

S&F for powder coated aluminium ventilator with frame not less than 0.55Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 4mm thick frosted glass and outer side fixed with stainless steel wire mesh, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed.

M & L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50 x100 mm (single) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position complete as per direction of Engineer-in-Charge.

M & L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm (double rebated)comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position complete as per direction of Engineer-in-Charge

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Prelaminated solid decorative type flush door shutter(design) CNC routed decorative patterns on one or both faces,design as per approved drawing/pattern,depth of design: 3-6 mm,provides modern and aesthetic look of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws all as per direction of Engineer -In- Charge.

S & F 125mm SS butt hinges,heavy duty,satin finish,complete with SS screw and all works as a specified and direction.

S & F 150mm SS door handles,satin finish,complete with SS screw and all works as a specified and direction.

S & F 250mm stainless steel sliding door bolt heavy duty,corrosion resistant,satin/matt finish complete with matching SS screw ,receiver plate ,fixing accessories,fixed firmly in position including drilling works as a specified and direction.

S & F 200mm stainless stee tower bolt,satin finish,complete with SS screw and all works as a specified and direction.

S & F floor door stopper of aluminium alloy body and tongue,140 mm long anodised,with hard drawn steel spring,fixed in floor

Dismantling wrought iron or mild steel any description such as steel gate,steel frame works,purlins,rafter,railings,balusters and window guard bars and directed by engr-in-charge. Note.work is to be executed at any height and situation.

S & F framed work as in grill,doors or gates of angle or other section with gusset plates,braces,etc. complete,drilled for fixing of steel sheeting or other coverings,doors,etc to be prepared for hanging or sliding with and inlcluding either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering,running rails and guides) and hanging;also fastening and fixing Fe.290.Gde-E-165 complete as specified .

S&F for painting with two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces exc 10cm width or girth including preparation of new steel surfacesall as specified and directed by EIC.

Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons and removing the debris out of MOD landetc complete all as specified and as as directed.

M&L for non skid joint free ceramic tiles (of size 7 to 8mm thick (coloured) (Square/rectangular) area of each tile exc 0.06 but n exc 0.18 sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles in vertical surface of size (300X 450X 8-300 x 600 x 8)mm thick of different shade colour and pattern as approved, over and including 10 mm thick rendering in CM 1:4 as backing coat finished to receive wall tiles, set and jointed in neat cement slurry and pointed in white or coloured cement to match to match complete all as directed and specified.

M & L for 8-9 mm thick Vitrified Ceramic tile(sattin matt/glossy) finished (600x600-600x1200)mm as in flooring,circular verandah flooring laid in any shape/pattern over and including 15mm thick screed in CM 1:6 as floors,set and jointed in fill up EPOXY TILE GROUT to match the shade of the tile complete all as specified and directed.

M & L for 8-9 thick Vitrified ceramic tile(sattin matt/glossy) finished (600x600-600x1200)mm as in skirting for floor /circular verandah etc laid in any shape/pattern over and including 10mm thick rendering in CM 1:4 as skirting,set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the shade of the tile complete all as specified and directed.

M & L for 40 mm thick PCC 1:2:4 type B0 (using 12.5 mm stone aggregate) as in levelling course to flooring.

M & L for supplying ,cutting ,machine polishing, and fixing of 18-20 mm thick ''Z black Granite stone'' in steps, jambs, pillars, window cills, cooking platforms,slab in required size ,with mirror polish finish, laid over 20 mm thick cement morter (1:4)bed ,joint filled with matching pigment slurry/epoxy grout,including edge polishing,curing,cleaning,and finishing as a complete specified

M&L for hand cut cudappa stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete Note: screed bed layer measured seperately complete all as specifed and directed

M & L for Polished Kota Stone Skirting of approved height and shade (first quality) 20mm thickness and 12 mm thick 1:3 cm screed bed,nosing rounded/chamfered and edges dressed and joints filled with matching cement slurry, complete grinding and polishing to mirror finish complete specified and directed EIC.

M & L for Polished Kota Stone treads,risers and floors (first quality) 20mm thickness and 20 mm thick 1:4 cm screed bed,nosing rounded/chamfered and edges dressed and joints filled with matching cement slurry, complete grinding and polishing to mirror finish as a complete specified and directed EIC.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base,plinth protection including making joint at every 3mtr interval and and corner finished even and fair and laid in alternate bays complete all as specified and directed.

Rounding to edges of stone slabs one edge such as in steps cooking platform and other similar work

M&L for fixing in repair 25 mm matt finish Stainless steel SS-304 grade curtain rod best quality as approved by Engr-in-charge

M&L for fixing in repair Stainless steel ornamental piece with bore dia of 25 mm for free end of curtain rod .

M&L for fixing in repair Stainless steel projecting bracket to support curtain rod of size 25mm.

S & F in repair CP, soap dish complete all as specified and as directed by Engr-in-Charge.

M&L for special treatment to sunken portion two coats betumastic oils base primer with 10mm thick plaster in CM 1:4 by using Ditachment DM 1% by weight of cement and surface made smooth after curing period two coat of Ditachment DS shall be applied @2.50 Kg/Sm. The paste like consistancy like is made by using 2.5 Kg of Ditachment DS powder in one litre of admixture (The admixture is made by dissolving 1 part by volume of Nafufill SBR & 4 part by volume of water). After 7 days curing, testing shall be done by flooring for 72 hours. Finally protective plaster coat of 10mm thick in CM 1:4 shall done by using Putz Ditachment 1% by weight of cement over layer of Detachment DS. All joints of CI Pipe, Nahani trap, WC connection etc. shall be filled by mixture of cement, fine sand and 10% Nafufill SBR by weight of cement 32mm dia 450mm long GI Spout light grade shall be provided in all sunken slabs to drain off water

M and L for repair to broken edges of RCC chajjas,roof projections,fins,facia and similar works by dismantling of loose and damaged/disintegrated portion of edges with any cross sectional area with cement mortar 1:4 or cement concrete 1:1.5:3 type A0 and chicken wire mesh with nails to hold fresh mortar and concrete including necessary formwork and scaffolding for work upto 2 storey buildings and finishing the surfaces to the entire satisfaction of engr-in-charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed.

M and L for brick work fly ash brick with old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specifed and directed

S&F in repair 15mm dia brass chromium plated Central Hole Basin Mixer single lever tall boy with 150mm extension body fixed spout without popup waste system with 600mm long braided hoses for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make Jaguar Cat Part No: FLR-5005NB or equivalent in kohlar, grohe and Roca

S & F in repair for 15 mm bore, fancy type, Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange Make Jaguar Cat Part No: FLR-5281N, Hand shower HSH 1715, flexible tube SHA-549D12 or equivalent in kohlar, grohe and Roca.

S&F in repairs 15mm bore CP Sink mixer with regular swinging spout (Wall mounted model) with connecting legs and wall flenge complete all as specified and as directed. Make Jaquar Cat Part No. FLR-5309N or equivalent in kohlar, grohe and Roca.

S & F in repair 15 mm bore, fancy type, bib taps, long body, cast copper alloy, 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge.

S & F in repairs Brass chromium plated shower rose 125mm size with swivel joint, including fixing to steel pipe or union 15mm bore.

S&F in repair Health Faucet (ABS Body) with 1.20 M Long PVC Tube and wall Hook screwed down to GI pipe or union/angle valve complete all as specified and directed by Engr-in-charge

S & F in repair 15 mm bore, fancy type, angular stop valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge.

S & F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges.

S & F in repairs 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repairs 8mm thick glass shelf "Corner" type size 300mm x300mm including necessary brackets front edge of glass rounded and woulded with CP railing complete, fixed in repairs .

S & F in repairs Sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 mm x 420mm bowl size 410mm x 330mm x 160mm.

S & F 32 mm thick Waste pipe for sink made for unplasticized polyvinyl chloride(uPVC) complete with all necessary fittingssuch as a bends,tees,couplers,rubber washer joints,clamps and fasteners.

M and L for Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed.

S&F for 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed..

S&F in repair fancy type Toilet paper holder, steel chromium plated approximate size 140X140X50mm complete all as specified and as directed.

S&F in repair 15mm dia brass chromium plated two way bib cock with long flange screwed down for 15 mm dia bore GI Pipe complete all as specified and directed.

S&F in repairs glazed earthen ware viterous china wash down water closet (Anglo indians pedestal pattern) white coloured with and including plastic water closed seat, white, closed pattern with recessed bottom, and cover and mild steel chromium plated hinging device etc complete all as directed.

S&F in repairs glazed earthen ware viterous china wash basin with full pedestal white coloured (flat back or angle back type), size 550x400 mm and including CI brackets, outlet of 32 mm bore HDPE outlet pipe with necessary fittings, 32 mm bore brass CP waste couplings and CP Brass bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed etc complete all as directed.

S & F in repairs kitchen plate rack made out of stainless steel 0.8mm thick complete of size not less than 750x750x200mm, duly assembled and fixed to wall with wall screws / fasterners all as specified and directed.

Taking down 100/75 mm dia PVC/CI sand cast soil, waste and vent pipes, in any length with or without etc in any position

S & F PVC (SWR) bends, any radius 75 mm bore with oval access door complete all as specified and directed.

S & F PVC (SWR) bends, any radius 110 mm bore with oval access door complete all as specified and directed.

S&F of PVC(SWR) branch piece,single(single Y) 110 mm dia equal or unequal

S & F PVC (SWR) branch piece, double (double Y) equal or unequal 110 mm bore with access door all as specified and directed.

S & F PVC gully trap 125/110 mm setting and jointing in solven cement. Complete all as specified and as directed.

S&F of PVC(SWR) vent cowl of 75/ 110mm bore

S and F 110mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

S and F 75 mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

Demolition reinforced cement concrete tank capacity n.exc 12000 Ltr and removing the debris out of MOD land.

M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint , girth or width exc 10cm complete all as specified and directed

M & L for painting with one coats of synthetic enamel paint on old painted wooden surfaces exc 10cm width or girth including preparation of wooden surfaces all as specified and directed by EIC.

Taking down cement plaster on brick or stone wall or ceiling etc including raking out joints hacking for keys scrubbing down with water etc.Note:For multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height.

M & L 10 mm thick rendering in CM 1:6 on brick work or stone masonry/concrete /RCC surfaces rendering is to be finidhed even and smooth without using extra cement complete all as spd and directed at any height.

M&L for rendering 15mm thick in CM 1:4 on brick work or stone masonry/concrete /RCC surfaces rendering is to be finidhed even and smooth without using extra cement complete all as spd and directed at any height.

M&L for rendering 5mm thick in cement mortor 1 :3 as in ceiling plaster on concrete surfaces, rendering is to be finidhed even and smooth without using extra cement complete all as spd and directed at any height. complete all as specified and as directed.

M & L for Plastering on walls in cement mortar 1:4 in patches not exc. 3 Sqm on the buildings upto four storied any description including finishing the surface to match existing surfaces. Note:For multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height.

M & L for Exterior grade acrylic emulsion paint on new as well as old/existing exterior surfaces(wall/ceiling) after proper surface preparation,complete in all respects,as per manufacturers specifications and directions of EIC. Old Surface preparation (a) scraping, wire brushing and removal of loose/flaking paint (b) cleaning of surface to remove dust,dirt,algae,fungus & efflorescence (c) washing with clean water and allowing surface to dry (d) repair of cracks with approved exterior crack filler / wall putty (e)Application of fungicidal / algicidal wash where required. new surface preparation : New plaster to be cleaned of dust ,dirt and loose particles primer / sealer : one coat of exterior wall sealer / primer suitable for old surfaces and primer shade compatible with finish coat. Paint Application (a) Two or more coats of exterior acrylic emulsion paint of approved makes & shade (b) paint to be applied by brush / roller / spray (c) Uniform shade, smooth and even finish (d) Drying time between coats as per manufacturers recommendation. (Makes : Asian paint(Apex)/Nerolac/Dulux) Note:For multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height.

M & L for Interior grade acrylic emulsion paint on new as well as old/existing (wall/ceiling) surfaces after proper surface preparation,complete in all respects,as per manufacturers specifications and directions of EIC. Old Surface preparation (a) Scraping and complete removal of loose/flaking paint/putty (b) cleaning of surfaces, removal of oil/grease stains (c) minor crack filling with approved filler new surface preparation : New plaster to be cleaned of dust ,dirt and loose particles primer / sealer : two coat of interior wall sealer / primer suitable for old surfaces and primer shade compatible with finish coat. putty : Acrylic wall putty in two coat (1.5 mm thickness per coat) Paint Application (a) Two or more coats of interior acrylic emulsion paint of approved makes & shade (b) paint to be applied by brush / roller / spray (c) Uniform shade, smooth matt / satin finish (d) Drying time between coats as per manufacturers recommendation. (Makes : Asian paint(Royale/Tractor)/Nerolac/Dulux) Note:For multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height.

Dismantling wall and ceiling boards(fibre,pulp,insulation,etc.) or insulation boards/slabs/blankets,kitchen cabinets board any thickness,including cover fillets,frame etc.

M & L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 60x30(single/double rebated) mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.over and including M.S. hold fast/ lugs or SS dash fasteners.

S&F LDPE pipe 40mm bore fixed to wall/ceiling with bends/elbow complete all as specified.

Supply for Pipe Supporting Clamping - Single Pipe of dia 20 mm (3/4") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 100 mm (4"): Pipe Support Clamping made of: 1. Mono Bracket for 20 mm (3/4") pipe having Wall Distance 100 mm (4") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 20 mm (3/4") pipe, Wall distance 75 mm (3") - 1 Nos. 2. U Bol Rubber Sleeve mounted for 20 mm (3/4") GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Pune Zone Technical Drawing (TD) of Factory Made Pipe Supporting System : CEPZ/2023/TD/03 and CEPZ/2024/01. Make : Shaivi or equivalent as approved by GE.

Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed.

S & F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum in hard /dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface

M&L cement concrete type C-2 1:4:8 ( 40 mm graded aggregate) as in foundation,post hole filling and mass concrete.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand,as a complete specified and directed.

M and L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in sub base floor finised etc complete all as specified and as directed.

S & F steel work in trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.4923; 19979 grade YSt.-210 over

Taking down carefully copper/aluminium point wiring complete alongwith casing patti/ PVC conduit removing materials to store and making good to disturb surfaces of wall/floors etc as specified & directed.

M&L Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.2mm thick, with modular cover plate with frame of adequate required modules for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end complete all as specified and directed for the following:- Note:- Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

(a) One light point/ fan point controlled by one, one way swtich.

(b) One 5 Amp 3 pin socket outlet point on same board with other switches including earth wire as specified.

(c) All as per ser item No. 127.01 herein before but with 2.5 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 6 pin socket outlet point including PVC cable 2.5 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including boards for mounting purposes.

(d) All as per ser item No. 127.01 here in before but on independent board for one 3 pin socket outlet, 5 Amps.

(e) All as per ser item No. 127.01 here in before but one light point controlled by 2 way switches.

(f) All as per ser item No. 127.01 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent.

Supply and fixing switch modular type 6 Amps one way, 1 module, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing switch modular type 16 Amps one way AC 230 Volts.

Supply and fixingof switch modular type 6 Amps two way, 1 module, AC 230 Volts, LED based indicator, shrouded terminal, ISI marked complete all as specified and directed.

Supply and fixing modular type bell push 6 Amps, AC 230 Volts.

Supply and fixing modular type socket 6 Amps 3 pin round socket with child safety shutter (ISI marke), AC 230 Volts, shrouded terminals, smooth plug removal and insertion complete all as specified and directed.

Supply and fixing modular type socket 6/16 Amps 2/3 pin combined, AC 230 Volts.

Supply and fixing modular type fan regulator, AC 230 Volts.

Supply and fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fix ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish.

Supply and fixing in replacement of LED 20 Watt LED decorative box type with driver, holder including LED tube lights connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in replacement of LED 10 Watt LED light fitting mirror type with high output diffuser, 2 feet 10 watt, 230volts AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose.

Supply and fixing bell, AC, 230 volts, single phase complete all as specified and directed.

Supply and fixing in replacement of sheet metal enclosures with plug socket single pole and neutral with two pin and earth plug and with one MCB of 20 Amps (SP) complete all as specified.

Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 10 Sqmm drawn through in and including PVC concealed conduit including 10 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed.

Supply and fixing in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including PVC concealed conduit including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Two runs of cables and one run of continuous earting cable drawn in concealed conduit will be measured as one length of sub main. (ii) PVC conduit heavy duty and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for sinking for boxes and making good to wall, floors etc.

Supply and fixing in replacement Distribution Board, TPN Vertical (MCCB Incomer) IP43 protection Double Door, 4 way, mechanical impact strength IK 09, suitable for MCCB 63 Amps as Incomer (frame 1) of Cat Ref No 811888 of Indo Asian or equivalent complete with 200 Amps rated busbar all as specified and directed.

Supply and fixing in replacement distribution board sheet metal enlosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways all as specified & directed.

Supply and fixing in replacement 3 Pole MCCB 63 Amp, 50 Hz, 415 V, fixed type, breaking capacity 16 KA.

Supply and fixing in replacement of MCB DP/SPN 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

Supply and fixing in replacement of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

Supply and fixing in replacement of 35 Watt LED street light fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. , including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of LED bulkhead 10 watt 220 volts AC complete with drivers, clamps of CP No HLBH-15-10-CW-INV Halonix or equivalent and complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Material and labour for in replacement of MS box of size 160x120x30 cm depth, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of MCCB, DB's, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealled and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box with MCCB DB's and electric meters and refixing the same MCCB, DB's and electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing completed all as directed by Engr-in-Charge. Note : (a) Any plastering work involved while taking out old UNSV meter box and refixing the new meter box is deem to be included in this rate. (b) PVC flexible conduit required within the meter boxes is deemed to be included in this item rates.

Note :- Schedule of Credit of Amount Rs 161800.00 shall be deducted from total amount.

Please Enable Macros to View BoQ information