PAINTING AND POLISHING AND CERTAIN REPAIR OF STEEL

Amount

M&L for preparation of old painted iron & steel surfaces (externally and internally complete) of following furniture items by scraping & rubbing down with grinder machine, removing dents and scratches if any filling the same with paste filler and applying two coat of synthetic enamel paint by spray equipment of 1st Grade quality,(Shade/colour shall be approved by engr-in charge) complete all as specified and directed .

Almirah largewith shelves steel.

Almirah med/small steel with shelves.

Locker bedside steel.

Book shelf open large steel steel.

Table with drawer 900mmx600mmx760mm (steel)

Table steel 900mmx600mmx760mm

Table steel 900mmx900mmx760mm

Table office clk steel.

Table office offr steel.

Chair CB steel with arms.

Table bed side (MAP)

Bed Hard (MAP)

Chair executive revolving high /medium/low back, chair computer, chair writing, chair conference, chair visitor etc.( FD/MAP/ TP)

Rack 6 tier

Rack pigeon hole

Almirah glazed large steel.

Teapoy Verandah Steel

Table computer MAP/TP

M&L for preparation of old painted iron & steel surfaces (externally and internally complete) of following furniture items (TP) by scraping & rubbing down with grinder machine, removing dents and scratches, if any, filling the same with paste filler and applying two coat of hammerton powder coating paint externally and two coats of synthetic enamelled paint internally of ist grade quality by spray equipment (Shade/colour shall be approved by engr-in charge) complete all as specified and directed .

Almirah large1/2H hanging 1/2Shelf steel.

Almirah large steel with shelves

Book case steel

Almirah med/small steel.

M & L for preparation of old wooden polished surfaces by rubbing down the old polish from the wooden surfaces including the new fixed wooden parts with grinder machine, removing pluck marks with wooden scraper, cleaning of dirt and stopping holes by filling putty by adding colour of required quantity to obtain the desired colour, wiping old superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying French polish till glossy finish is achieved complete all as specified and directed .

Bed hard

Chair dinning cushioned

Chair dinning MAP (JCO/OR)

Chair dinning

Chair writing

Chair easy

Stool dressing CB/MAP

Table peg

Teapoy

Table centre

Table 900mmx600mm without drawer

Table 900mmx600mm with drawer

Table 900mmx900mm

Table dinning 1200mmx900mm

Table dinning 6 pers

Table dinning 8 pers

Table bed side

Hat stand with mirror

Bin soiled linen FD-244

Table dressing gents w/mirror

Table dressing ladies w/ mirror

Side board

Table writing

Book Case(W)

Sofa set 5 seater FD-281/373

Sofa set 4seater FD-281

Sofa set 5 seater FD-258

Table office offr (W)

Table 5'x2'-10"

Table office clk(w)

M&L for repair Almirah steel large/Almirah steel 1/2H 1/2shelf by replacing the following unserviceable parts with approved ones complete all as per the drawings and as directed. (DRG NO. FD-1031/ 67(M))/FD/E6/MAP/18)

MS lock 6 lever with duplicate key.

Stainless steel handle 150mm long.

Complete internal locking device duly painted with one coat of red oxide primer.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer.

Shelf made out of 1mm thick MS sheet duly painted with one coat of red oxide primer.

Cover for locking device made out of 1mm thick MS sheet duly painted with one coat of red oxide primer. Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

M&L for repair Almirah medium/small steel by replacing the following unserviceable parts with approved ones complete all as per the drawings and as directed. (DRG NO. FD-1032/243/67M))

MS lock 6 lever with duplicate key.

Stainless steel handle 150mm long.

Complete internal locking device duly painted with one coat of red oxide primer.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

Shelf made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

Cover for locking device made out of 1mm thick MS sheet duly painted with one coat of red oxide primer. Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

M&L for repair locker steel by replecing the following parts with approved ones complete all as per drawing and as directed . (DRG NO. FD-257/1029)

MS cromium plated hasp and staple 75mm long.

MS cromium plated handle 100mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

M&L for repair book case steel by replacing the following parts with approved ones complete all as per the drawings and as directed. (DRG NO. FD-1028/TP)

SS handle100mm long.

Lock of suitable size with duplicate key to lock all four shutter with one key .

Pane glass 3 mm thick of suitable size.

M&L for repair Teapoy verandah by replacing the top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF 11) one side with approved shade and balancing white on other side duly teakwood beading 4x18/19mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of french polish complete all as per the drawings and as directed. (DRG NO. FD-255 /208/ 35 )

M&L for repair table steel with /without drawer (900mmx600mmx760mm) by replacing the following parts with approved ones as mentioned below complete all as per the drawings and as directed. (DRG NO. FD-1007/1008 )

Top made out of 18/19mm thick pre-laminated MDF board (exterior gde) one side with approved shade and balancing white on other side duly teakwood beading 4x18/19mm all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of french polish

hard rubber toe of suitable size

Removing old u/s top from table 900mmx900mm steel and S&F new top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF 11) one side with approved shade and balancing white lamination on other side duly teakwood beading 4x18/19mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of french polish. Rest all as per the drawings and as directed.(FD-1009)

S&F Hard rubber toe for table 900mmx900mm of approved quality and suitable size complete all as specified and directed.

M&L for repair table office clerks steel by replacing the following parts with approved ones complete all as per the drawings and as directed. (DRG NO. FD-1004/381/307/84(M)).

MS lock of suitable size with duplicate key

Table Top made out of 18/19mm thick pre-laminated MDF board exterior gde ( Designation PLMDF 11) one side with approved shade and balancing white lamination on other side duly teakwood beading 4x18/19mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of french polish

S& F Hard rubber toe of suitable size.

M&L for repair table office officer steel by replacing the following parts with approved ones complete all as per drawings and as directed. (DRG NO. FD-1003/84(M)).

MS lock of suitable size with duplicate key.

S& F PVC handle of approved quality suitable for drawer.

Top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF 11) one side with approved shade and balancing white on other side duly teak wood beading 4x18/19mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of french polish

Hard rubber toe of suitable size.

M&L for repair chair CB steel by replacing the following parts with first class teak wood duly polished with high gloss finish of french polish complete all as per the drawings and as directed. (DRG NO. FD-75(M)) Seat/back(duly canned with approved quality of cane and as per godrej pattern)

MS cleats of size 20mm x 3mmx40mm long duly welded to frame to support seat.

Handle made out of first class teak wood.

S& F Hard rubber shoe of approved quality and suitable size.

M&L for repair Table bed side MAP by replacing the following parts with prelaminated MDF board(exterior gde)/plywood MR gde complete all as per drawings and as directed . (DRG NO. FD/E6/MAP/15, FD/E6/MAP/15(R))

Top made out of 18/19 mm thick pre-laminated exterior gde MDF board OSL(Designation PLMDF-11) one side with approved shade and balancing white on other side duly provided with teakwood beading of suitable size.

Side made out of 18/19 mm thick pre-laminated exterior gde MDF board OSL(Designation PLMDF-11) one side with approved shade and balancing white on other side complete.

Back made out of plywood 6mm thick MR Gde.

Bottom made out of plywood 6mm thick MR Gde.

Upper drawer complete.

Lower drawer complete.

CP handle of approved qulity and suitable size.

Telescopic channel of suitable size and approved quality.

M&L for repair bed hard MAP by replacing the following unserviceable parts with approved ones complete all as per drawing and as directed. (DRG NO. FD/E6/MAP/08,FD/E6/MAP/08®)

Plywood top 12mm(9 ply) thick MR Gde.

Nut and bolt with washer complete.

Pre-laminated MDFboard(exterior gde) of Head rest complete.

Pre-laminated MDFboard(exterior gde) of foot rest complete.

PVC cap of suitable size.

M&L for repairs Chair executive revolving high back by replacing unserviceable parts as per drawings/ TP complete all as specified and directed. Note:- sample and shade of materials will be determined as per actual requirement at site.cost of tapestry cloth shall not be less than 150/-per meter and Cost of rexine cloth shall not be less than 350/- per meter .

Only tapestry cloth of seat and back complete.

Only rexine cloth of seat and back complete.

foam of seat/ back complete.

Only Plywood of seat /back.

Hydraulic of suitable size.

Base CP as reqd of suitable size and pattern

Base PVC of suitable size and pattern.

Wheel of suitable size and pattern.

Arms as requred by size and design(spl).

M&L for repairs to Chair revolving med/ low back by replacing unserviceable parts as per drawings/TP complete all as specified and directed. Note:- sample and shade of materials will be determined as per actual requirement at site.cost of tapestry cloth shall not be less than 150/-per meter and Cost of rexine cloth shall not be less than 350/- per meter .

Only tapestry cloth of seat and back complete.

Only rexine cloth of seat and back complete.

foam of seat/ back complete.

Only Plywood of seat /back.

Hydraulic of suitable size.

Base PVC of suitable size pattern.

Wheel of suitable size and pattern.

Arms as requred by size and design.

M&L for repair to Chair computer revolving by replacing unserviceable parts as per drawings/TP complete all as specified and directed. Note:- sample and shade of materials will be determined as per actual requirement at site.cost of tapestry cloth shall not be less than 150/-per meter.

Only tapestry cloth of seat and back complete.

foam of seat/ back complete.

Only Plywood of seat /back.

Arms as requred by size and design.

M&L for repair Chair writing Map by replacing unserviceable parts as per drawing complete all as specified and directed. (DRG NO. FD/E6/MAP/12). Note:- sample and shade of materials will be determined as per actual requirement at site.Cost of tapestry cloth shall not be less than 150/-per meter.

Only tapestry cloth of seat and back complete.

foam of seat/ back complete.

Only Plywood of seat /back.

Arms as requred by size and design.

M&L for repair to Chair visitor by replacing unserviceable parts as per drawings/TP complete all as specified and directed. Note:- sample and shade of materials will be determined as per actual requirement at site.Cost of rexine cloth shall not be less than 350/-per meter and .Cost of tapestry cloth shall not be less than 150/-per meter. .

Only tapestry cloth of seat and back complete.

Only rexine cloth of seat and back complete.

foam of seat/ back complete.

Only Plywood of seat /back

Removing unsv plywood from Charpoy plytop and S&F 12mm thick(9 ply) plywood BWR Gde with suitable size of nut and bolt including welding of loose joints,if any and painting by brush with one coat of 1st quality synthetic enamel paint of approved shade complete all as specified and directed. (DRG NO. FD/MAP/-II/01)

Removing unserviceable plywood from Charpoy folding and S&F 8/9mm thick plywood MR Gde with suitable size of nut and bolt including welding of loose joints,if any and painting by brush with one coat of 1st quality synthetic enamel paint of approved shade complete all as specified and directed. (DRG NO. FD-388(R) )

Removing unserviceable plywood from Charpoy GI Pipe and S&F 12 mm thick (9 ply) plywood of BWR Gde duly teakwood beading 12mm thick half round dia all around of suitable size fixed by pannel pins and adhesive with diamond cut pattern finishing at corner and fixing with suitable size of nut,bolt and washer to frame after titening of complete frame including welding of loose joints,if any and painting of flat/angle iron by brush with one coat of 1st quality synthetic enamel paint of approved shade complete all as specified and directed. (DRG NO. FD-220 ) Note:- shape,pattern and size of nut, bolt and washer shall be approved by GE.

M&L for repair charpoy GI pipe nylone newar by replacing the following unserviceable parts with approved ones complete all as specified and directed. (DRG NO. FD-220)

Plastic newar 50/55 mm width ( white colour),made out of virgin plastic of approved quality woven in V shape and sample as available in BSO office. Note:- (i) The weight of nylone newar shall be 1.5 kg per charpoy. (ii) The entire frame includuing legs of charpoy shall be titened before weaving.

Long rail made out of 32mm bore GI pipe medium grade of suitable size duly threaded up to 22mm on both side.

Fixing of short rail of suitable size made out from long rail as obtained from Serial Item No. 26.02 above duly threaded up to 22mm at both end.

Fixing of leg of suitable size made out from short rail as obtained from sr no 26.03 above duly threaded up to 22mm.

GI elbow3 way medium gde ISI marked suitable for 32mm bore GI pipe.

GI check nut medium gde of suitable for 32mm bore GI pipe.

M&L for repair bed by replacing the following unserviceable parts with first class teakwood complete all as per drawings and as directed. (DRG NO. FD-246/247)

Long rail.

Stiffener

Head rest

Foot rest

S& F 'L' shape MS flat iron 30mm x 5mm x125 mm long (painted with 1st grade black colour synthetic enamel paint over a coat of red oxide primer) between leg and rail to tight the whole frame complete.

3.5/4mm thick teak face plywood, including half round teakwood beading if broken, of both side of head rest complete.

3.5/4mm thick teak face plywood, including half round teakwood beading if broken, of both side of foot rest complete.

Plywood 12mm thick(9 ply) BWR Gde of suitable size.

M&L for repair Chair dining cushioned MAP by replacing the following unserviceable parts with first class teakwood. complete all as as per drawings and as directed. (Drg No FD/MAP-II/04,FD/E6/MAP/10(R)) Note:- sample and shade of materials will be determined as per actual requirement at site.cost of rexine cloth shall not be less than 350/-per meter tapestry cloth shall not be less than 250/- per meter.

Front leg

Rear leg

stiffener

only tapestry cloth of seat complete

vertical strip

Rexine cloth of seat complete

Foam 75mm (40 D) of seat complete.

Plywood 12mm thick (9 ply) MR gde

PVC shoe 15mm dia of approved quality

M&L for repair Chair dining by replacing the following unserviceable parts with first class teakwood complete all as per drawing and directed. (DRG NO. FD-279/270/228/203 FD/MAP-II/05 )

Front leg.

Rear leg.

Stiffener.

PVC shoe 15mm dia of approved quality.

PVC seat4x10mmthickRIBS moulded alongwith seat in single piece of approved quality

Back rest.

M&L for repair Chair writing by replacing the following unserviceable parts with first class teak wood complete all as per drawing & as directed. (DRG NO. FD-280/250)

Front leg.

Rear leg.

Stiffener.

Back rest.

PVC shoe 15mm dia of approved quality.

M&L to repair Chair easy by replacing the following unserviceable parts with first class teakwood.Rest all as per drawing and as directed by engr-in-charge. (DRG NO. FD-229/201)

PVC shoe 15mm dia of approved quality.

M&L for repair Peg table by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-384/277/236)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 15mm dia of approved quality.

M&L for removing existing old/unserviceable canes from different types of chairs and recaning the same with 2mm half round dia made out of virgin plastic in godrej pattern as shown on relevent drawings complete all as specified and directed.

M&L for repair Teapoy by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-382/278/232/34)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 20mm dia of approved quality.

M&L for repair Table centre by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-134/235/ 274/375)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 20mm dia of approved quality.

M&L for repair Table 900mm x600mm without drawer/ With drawer by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-283/224/284/231/223/

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size

Leg made out of first class teakwood.

Front/rear rail made out of first class teakwood.

side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

Drawer complete.

PVC shoe 20mm dia of approved quality.

M&L for repair Table 900mm x900mm by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-291)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size

Leg made out of first class teakwood.

side rail made out of first class teakwood.

Rail made out of first class teakwood.

PVC shoe 25mm dia of approved quality.

M&L for repair Table dinning (1200mm x900mm) by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD/MAP-II/03)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size.

Leg made out of first class teakwood.

Front/rear rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 25mm dia of approved quality.

M&L for repair Table dinning 6 person by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed (DRG NO. FD-273/239/30(M)/FD/MAP-II/03)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 25mm dia of approved quality.

M&L for repair Table dinning 8 person by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde) complete all as per drawing & as directed. (DRG NO. FD-273/239/30(M))

Top made out of 18/19mm thick pre-laminated exterior gde MDF board duly teakwood beading 4x18/19mm thick all around of suitable size

Leg made out of first class teakwood.

front rail made out of first class teakwood.

side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

PVC shoe 25mm dia of approved quality.

M&L for repair Table bed side by replacing the following parts with first class teakwood/ prelaminated particle board (exterior gde) complete all as per drawing & as directed (DRG NO. FD-276/248/210)

Top made out of 18/19 mm thick pre-laminated exterior gde MDF board OSL(Designation PLMDF-11) with approved shade duly provided teakwood beading infront of suitable size.

Side complete

Bottom complete

Shelf 12mm thick complete

Back ply 6mm thick MR Gde complete

M&L for repair Table dressing gents with mirror by replacing the following unserviceable parts complete as per drawing & as directed. (DRG NO. FD-230/31(M))

Top made out of 18/19mm thick pre-laminated MDF board exterior gde OSL (Designation PLMDF-11) duly provided teakwood beading infront of suitable size.

Bottom complete

Side complete.

Back ply of base made out of plywood 12mm thick( 9 ply) MR gde complete.

Only Mirror 5mm thick of suitable size.

Mirror with Frame made out of first class teakwood and 6mm thick MR Gde plywood complete.

Drawer complete.

M&L for repair Table dressing ladies with mirror by replacing the following unserviceable parts complete all as per drawing & as directed. (DRG NO. FD-251/32(M))

Top made of 18/19mm thick MDF board

Bottom complete

Side complete

Back ply of base made out of plywood 12mm thick (9ply) MR gde complete

Only Mirror 5mm thick of suitable size

Plain glass 5 mm thick for sliding

Aluminium channel complete of suitable size for sliding of glass

Drawer complete

Leg with frame made out of first class teakwood

M&L for repair Side board by replacing the following unseviceble parts complete all as per drawing and as directed. (DRG NO. FD-241,371)

Top made out of 18/19mm thick pre-laminated MDF board exterior gde OSL (Designation PLMDF-11) with approved shade duly provided first class teakwood beading infront of suitable size.

Bottom complete.

Side complete.

Partition complete.

Single shutter duly provided teakwood beading on edges complete.

Shelf 12mm thick complete.

Back ply 6mm thick MR gde.

Legs with frame made out from first class teak wood complete.

Drawer complete.

M&L for repair Bin soiled linen multipurpose by replacing the following unserviceable parts complete all as per drawing and as directed. (DRG NO. FD/E6/MAP/09)

Top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-11) one side with approved shade and balancing white on other side duly provided PVC beading all around of approved quality

Bottom complete

Side complete.

Partition complete.

Single shutter duly provided teakwood beading on edges complete.

Back ply 12mm thick (9 ply) MR gde.

Legs with frame made out of first class teakwood complete.

Drawer complete.

CP handle of approved qulity and suitable size.

M&L for repair Table writing by replacing the following unserviceable parts complete all as per drawing & as directed. (DRG NO. FD-275/249/33(M))

Top made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-11) of approved shade duly providing teakwood beading all around complete

Leg made out of first class teakwood complete

Front rail complete

Side rail complete

Side stiffener complete

Center stiffener complete

Teakwood frame( comprising one stiffener and two legs) of suitable size and shape

Drawer complete

Lock of suitable size with duplicate key complete

M&L for repair Book case wooden by replacing the following unserviceable parts complete all as per drawing & as directed. (DRG NO. FD- 237)

Top made out of 18/19 mm thick pre-laminated particle boardof approved shade duly provided with teakwood beading of suitable size.

Bottom complete

Side complete

Shelf complete

shutter complete

Leg with frame made out of first class teakwood complete

Back ply 6mm thick MR Gde complete

Lock of suitable size with duplicate key complete.

M&L for repair Sofa set 5/4 seater by replacing the following unserviceable parts with first class teakwood complete all as per drawing and as directed. (DRG NO. FD-281/373)

side rail.

Batton seat/back.

Front rail of single seater.

Front rail of three seater.

Back rest rail top/side of single.

Back rest rail side of three seater.

Back rest rail top of three seater.

Removing old foam cushion with tapestry cloth and S&F new P.U.Foam cushion of size 530mmx560mmx100mm (40 density) duly covered with approved quality of tapestry cloth and zip shall be provided three sides of the cushion cover complete all as specified and directed. Note:- Cost of tapestry cloth shall not be less than 250/- per meter.

Removing worn out tapestry cloth from old cushion and replacing the same with new tapestry cloth of approved quality and zip shall be provided three sides of the cushion cover complete all as specified and directed. Note:- Cost of tapestry cloth shall not be less than 250/- per meter.

M&L For repair Sofa set 5 seater by replacing the following unserviceable parts with first class teakwood complete all as per drawing and as directed. (DRG NO. FD-258)

Front/Side/Back rail of single seater

Back Rest batton single seater

Back Rest batton three seater

Front /Back rail of three seater

Plywood of seat single seater 8/9mm thick MR Gde

Plywood of seat three seater 8/9mm thick MR Gde

Removing of old foam cushion with tapestry cloth from back and S&F new P.U. Foam cushion 45mm thick ( 40 density) duly covered with approved quality of tapestry cloth including all necessary repair and replacement of required materials like jute cloth, wooden batton etc. complete all as specified and directed. Note:- cost of tapestry cloth shall not be less than 250/- per meter.

Removing worn out tapestry cloth from old cushion of seat/Back and replacing the same with new tapestry cloth of approved quality and zip shall be provided three sides of the cushion cover complete all as specified and directed. Note:- cost of tapestry cloth shall not be less than 225/- per meter.

M&L for repair fully uphostry sofa set 5 seater cladded with tapestry cloth by replacing tapesty cloth of approved quality including replacement of unserviceable material like cotton,coir,foam,GI spring, wooden members etc. and polishing the exposed surface of the same with high gloss finish of french polish complete all as per drawing/ TP and as directed. Note:-(i) Sample and shade of material will be determined as per actual requirement at site. (ii) Cost of tapestry cloth shall not be less than 350/- per meter.

Top made out of 18/19 mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-11) one side with approved shade and balancing white on other side duly provided with PVC beading of as requaired complete.

Side made out of 18/19 mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-11) one side with approved shade and balancing white on other side.

Board drawer complete

Mouse drawer complete

Middle shelf complete

Bottom shelf complete

Telescopic channel of suitable size and approved quality Note:- Sample and shade of materials will be determined as per actual requirement at site.

M&L for dry cleaning of chair computer,chair revolving med/high back and chair visitor, chair writing MAP by soda,sampoo,castic,urea, chemical etc to clear the dust complete all as specified and directed.

M&L for dry cleaning of full upholstery sofa set 5 seater by soda,sampoo,castic,urea, chemical etc to clear the dust complete all as specified and directed.

M&L for repair hat stand with mirror by replacing the following parts with approved ones complete all as per drawing and as directed. (DRG NO. FD-233)

First class TW beading at all around of frame

Mirror 5mm thick.

Aluminium pegs, 100mm long.

Aluminium nail hook, 50mm long.

M&L for Spot welding on various items of steel furniture FD/TP complete all as specified and directed.

M&L for Repair to various type of wooden chairs and tightening the whole frame of chair FD/TP complete all as specified and directed.

M&L for preparation of old steel surface of chair verandah and welding loose joints, if any including de-rusting the surface and painting with two coat of synthetic enamelled paint white colour (1st Grade Quality) and recaning with 4-5 mm half round 0.8 thick plastic cane made out of virgin plastic, in existing pattern complete all as specified and directed. ( Drg No. FD-359/259/256/19 )

S&F hard rubber shoe of approved quality suitable for chair verandah complete all as specified and directed.

SMS Enterprises

M/S NEHAL ENTERPRISES