PROVN OF SINGLE ORs (OTM ACCN) WITH TWO HAVILDAR ROOMS WITH TOILETS AND BATHROOMS AND SPECIAL REPAIR TO JCO/OR MD QTR INSIDE NCC OTA AT MORAR CANTT, GWALIOR

Amount

Excavating over areas, n exc 1.5 m deep and getting out in Soft Loose soil complete all as specified and directed.

Surface dressing n.exc (not exceeding) 30cm deep average 15cm deep in Soft Loose soil complete all as specified and directed.

Add or deduct in above item for every 3cm or part thereof above below 15cm average depth complete all as specified and directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers n.exc 15 cm thick, spread , levelled and rammed including watering complete all as specified and directed.

Removing excavated material n.exc 500m and depositing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n. exc 3.00 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams , plinth beams , base for coloumns and mass concrete etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate) as in coloumns , pillars , piers , posts and struts etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers , lintel over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in slab supported on walls ,beams, coumnns in floor, roof, landing complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in Chajjas complete all as specified and directed.

M&L for use and waste formwork to sides of concrete foundation , footing, base of coulmn , raft, raft beam sides and soffits of foundation and plinth beam for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork to soffits of suspended slabs such as roof slabs , floor slabs, landings and similar works , not exceeding 200 mm thick ( horizontal or sloping ) including slab edges for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork to fins, louvers, fascia for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork for to sides of pillar ,post ,struts ,pier column rough finished surfaces of concrete rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste Formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed.

M&L for Use and waste Formwork to chajjas including edges for rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars ,6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia , as in stirrups , spacers , and binders , cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L forTreating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for Treating the soilbackfill in contact with foundation at the rate of 7.5 litre of emulsion per square meter of vertical surface ( area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for Moorum red bajri filling in floor or paving laid in layers n. exc. 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as specified and directed.

M&L for non skid ceramic, joint free Coloured tiles, 300mmx300mmx 6 mm to 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar( 1:6) complete all as specified and directed.

M&L for digital glazed ceramic tiles,joint free coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

M&L for machine cut Kota stone slab 18 mm to 22 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing , over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:3) complete all as specified and directed.

M&L for machine cut kota stone slab 10 mm -15 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L Granite slab 18 mm to 20 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed CM (1:3) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing all as specified and directed..

M&L marble stone strip as in border etc in kota stone flooring machine cut bedded over and including 20 mm thick screed bed CM (1:3) jointed and ointed with grey cement slurry including cutting and polishing to mirror finish complete all as specified and directed.

M&L for rubble random rubble uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L for 3D printed concrete wall panel comprising of 3 layer of overall thickness wall 230mm complete all as specified and directed.

M&L for 3D printed concrete wall panel comprising of 3 layer of overall thickness wall 150mm complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement including complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M & L for two coat of oil bound emulsion paint over a coat of Birla wall care putty on plastered surfaces on wall incl. preparation of surfaces complete all as specified and directed. .

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coat of cement base paint over a coat of primer complete all as specified and directed.

S&F galvanised wire cloth, 0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

S&F pressed steel frame 125mmx60mm for doors with one or more rebates including necessary fixing lungs and hinges, lock strike plate,etc complete all as specified and directed.

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

S&F aluminium alloy, anodized sliding door bolt of 250mm length with hasp and staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for aluminium anodised barrel tower bolt of 150mm of extruded section complete all as specified and directed.

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and directed.

S &F for factory made solid panel PVC door shutter 30mm thick ( style) consisting to frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete without glazing bars, dovetailed or welded complete all as specified and directed.

M & L for 30mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

S & F factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays , complete with glazing bars, Complete all as specified and directed

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290,E-165 , complete all as specified and directed.

S & F 150 mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S&F for floor door stopper of brass body and tongue, overall length of cover plate 150 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F 3mm thick pin headed figured sheet glass quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F 25mm dia stainless steel curtain rod not less than 0.80mm thick including fixing of sufficient brackets ( minium 2 nos at every 1.50m length) and knobs complete all as specified and directed.

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.

S&F for of vitreous china wash basin, white, oval type, (size as approved by Engineer In charge) Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid separetly.

S&F for viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed.

S&F plastic water closet seat covered white coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devise complete all as specified and directed.

M&L for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed and making good to floor, complete all as specified and directed.

S&F for vitreous china, Half stall type ,white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F for PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

M&L painting to steel surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of red oxide including prepration of newly or previously untreated surface complete all as specified and directed.

M&L painting to wooden surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of pink primer including prepration of newly or previously untreated surface complete all as specified and directed.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and directed. Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) land on primed surface by torch application complete all as specified and directed.

M&L one coat of aluminium bituminous paint over polymetric membrane complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in ant type of soil complete all as specified and directed. Note : Soil under filling will be approved by GE. Black cotton soil not be used in returning filling rate of filling of approved soil include in this item and no additional payment shall be given for filling of soil.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triplr layer in construction white in colour hoisted and fixed in position complete all as specified and directed.

S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F 15mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling including concealed/open (Rate of chasing and cutting etc is included) etc complete all as specified and directed.

S&F 20 mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc complete all as specified and directed.

S&F 25mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc complete all as specified and directed.

S&F for gun metal globe valve with iron wheel head screwed both ends for iron pipe of 20mm bore, complete all as specified and directed.

S&F for in repair gun metal globe valve with iron wheel head screwed both ends for iron pipe of 25mm bore, complete all as specified and directed.

S&F for 15mm ,bib tap ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket and guard and railing 60cm long completed all as specified and directed.

S&F for Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F 15mm angle cock ISI Mark chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified and directed.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed

S&F PVC (SWR) pipes, 75 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) pipes, 110 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) Single junction (single T) equal or unequal, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) Single junction (single T) equal or unequal, , 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends with access door, 110 mm bore, any radius with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

M&L cast iron nahani trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F for peg set of six M.S. Cast Iron . fixed to wall with PVC plugs and screw, complete all as specified and directed.

S&F for 18 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised complete all as specified and directed.

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified and directed.

S&F for in repairs Heatth Faucet (ABS Body) mild steel chromium plated 15 mm dia with 1.25 meter PVC flexible body pipe of CP including fixing bracket, complete all as specified and directed.

M&L for PCC 1:3:6 type C0 (12.5mm agrregate) for filling in pressed steel frames and like complete all as specified and directed.

Preparattion of surfaces for writing Building numbers and applying two coat of synthetic enamel paint back ground 30 cm dia and writing letters (Block, Roman, italic or indian) of n exc 10 cm height, width of letter shall not be less than 15mm, with approved tint of synthetic enamel thick paint etc complete all as specified and directed.

Preparattion of surfaces for stops, commas, lines, brackets and making outer boarder with approved tint of synthetic enamel thick paint and applying two coat of synthetic enamel paint etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick / concrete/ stone surfaces mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid seperatly under appropiate item of schedule 'A'

M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in bed to drain pipe including packing under and hunching against the sides of pipes after they are laid and tested complete for pipe size of 150mm bore complete all as specified and directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in surfaces channels drains and benching including form work and finishing fair and smooth using extra cement (forming fair finished channel shall be measured and paid for separately) complete all as specified and directed.

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone agg) as in cover slabs for man holes and set in CM 1:4 including necessary from work complete all as specified and directed. Note: Reinforcement and form work shall be measured paid separately)

Cutting holes in brick/stone wall ,depth of embedment portion of hold fast exc half brick wall but not exc one brick wall, built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance exceeding 500 metre but n exc and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

M&L for reinforced cement concrete NOMINAL MIX Type B-O (1:2:4) ( using 20 mm graded stone aggregate ) as in slab supported on walls ,beams, coumnns in floor , roof , landing complete all as specified and directed.

M&L use and waste formwork to soffits of suspended slabs such as roof slabs , floor slabs, landings and similar works , not exceeding 200 mm thick ( horizontal or sloping ) including slab edges for rough finished surfaces of concrete complete all as specified and directed

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area of following 25 Sqmm 4 Core complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area of following 10 Sqmm 2 Core complete all as specified and directed.

Supply and fix steel tubular swaged poles type 410 SP-31 (9 meter long) complete with CI base plate and finial taper plug, bolts, nuts & screws complete all as specified and directed.

Supply and fixing of 72 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure dia cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING separate driver compartment with IP 66 protection and impact resistance of IK 07 with 10 KV Built-in-SPD complete all as specified and directed.

M&L for GI Brackets bending & shaping of size 32 mm dia galvanised iron pipe light grade over all length 0.60 mtr including necessary clamps, brackets and bolts etc to fixing on pole complete all as specified and directed.

S & F 1100 V Grade PVC insulated,aluminium conductor & overall PVC sheathed in service connection with 3 core cables of size 6 Sqmm & connecting to light fittings/tertminal boxes complete all as specified and directed.

Material & Labour for cement concrete 1: 2: 4 type B2, using 40mm graded crushed trap stone aggregate in foundation of pole, filling and mass concrete complete all as specified and directed.

Material & Labour for cement concrete 1: 3: 6 type C1, using 20mm graded crushed trap stone aggregate for coping complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point in soft/loose soil complete all as specified and directed.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and directed.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and directed.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

M&L for earthing complete with galvanised steel pipe electrde, 40 mm bore medium grade 2.5 mtr length burried directly and preferably vertically in ground with top edge not less than 1.25 mtr below normal ground level connected with earthing lead 4 mm dia galvanised iron or steel wire all as shown in electrical Plate No. 02 of MES SSR to the earthing test point all as specified and indicated including testing on completion complete all as specified and directed.

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 63 Amp,4 pole & Including MCCB 63 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set over and including 15 mm thick cement screed in (1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L ditto item above for ceramic tiles, joint free, coloured tiles 7mm to 8 mm mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:3 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.with the colour of tiles complete all as specified and directed.

Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M& L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

M & L PCC (1:2:4) Type B1 using 20 mm graded stone aggregate as levelling course/mass concrete complete all as specified and directed.

M&L for PCC type B-1 (1:2:4) using 20mm graded stone aggregate as in coping/ mass concrete complete all as specified and directed.

S&F for machine pressed precast Coloured concrete Tile with grey cement and no pigments size 300x300mm of 25mm thick over 20mm thick CM (1:6) screed bed complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed.

Material and labour for Preparation of old decorated surface of walls of plastered or unplastered surfaces by brooming down or steel wire brushing, scarping down smoke soot, moulds, moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed.

Material and labour for Preparing of old decorated surface of Ceilings of plastered or unplastered surfaces by brooming down or steel wire brushing, scarping down smoke soot, moulds, moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L complete removal of existiong treatment (internal and external) on walls by scrapping with steel wire brushing, scraping down smoke soot/ plants roof from wall/chhajjas and applying two coat of cement based paint on walls including preparation of old plastered or un plastered surface comlete all as speified and directed.

M&L Complete removal of existing treatment (internal and external suraces) on walls by scrapping with steel wire brush or any other means including two coat of wall care putty on wall and applying two coat of oil emulsion complete all as specified and directed.

Complete removal of exiting treatment from external wall preparation of old plastered surface and applying two coat of premium acrylic exterior anti algal fungal emulsion paint over one coat of weather coat exterier primer on wall complete all as specified and directed.

Material and labour for prepration old or untreated surfaces of wood or wood based surfaces and applyingone coat of synthetic enamel paint over a prime coat of pink primer on surfaces of any desription, not otherwise described, over 10 cm width or girth complete all as specified and directed.

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

All as per above but above but wire guage panel i.e. panel should be wire guage in lieu of PVC sheet panel. Wire guage shall be wraped on a additional square tube 8mm M.S. solid tube and tube shall be welded to M.S. tube. and wire guage shall be strechted tightly firmed complete all as specified and directed.

S&F 30mm thick Flush shutters ,soild core construction ,with paticle board core and plywood face panels , commercial type complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed. Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S&F galvanised wire cloth, .48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

S&F for aluminium butt hinges of 100mm size complete all as specified and directed.

S&F for Mild Steel Butt hinges , medium weight, cold rolled , of size 100 mm complete all as specified and directed.

S&F for MS 150 mm ordinary rat tail springs plate type incl.rollar plate etc, complete all as specified and directed.

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete complete all as specified and directed.

S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps nexc 30 mm (when open), complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised complete complete all as specified and directed.

S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed.

S&F for PVC bath room cabinate mirror of Size 500mmx400 mm make Prayag Cat No 556 or equivalent complete complete all as specified and directed.

S&F for in repair Curtain rod stainless steel decorative type 25 mm dia including fixing bracket and end knobs complete all as specified, complete all as specified and directed.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 15mm bore of pipe, complete all as specified and directed.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removing to store of 25mm bore of pipe, complete all as specified and directed.

supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete complete all as specified and directed.

supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete complete all as specified and directed.

Desmantaling of PVC / AC rain water / vent / waste pipes, any size including all fittings complete all as specified and directed.

S&F for 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door, complete all as specified and directed.

M&L for 75 mm dia of out let PVC (SWR) floor trap plain with CP grating including jointing with solvent cement as in repair complete all as specified and directed.

S&F for 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair, complete all as specified and directed.

Dismantling water tanks of any description and in any position , of capacity exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed.

S&F for rotational moulded poly-ethylene Three layered insulation puff tanks (cylinderical vertical ) 1000 litres capacity, white colour hoisted and fixed in position complete all as specified and directed.

S&F for in repair gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 20mm bore, complete all as specified and directed.

S&F for in repair gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 25mm bore, complete all as specified and directed.

S&F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long, complete all as specified and directed.

S&F for in repairs Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F for in repair aluminium anodised tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed.

S&F for aluminium peg set of six fixed to wall with PVC plugs and screw, complete all as specified and directed.

S&F for in repairs of vitreous china wash basin, white, flat back/ oval, size 500 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid separetly.

S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm, complete all as specified and directed.

S&F for as in repair viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed. .

S&F for in repairs sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plug washer and waste coupling, waste pipe including bedding in CM to dwarf wall or including fixing cantilever brackets and connections to pipe over all size 915mmx460mm built size 410mmx330x160mm, complete all as specified and directed.

S & F in repair for plate rack made out of .90 mm thick stainless steel of wire type / sheet pattern size nad type as directed by Engineer In Charge and approved by GE fixed to wall with necessary fitting arrangement Complete all as specified and directed.

S&F for in repairs PVC Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm125gms complete all as specified and directed.

S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed complete all as specified and directed.

S&F for in repairs for 15 mm Stop valve cast copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm bore or for unions complete all as specified and directed.

S&F for in repairs Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F for in repairs Heatth Faucet with one meter PVC flexible body pipe of CP including fixing bracket, complete all as specified and directed.

S&F in repairs for wall mixer with Two in one pattern in of brass CP, complete all as specified and directed.

S&F for in repairs mild steel Chromium plated grating 100 mm dia, fixed in repairs to Nahani traps, complete all as specified and directed.

Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed.

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm double ribbed plain steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding (ridge) to wall fixed with self tapping screws complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed.

Dismantling of timber in fillets, rails, posts, rafters, purlins etc under 40 Sq. cm provided for complete all as specified and directed.

M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed

M&L two coat of synthetic enamel paint over coat of Red oxide primer over Old steel surfaces nexc 10 cm width or girth complete all as specified and directed.

Taking down existing tarfelt and plaster from roof and removing from site complete all as specified and directed.

Demolition of cement concrete of any description and in any position (reinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed. Note:Demolition material throughout MOD Land rate include above item .

Demolition of cement concrete of any description and in any position reinforced concrete (re-inforcement cut to facilitate demolition) including disposal of unserviceable of mateial complete all as specified and directed. Note:Demolition material throughout MOD Land rate include above item.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and directed. Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "Supply only ".

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L, precast cement concrete tiles of size 250mm x 250mm x 20 to 22 mm as in foor top ,confirming to IS-1237 laid over 15 mm thick screed bed in CM 1:4 and set, jointed and pointed in neat cement slurry in floors, and cut & plished between tiles 2 to 3 mm will be filled with cement mortar (1:2) by mixing of chemical or equilant approved by the GE etc complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate pan, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided for in water troughs and the like including weathering, slightly rounded or chamfered angle complete all as specified and directed.

M&L Plain cement concrete (1:5:10) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L for providing two coats of water proof coating of pidifine 2K of Dr. fixid or euivelent in other make complete all as specified and directed.

M&L 10mm thick rendring with CM (1:3) over wall/floor surface even and smooth mixed with WPC complete all as specified and directed.

S&F in repair galvanised wire cloth, .48mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

M&L for 75mm thick PCC (1:2:4) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

S&F for in repairs for 15 mm bib tap fancy type long body chromium plated, cast copper alloy with capston heads, scewed down high pressure with or without lettered 'Hot' or 'Cold' with long srewed for iron pipe complete all as specified and directed.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixed in repairs complete all as specified and directed.

M&L for PCC type B-2 (1:3:6) using 40mm graded stone aggregate as in foundation filling mass concrete complete all as specified and directed.

Excavating over areas, exc 1.5 m but n exc 3.00m deep and getting out in Soft Loose soil complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:-

One light point controlled by one switch.

One Ceiling Fan point controlled by one switch.

One Ceiling Fan Exhaust fan point controlled by one switch.

One 3 pin socket outlet 5 Amps controlled with one switch on the same board.

One 3 pin socket outlet 5 Amp controlled by one switch on independent board.

One bell point controlled by one bell push

For one light point controlled by 2- two way switch

Description all as per Ser item No 230 above but point wiring with 4.0 Sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 4.0 Sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed.

Description all as per item No. 230 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F Switch socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete all as specified and directed.

S&F switch piano, flush button single pole one way 15 Amp complete all as specified and directed.

S&F S/ socket out let multipurpose, flush type, 2 in 1 6 Pin 5/15 amps complete all as specified and directed.

S&F Ceiling rose 3 terminal/pvc/polycarbonate, isolated body complete all as specified and directed.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 watt, 240 volts, AC 50 Hz complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete all as specified and directed.

S&F LED Lamp 09/10 watt complete all as specified and directed.

S&F LED lights fitting 1x20W, 220V, AC decorative box type with driver, holder including LEG tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply & fix BEE Service value > 6.0 ceiling fans 1200 mm sweep with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed.

S&F Exhaust fan steel body AC single phase, 230V of size 300 mm sweep with blades, and frame and louvers, voltage 230V, 50Hz, RPM 1200, Copper winding complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

All as per Ser item No.245.00 but submain with 4 sqmm FRLSH confirming to IS 694:2010, multistrand copper (ISI marked with valid CML No), cable 1100 Volt grade, 4.0 Sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and earth plug, single pole and neutral with single pole MCB 20 Amps 240 Volts in repairs complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F MCB SPN 40 Amps, 240 Volts 'C' series 16 KA, including connection with suitable size copper lugs complete all as specified and directed.

S&F MCB SP 240 Volts, 6 to 32 Amps, 'C' series 10 KA, including connection with suitable size copper lugs complete all as specified and directed.

S&F tube Medium' grade galvanised with all fitting laid in trenches, of 50 mm dia complete all as specified and directed.

S&F tube Medium' grade galvanised with all fitting fixed to wall/floor, of 20 mm dia complete all as specified and directed.

S&F gun metal gate valves with iron wheel head screwed at both ends for iron pipes of 50 mm dia complete all as specified and directed.

S&F gun metal gate valves with iron wheel head screwed at both ends for iron pipes of 20 mm dia complete all as specified and directed.

M&L for Construction of valve chambers with 150 mm thick PCC foundation 1:4:8 type D2 using 40 mm graded trap stone aggregate, 230 mm thick brick masonary wall with sub class 'B' bricks builts in cement mortar 1:4 10 mm thick plastering to brick masonary in cement mortar internally and externally upto 15 cm below ground level, 50 mm thick coping with PCC 1:2:4 type B1 using 20 mm graded crushed trap stone aggregate valve chamber frame cover made of mild steel angles of size 40mm x 40mm x 6mm and cover made of 2.5 mm thick mild steel sheet fixed with mild steel hinges - 02 Nos, locking arrangements with provision of locks and painting the steel surfaces with two coats of synthetic enameled paint over a coat of zinc chromate primer including neccessary earth work, excavation, all as specified and directed of size 1.0 x1.0 x1.0 internal dimentions.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point in soft/loose soil complete all as specified and directed.

Cutting of existing Cast iron pipes in position for insertion of new tees, for branch connection of 40 mm dia from bore of pipe existing CI pipe complete all as specified and directed.

Supply & fixing water heater storage type metallic outer body and stainless steel inner container, 25 Ltrs capacity, electric suitable for single phase, 50 Hz, AC Supply, 5 star rating, including all necessary fittings and fixture with minimum 1M of three core 2.5 sqmm twisted copper conductor cable PVC sheated, three pin plug top complete with necessary fittings and fixtures all as specified and directed.

Supply and install, desert cooler, AC supply electric driven (single phase), 1400 rpm,having nominal air flow capacity of 5000 Cum/ hour complete with steel body construction is top cover, side supports angle & water storage Tank with 20 SWG & side panels with 22 SWG steel Sheet as per standerd design of manufacturers for air flow capacity 5000 Cum/Hrs complete all as specified and directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down ceiling fan of any sweep,removing blades, cleaning the fan completely of dust and dirt and Re-hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook rubber pad, nut bolts and washers etc, complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed.

S&F switch piano, flush button single pole two way 5 Amp complete all as specified and directed.

S&F bell push flush type, 5 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F sheet metal Enclosure with socket Plug top and earth plug, single pole and neutral with single pole MCB 20 Amps 240 volts in repairs complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated unsheathed FRLS cable 1100 volts grade, 4 Sqmm size with multi stranded copper conductor (ISI marked with valid CML No), drawn in and including surface mounted non metallic rigid PVC conduit (ISI marked with valid CML No) not less than 20mm dia with all accessories including PVC insulated un sheathed 2.5 Sqmm cable with multistranded copper conductor (ISI marked with valid CML No) as connected to earth with dolly complete all as specified and as directed (Cutting of wall and making good disturbed surface of wall shall be measured & paid sepertely.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

M&L sub main wiring with two single core PVC insulated unsheathed FRLS cable 1100 volts grade, 1.5 Sqmm size with multi stranded copper conductor (ISI marked with valid CML No), drawn in and including surface mounted non metallic rigid PVC conduit (ISI marked with valid CML No) not less than 20mm dia with all accessories including PVC insulated un sheathed 1 Sqmm cable with multistranded copper conductor (ISI marked with valid CML No) as connected to earth with dolly complete all as specified and as directed (Cutting of wall and making good disturbed surface of wall shall be measured & paid sepertely,.

Supply & fix Exhaust fans 250 mm sweep with all fixing accessories required including making hole & regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, and testing complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed.

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 63 Amp,4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 35 Sqmm 3.5 Core complete all as specified and directed.

Supplying and laying reinforced precast concrete cable cover, class LT, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and directed.

M/s Manish Contractor

Arkay Instrumentation

M/s Gulshan and Brothers