PROVISION OF URINAL TOILET AT PANDEY HALL ITR RANGE AND PROVISION OF INTERLOCKING TILES RCC COVERED DRAIN FROM GURUDWARA TO RAM MANDIR ALONG MALL ROAD UNDER GE MIS MHOW

Amount

Excavating over areas, n exc.1.50m deep and getting out soft/loose soil complete all as specified and directed.

M&L for moorum/red bajri filling in floor or paving laid in layers n.exc 15cm thick spread,levelled and rammed including watering complete all as specified and directed.

Removing excavated material exc. 50m but n exc. 500 m and depositing where directed complete all as specified and directed.

Excavation in trenches n.exc. 1.50m wide and n exc.1.50m depth: for foundation, etc or for shafts,wells cesspits, manholes, pier holes, etc n exc. 10Sqm on plan & n exc. 1.50m in depth & getting out in hard/dence soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Formwork rough finished surfaced to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) in foundation, footings and similar RCC works complete all as specified and directed.

Formwork rough finished surfaces of concrete to sides of concrete flat or curves sides of pillers,posts, struts,piers,columns and stanchions complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) in coloumns,pillers,piers,posts and struts complete all as specified and directed.

Form work to sides and soffits of floor or roof beams haunching, lintel, coloumn, cantilevers shelves includig supported over hangs etc with rough finished flat surfaces of concrete complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in Beams,Cantilevers.brussumenrs,lintels over than 1.50 Span complete all as specified and directed.

M&L for use and waste of formwork to sides and soffits of slab such as roof slab,floor slab,landing and similer work,etc not exceeding 200mm thick with rough fnished surface of concrete flat complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in slab supported on wall , landings, beams canopies, deck slabs and shelves etc.complete all as specified and directed.

M&L for 10mm dia and over mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for 6mm to 8mm dia and over mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No 15.00 above but 5 mm to 10 mm dia as in Stirrups,spaces & binders complete all as specified and as directed.

M&L for brick work with fly ash brick with using modular size brick, straight or cured on plan exc 6m mean radiuos built cement mortar 1:6 complete complete all as specified and as directed

M&L for broken stone or boulder hardcore gauge n exc. 63mm, deposited spread and levelled in layers n exc. 15mm thick, watered and rammed to true surface complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub-base, to floor and foothpath etc complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) , type B-0 (using 20mm graded stone aggregate) as in floor as per leveling coursecomplete all as specified and directed.

M&L for screed bed or bedding layer 20mm thick for laying floor tiles in cement mortat 1:6 finished even and rough complete all as specified and directed.

M&L for coloured Non-Skid ceramic tiles 7 to 8mm thick (Square/Rectanguler ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm.in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Glazed ceramic tiles glossy series digital wall tile 300X450mmX7mm thick coloured on vertical surfaces set and jointed in neat cement slurry and pointed in white cement to matchover and including 10mm thick rendering of cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 , finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on unfair faces of brick work or concrete surfaces in cement mortar 1:4 using using water proofing compound @ 200 ml by weight of cement per bag, finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 mix type C2 (using 40mm graded stone aggregate) as in plinth protection and paving finishing concrete surfaces even and smooth without using extra cement complete all as specified and directed.

S&F Powder coating anodised aluminium ventilator (Louvers type) with louvers glass and glass stay,setion weighing 0.55Kg/m including necessary joining cleats, glazing clips for fixing of wiremesh,rubber neoprene packing,anodised aluminium snap beading screws etc.(minimum thickness of powder coating 50micron) complete all as specified and directed.

S&F pressed steel frames size 105X60mm for doors with one or more rebates including necessary fixing lugs,hinges,lock strike plate.etc complete all as specified and directed.

S&F factory made second class hardwood 35mm thick shutters, plain framed panelled shutter factory made (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 complete all as specified and directed.

S&F Solid PVC Door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinfourced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 100mm size MS butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed.

S&F 30mm size aluminium alloy,anodised sliding door bolt with hesp staple (bolt tye) and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixedcomplete all as specified and directed.

S&F PVC Pipes 110mm dia bore single socketed,in any length with rubber ring joints, laid in floors complete all as specified and directed.

S&F PVC (SWR) bends any radious 110mm complete all as specified and directed.

S&F PVC (SWR) 110mm brach pieace single ( single Y) equal or unequal complete all as specified and directed.

S&F 75mm dia PVC (SWR) multi floor trap.plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 100X100mm size Salt-glazed stoneware gully trap,square or round mouthed type P complete all as specified and directed.

S&F PVC Pipes 75mm bore single socketed,in any length rubber ring joints,laid in floors complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends complete all as specified and directed.

S&F 15mm bore GI tubes medium grade with all fitting a fixed complete to walls and ceiling or in floor complete all as specified and directed.

All as per tem No 44.00 above but 25mm bore complete all as specified and directed.

S&F 25mm dia Gun metal valve globe or gate valves,with iron wheel head,screwed both ends foriron pipe and fixed complete all as specified and directed.

S&F rotational moulded polythylene water storage tanks (double layer), 1000 Ltrs capacity, (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F Nipple suitable for HDPE water tank (Minimum weight 15mm-38Gms/20mm-45Gms/25mm-65Gms) for 25mm bore pipe complete all as specified and directed.

S&F 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass complete all as directed and specified.

S&F 'P' or 'S' trap for EWC complete all as directed and specified.

S&F padestal pattern Vitreous china wash down water closet pan white colour with PVC cover sheet plastic water closet seat cover white closed pattern with flat bottom, connection to drain (or out going pipe ) flushing cistern and to flushing pipe antisyphone pipe complete all as specified and directed.

S&F 15mm bore chromium plated two way tab with flange fancy type,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,scrwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15mm bore chromium plated health fucet incl fluxible pipe 1.00 m long wall mounted and brass CP nuts complete all as specified and directed.

S&F PVC valve less syphonic action type flushing cistern 10Ltr capacity low level white.with inlet ball valve float and handle incl brackets. All as specified and directed.

S&F Vetrious china urinal half stall white coloured with urinal spreader of CP for fixing with 15mm dia pipe,( Minimum weight 60 Gms) complete including providing and fixing plugs,beeding urinal against wall in cement mortar 1;2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with spreader, flush pipe,grating and union for discharge pipe ( Excluding of fxing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F vitrios china wash basin white (oval shaped under counter) of size 550mmX400mm complete all as specified and directed.

S&F 15mm dia swan neck piller taps fancy type,cast copper alloy,with capstain heads,chromium plated screwed down high pressure,with or without lettered 'HOT' or 'COLD" with long screwed shanks and fly-nuts screwed complete all as specified and directed.

S&F waste fitting 32mm bore,brass,chromium plated for basins,urinals etc with long screwed shanks and fly-nuts.flange and bed deal in red lead cement and complete all as specified and directed.

S&F PVC waste pipe for wash hand basin/Urinals complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F for granite (of any type) tiles 20mm thick mechine cut,bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing complete all as specified and directed.

S&F urinal partition with HPL board material 10 to 12mm thick,of size 900x450x350 mm fixed with brackets complete all as specified and directed.

S&F CP fancy type angle cock one way, brass chromium plated, fixed to iron pipe or for unions 15mm bore complete all as specified and directed.

S&F 15mm bore chromium plated two way tab with flange fancy type,cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F brass chromium plated tubuler towal rail,20mm dia D type 60cm long between flanges complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preperation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

M&L for applying evently a tack coat of industrial bitumen 25/85 at the rate of 1.20 Kg per Sqm including cleaning surfaces over bituminous primer complete all as specified and directed.

M&L for APP based polymeric mebrain minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt on not less than150ms/Sqm) land on priimed surface by forced torch application complete all as specified and directed.

M&L for applying two coat of bitumen based aluminium painting over a coat of primer on water proofing treatment with preparation of surfaces as on non assesable area complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty with preparation of newly plaster surface of wall complete all as specified and directed. Note:- Putty will be measured and paid separately

M&L for 1mm thick white cement based wall care putty wherever required complete all as directed and specified.

M&L for preparation of newly plastered surface of wall,pilasters,cornices etc and treatemnet apply two coat of Anti fungal weather coat acrylic emulsion paint over a coat of primer (X2) complete all as directed and specified Make of paint: (a) Asian (Apex ultima).berger weather coat all gaurd. (b) ICI Dulex (Weather sheild Max), (c) Nerolac (Excel total) Make of primer : Asian (X2) or equivalent as approved by GE. Note : (i) Each stages i.e preparation of surfaces, primer application, first coat and second coat of Apex will be passed by Engr-in-Charge (ii) Written warrenty for four years is required to be funished by the contractor for this item.

M&L for mechine pressed precast concrete interlocking paver block using rubberised moulding any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 Grade with gray and no pigment over ind including 30mm thick dry screened sand complete all as specified and directed.

M&L for PCC (1:3;6) type C1 (using 20mm graded stone aggrgate) as in mud stops.kerbs etc rounded or chemfered edges complete all as specified and directed.

M&L for PCC(1:2:4) type B2 ( using 40mm graded stone aggregate ) as in foundations,filling and mass concrete complete all as specified and directed.

Surface excavation n exc. 30cm deep and avaraging 15cm deep and getting out in soft/loose complete all as specified and directed.

M&L for construction of soakage well of complete of size 3.00m Dia X3.00m deep complete including excavation in ordinary soil, foundation in PCC 1:3:6 wells of Honey comped and solid in M-25 design nix concrete,including intercepting chember,screen chember brick work in cement mortar 1:4 , RCC cover slab in M-25 design mix, RR measonary, filling with brick bats, complete all as specified in drawing No TD-DRG NO CEJZ/TD/sheet No 1/1 dated 05/05/2000 complete all as specified and directed.

M&L for construction of septic tank for 100 users complete including excavation in ordinary soil, foundation in PCC 1:2:4, brick work in cement mortar 1:4 slab covers including RCC precast manholes cover having 6mm plate embedded all around / Fibre reinforced cover with angle iron frmae Vent shaft and sludge chembers etc. complete for 100 users, complete all as specified in drawing No TD-TRG NO CEJZ/TD/57 sheet No 1/4 to 4/4 dated 05/05/2000 complete all as specified and directed.

M&L for concrete bed 1:4:8 type D2 (40mm graded stone aggregate) for 150mm bore to drain pipes including packing under & haunching against the sides of pipes after thay are laid and tested complete all as specified and directed.

M&L for reinforced concrete pipes, class NP2 laid and jointed complete with coller for dia 150mm bore complete all as specified and directed.

Returing filling in including spreading,levelling watering and well ramming in layers n exc. 25cm in depth complete all as specified and directed.

M&L for cutting/filling and connecting into existing manholes for connecting new sewage line 150 mm bore (internal dia of pipe ) incl making good to disturbed benching and haunching, plaster etc and forming new branch channel ( ½ round of ¾ section) if required in cement concrete 1:2:4 type B1 and smooth finished , reforming benching as required and as directed for internal dia for the following pipe. Note: Each Manhole shall be measured under this item.

Surface dressing n exc. 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for 100mm thick cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in subbase etc complete all as specified and directed.

M&L for stone dust under floors or in foundation including watering and considaration spreading and levelling in layers n exc. 25 cm thick complete all as specified and directed.

M&L for 80mm thick Machine pressed precast concrete interlocking paver block fixing with grey cement and pigments of " I " shape or as approved by GE ,and any colour and size confirming to IS 15658-2006 of M-40 Grade set , laid over 50 mm (average) thick dust sand cushioning, filling of joints with sand & compaction using surface vibrator after filling of joints lain in any pattern as decided by Engineer-In-Charge including packing of sides by cement concrete finishing surface even and smooth complete all as specified and directed. Note : Sand cushioning will be measured and paid separately .

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for brick work with modular size sub class 'B' burnt bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for PCC (1:3:6) type-C2 using (40mm graded broken stone as in surface channel and drain including necessary form work complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on any faces of brick or concrete surfaces finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for cement concrete 1:2:4, type B1(using 20 mm graded stone aggregate) as in copings including formwork complete all as specified and directed.

Extra for forming fair finished drain or channel, 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete all as specified and directed.

M&L for Point wiring with FR LS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc complete all as specified and directed for the following:- Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .

(a) One light point controlled by one switch

(b) One Exhaust fan point controlled by one switch

(c) One 5amps socket out let point controlled by one switch on same board with other switches.

(d) One 5amps socket out let point on independent board controlled by one switch.

All as per item No 97.00 above but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F switch piano flush button single pole one way 6 Amp 240 volt complete all as specified and directed.

S&F socket outlet flush type 5 pin, 6 amps, 230 volts complete all as specified and directed.

S&F switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed.

S&F socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

S&F ceiling rose surface bakelite three terminal complete all as directed.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro/Crompton as approved by GE

S&F integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed . Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro/Crompton as approved by GE

S&F LED street light fittings 1x35 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed . Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2 as approved by GE.

S&F double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F MCB TPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan 250mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model: Ventil Air-DX white or equivalent in /Bajaj/Crompton as approved by GE.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type c-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS TMT bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.

Supply, laying, testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 4 core x 16 Sqmm complete all as specified and directed.

Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in any type of soil complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply laying and jointing GI pipe 'light grade' 40 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

M&L for clean and dry sand (un-washed) in trenches including spreading and levelling for cushioning of UG cable complete all as specified and directed. Note: Punned thickness will be measured

M&L for bricks slightly over burnt (kiln burnt) , modular bricks , best quality, locally available , laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection complete all as specified and directed.

M/S Sunshine Construction (BID ID -3132898)

M/S UnitedConstruction (BID ID -3123682)

sunway associates (BID ID -3131962)

Goyal Construction (BID ID -3132999)