Jehanabad-Provision of Office and Quarter for ADEN/JHD

Item Breakup - B-Schedule-B

local sand, with common burnt clay non modular bricks. Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 11.3 finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone Sqm 160 545 87200 47 aggregate 11.37S CERAMIC GLAZED TILES 11.37 Providing and laying Ceramic glazed floor tiles Sqm 50 935.6 46780 of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid 48 on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 11.41S VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid 11.41 on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 49 11.41.2 Size of Tile 600x600 mm Sqm 80 1416.65 113332 12.0 ROOFING Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.50 Providing and fixing precoated galvanised iron Sqm 50 671.55 33577.5 profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 50 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY 13.0 FINISHING 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 51 13.1.1 1:4 (1 cement: 4 fine sand) Sqm 1500 294.85 442275 CEMENT PLASTER WITH A FLOATING COAT OF 13.7S NEAT CEMENT 12 mm cement plaster finished with a floating 13.7 coat of neat cement of mix : 52 13.7.2 1:4 (1 cement: 4 fine sand) Sqm 50 361.3 18065 13.16S 6MM CEMENT PLASTER 13.17 6 mm cement plaster 1:3 (1 cement : 3 fine Sqm 1000 334.2 334200 sand) finished with a floating coat of neat 53 cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. 13.25 Extra for plastering: 13.26 Providing and applying plaster of paris putty of Sqm 1400 214.3 300020 2 mm thickness over plastered surface to 54 prepare the surface even and smooth complete. Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 13.42 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. 55 13.42.1 Two or more coats on new work Sqm 1400 92.75 129850 13.44S EXTERIOR FINISHING Finishing with Deluxe Multi surface paint 13.48 system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 Sqm 750 158.95 119212.5 56 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm Applying priming coats with primer of 13.85 approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. Painting with synthetic enamel paint of 13.99 approved brand and manufacture of required colour to give an even shade : 57 13.99.1 One or more coats on old work Sqm 120 86.55 10386 14.0 REPAIRS TO BUILDING 14.26S WOOD WORK 14.29 Providing and fixing M.S. round or square bars Kg 750 99.7 74775 58 with M.S. flats at required spacing in wooden frames of windows and clerestory windows. 17.0 SANITARY INSTALLATIONS Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.1 manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan Each 8 5781.35 46250.8 59 of size 580x440 mm with integral type foot rests DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush 17.2 pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 4 5540.55 22162.2 60 seat and lid 17.7A Providing and fixing wash basin with C.I. Each 7 3459.05 24213.35 brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, 61 cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 17.10 including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board 62 17.10.1.1 510x1040 mm bowl depth 250 mm Each 3 6008.45 18025.35 Providing and fixing P.V.C. waste pipe for sink 17.28 or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 63 17.28.1.1 32 mm dia Each 12 90.95 1091.4 17.31 Providing and fixing 600x450 mm beveled Each 10 1411.15 14111.5 edge mirror of superior glass (of approved 64 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.34 Providing and fixing toilet paper holder : 65 17.34.2 Vitreous china Each 4 463 1852 Providing and fixing soil, waste and vent pipes 17.35 : 17.35.1 100 mm dia 66 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 Metre 80 1018.05 81444 Providing and fixing bend of required degree 17.38 with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.38.1 100 mm dia 67 17.38.1.1 Sand cast iron S&S as per IS - 1729 Each 15 530.7 7960.5 Providing and fixing double equal junction of required degree with access door, insertion 17.41 rubber washer 3 mm thick, bolts and nuts complete : 17.41.1 100x100x100x100 mm 68 17.41.1.1 Sand cast iron S&S as per IS - 1729 Each 22 1038.75 22852.5 17.72 Providing and fixing PTMT towel ring Each 7 204.7 1432.9 trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall 69 face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP 17.73 brass screws with concealed fittings arrangement of approved quality and colour. DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY 17.73.1 450 mm long towel rail with total length of 495 Each 4 573.6 2294.4 70 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 17.79 Providing & fixing white vitreous china water Each 6 15968.65 95811.9 less urinal of size 600 x 330 x 315 mm having 71 antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal. 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing 18.7 the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.-Internal work - Exposed on wall 72 18.7.1 15 mm nominal dia Pipes Metre 40 255.9 10236 73 18.7.2 20 mm nominal dia Pipes Metre 20 325.1 6502 74 18.7.3 25 mm nominal dia Pipes Metre 50 408.55 20427.5 Providing and fixing G.I. pipes complete with 18.12 G.I. fittings including trenching and refilling etc.-External work 75 18.12.1 15 mm dia nominal bore Metre 200 267.5 53500 76 18.12.2 20 mm dia nominal bore Metre 50 315.35 15767.5 77 18.12.3 25 mm dia nominal bore Metre 100 417.95 41795 78 18.12.6 50 mm dia nominal bore Metre 50 654.2 32710 18.15S BRASS FITTINGS Providing and fixing brass bib cock of 18.15 approved quality : 79 18.15.1 15 mm nominal bore Each 19 303.85 5773.15 Providing and fixing brass stop cock of 18.16 approved quality : 80 18.16.1 15 mm nominal bore Each 20 303.85 6077 Providing and fixing gun metal gate valve with 18.17 C.I. wheel of approved quality (screwed end) : 81 18.17.1 25 mm nominal bore Each 20 532.35 10647 82 18.17.3 40 mm nominal bore Each 4 707.3 2829.2 83 18.17.4 50 mm nominal bore Each 6 878.25 5269.5 Providing and fixing ball valve (brass) of 18.18 approved quality, High or low pressure, with plastic floats complete : 84 18.18.2 20 mm nominal bore Each 5 397.45 1987.25 Providing and fixing gun metal non- return 18.19 valve of approved quality (screwed end) : 18.19.1 25 mm nominal bore 85 18.19.1.1 Horizontal Each 3 506.65 1519.95 Providing and fixing uplasticised PVC 18.21 connection pipe with brass unions : 18.21.1 30 cm length 86 18.21.1.1 15 mm nominal bore Each 15 74.8 1122 Providing and fixing C.P. brass shower rose 18.22 with 15 or 20 mm inlet : 87 18.22.1 100 mm diameter Each 7 166.35 1164.45 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and 18.46 making long screws etc. complete (New work) : DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY 88 18.46.1 15 mm nominal bore Each 15 262.3 3934.5 89 18.46.2 20 mm nominal bore Each 10 289.05 2890.5 90 18.46.3 25 mm nominal bore Each 5 369.35 1846.75 18.48 Providing and placing on terrace (at all floor Litre 5000 9.7 48500 levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking 91 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.49S C.P. BRASS FITTINGS Providing and fixing C.P. brass angle valve for 18.53 basin mixer and geyser points of approved quality conforming to IS:8931 92 18.53.1 15mm nominal bore Each 20 500.35 10007 18.59S AIR VALVE & WATER METER (BULK TYPE) 18.65 Providing and fixing PTMT soap Dish Holder Each 7 96.75 677.25 having length of 138mm, breadth 102mm, 93 height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. Providing and fixing PTMT extension nipple for 18.75 water tank pipe, fittings of approved quality and colour. 18.75.2 20 mm nominal bore, weighing not less than Each 5 76.5 382.5 94 40 gms 18.77 Cutting holes up to 15x15 cm in R.C.C. floors Each 10 377.1 3771 and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe 95 etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 20.0 PILE WORK Boring, providing and installation bored cast- in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out 20.2 and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 96 20.2.2 500 mm dia piles Metre 400 2274.25 909700 Total 12999985.95