SPECIAL REPAIR OF BLDG NOT180 AT ILP LOC 54 INF BN TA BIHAR AT BRICHGUNJ MILITARY STATION PORT BLAIR

Amount

Dismantling corrugated or plain steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F Steel works In tubular/ posts/ trusses/ purlin including special shaped washer etc.complete using ERW or induction butt welded tubes conforming to IS 1161-1797 grade St 240 complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc and fixed by riveting or welding or with nut and bolts (including nuts and bolts) conforming to Fe-410-W grade E 251 Quality B complete all as specified and directed.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws complete all as specified and directed.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based plain steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws complete all as specified and directed.

S &F MS work in wind ties for roof including securing bolts complete all as specified and directed.

Taking down of chowkhats or frames not exc 1.5 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down of chowkhats or frames exc 1.5 sqm but not exc 4 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Material and labour for anodized aluminium sections (minimum anodisation 15 micros) for partitions, window and door with frame and shutters fully or partially glazed, side Hung type ( two numbers glazed and gauzed) without sash bars, with panel inserts of sheet glass, gauze including necessary jointing cleats, glazing clips, rubber beading, Neoprene packing, anodized aluminium snap beading, screws,i max hinges, butt hinges etc. The size of aluminium sections shall be all as specified in relevant IS code and SSR part-I and completed all as specified and as directed by engineer-in-charge. (Note: (i) supply only panel inserts of glass/gauze, handles, tower bolts and sliding bolt will be measured and paid separately as supply only. (ii) Weight of aluminium section only shall be accounted for payments purpose. However, until rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts of glass/ particle board/gauze, handles, hinges, sliding bolts, tower bolts etc.)

Supply only 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and directed.

Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each panel complete all as specified and directed.

Supply only 5.5mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each panel complete all as specified and directed.

Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and directed.

S&F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and directed.

S&F 100 mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and directed.

S&F 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and directed.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L for providing 100 mm thick, PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base of floors complete all as specified and directed.

M&L for providing 75 mm thick PCC 1:2:4 type B2 using 40 mm graded stone aggregate as in path complete all as specified and directed.

M&L Chequered Cement concrete tiles 20cm x 20cm x 25 mm thick set, jointed and pointed neat cement slurry in floor with grey cement and pigments , incl CM (1: 4) 20 mm thick screed bed complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

Dismantling boarding of any description, fixed in any position with nails/screws complete all as specified and directed.

Material and labour for false ceiling with aluminum grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces all as specified and directed by Engineer-in-Charge.

Dismantling any type of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 100mm thick cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) in sub base of flooring complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 10 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and directed.

Taking down cement plaster of any description from wall/ceiling including raking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition of PCC Block walling built in CM 1:6 complete all as specified and as directed.

M&L for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6, type C1 (using 20mm graded stone aggregate), exc. 10cm in width, set in CM 1:4 all as specified and as directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L Complete removal of existing treatment and applying two coats of OBD over a coat of primer complete all as specified and directed.

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) incl preparation of surfaces complete all as specified and as directed by Engineer-in-Charge. (Make Apex Ultima)

M&L Painting to new steel and iron surfaces of exc. 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and as directed.

M&L for preperation of old painted steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint including preparation of surfaces all as specified and directed.

Taking down carefully, copper/aluminium point wiring (Light, fan, scoket or power) complete, including fittings and fixtures such as switches, ceiling roses, sockets etc., and making good disturbed surfaces of walls floors, etc., complete all as specified and as directed by Engineer-in-Charge.

M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover/Pre moulded PVC switch board for housing the switches, socket outlets, fan regulators etc., all as specified and as directed for the following: - One light point controlled by one way switch

One ceiling fan point controlled by one way switch

One 3 pin switch socket outlet point 5 amps on same board with other switches.

One 3 pin switch socket outlet point 5 amps on independent board.

All as per item at sl No.40.00 here in before but with copper conductor cable for one 3 pin socket outlet, 15 amps independent, with cable 4 Sqmm size and 4 Sqmm earth continuty conductor, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush type, complete all as specified and as dircted by Engineer-in-Charge.

Supply and fix switch socket outlet, 2 in 1, 3 pin 15 and 5 amps, controlled by one switch flush/box type complete all as specified and as directed by Engineer-in-Charge.

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge

Supply and fix energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

S&F 25 W New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB, complete all as as specified and as directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I complete all as specified and directed.

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out of Soft/loose Soil

Returning, filling in, including spreading, leveling watering and well ramming in layers not exceeding 25cm soil / hard dense soil.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point Soft Soil / hard dense soil

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of 50 mm bore size.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

Gulmarg Electrical Service

M/s G K Enterprises

M/s Kamal Electrical

M/s Saina Enterprises

P Babu

Bismi Builders & Enterprises

DEEPAK AGENCIES