REPAIR/REPLACEMENT OF INTERNAL WIRING AT OFFICE AREA , OTM ACCN GUARD POST AND OTHER TECHNICAL AREA INSIDE DEPOT AREA UNDER GE BHARATPUR

Amount

Disconnecting & taking down the ceiling fan of any sweep for carried out preventive maintenance and re hanging the same after cleaning the dust etc with air pressure, cotton cloth & brush, taking out ball bearing and bush, cleaning with kerosine oil, lubricating greasing, oiling, cleaning to winding including supply and replacement of nuts, bolts, rubber seal, split pin, connector and copper cable PVC size 3 core 0.5 Sqmm upto required lenght from ceiling rose to connector of ceiling fan including , connecting up and testing complete all as specified and directed.

M&L for spray painting of ceiling fan of any sweep complete with blades, down rod etc with synthetic enamel paint of approved colour by spraying including filling cavaties with filler, preparation of surfaces cleaning all dust etc and writing of MES No of size not exc 5cm high using black enamelled paint complete all as specified and directed. Note : Cost of disconnecting & taking down and rehanging is considered under item no 1

M&L for cutting and dismantling the existing winding of ceiling fan of 1200mm sweep and rewinding with super enamelled copper winding wire of suitable gauge including varnishing, lubricating, greasing, oiling and testing including replacement of ball bearing-02 Nos if required complete all as specified and directed by Engr-in-charge. Note : Cost of bearing deemed to be included in quoted rate.

Description all as per ser item No 03 here in above but 1400mm sweep ceiling fans including replacement of ball bearing-02 if required Nos complete all as specified and directed by Engr-in-charge. Note : Cost of bearing deemed to be included in quoted rate.

Supply and replacement of following parts/components suitable for ceiling fan 1200/1400mm sweep complete all as specified and directed :-

Capacitor 2.5/3.5 mfd, oil filled, 400V AC, 50 HZ, 85 degree C ISI marked Make : Asian/Unistar/Usha.

Hanging clamp complete with rubber real Make as existing /sample kept in AGE E/M office complete all as directed by Engr-in-charge.

Fan Hook complete as standard real existing in market for fixed in GE Pipe/Existing Channel

Ceiling fan blade suitable for ceiling fan of any sweep (set of three blades)

Down rod 50 cm long 15mm internal dia heavy duty duly painted including hanging clamp, rubber ring, nut and bolts complete with canopy

Disconnecting & taking down the exhaust/wall fan of any sweep for carried out preventive maintenance and re hanging the same aftercleaning the dust etc with air pressure, cotton cloth & brush, taking out ball bearing and bush, cleaning with kerosine oil, lubricating greasing, oiling, cleaning to winding including supply and replacement of nuts, bolts, rubber seal, split pin, connector and copper cable PVC size 3 core 0.5 Sqmm upto required lenght from ceiling rose to connector of exhaust/wall fan including hanging, connecting up and testing all as directed. Note for Srl item No 01 and 6 here in before : (i) Minor parts such as nut, bolt, washer,rubber seal, split pin, connector copper cable pvc insulated 0.5 sqmm 3 core are deemed to included with unit rate of item. (ii) Parts/components replaced other than mentioned above will be measured and paid separately under respective items. (iii) The services of ceiling fan/Exhaust fan carrying out door to door.(iv) After completion of work all fans shall be tested to the entire satisfaction of Engr-in-charge

M&L for spray painting of exhaust/wall fan of any sweep complete with blades, down rod etc with synthetic enamel paint of approved colour by spraying including filling cavaties with filler, preparation of surfaces cleaning all dust etc and writing of MES No of size not exc 5cm high using black synthetic enamelled paint all as directed.

M&L for cutting and dismantling the existing winding of exhaust/wall fan of any sweep with super enamelled copper winding wire of suitable gauge including varnishing, lubricating, greasing oiling testing incl replacement of ball bearing/GM bush as required complete all as specified and directed by Engr-in-charge.

Supply and replacement of following parts/components suitable for exhaust fan 200 to 450mm sweep (PVC & Steel ,body) complete all as specified and directed:-

Capacitor 4 mfd, oil filled, 400V AC, 50 HZ, 85 degree C ISI marked Make : Asian/Unistar/Usha.

Fan blade set (set of three) for exhaust fan of 380mm sweep.

Fan blade set (set of three) for exhaust fan of 450mm sweep.

Exhaust fan mounting bracket incl nuts,fastners of size 380-450mm sweep

Exhaust fan motor of 200-300mm sweep as per existing PVC exhaust fan

Exhaust fan motor of 300-450mm sweep as per existing steel body exhaust fan

Louvers and shutters of PVC/ MS as per existing exhaust fan

S&F new 3 pin plug top 16 amps, 230 volts, ISI marked including taking down U/S plug top complete all as specified and directed.

S&F new 3 pin plug top 5 amps, 230 volts, ISI marked including taking down U/S plug top complete all as specified and directed.

Taking down of old unserviceable copper / aluminium flame proof point wiring (light,socket) with conduit complete including fitting & fixture such as switches, ceiling roses, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good disturbed surfaces of walls, floors etc (For ESH shed area) complete all as specified and directed.

Taking down old U/S sub main wiring and service wire of any size & make complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, bell,same board, independent or power) complete fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of wall, floor & ceiling etc complete all as specified and directed. (For OTM Accn)

Blank

Dismantling of old U/S rusted main switch/DB of any size capacity and make complete all as specified and directed..

M&L concealed point wiring complete with two runs of 2.5 sqmm, single core multi stranded copper conductor PVC insulated and unsheathed FRLS cable, 1100volts grade IS-694 marked drawn through and including rigid steel ERW conduit min 20mm dia ( stove enameled) heavy duty as per IS 9537 Part I and including all necessary flame proof , weather proof conduit accessories and fitting fixed to concealed in wall/ceiling with teflon tape sealed in all threaded joints in conduit and fittings for light points and including 2.5 sqmm (or nearest equivalent Metric size) single core multi stranded copper conductor PVC insulated and unsheathed cable 1100 volts grade continuity wire (connecting to earth dolly) & wiring shall be suitable for flame froof ESH shed area as per STEC-7 for the following :-

Two light points controlled by one switch/MCB

One light points controlled by one switch/MCB

M&L submain wiring in existing conduit complete with 2.5 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 2.5 Sqmm copper cable for earth continuity conductor complete all as specified and directed. Note :- Two runs of single core of 2.5 sqmm, one run of 2.5 sqmm earth continuity conductors shall be measured as one unit run length.

M&L surface submain wiring complete with 2.5 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 2.5 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 20 mm dia rigid steel ERW conduit min 20mm dia ( stove enameled) heavy duty as per IS 9537 Part I and including all necessary flame proof , weather proof conduit accessories. Note :- Two runs of single core of 2.5 sqmm, one run of 2.5 sqmm earth continuity conductors and one run of 20mm dia rigid steel ERW conduit with accessories shall be measured as one unit run length.

M&L concealed point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe size not less than 20 mm dia with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface and making good the disturbed surfaces of wall/ceiling by means of Wall putty and matching colour of existing wall, PVCsleevel/dash fastners with cadmium plated screws including suitable size of PVC boards/ sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connected to earth dolly complete all as specified and directed for the following (for OTM accn) :-

One light point controlled by one way switch.

One fan point controlled by one way switch.

One 3 pin 6 Amp socket point outlet on the same board with other switches

One 3 pin 6 Amp socket point outlet on the independent board

One bell/buzzer point controlled by one push button.

All as per item No 20 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified and directed.

M&L point wiring complete with 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in and including PVC casing and caping double locked box type with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the surface of wall/ceiling by means of PVCsleevel/dash fastners with cadmium plated screws including suitable size of PVC boards for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly complete all as specified and directed for the following :-

One light point controlled by one way switch.

One fan point controlled by one way switch.

One 3 pin 6 Amp socket point outlet on the same board with other switches

One 3 pin 6 Amp socket point outlet on the independent board

All as per item No 22 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps switch socket outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified and directed.

S&F ceiling rose surface bakelite three terminal ISI marked including suitable size of PVC board make : Anchor code No 3290 penta or equivelent complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type multi purpose flush type 230 volt complete all as specified and directed.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified and directed.

S&F switch piano flush button single pole one way 16 Amps 230 volt grade complete all as specified and directed.

S&F socket 3 pin 16A, flush type

S&F bell push flush type 5 Amps 230 volts grade.

M&L bell multi musical type 230 volts grade.

S&F step type electronic fan regulator EME type 450 watt.

M&L concealed submain wiring complete with 2.5 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 2.5 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 20 mm dia with all PVC accessories. Note :- Two runs of single core of 2.5 sqmm, one run of 2.5 sqmm earth continuity conductors and one run of 20mm dia PVC conduit with accessories shall be measured as one unit run length.

M&L concealed submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 20 mm dia with all PVC accessories complete all as specified and directed. Note :- Two runs of single core of 4 sqmm, one run of 4 sqmm earth continuity conductors and one run of 20mm dia PVC conduit with accessories shall be measured as one unit run length.

Supply and fixing of distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt, 415V of the following DBs

4 way TPN with busbar 415 volts (double door)

8 way SPN with 200 amps rated busbar 240 volts (double door type).

4 Way SPN with 200Amp rated busbar 240V (Double door type)

S&F in repair MCCB's, MCB's of following capacity complete all as specified and directed:-

MCB TPN 63 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

MCB TPN 32 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

MCB SP 6-32 Amps, 240 volts,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

MCB SPN 6-32 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

MCB SPN 40 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

Supply and fixing in replacement of LED flameproof tube light fitting CMRI certified 1x20W LED tube light fixture complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size of Cat Part No SSPL/FF/1271 lamp of Shyaam switchgear (P) Limited or equivalent model of flexpro/Crompton Greaves/Phillips as approved by GE complete all as specified and directed.

Supply and fixing in replacement of LED flameproof tube light fitting CMRI certified 2x20W LED tube light fixture complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size of Cat Part No SSPL/FF/1271 lamp of Shyaam switchgear (P) Limited or equivalent model of flexpro/Crompton Greaves/Phillips as approved by GE complete all as specified and directed.

Supply and fixing in replacement of 20 watt LED tubelight fitting retro fit type 4 feet long with LED rod, replacable rod type complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed. make: Cromption or equivelent in Phillips/Surya/Helonix/Havells

Supply and fixing sensor based 20 watt LED tubelight fitting batten type 4 feet long with rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed. Make: Cromption Cat No:R20RBA or equivelent in Phillips/Surya/Helonix/Havells

S & F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all incl 9watt LED lamp complete all as specified and directed by Engineer-in-charge.

S&F modular sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 25 Amps, 240 volts complete all as specified and directed.

S & F street light GI bracket of 0.6 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 40 x 6mm including nuts bolts & washers complete necessary fixing arrangements on pole complete all as specified and directed.

S&F 35/36 watts LED street light fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light source with warranty option of 5 years and suitable drivers etc and connecting with 2.5 sq mm solid aluminium conductor PVC insulated twin core weather proof cable from fittings to over head lines or to the jucntion box and fixing to complete all as specified and directed , Make crompton Cat: LSTS-36 CDL-M or equivalent in Bajaj/Havells/Phillips

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed. Make crompton or equivalent in Bajaj/Havells/Phillips

M & L for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate, depth not less than 2.25 Mtr below the ground level connected to GI earth wire 4mm dia by means of bolts, nuts and washers protected by GI tubing light grade 15 mm dia uptoTest point, 20 mm dia watering pipe with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm complete all as specified and directed by engr in charge (Note:- Up to7.5Mtr length of pipe of 15 mm dia and GI wire shall be deemed tobe included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5) will be measured separately under respective item

Supply of Lithium based Energy efficient Integrated Solar Street Light of 32 Watt" in single FRP body with duly polyurethane coating (camouflage color), encases with monocrystalline solar PV panel of 65-67WP , Lithium Battery 11.1/12.8V, 33.0AH with inbuilt BMS, IP 65 high brightness W-led(160-180LM/WATT) lamp with aluminum reflector for better light distribution, CRI>70, Color Temperature 5700K-6500K, Microcontroller based charge controller cum driver, automatic dimming function (first four hours at full brightness& rest of the time at lower light level with PIR Motion sensor) . Dusk to Dawn operation, suitable to working temperature: (-) 10C to (+) 55C, weight not more than 16-18KG with adjustable MS clamp suitable for pole/wall mounting etc complete all as specified and directed. Protections: Short Circuit, overload, Reverse polarity and battery protections, Firm should provide vital parameters test report from NABL accredited lab and should be of made in india with CE & ROHS compliant. Make Axxon (AXN-32W)

Blank

Supply and fixing in repair Gang box switch socket combition for 5 Amp complete all as specified and directed.

Supply and fixing in repair Gang box switch socket combition for 15 Amp complete all as specified and directed.

Supply and fixing in repair 1.5sqmm copper conductor complete all as specified and directed.

Supply and fixing in repair capacitor 2.5/3.5/4.0 mfd 240V ISI mark complete all as specified and directed.

Supply and fixing in repair Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type multi purpose flush type 230 volt complete all as specified and directed.

Supply and fixing in repair switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified and directed.

Supply and fixing in repair Socket outlet 3 pin 15 amp flush type multi purpose flush type 230 volt complete all as specified and directed.

Supply and fixing in repair switch piano flush button single pole one way 16/15 Amps 230 volt grade complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtrs wide and not exc. 1.5 Mtr deep and getting out for taking out/laying cable, poles & stay etc complete all as specified and directed.

Demolition of Cement Concrete (un-reinforced) in ground floors and pavings not exc 15cm thick( below or above ground floors) complete all as specified and directed.

Returning, filling in including spreading leveling, watering and well ramming in layers not exc 25 cm thick after the cable have been laid and tested complete all as specified and directed.

Removal of excavated surplus soil to a distance not exc. 50 Mtrs and depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cable provided with layer of sand (8cm deep before laying the cable and 15 cm deep after laying the cable ie total 23 cm) complete all as specified and directed. Note : Punned thickness shall be measured

Supply and laying of sub class 'B' bricks in trenches over cables for protection cover across the length of cable complete all as specified and directed.

Driling hole in hard standing / road for laying of pipe for protection of cable etc by adopting method of horizontal manual drilling (trenchless technology) without disturbing the top surface or cutting and making good the disturbed surface to the existing surface complete all as specified and directed.

Supply and laying in replacement of GI tube light grade 40 mm bore complete all as specified and directed.

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole complete all as specified and directed of the following sizes :-

16 Sqmm 4 core

16 Sqmm 2 core

10 Sqmm 2 core

PD GUPTA AND COMPANY

M/s Ranaji Construction Co

GANGA CONSTRUCTION