Furniture and Internal Fit-outs works at JNV Mamit Mizoram

SCHOOL BUILDING

(iii)TEACHER TABLE :Supplying and installation of knock down type Office Table made of Pre-laminated MDF board with decorative lamination on one side and balancing lamination on other side top of size 1200 X 600 X 750 mm. Worktop shall be rounded in all four corners and should have an overhung of 50mm alongwith one drawer unit made of 0.5mm thick CRCA Steel sheet. The table top shall be supported over legs consists of 4 Powdered coated MS legs with connected beams with pipe size 25x25x1.2 mm thick.

(iv)Teachers Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished Finish

(B) PRINCIPAL AND VICE-PRINCIPAL ROOM

Supplying and installation of site knock down type Office Table as per approved design and directrion of Engineer-in-charge. Work Top - Work top shall be made 25mm thick Pre-laminated MDF board with decorative lamination on one side and balancing lamination on other side confirming to IS 12406:2003 with post forming on front, back and machine pressed PVC egde banding 2mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. Table top shall have 75mm overhung on front and 25mm overhung on sides. Understructure- C-type leg shall be made of tubular section of 50mm x 50mm x 1.6mm (wall thickness) thick vertical member and 40mm x40mm x1.6mm (wall thickness) Horizontal M.S. pipe confirming IS-Grade 4932 shall be finished with epoxy polyster powder coated DFT 50-60 Micron. The legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 15mm. The cross members shall be mounted by end brackets made of 3mm thick CRCA steel sheet confirming IS 513: 2008 and finished with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993. Wire management - Electrical wires shall be carried from horizintal/ vertical duct made of 0.7mm CRCA steel sheet confirming to IS 513:2008. The switch plate or grommet depending upon requirement shall also be provided for electrical/LAN connection on table top. Modesty Panel -Modesty Panel of height 450mm shall be made of 1.5mm thick CRCA sheet sheet confirming to IS 513: 2008 and shall be finised with epoxy polyster powder coated DFT 50-60micron. Storage body- Storage top shall also be made of 25mm thick Pre-lam MDF board confirming to IS 12406:2003 with post forming on two sides and machine pressed PVC egde banding 2 mm thick glued with industrial adhesive and diffused with board monolithically on other two sides. The body of storage units shall be made of 0.8mm thick CRCA steel Sheet and skirting shall be of 1.2mm thick CRCA steel sheet confirming to IS 513: 2008 finished with epoxy powder coated of DFT 50-60 Micron confirming IS 13871:1993. Internal Shelves shall be also made up of 0.8mm CRCA steel sheet confirming to IS 513: 2008 and shall be mounted with the Metal shelf support pin made of 2mm thick CRCA Steel sheet with Nickel or Chrome plating. M10 screw leveler is given with height adjustment up to 12mm to 15mm. (ii) VICE-PRINCIPAL ROOM TABLE Table of Size 1650mm (W) x 900mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 750mm (H) and Back Storage 1650 mm (W) x 450mm (D) x 750mm (H) as per specifications above.

(v) VICE-PRINCIPAL ROOM CHAIR High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm , Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade, Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS 202 Polished Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .

(D) STAFFROOM

(iii) Chair Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished Finish

(iv) PERSONAL LOCKER UNIT FOR PRINCIPAL AND VICE PRINCIPAL ROOM Supplying and installation of Metal Lockers with Cam Lock one unit consiting of 380mm (W) x 450mm (D) x 1800 mm (H) with 4 Lockers. Body-LH and RH Side and back panel is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008. Shelf hanging bracket is welded on both the side panel by spot welding. Shelf hanging bracket is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008. front frame, top and bottom part made up 0.8mm thick CRCA steel sheet confirming to IS 513:2008 and horizontal part is made up 0.8 mm thick CRCA Steel sheet confirming to IS 513:2008. On a front frame horizontally provision is given at a common distance to hold shutter bracket. Locker’s top is made up of 0.8mm thick CRCA Steel sheet confirming IS 513:2008 which is having standard dimension 375 x378mm. Shelf is also made up of 0.8 mm CRCA Steel sheet confirming to IS 513:2008. Shutter- Is made up on 0.8mm thick CRCA Steel sheet confirming to IS 513:2008. All the shutter are hung on shutter pin and shutter bracket, louvers are given in shutter for air flow. PVC flush handle and name plate is used for handling and for name plate tagging. Standard locking arrangment is used for locking each shutter. The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder coating of DFT 50- 60 Micron confirimg to IS 13871:1993.

(E) LIBRARY

(iii) TABLE (SEATING CAPACITY AS PER ACTUAL REQUIREMENT) Supplying and installation of a modular, knock-down center island table sized approximately 3600 mm in length (adjustable to actual requirements) by 1350 mm in width and 750 mm in height, constructed from high-quality 25 mm thick commercial grade plywood or BWR (Boiling Water Resistant) grade plywood with decorative lamination on visible faces and balanced lamination beneath for enhanced strength and moisture resistance. All edges are sealed with 2 mm thick machine-pressed PVC edge banding bonded with industrial adhesive to ensure a seamless, monolithic appearance. The gable ends are fabricated of the same 25 mm thick commercial grade plywood with decorative lamination on both sides and matching edge banding for consistent aesthetics and superior durability. Modesty 18mm matching laminate. The table shall have an underbody vertical support panel running continuously along its length to enhance stability and strength. The understructure uses precision-cut, laminated plywood panels assembled with knock-down fittings for ease of installation and future reconfiguration, ensuring superior load-bearing capacity and long-term durability. A concealed wire management system beneath the worktop integrates pre- laminated plywood cable trays or high-quality plastic trays fixed with durable brackets, complete with provisions for switch plates and grommets to facilitate safe, organized routing of electrical and data cables. All surfaces are finished for scratch and stain resistance with anti-fungal and moisture-resistant properties, and installation will follow best woodworking practices, with final dimensions and seating capacity determined by the actual site layout.

(iv) Chair Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS 202 Polished Finish

(F) COMPUTER LAB

(i) COMPUTER WORK STATION Supplying and installation of knock down type Dual Computer Work Station of unit Size 1500mm (Length, actual Length may vary as per actual site requirement) x 600m (W) x 750mm (H) for two students Work Top- Work top shall be made 25mm thick Laminated Plywood with decorative lamination on one side and balancing lamination on other side confirming to IS 12823: 1990 with 2mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on all sides. Understructure supporting frame consist of laminated Plywood Gable ends of 18mm Wire management-The Vertical /Electrical duct & Horizontal Cable tray ( wire carriers) are made of CRCA steel sheet & fixed to the understructure below worktop with specially designed brackets. Provision for fixing Switch plates are privided in the cable tray for easy access through wire mangaer or PVC grommet.

(ii) COMPUTER CHAIR FOR STUDENT Medium Back Revolving Chair, Overall Dimension:- 720W ±10 x 720D ±10 x 1070H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3 , Back of High back chair is made of Injection moulded PP material structure ,combination of upholstered with Mesh fabric , Seat and back connected through metal powder coated plate, Adjustable Lumber support upholstered with fabric , Seat Size:- 470W ±10 x 470D ±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x605H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade,Armrest: PU Padded Adjustable armrest fixed on frame,Chair Base & Wheels: Metal chrome plated Chair Base consists of 5 prongs with 650±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor.

(F) LABORATORIES

Supply and installation of Glass-door Storage of Size 916 mm (W) x 486mm (D) x 1980mm (H). It should have shelf thickness of 0.7mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear glass of 3.0mm thick and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-60 Micron confirimg to IS 13871:1993

KITCHEN & DINING