Special repairs to working women Hostel building at Rajaji Nagar, Lawspet, Puducherry by the PWD, Puducherry

Amount

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos / lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. - with chlorpyriphosl lindane E.C.20% with 1% concentration.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane ( in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

Providing and fixing 18mm thick gang saw cut, mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters,window sills,facias and similar locations , of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Raj nagar plain white marble / Udaipur green marble / Zebra black marble - area of slab over 0.50 sqm

Providing edge moulding to 18mm thick marble stone counters ,vanities etc., including machine polishing to edge to give high gloss finish etc. complete - Marble work

Providing wood work in frames of false ceiling , partitions etc. sawn and fixed in position - Vengai wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) non - decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing 40 X 5 mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium tower bolts, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868), transparent or dyed to required colour or shade , with necessary screws etc. complete - 250 x10 mm

Providing and fixing aluminium handles, ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Single rubber stopper

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 48 x 40 mm

Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness, fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1:4 ( 1 cement : 4 coarse sand) - 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting , dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs,including rubbing and polishing complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 200 x 300 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 200x300 mm

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make (Nitco / Kajaria) in colours such as white, Ivory, Grey, Fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete

Providing and laying vitrified floor tiles of size 600 x600 mm (thickeness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile600x600mm

Providing and laying vitrified tiles of size 600 x600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to IS : 15622 , of approved make , in all colours & shade, in skirting ,riser of steps , over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand), including grouting the joint with white cement & matching pigments etc.complete - size of tile 600x600mm

Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over mm thick cement mortar 1:4 (1 cement : 4 sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \ Dazzle \ Technic)

Providing and fixing PVC corner beading of required size to suit the thickness of the wall tile at the corner joints of dado works

15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand)

Finishing walls with textured exterior paint of required shade - New work (Two or more coats applied @ 3.28 ltr / 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - with cement mortar 1:4 (1 cement : 4fine sand)

White washing with lime to give an even shade - Old work (two or more coats)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete

Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacture's specification - Two or more coats applied on walls @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm

Cleaning of under ground sump , Over Head R.C.C. tank (independent staging) including disposal of slit and rubbish . The cleaning shall consist following operations: i) Tank shall emptied of water by pumping and bottom shall be cleaned of slit and other deposits. Ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. Iii) Chlorination of RCC internal surface by liquid Chlorine.iv) the treated surface shall be dried using air jetting and all loose particles shall be removal from the surface.v)Finally the surfcae shall be treated with ultraviolet radition etc.

Dismantling W.C.Pan of all sizes including disposal of dismantled materials i/c malba all complete

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles above 25 mm and upto 40mm

Poilising the existing mosaic floor with Power polisher to a high degree of polish as to be perfectely smooth

Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 470x420 mm bowl depth 178mm

Extra for using coloured W.C.pan instead of white W.C.pan - Orissa pattern W.C.pan 580x440mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexiple pipe - 40mm dia

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112 mm distance fromwall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88mm, weighing not less than 170 gms

Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall - 20 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete - external work - 25mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 25mm nominal bore

Providing and fixing C.P.brass shower rose with 15 or 20 mm inlet - 100 mm diametre

Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore,165 mm long , weighing not less than 110gms

Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore, 90 mm long , weighing not less than 93 gms

Providing and fixing PTMT grating of approved quality and colour - rectangular type with openable cirucular lid - 150mm nominal size square 100mm diametre of the inner hinged round grating

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Supplying and fixing C.I.cover without frame for manholes - 455 x 610 mm rectangular C.I.cover (light duty) the weight of the cover to be not less than 23 kg

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm

SATHYAMURTHY

sabastinmartial

T.MOORTHY

Manavazhakan