Construction of Degree College G plus 1 at Ramkot Billawar including Chowkidar Quarter and Canteen Phase-1st

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth,1.5mtr in width as well as 10 Sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50m, disposal earth to be leveled and neatly dressed:

a) All kinds of soi = 50%

b) Ordinary rock = 20%

c)Hard rock(Blasting Prohibited) = 30%

Earthwork in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10sqm on plan, depth upto 1.5mtr. including disposal of excavated earth upto 50mtr from cutting edge, disposed earth is to be leveled and neatly dressed in:

a) All kinds of soi = 50%

b) Ordinary rock = 20%

c)Hard rock(Blasting Prohibited) = 30%

Extra for every additional lift of 1.5 M or part therefore in all kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed (including all leads and lifts carriages of material by MT/HL).

Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) excluding the cost of centering, shuttering, finishing and reinforcement. All work upto plinth level. (including all leads and lifts carriages of material by MT/HL).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL).

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) excluding the cost of centering and shuttering. All work upto plinth level. (including all leads and lifts carriages of material by MT/HL).

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 upto plinth level in cement mortar 1:4 (1 cement : 4 fine sand) (including all leads and lifts carriages of material by MT/HL).

Providing and laying DPC 50mm thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size crusher aggregate) (including all leads and lifts carriages of material by MT/HL).

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in cement mortar 1:6 (1 cement : 6 fine sand) (including all leads and lifts carriages of material by MT/HL).

Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) (including all leads and lifts carriages of material by MT/HL).

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand) (including all leads and lifts carriages of material by MT/HL).

Extra for half brick masonry in superstructure above plinth level upto Floor V level (including all leads and lifts carriages of material by MT/HL).

Providing and laying Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) in suspended floors, balconies, landings and staircases having 15 degree slope. upto floor five level excluding the cost of centering and shuttering (including all leads and lifts carriages of material by MT/HL).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Suspended floors, roofs, landings, balconies and access platforms.

Columns, pillars, piers, abutments, posts and struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Retaining walls, return walls, wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc.

Weather shade, chajjas, corbels etc. including edges.

Stairs (excluding landings) except spiral stair cases.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size) in R/Wall/Return Wall, columns etc. excluding the cost of centering and shuttering, all works upto floor V level (including all leads and lifts carriages of material by MT/HL)

6mm thick cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand) (including all leads and lifts carriages of material by MT/HL)

15mm cement plaster on the rough side of single or half brick wall of mix in 1:6 (1 cement : 6 fine sand) (including all leads and lifts carriages of material by MT/HL)

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand). (including all leads and lifts carriages of material by MT/HL)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand) (including all leads and lifts carriages of material by MT/HL)

15mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating cost of neat cement on the rough side of single or half brick wall (including all leads and lifts carriages of material by MT/HL)

18mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 fine sand) top layer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand) for 4cm width (including all leads and lifts carriages of material by MT/HL)

Extra for plastering exterior walls of the height more than 10 Mtrs from ground level for every additional height of 3 Mtrs or part thereof.

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections.

Making of grove 12mm x 10mm between brick and RCC.

Providing and laying 18mm thick Udhaypuri Green Marble /zebra black marble (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels (including all leads and lifts carriages of material by MT/HL)

Providing and laying glossy finished full-body vitrified premium quality floor tiles of 60x60cm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Somany, Kajaria, NITCO and Orient make in colours and shade Ethnic-Berlinetta White, Crown White, Dacia White, Dacia Green, Dacia Pink, Dacia Ivory, Dacia Grey, Dacia Brown, Dacia Pearl, Dezzling White, Evalia, S&P Grey, S&P Brown, Ultra White, Haze Grey and Border of Royale- Crown Mint, Crown Pink, Crown Snow, Micra Brown and Radiant- Lawrence Gold, Lawrence Bianco, Lawrence Grigio, Lawernce Moka, Lawrence Jaisalmer, Nuvro Brown, Nuvaro Mocha, Nuvaro Grey, Nauvaro Nero, Nuvaro Crema, Nuvaro Bianco, Nuvaro Beige laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete (including all leads and lifts carriages of material by MT/HL)

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in all colour, shades except burgundy, bottle green, black of any size as approved by Engineer in charge in skirting, risers of steps and dodos over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete (including all leads and lifts carriages of material by MT/HL)

Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete (including all leads and lifts carriages of material by MT/HL)

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels (including all leads and lifts carriages of material by MT/HL)

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut flamed (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels (including all leads and lifts carriages of material by MT/HL)

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. over item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge (including all leads and lifts carriages of material by MT/HL)

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Precast terrazzo tiles 22mm thick with graded marble chips of size upto 12mm laid in floors and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete with precast tiles on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand). Medium shade using 50% white cement and 50% ordinary cement (including all leads and lifts carriages of material by MT/HL)

Precast terrazzo tiles 22mm thick with graded marble chips of size upto 12mm laid in skirting and risers of steps not exceeding 30cm in height on 12mm cement plaster 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles, excluding rubbing and polishing complete with tiles of medium shade using 50% white cement and 50% ordinary cement (including all leads and lifts carriages of material by MT/HL)

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand). Medium shade using 50% white cement and 50% ordinary cement (including all leads and lifts carriages of material by MT/HL)

Cement concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, but excluding the coat of nosing of steps etc. complete 50mm thick with 20mm nominal size of stone aggregate (including all leads and lifts carriages of material by MT/HL)

Cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 18mm thick (including all leads and lifts carriages of material by MT/HL)

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm. (including all leads and lifts carriages of material by MT/HL)

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm (including all leads and lifts carriages of material by MT/HL)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter (including all leads and lifts carriages of material by MT/HL)

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :-

Coupler 110mm.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed (including all leads and lifts carriages of material by MT/HL)

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand) (including all leads and lifts carriages of material by MT/HL)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) sal wood.

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL)

Providing & fixing glazed shutters 35mm thick for doors, windows and clear story windows using 10Kg/Sqm (4mm thick) glass panes including stainless steel but hinges of size 75mm x 62mm x 2mm of make Kitch, Arch, Blum with necessary stainless screws in second class deodar wood.

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauge of average width for aperture 1.4mm in both direction with wire of dia 0.63mm for doors, windows and clerestory windows with hinges and necessary screws in second class deodar wood.

Providing and fixing of glass panes weighing 13.75 kg/sqm (5.5mm thick) with deodar wood fillets.

Providing and fixing of block door shutters in pine wood filling and finished with 1mm thick laminated on both sides. Door held with 4 No. hinges with necessary screws as per directions of Engineer-in-charge with deodar wood beading of 100mm x 37mm section.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.).

Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work.

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 300x16mm.

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper.

Providing and fixing oxidized M.S. hasp and staple (Safety type) conforming to IS : 363 with necessary screws etc. complete.

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type).

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Orgnic Compound ) contant less then 50grams/liter,of approved brand and manufacture, including applying additional coats wherever required, to achieve even Shade and colour with two coats.

Finishing walls with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litter/10sqm over and including base Coat of watter proofing cement paint applied @ 2.20kg/10sqm.)

Applying priming coat with ready mixed pink or grey of primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work (Wood work).

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade (two or more coats) on new steel work.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately).

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm).

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge with brass cover plate.

Providing and fixing structural glazing on required portion of the building with aluminium section (12 gauze using 5.5mm toughen glass with all necessary fittings) as per direction of Engineer-in-charge.

Maintaining 50mm joint right from foundation to top and allowing its free moment throughout the life span of structure "Providing/Supply of Dura Board HD 100, 50mm, Premounded Compressible filler Board in Black colour manufactured by the Supreme industries Ltd. or equivalent, conforming to MORTH specifications (clause 1015), having minimum density 95 kg/cum, non staining with less than 1% water absorption and compression recovery 93% minimum as per specifications" in the joint through and through (foundation to top) in brick masonary, columns and beams.

Sealing of joint 50mm. Clean the joint both the side and apply Master Brace ADH 2200 adhesive throughly on the clean surface along the joint with spatula and thickness should be 1mm -2mm. Place the Master Seal 1930 10mm on the ADH 2200 on the both sides keeping the centre totally for free movement.

Providing & fixing of white vitreous China pedestal type water closet (European Type) with cistern (A/PHAS-100 +Cat No. 201100 + Cat No. 21054) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.

Providing & fixing of white vitreous China under counter oval wash basin / circular basin (Hindware 10080) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Pedestal Cat No. 11003) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing CP single liver extended basin mixer (height 85mm) without Popup waste system with 450mm long Braided Hoses and brass nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar FUS 290238).

Providing & fixing white vitreous china flat back urinal with automatic flushing systems (Hindware 60021) comprising of all plumbing, electronic and electrical items, CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes, electrically operated solenoid valve, step down transformer, equipment and any other item required to provide satisfactory functioning including necessary wall cutting/ chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-Incharge.

Providing and fixing stainless steel A ISI 304 (18/8)kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610 x 460mm bowl depth 200mm (Pantry).

Providing and fixing, testing and commissioning of C.P brass Sink mixer with regular swinging spout (wall mounted model) with connecting legs and wall flanges complete as required and making good as per direction of Engineer-in-charge (Jaquar Cat No. QQT 7309).

Providing and fixng C.P hand spray with lever control (health faucet) (Jaquar Cat No. ALDCHR-565) and flexible hose 1 Mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-in-charge.

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS : 8931 a) 15mm nominal bore (Make Jaquar FUS 29053).

Providing and fixing C.P brass robe hook (Jaquar Cat No. CAN 1191N) or approved equivalent) fixed to wall / door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.

Providing and fixing recessed liquid soap dispenser with glass bottle (Jaquar Cat No. ACN 1135 N) as per direction of Engineer-in-charge.

Providing and fixing of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N).

Providing and fixing of Tumbler Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat ACN 114 N).

Providing and fixing Bottle Trap (Jaquar Cat No. ALD. 769L) and other ancillary fittings. Cutting and making good the walls wherever required compete as per directions of Engineer-Incharge.

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. No. 70002) comprising of EWC –P, Cistern, Seat Cover, Twin Flush Fittings Wash Basin 450X300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer-in-charge.

Providing and fixing C.P brass single towel rail (600mm long) of approved make complete with C.P brackets fixed to wooden cleats with C.P brass screws (Jaquar Cat No. ACN 11011NM).

Providing and fixing brass towel Ring Round with Round Flenge of approved make complete with all fittings (Jaquar Cat No. ACN 11021 BN).

Providing and fixing of glass shelf 600m long with all C.P fittings of approved quality complete item (Jaquar Cat No. ACN 11071 N).

Providing and fixing toilet paper holder with all fittings Jaquar Contienal ACN 1153 N.

Providing and fixing 15mm dia C.P brass bib cock with wall flange of approved quality conforming to IS standard (Jaquar Cat No. 29037).

Providing and fixing 15mm dia C.P brass long nose bib cock of approved quality conforming to IS : standards and weighing not less than 810 grams (Jaquar Cat No. CON-107 KN).

Providing and fixing of regular body of concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar ALD-083) with exposed part angular stop cock with flange FUS 29.53.

Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves and brass tank Nipples etc. Including testing of lines and joints as per Engineer in charge. Make Kitec, Maithilee and Vista.

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

Conceal Inside the walls:- Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves etc. Make Kitec, Maithilee and Vista. Concealed, installation including cutting chases and making good in the wall etc, Complete in all respect. 1620 (20mm OD) pipe.

Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer's name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Connectors, with PAP valves etc. Trenching, re filling and testing etc. Complete as per Engineer In Charge. Make Kitec, Maithilee and Vista.

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed.

Providing at site of works and lowering, laying and jointing HDPE pipes and required specials of outer diameters conforming to IS : 14333-1996 and bearing ISI mark in prepared trenches to required grade and level icluding cost of jointing materials, chemicals, labour required for handling and making joints etc. including hydraulic testing of pipes, refilling of trenches etc. complete note :- Water for initial testing will be made available free by MIDC if possible. For subsequent fills necessitated on account of rectifications water will be charged at the prevailing industrial water rates in respective industrial area.

110 mm dia 6 Kg/cm2

160 mm dia 6 Kg/cm2

200 mm dia 6 Kg/cm2

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate) (including all leads and lifts carriages of material by MT/HL)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) (including all leads and lifts carriages of material by MT/HL)

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked)

Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity 15 No.).

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

Supply, assembly, erection, testing and commissioning of pumping system comprising the following: Vertical/Horizontal centrifugal pumps (1 Working + 1 Stand-by) with mechanical seal, SS Volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50 cycles A.C. supply with 100 mm dia. pressure gauges including MS skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump). Pump Capacity 180 lpm, at 30 m head (1 working + 1 standby) (Domestic water relift pump).

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor singlecore cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthingthe point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group B

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4.0sq. mm + 1 X 4.0sq. mm earth wire

2 X 6.0 sq. mm + 1 X 6.0 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 16.0 sq. mm + 2 X 6.0 sq. mm earth wire

TV Cable in existing conduit :- Supplying and drawing co-axial TV cable RG-6 grade, 0.7mm solid copper conductor PE Insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/PVC conduit as required.

S/F PVC Conduit:- Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of Recessed conduit as required

S/F modular boxes, base and cover plate :- Supplying and fixing following size/modules , GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 module ( 75mm x 75mm)

3 module ( 75mm x 75mm)

4 module ( 125mm x 75mm)

6 module ( 200mm x 75mm)

S/F power plug point modular type accessories:- Supplying and fixing on exisitng GI Box modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required.

Supply, Installation, Testing and commissioning of Modular Type Power Outlet Unit for AC / Geyser 572154 of Legrand or equiv in MK( Aspect) /Schneider Zencilo including supply and fixing GI box for mounting of Power Unit.

S/F Modular type switch/socket : Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6Amp Switch

2 way 5/6 Amp 2 way Switch

3 pin 5/6 Amp socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F modular type electronic fan regulator: Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F modular type blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F ceiling rose :- Supplying and fixing 3pin 5 Amp ceiling rose on the existing junction box/wooden block including connection etc. as required.

S/F call bell/ Buzzer:- Supplying and fixing call bell / buzzer suitable for D.C./A.C. single phase , 230volts, complete as required.

ITC fluorescent fitting directly on surface : Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

ITC Ceiling Fan : Installation, Testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto 30 cm) with 1.5sq mm FR PVC insulated, copper conductor , single core cable etc. as required including providing and fixing phenolic laminated sheet cover on fan box etc. as required

Numbering of Fan/Fittings :- Numbering of ceiling fan/exhaust fan / fluorescent fittings as required.

ITC exhaust fan upto 450mm sweep:- Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Fixing louvers/shutters for exhaust fan:- Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Telephone wiring in existing conduit:- Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required

S/F Prewired TP MCB DB:- Supplying and fixing following way , sheet steel, IP 43 MCB distribution board, 415/230 volts, on surface/recess, complete with , terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc. as required.( But without MCB/RCCB/Isolator)

2 Rows X13 modules, Double door

3 Rows X13 modules, Double door

4 Rows X13 modules, Double door

S/F 'C' series , SP MCB:- Supplying and fixing 5 amps to 32 amps rating, 240 Volts, 'C" series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

S/F 'B' Series, SP MCB blanking plate Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, MCB, 10kA, Class 3 with integral label holder in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply, Installation, Testing and commissioning of automation system consisting of the following componenents ( Makes : Dynalite/Legrand/Lutron):

DDMC 802 controller consisting of 6 Nos 2A Channels of Leading Edge Dimmers, 2 Nos Relay Control Modules

8 button Programmable Keypad suitable for integration with above controller

Polycarbonate Enclosure for mounting the Controllers , Terminal Blocks, 2 Nos 22A 2p contactors, including internal wiring, connections of components

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

P/F M.V. danger notice plate : Providing and fixing M.V. danger notice plate of 200mm x 150mm , made of mild steel, at least 2 mm thick , and viterous enamelled white on both sides, and with inscription in single red colour on front side as required.

S/L 8 SWG copper wire in ground:- Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required.a) 150mm dia R.C.C. Pipe (including all leads and lifts carriages of material by MT/HL)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

upto 35sq.mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

upto 35sq.mm

Above 185 sq. mm and upto 400 sq. mm

Supply of 1.1kV Grade XLPE Insulated PVC sheathed Aluminium Armoured cables conforming to IS 7098 Part-II of following ratings conforming to IS 7098 Part-1 with Latest Amendments

3.5C X 400 sq. mm

3.5C X240 sq. mm

4Cx 16sqmm

S/M LV/MV cable end termination: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required

3½ X 400 sq. mm (82mm)

3½ X 240 sq. mm (62mm)

Supplying and fixing following modular Bell Push on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supply of following LED lighting fixtures : 19W( Maximum) 4ft LED Surface Mounted light fixture 2000 lumens having minimum system lumen efficiency of 100 Lumens per watt equivalent to Endura LED BN108C 6500K, L70 40000hrs of Philips /Trilux/GE

38W( Maximum) 4ft LED Surface Mounted light fixture 4000 lumens having minimum system lumen efficiency of 100 Lumens per watt equivalent to Endura LED BN108C 6500K, L70 40000hrs of Philips /Trilux/GE

12W ,1100 Lumens ( system output), surface mounting having CRCA body, IEC compliant driver LED Fixture SM200 Cirrus Mini Pro of Philips/Trilux/GE

15W ,900 Lumens ( system output), surface mounting having dies cast aluminium housing and heat sink, IEC compliant driver LED Fixture SM518C Cirrus Mini of Philips

10W LED Endura Bulkhead IP66 WT202W of Philips/Trilux/GE

30W ( Maximum) 2ftx2ft Dimmable LED Recess mounting Light Fixture 3000 Lumens having minimum system lumen efficiency of 100Lumens/watt equivalent to RC380B LED 30S 6500 PSD OD of Philips

Supply of 1400mm sweep 230V 50Hz celing fan with double ball bearing with low power consumption

Supply of following sizes of heavy duty exhaust fan as per approved makes

300mm Sweep:- Supply, Installation, Testing and Commissioning of 225mm(w)x38mm(h) 3 compartment GI underfloor raceway of Legrand/OBO/Hager makes.

Supply, Installation, Testing and Commissioning of Galvanised Steel Junction Box of size 225mmX225mm suitable for 225mm(w)x38mm(h) 3 compartment GI underfloor raceway of Legrand/OBO/Hager makes.

Supply Installation Testing and commisionng of Local Arrea Network system consiting of following components

Supply , Installation of 15U Network Rack made of CRCA 1.2mm sheet powder coated with RAL9017 color, 4mm toughened tinted glass, Injected one piece polyurethane gasket on frame. Rack components shall be Cooling Fans - 2 Nos, cable Manager - 3Nos, cantilever tray 255D-1 No., Heavy duty stationery shelf, hardware, nuts , power distribution boards - 5 Nos Makes : Systimax/Avaya/Legrand

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

Makes of Cat 6 cable : AT&T/Legrand/HP Supply erection, 24 Port Patch Panel Cat6 Makes : Systimax/Avaya/Legrand

Supply erection, Testing and commisioning of Cat6 UTP keystone connector

Supply erection, Testing and commisioning of Cat6 UTP patch cord 1m Makes : Systimax/Avaya/Legrand

Supply Installation Testing and commisionng of RJ45 outlet in existing boxes / plates / frames Makes : Systimax/Avaya/Legrand

Wifi Access Point with PoE Supply, Installation, Testing and commissioning of 150KVA Indoor type, Unbalanced input , unbalanced output, LV Automatic Servo Voltage Stabilizer indoor type, suitable for input voltage range of 135V to 460V three phase, and out voltage at 433V +/-1%. The stabilizer shall have all necessary protections i.e. overvoltage , undervoltage, surge protection, overcurrent, short circuit. Contractor shall submit necessary documents, drawings for approval before intiating procurement process. Stabilizer shall have suitable arrangement for termination of cables as per site requirements. Stabilizer shall be supplied with first fill of oil, suitable rating MCCB at the output side. Makes :Andrew Yule/ Brentford/ Automatic Electric/Jaima

Supply , Installation, Testing and commissioning of POP up box suitable for 6Module accessories mounting euivalent to 0540 17 of Legrand / Schneider/MK( Aspect)

Supply, Installation of DLP PVC Trunking system on walls consisting of following components ( Legrand/Hager/MK)

DLP Trunking Body 50mmx145mm with 2 covers 45mm

End cap for Item 33 (a)

Flat Angle for Item 33 (a)

External Angle for Item 33 (a)

Internal Angle for Item 33 (a)

Flat Junction for Item 33 (a)

4M frame for mounting of Outlets/Swiches

6M frame for mounting of Outlets/Swiches

Supply, Installation Testing and commisisoning of 10kVA min VAH10080 rating Online Double conversion IGBT True Online Uninterrupted Power Supply alongwith 30 Minutes battery backup suitable for three phase 330-415V input and three phase 415V +/-1% output. UPS shall have inbuilt galvanic isolation transformer , automatic and manual byepass system. UPS shall be supplied with SMF batteries, Mounting rack for batteries, internal cabling/busbar for banking of batteries, cabling between UPS to Battery bank. UPS shall have inbuilt protections against short circuit, undervoltage, overvoltage, surge protection, loss of neutral. Makes :Mitsubishi/Numeric/APC/Emerson

Supply, Installation of 10 pair Telephone krone box suitable for Termination of 10 Pair Telephone cable including Krone connectors for 10 Pair cables. Hensel make

Supply, Installation Testing and commissioning of IP CCTV system suitable for integration with Networks Makes Samsung/Bosch/LG/Hikvision consisting of the following components, contractor to quote considering all components that may be required to complete the jsystem as per owner satisfaction, no extra cost shall be paid for any item requred to complete this job.

Full HD 2 MP ((1920x1080) Resolution with IR Range 10-30 mtrs approx., POE, 1/2.8'' Progressive Scan CMOS Indoor Dome IR Network Indoor Camera equivalent to DS-2120F-I(W) of Hikvision

HD 2 MP(1920x1080) Resolution with IR Range 20-30- mtrs approx.,POE, IP 67,1/2.8'' Progressive scan CMOS Outdoor Vandal Proof Bullet IR Network Camera equivalent to DS-2CD2020F-I(W) of Hikvision

Outdoor Network PTZ Camera wirh 1920x1080 resolution, support H.265 video compression Dome Type , DWDR, upto 100m IR Distance, 20X optical zoom, 16X digital zoom, Pan and Tilt , IP66 with inbuilt surge, lightening and transient voltage protections equivalent to DS-2DE4220IW-D of Hikvision

Network Video Recorder 8 channel of IP , delivering 1920x1080 (1080P), 2HD video resolution, H.264. Real time video recording at 4CIF resolution.

4TB Hard disk

24- Ports Layer 2 PoE Switch : 24-Port 10/100/1000 Base-T Gigabit PoE (8-Port PoE+) Smart Managed Switch with 4 Gigabit Dedicated SFP Slots and Static Routing Support

Surge Protector for IP Camera

32" high resolution LED Display with HDMI interface application with all accessories of wall mount

Supply, Installation, Testing and commissioning of Floor Mounted Low Voltage servo stabilizer bypass panel IP42 suitable for operation on 433V 3 Phase, 50Hz supply, made of 2.0mm CRCA sheet enclosure with Aluminium bus bar Four wire with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoing cables . Contractor to get the G.A. drawings approved before execution. (Make of Panel Integrator : Jaima/Electricfield/ Simon /Nachiketa/ Acubb/Power Control System), 400A 4P MCCB 36kA - 1Nos. 250A 4P MCCB 36kA - 2Nos.Aluminium Bus Bars 4 Wire shall be 600Amps, MCCBs shall be interlocked as required by the scheme , all necessary accessories shall be provided in the panel by the contactors including Indications, Auxilliary contacts etc, Make of MCCB/MCB : Schneider(NSX), Siemens(3VL), Legrand( DPX3)

Supply, Installation, Testing and commissioning of Floor Mounted Low Voltage servo stabilizer bypass panel IP42 suitable for operation on 433V 3 Phase, 50Hz supply, made of 2.0mm CRCA sheet enclosure with Aluminium bus bar Four wire with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoing cables . Contractor to get the G.A. drawings approved before execution. (Make of Panel Integrator : Jaima/Electricfield/ Simon /Nachiketa/ Acubb/Power Control System), Incomer:, 250Amps 4 Pole MCCB 25kA- 1 no., 100Amps 4 Pole MCCB 25kA - 1No., Digital Energy Meter for Measurement and display(LED/LCD) of Current, Voltage, Pf, Active , Reactive power, kWh, kVArH, kvAh, Harmonics, Current Transformer set having Ratio of 160/5, set of protection MCBs, Bus Bar : , Bus Bar : 600A 4 Wire Aluminium Bus Bar supported on DMC insulator, covered with high quality PVC sleeves, 100Amps 4 Pole On load Changeover - 1No.Outgoing : 100A 4P MCCB 16KA - 6 Nos 63A 4P MCCB 16kA - 6 Nos 40A 4P MCCB 16kA - 6 Nos All MCCBs shall be provided with Rotary operating Mechanism. All incomers and outgoings shall have on off indication. Incomers shall have Phase Indication LED. All MCCBs shall have Ics=Icu=100% Makes of MCCBs : Schneider(NSX)/Siemens(3VL)/Legrand(DPX3) Makes of Changeover : Socomec/Hager/L&T

Supply Installation of 7 m long galvanised octagonal pole with bracket for mounting of 1 Nos LED street light including making foundation for the pole complete job, wiring from pole junction box to light, junction box with terminal blocks suitable to terminate loop in loop out cable of 4Cx16sqmm Aluminium along installation of with 6A SP MCB - 1No. in the box. Pole and foundation drawings to be got approved from Deptt before supply. Make of Poles : Philips/GE/Thorn

Supply, Installation, Testing and commissioning of 36W led Street lights having system lumen efficacy of minimmum 100 lumen per watt, 3 kv Surge protection, IP 66, manufacturere name Embossed on dicast Aluminium body .Make of flood light GE,Phillips,Trilux ,Thorn,Zumtobel.

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete.

Stone aggregate below 40mm size for an average lead of 32 Kms average from Chadwal.

Sand for an average lead of 30 Kms from Tarnah .

Bricks for an average lead of 45 Kms from Hiranagar .

Brick bats (size 25mm to 115mm) for an average lead of 45 Kms from Hieanagar.

Harish Kohli