SPECIAL REPAIR TO BLDG NO P-94, P-97 AND P-147 AT SHEKHAWATI LINE UNDER GE (WEST) DELHI CANTT-10

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not other specifically provided for complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and as in columns, beams, slabs, parapet wall, drops, chajjas and shelves etc not other specifically provided for complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed.

Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces and removing the debris upto the distance exc 1.00 Km but not n.exc 1. 5 Km complete all as specified and directed.

Dismantling of PVC water storage tanks exc 250 & n.exc 500 ltrs capacity and removing from site complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 100mm complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal dia of pipe 75mm complete all as specified and directed

Taking down cement or cement lime plaster on walls incl racking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed

Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter from frame) exc 1.5 Sqm and n.exc 4 Sqm each and removing to or from store complete all as specified and directed.

Taking down wooden/steel chowkhats/door frame including shutter (without taking off shutter) not exc.1.5 Sqm each and removing to or from store complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm and not exc 2.00 Sqm complete all as specified and directed.

Taking down shutter of any description not exc 1.00 Sqm complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding , removing serviceable tiles to store and rubbish off the premises all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floor or in any position laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of brick work built in cement /lime mortor in any position / situation in walls/parapets complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections incl cleaning for refixing or removal to store complete all as specified and directed

All as per item No. 16 here-in-before but 20mm bore.

All as per item No. 16 here-in-before but 25mm bore.

All as per item No. 16 here-in-before but 40mm bore.

Scraping old tar felt roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface complete all as specified and directed

M&L for providing Cement concrete 1:5:10 in filling of sunken portion type E2 using 40mm graded aggregate complete all as specified and directed

M&L for providing cement concrete 1:2:4 type B-I 20mm graded in roof kerb or mud slops, rounded or chamfered on edges, plinth courses, coping, kneelers, apex stone, kerb water tough and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work and finished surfaces complete all as specified and directed

M&L for water proofing treatment to roof surface with APP polymeric based water proofing membrane 3mm thick & weighing not less than 3.5 Kg / Sqm of approved make black finish consisting of a central core of high molecular high density polyethylene film (HMHDPF) & reinforced with non woven polyester matt of min 160 gm/sqm with a thermo fusible finish laid over a coat of hot blown bitumen of 85/25 grade conforming to IS 702 @ 1.2 kg/sqm over a coat of an bitumen primer conforming to IS-3384 @0.4 Ltr/Sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing including applying a coat of cold emulsion bituminous primer complete as per manufacturer's instructions complete all as specified and directed. (Make Super thermolay manufactured by STP Ltd or 'Hyper Plas' (Polyster) manufactured by M/S IWL Ltd or 'Shalipals' (polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd) Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen primer, bitumen and membrane shall be of same make / manufacturer. (ii) The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65mm X 50mm size& making good in CM 1:3.

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) on roof padding with water proofing compound as per manufacturer's instruction surface finished even and smooth without using extra cement complete all as specified and directed. (Note :- Rate of WPC shall be included in unit rate)

M&L for 20cm x 20cm x20mm thick PCC tiles bedded in cement mortar (1:3) 15mm thick and jointed and grouted flush in CM 1:3 mixed with 5% crude oil by weight of cement complete all as specified and directed

M&L providing pre cast reinforcement cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in Kitchen slab, passage roof etc and set in cement mortar 1:4 complete all as specified & directed.

M&L for TMT bars 6 to 8mm dia cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

M&L for brick work with class 'A' brick straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6 complete all as specified and directed

All as per item No. 28 here-in-before but half brick thick in CM 1:4.

S&F for tubes, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors GI complete all as specified and directed

All as per item No. 30 here-in-before but 20mm bore tubing.

All as per item No. 30 here-in-before but 25mm bore tubing.

All as per item No. 30 here-in-before but 40mm bore tubing.

M&L for cutting chases for inserting GI tubing in walls, floor etc and making good complete all as specified & directed.

S&F rotational moulded polythylene water storage tanks 1000 Ltrs capacity, double layered (cylindrical vertical with closed up) hoisted and fixed in position complete all as specified and directed.

S&F 100mm bore cast iron soil waste or vent pipes in any length with or without ears with lead joints laid in trenches or in floors/ walls all as specified and directed.

All as per item No. 36 here-in-before but 75mm bore of pipe.

S&F 100 mm bore cst iron 'P' or 'S' traps fixed with lead joints all as specified and direced.

S&F 100mm bore cast iron bends (any radius) diminishing pieces or tapers (larger bore to be measured) with oval access doors complete all as specified and directed

All as per item No.39 here-in-before but 75mm bore of pipe.

S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including oval access door complete all as specified and directed

All as per item No. 41 here-in-before but 75mm bore of pipe.

S&F CI Cowl for 100mm bore of CI pipe complete all as specified and directed

S&F in repairs 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket complete all as specified.

S&F in repair vitreous china water closet Orissa type 580 x 440 mm white with integral foot rests including provn of lime concrete bedding including connections to flushing cistern pipe and making good disturbed portion to match existing surfaces including 'P' or 'S' trap of CI complete all as directed

S&F in repairs vitreous china wash hand basin (flat black) white of size 550x400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified.

S&F in repairs CI floor trap with grating including jointing to waste pipe in run lead with dia of outlet 75 mm including floor around to required depth and burning lead joints etc to facilitate dismantling old CI trap and making good complete all as directed.

S&F in repair PVC (SWR) bends 150 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) 150 mm bore rain water pipes single socketed in any length with rubber ring joints fixed to walls / spout pipe complete all as specified and directed.

S&F mild steel framed work as in door or gates of angle or other sections, cooler stands, with gusset plates rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel sheeting or other covering, running rails and guides) and hanging, fastening and fixing conforming to Fe 290 Gde E-165 complete all as specified and directed

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels commercial type covered with decorative face veneer with lipping/ frame to match all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed.

M&L for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm fixed to door/window frame complete all as specified and directed.

All as per item No. 53 here-in-before but fixed in repair.

S&F butt hinges 100mm size, medium weight cold rolled mild steel and fixed to angle iron /steel chowkhat complete all as specified and directed.

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed

S&F aluminium anodised barrel tower bolt, extruded section 200mm size complete all as specified and directed

S&F aluminium anodised Handles for 150mm size complete all as specified and directed

S&F aluminium anodised Handles for 100mm size complete all as specified and directed

S&F 300mm aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 4.8 mm thick figured glass/ pin head type and glazing in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality and glazing in square not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 100 mm hasp and staple, aluminium anodised including bolt to hinges plate and fixed with screws complete all as specified and directed

M&L for Preparation of new or previously untreated surfaces of wood or wooden base surface of any description not otherwise described over 10cm width or grith and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

All as per item No. 64 here-in-before but on steel surfaces over a coat of redoxide primer.

M&L for Preparation of old wooden surfaces of any description not otherwise described over 10cm width or grith and applying one coat of synthetic enamel paint complete all as specified.

All as per item No. 66 here-in-before but one coat of paint on old steel surfaces.

M&L ready mix plaster 15mm thick on internal wall/ concrete surface and finished even and smooth complete all as specified.

M&L ready mix plaster 12mm thick on external wall/ concrete surface and finished even and smooth complete all as specified.

M&L ready mix plaster 5mm thick on ceiling plaster and finished even and smooth complete all as specified.

M&L for 5mm thick rendering in cement mortar (1:3) on ceiling surfaces of any description, finished even and smooth complete all as specified and directed

Complete removal and preperation of old surfaces of walls by scrapping with mechanical grinders complete complete all as specified and directed

M&L for two coats of oil bound distemper including preparation of new plastered surfaces over one coat of alkali resistant primer & including 2mm thick wall care putty complete all as specified.

M&L for two coats of oil bound distemper on old surfaces of walls by complete removal of old treatment & preparation of old surfaces over one coat of alkali resistant primer & including 1mm thick wall care putty complete all as specified.

M&L three coat of white washing on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed

M&L two coats of white washing on old plastered surfaces of walls including preparation of surfaces complete all as specified and directed

M&L three coat of white washing on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed

M&L two coats of white washing on old ceiling surfaces including preparation of surfaces complete all as specified and directed

M&L for preparation of old treated brick surfaces of walls upto 4th storey height by scrubbing with wire brush, hard brush, washing down with water and applying two coats of cement paint, white or tinted over one coat of alkali resistant primer complete all as specified and directed

M&L for preparing new plastered surfaces of wall upto 4th storey height and applying two coats of cement paint, white or tinted over one coat of alkali resistant primer complete all as specified and directed

M&L for Chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting scrubbing down concrete surface with wire brushes, cleaning with water, allowed to dry and applying a layer of antirust and then Zinc rich epoxy primer all as specified followed by a layer of cementious bonding & then guniting over steel welded mesh 2mm dia of wire and aperture 75mm total thickness of guniting not exc 25mm thick (average thickness) with cement mortar 1:2 using OPC 43 grade cement and finally applying cement plaster over guniting surface of required thickness to give even, uniform, and smooth finish conforming to proper geometrics in cement mortar 1:3 to match with the existing surface as in sides and soffits etc. slabs, Chajjas, fins, facias, parapets, beams and columns etc complete including necessary scaffolding, shuttering, necessary chases to brickwork or RCC members at any height up to 4 storey building complete all as directed. Note: Steel Welded mesh is to be welded with existing reinforcement. The Cost of welded mesh is deemed to be included in the unit rate quoted and the work to be carried out up to 4 storey bldgs/in floor roofs.

All as per item No. 81 here-in-before but exc 25mm thickness but n.exc 40mm thickness.

M&L for 18-20mm thick, granite (of any type) work (rounded edges of exposed edges and polishing) in window-cills, cooking platforms and like in 15mm tihck cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

M&L for non skid colour ceramic rectified tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.06Sqm but not exceeding 0.11Sqm, in floors etc, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for coloured printed glazed ceramic tiles of size 450X 300X 7mm on vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 10mm thick in cement mortar 1:4, complete all as specified.

M&L for non skid colour ceramic rectified tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick laid in bays and surfaces finished even and fair, including filling the joints with bitumen mastic complete all as specified and directed.

S&F in repair chromium plated tubular towel rail 20mm dia, D type 60 cm long between flanges, complete all as specified and directed.

S&F curtian rod of 25mm MS pipe wiht PVc coating with fixing brackets and decorative finials all as specified and directed.

S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever, brackets and connecting union to pipe over all size 495 x 420 mm, bowl size 410 mm x 330 mm x 160mm complete all as specified and directed.

S&F in repairs 15mm dia bib tap fancy type brass with capstan head chromium plated screwed down high pressure with long screwed shank and flynut screwed completeall as specified. Make :- Jaquar cat No CON107KN, Prayag cat No 7608, Cera cat No F1017152

S&F in repairs 15mm dia chromium plated bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.Make :- Jaquar cat No CON037KN, Prayag cat No 7606, Cera cat No F1017151

S&F brass CP vertical mixer for mixing hot & cold water for wash hand basin screwed down for 15 mm bore iron pipe of ferrule complete all as specified and directed.Make :- Jaquar cat No CQT23167B, Prayag cat No 7450, Cera cat No F2008461

S&F CP wall mixer non telephonic type for mixing hot and cold water for shower screwed down for 15 mm brass iron pipe of ferrule of complete all as specified.Make :- Jaquar cat No FLR 5273UPR, Prayag cat No 7365, Cera cat No F1017401

S&F in repairs 15mm bore stop valves/angle valves, cast copper alloys, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spd and directed. Make :- Jaquar cat No OPP-15053PM, Prayag cat No 7810, Cera cat No F1017201

S&F in repairs 25mm bore of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F PVC connection 600mm long with 2 Nos brass check nuts, suitable for 15mm bore complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminum rod and high density polythene float and flynut complete, screwed for iron pipe or brass furrule size 25mm bore. (Min weight 210gms) complete all as specified and directed

S&F in repairs shower rose, chromium plated brass, fancy type, 125 mm with or without swivel joint, any size, including fixing to steel pipe or union, complete all as directed.

S&F 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as shutter of cupboard complete all as specified and directed.

M&L for machine cut Kota stone slab 20 to 25 mm thick as in treads, risers of staicase laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including cement screed bed 15mm thick in CM 1:6 complete all as specified and directed.

S&F stainless steel kitchen plate rack made out of stainless steel sheets 1mm thick overall size 600mm x 750mm x 250mm including complete all as specificed and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S.square tube, suppling & fixing in opening as per specification & drawingcomplete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded pre-laminated PVC sheet having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined suitable PVC sheet beading and joined together with solvent cement and provision of partially louvered frame supply and fixing in the frame at site complete all as per specification & sample kept in GE office and as directed.

M&L in repairs for 18mm thick wood polymer composite board, prelaminated both sideswith decorative choice lamination fixed with screws to timber frame work as in kitchen cabinet as per sample kept in the office of GE complete all as specified.

M&L for teak wood lipping, 6mm thick fixed with nails to 18mm thick veneered particle borad including polishing complete all as specified.

S&F continous (piano) hinges, mild steel, bright finish complete all as specified.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of of brass polished bright finished complete all as specified.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified.

M&L for providing 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate admixed with integral WPC complete all as specified. (Note: Supply only WPC shall be measured and paid saparately.)

M&L for 10 mm thick cement plaster on brick/ concrete surface in CM 1:3, finished even and smooth surface with out using extra cement but with& using water proofing compound at the rate of 2% of cement by weight complete all as specified and directed (Note: Supply only WPC shall be measured and paid saparately.)

M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound complete all as specified. (Note : Supply only WPC shall be measured and paid separately)

M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall complete all as specified and directed

M&L for glass fibre reinforced acrylic modified cementious coating system with base coat of Sika Top @ Seal 107 or equivalent @ 1.50 Kg/Sqm fibre reinforcement Sika ® Fab-1 and top coat with Sika Top® Seal-107@ 1.50 Kg/Sqm or equivalent of FOSROC or PIDILITE complete all as specified and directed

S&F framed work such as grills, grating etc. with ends of bars shouldered and /or riveted , or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar works conforming to Fe290. Gde-E-165 complete all as specified and directed Note : Provision of openable arrangement for placing coolers on stand shall be made in window grill wherever required.

Supply only Integral waterproofing compound complete all as specified and directed

S&F powder coated aluminium frame for doors, windows, beading for grill with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thickness of powder coating 50 micron ).

S&F powder coated aluminium window, ventilator and sliding tracks shutters, side hung type with/ without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2 Nos) suitable handle (1 No) and 75mm long tower bolt (02Nos) complete all as specified and directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified & directed.

S&F aluminium anodised barrel tower bolt, extruded section 100mm size complete all as specified and directed

Taking down wooden door shutter exc 1.00 Sqm and n. exc 2.00 Sqm each and refixing in same opening complete all as specified and directed

S&F powder coated (minium thickness of powder coating 50 micron) aluminium section for shutters suitable for three/four track window and aluminium section weighting more than 0.45 kg/m of sliding members incl all necessary fittings and fixtures, jointing cleats, rubber packing etc complete all as specified and directed.

Supply only CP waste coupling 32mm size with PVC waste pipe, plugs and washers for kitchen sink complete all as spd & directed.

S&F MS powder coated peg set of size 175mm to 250mm complete all as specified and directed

All as per item 125 here-in-before but of size 125mm to 175mm

S&F of floor door stopper of alumimium alloy body and tongue, anodised, with hard drawn steel spring including vulcanised rubber piece of 140mm long complete all as specified and directed

M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes from all exposed / damaged portion of coloumns, slabs & beams (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine or suitable brushes & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm (average thickness). Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed.

(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly.

Supply & fixing 8-10mm dia steel sheer connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA). (The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item) complete all as specified and directed.

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine or suitable brushes & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm - 384 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm - 336 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

S&F for stengthening existing reinforcement by use of mild steel TMT bars of any dia, cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over 25mm thick sand cushion with grey cement and pigment complete all as specified and directed. (Note : Sand filling to be measured and paid seperately)

M&L for sand filling under floors for cushion bed to interlocking paver block complete all as specified and directed

M&L for TMT bars 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

All as per item No. 142 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders all as specified and directed.

M&L for RCC M-25 design mix cement concrete (20mm graded aggregate) as in lintel, cooking platform etc in floors, roofs, landings, balconies, canopies deck slabs and in shelves and the like all as specified and directed.

S&F FRP chajjas of 450mm wide shitable for various openings including fittings and fixtures upto 4 storey bldg complete all as specified and directed.

M&L for formwork soffits of suspended slabs such as kitchen shelves, lintel & similar works not exceeding 200mm thick (Horizontal or slopping with rough finished surface of concrete all as specified and directed.

S &F factory made 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I). klin seasoned and chemically pressure treated complete all as specified and directed.

S&F of stainless steel soap dish of standard size complete all as specified and directed

Providing and laying in slabs, beams, parapet wall, RCC walls, columns etc position of RCC M-25 design mix grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying and the cost of centering, shuttering, form work, jack support upto forth storey bldg and excluding reinforement, including admixtures in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without imparing strength and durability as per directed of Engineer-in-Charge. The mix design as per particular specificatons shall be got approved by Engineer-in-Charge before execution of the item. The rate shall include cost of all specified materials and operations at all levels and heights, including the cost of centering, shuttering and form work excluding reinforcement which shall be paid under relevant items complete all as specified and directed. (Note :- Cement content considered in this item is @ 300 kg/cum as per IS 456 table showing minimum cement content. No extra will be paid nor any amount will recovered on account of variaton of cement in mix design as per specifications for controlled concrete.

M&L 10mm thick rendering in CM 1:4 mixed with water proofing compound when concrete is green, finished even and smooth complete all as specified and directed (Note :- WPC shall be measured and paid separately)

S&F brass CP sink mixer for mixing hot & cold water for screwed down for 15mm bore iron pipe of ferrule complete all as specified and directed. Make :- Jaquar cat No CQT23309, Prayag cat No 7655 , Cera cat No F1017501

S&F MS hand rails, half/full round on roof for parapet, balcony and staircase railing or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including bedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc) including all necessary drillling, bolting or riveting etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Providing and injecting chemical emulsion for post construction anit-termite treatment along external wall where the apron is not provided using chemical emulsion @ 7.5ltr/sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and directed

Treating of soil under existing floor using emulsion @ 1ltr/hole, 300mm apart including drilling and plugging 12mm dia. Holes wiht CM 1:2 (1 cement : 2coarse sand) to match the existing floor complete all as specified and directed

Description of Work / Item(s)

Amount

Taking down carefully point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fittings such as switches, light fittings,ceiling rose, pendent holders, bell, regulators and socket point etc and removing teh material from site including making good the disturbed surface to match with the existing surface complete all as specified and directed.

M&L for concealed point wiring with PVC insulated multi stranded unsheathed colour code copper conductor in PVC conduit with FRLS cable 1.5sqmm size, 1100 volts grade conforming to IS-: 694 in new GI boxes of 1.6 mm thick including one coat of synthetic enamel black paint and providing new 3mm thick plastic laminated sheet cover of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit complete all as specified for the following :- Note :- Cost of chiseling cutting of existing surface and making food to match with existing surface shall be deemed to be included in quoted rates.

(a) One light/fan/Exhaust fan/bell point controlled by one switch.

(b) All as per Srl item No 2 (a) here-in-before but one 5 Amps socket outlet point independent

(c) All as per Srl item No 2 (a) here-in-before but one 5 Amps socket outlet on same board.

(d) All as per Srl item No 2 (a) here-in-before but One light point controlled by two 2 way switch

M&L for concealed point wiring with PVC insulated multi stranded unsheathed FRLS copper conductor in PVC conduit with cable 2.5sqmm size, 1100 volts grade conforming to IS-: 694 in new GI boxes of 1.6 mm thick including one coat of synthetic enamel black paint and providing new 3mm thick plastic laminated sheet cover of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for one 3 pin socket 15 A independent board complete all as specified Note :- Cost of chiseling cutting of existing surface and making food to match with existing surface shall be deemed to be included in quoted rates.

S&F in repair switch piano flush type 5 amps single pole one way complete all as specified and directed.

S&F in repair switch piano flush type 15 amps single pole one way complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin 5 amps complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 5 and 15 Amps flush type complete all as specified and directed.

S&F in repair switch Piano flush type SP two way 5 Amps complete all as specified and directed.

S&F in repair bell push flush type 5 Amps complete all as specified and directed

S&F in repair bell ding dong type, 230 Volt, Single Pole all as specified and directed.

S & F in repair polycarbonate ceiling rose 3 pin flush type 6 A 250 V AC with ISI marked including ring for jumbo ceiling rose complete all as specified and directed

S&F in repair electronic fan regulator 0-4 steps step type 100W hum free including 6A socket frame and including connections complete all as specified and directed.

S&F in replacement of LED of 7 watt Lamp 6500Kcomplete all as specified and directed.

S & F in repair LED light fitting 1X10W bulk head luminaires including LEDlight driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make :- Havells cat No HEXAFT10WLED857SSYMBOPC, C&S No LTB10WLED, Polycab No PLT0101316

M & L in repair Decorative walll light fixture made up of Polycarbonate, Spiral B-22 Base suitable for 7 Watt LED Lamp including 7 watt lamp complete all as specified and directed. Make :- Havells cat No LHFOFUE1TZ1W012, Surya No SLE WL 6W-GP200

Supply and fixing in repair LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed. Make :- Havells cat No LUMILINEPLUSBS20WLED865SPCSS, C&S No LTTB4F20WLEDE1W, Polycab No LD00103044

S&F in repair single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC suitable for ‘B’ curve, conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F in repair Single pole MCB 40 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity, and terminal box suitable upto 35 sqmm cable conforming to IS 8828 of 1996 complete all as specified and directed.

S&F in repair SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity and terminal box suitable upto 63 sqmm cable conforming to IS 8828 of 1996 complete all as specified and directed.

S&F in repair factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in in repair of MCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal megnatic release complete all as specified directed.

S&F in repair factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

Taking down sub main wiring of sizes complete all as specified and directed.

S&F submain concealed wiring alongwith earth wire with 2 runs of 6 sqmm (main cable and neutral) and one run 6 sqmm as earth wire of multistanded unsheathed colour code FRLS PVC insulated copper conductor, single core cable drawn through and including rigid PVC conduit of size 25mm dia with all fittings and accessories complete all as specified and directed. Note :- Cost of chiseling cutting of existing surface and making food to match with existing surface shall be deemed to be included in quoted rates.

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burieddirectly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

S&F exhaust fan metallic type ventilating single phase 230/240V of 300 mm sweep with louvers including cutting of holes in a round shape and including fixing the ventilating fan complete all as specified and directed.Make :- Havells cat No VENTIL AIR DSP 300MM, Usha No AEROCLEAN 300MM, Bajaj No BAHAR 300MM

Taking down ceiling fan and deposit in MES yard complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.Make :- Havells cat No EFFICIENCIA NEO, Bajaj No Energy 32, Usha No Energia 32

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. Make :- Havells cat No ENDURACITYLITEPLATPLUSSL35WLED757SASYB0PC, C&S No LTESSE36WLED, Polycab No PUB0506027

S & F in replacement Lamp holder with insulated body with back plate suitable for batten fittings complete all as specified and directed

S&F of electric storage water heater of capacity 25 ltr BEE 5 star with vitreous enamel coating with all accessories and fittings arrangements and testing after installation complete all as specified and directed. Make :- Havells cat No GHWAPTTWH025, Bajaj No Calenta, Usha No Aqua Genie, Record No Eterno Pro

S & F of PVC fresh air exhaust fan 250mm single phase, 230/240 V with louver including cutting of holes in a round shape (Precast piece to be incorporated for smooth and ever finish) and including fixing the exhaust fan complete all as specified and directed Make :- Havells cat No Ventil Air DX 250mm, Bajaj No Maxima DX 250mm, Crompton No Brisk Air 250mm

S & F bib taps 15mm fency type with crutch or butterfly handle, screwed downscrewed for GI pipe complete all as specified and directed

S & F stop valve 15mm fency type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for GI pipe complete all as specified and directed

S & F GI tubing pipe galvanized, "medium class" supplied and laid including fittings 15mm dia complete all as specified and directed

Cutting of exising water supply main any size upto 25mm for taking branch connection of size 15mm including insertion of Tee unegual all as requied at site complete all as specified and directed

imran construction company

imran construction company

Bidder Name

imran construction company

A R construction