DAY TO DAY/PETTY REP TO MISC BR ITEMS AT OTM AND MD ACCN AT NAVAL STATION THANE AND REPAIRS AND CLEANING TO SEWAGE LINE, MANHOLE, SEPTIC TANKS AND REPAIRS TO PATH, GATES AND CERTAIN B/R WORKS AT NAVAL STATION THANE UNDER GE (NW) MANKHURD

Amount

Petty repairs to wooden joinery works such as Resecuring or easing and adjusting of doors, windows kitchen cabinets in any size, refixing hinges etc by providing glue nails and screws to the satisfaction of user and rectifying other misc minor carpentary works assigned by the Engineer In charge. (Note : Replacement of builders hardware if required shall be measured and paid separately as supply only.) Note item No 1 and 2 : (a) Rep of contractor will collect details of complaint from departmant. The contractor will be alloted complaint on daily basis and sufficient resources will be deployed by him/her for completion of day to day complaint within 24 Hrs from the time of reporting. Any delay beyond above mentioned time limit suitable penalties @ Rs 860/- per head per day shall be made proportionally from contractor' due. (b) A detailed log of complaints with completion/ non-completion remarks from users/MES will be maintained by the contractor and same will be updated on daily basis in consulatation with Engr-in-Charge or JE detailed by him. (c) The contractor will make suitable arrangment for emergent complaints and will notify auth rep/Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond state time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard. (d) The quoted rate deems to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Naval Station Thane. (e) The contractor will maintain suitable inventories and range of spares required to meet the complaints as same will be reviewed periodically by Engr-in-charge to streamline complaints disposal system.

Petty repairs to plumbing/internal water supply works such as repair to leaking bib taps, pillar taps, mixers stop cocks by tightening and providing spindle,washer repairs to float valves, low leveled flushing cistern to the satisfaction of user as assigned by the Engineer In Charge.

Taking down cement plaster on brick or concrete or stone surfaces etc, including raking out joints, hacking for key, scrubbing own with water, etc complete all as specified and directed.

M & L for rendering 15 mm thick in CM 1:6 on brick walls or concrete surfaces finished the surfaces even & smooth incl 1mm thick sagol finish layer including preparation of old surfaces in patches for repairs at any places inside the bldg complete all as specified and directed.

M & L for rendering 20 mm thick in CM 1:4 on brick walls or concrete surfaces laid in two layers, Ist layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @ 2% by weight of cement content of finishing layer finished fair and even without using extra cement,additonal thickness provided as floating/setting coat, including all necessary scaffolding/staging as required including preparation of old surfaces in patches for repairs at any places outside the bldg complete all as specified and directed.

M & L for rendering 05 mm thick in CM 1:3 on ceiling , soffit of staricase surfaces finished even and smooth with 1mm thick sagol finish layer, including preparation of old surfaces in patches for repairs at any places inside the bldg complete all as specified and directed.

M & L preparing new surfaces of walls applying two coat of oil bound distemper over one coat of primer complete all as specified & directed

M&L preparation of new plastered surfaces on wall including necessary scafolding and applying two coats of 100% anti fungal acrylic exterior emulsion paint over a coat of acrylic primer complete all as specified and directed.

M& L for preparation of newly plastered surface and applying three coat of white wash on ceilings complete all as specified and directed

Suply only stainless steel butt hinges, 100mm, medium weight complete all as specified and directed

Supply only stainless steel butt hinges, 75mm, medium weight complete all as specified and directed

Supply only aluminium, anodised, barrel tower bolts of extruded section of size 200mm complete all as specified and directed.

Supply only aluminium, anodised, barrel tower bolts of extruded section of size 100mm complete all as specified and directed.

Supply only extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed.

Supply only floor door stopper aluminium body over length of cover plate 140 mm and tonque anodised with hard drawn steel spring complete all as specified and directed

Supply only aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 300mm fixed at any position all as specified and directed.

Supply only heavy duty magnet suitable for cupboard and similar itmes etc complete all as specified and directed.

Supply only Cast iron body door closer for aluminium door shutter hydraulically regulated,designation No 1 universal type,suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixed complete all as specified and directed

Taking down aluminum door shutter carefully and refixing the same in position replacing rubber bead, worn-out door closer mortice lock and replacing existing broken aluminium section / glass / wire cloth / Bakelite sheet, if any and making door shutter serviceable, for work complete all as specified and directed. Note - Aluminum Section / Glass / wire cloth / Bakelite sheet, shall be measured and paid separately as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

Taking down aluminum window shutter carefully and refixing the same in position replacing rubber bead, worn-out handles and replacing existing broken Aluminum section / glass/wire cloth/backlite sheet, if any, and making window shutter serviceable, complete all as specified and directed. Note - Aluminum section / Glass / wire cloth / Bakelite sheet, handle etc shall be measured and paid separately as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Taking down chowkat or frame with shutter (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames), exc 1.50 sqm but not exc 4.0 sqm each complete as directed

Taking down shutters of any description, not exc 1 Sqm each complete all as specified and directed

Taking down shutters of any description, exc 1 Sqm and n.exc 2 sqm each complete all as specified and directed

M&L for IInd class Hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joint complete all as specified and directed.

S & F,IInd class hardwood 35mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S & F 2nd class hardwood, glazed and skelton shutter, 35mm thick, open rebated and prepared to receive glass, gauze etc, divided into square with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plane, chamfered or rounded, fitted with cut and mitered bead for securing glass, gauze etc, size of member of shutters as specified in SSR Part -I, section 8, class 8.24(a) (Door shutter), supplied and fitted to chowkats all as specified and directed.

S & F in repairs 2nd class Hard wood plain fillets squares, rectangular or triangular in section, wrought, secured with screws, sectional area exc 13 Sqcm and not exc 25 Sqcm complete all as specified and directed.

M&L for 18/19mm thick pre laminated particle board interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to timber frame work, complete all as specified and directed. Or any other position as directed.

S&F for Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

M&L for factory made solid PVC panel type PVC door shutter 30 mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, paneling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site complete all as specified and directed.

M & L for 20 to 25mm machine cut, polished kota stone slab, in single piece, in window cill, riser of steps, skirting, dado and pillar and similar work, laid over and including backing coat, in CM 1:4, 10 mm thick, jointed with grey cement slurry mixed with pigment to match the shade of the slab including taking down/dismantling old one complete all as specified and as directed

S&F machine cut and machine polished, green marble, 18-20mm thick on horizontal or vertical surface,as in window cills and jambs bedded, jointed and pointed with neat grey cement slurry and pointed with coloured or white cement with pigment to match over and including rendering coat of 10 mm thick in CM 1:4 incl taking down old one complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

S&F aluminum anodised grill DG- 202 ( 10 mm x 5.2mm) fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick all as specified and directed. Note : Minimum thickness of anodizing shall be 15 microns.

Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etc complete all as specified and directed

Supply only 4.80mm thick glass ordinary quality plain not exc 0.5 Sqm each pane with including wooden/rubber beading or gasket for aluminium section complete all as specified.

Supply only for 6mm thick bakelite sheet prelaminated both side with decorative choice laminations for aluminium frame work with including rubber beading or gasket for aluminium section complete all as specified.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F bands, straps supports or stay heavy for large gates, hook and pintle hinges clamps, hold fasts, wind ties, hooks for hanging fans and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for plain cement concrete type C1, 1:3:6, using 20mm graded stone aggregate as in bed block for hold fast, coping etc including necessary form work complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials steel and iron work, new or old of any description and girth, not otherwise described and treating ends of posts, back of chowkat etc with tar or coal tar black paint, area tarred exc 0.10 sqm but not exc 0.50 sqm each complete all as specified and directed

Ditto all as per item No 42 herein above but treating small articles such as stopper, covers, hold fast ends, posts back etc, not exc 0.10 sqm each complete all as specified and directed

Hacking out old brocken glass (any thickness, size, quality or description) from wooden / steel frame or stone, concrete or brick surrounding, glazed with putty or fixed with beads.

S&F for 4.0mm thick sheet glass ordinary quality and glazing with oil putty in steel windows and teak wood beading in wooden shutters square not exc 0.5 Sqm in each pane.

S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring of length 140mm fixed in floor etc complete all as specified and directed.

S &F, in repairs, aluminium alloy wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with in wooden windows, doors etc,and fixing of teak wooden beeding complete all as specified and as directed by the Engineer in charge.

Supply and fix aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 250 mm fixed at any position all as specified and directed.

S&F in stainless steel butt hinges, 100mm, medium weight complete all as specified and directed

S&F in extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed.

S&F in aluminium, anodised, barrel tower bolts of extruded section of size 150mm complete all as specified and directed.

S&F in mortice lock vertical type 75mm 04 lever brass for aluminium door with complete fittings all as specified and directed by EIC

S&F in Godrej night latch 4 lever for entrance door with fittings complete all as specified and directed

S&F in repairs 40mm dia, cuboard knobs brass, polished and fixed with nut, screw and washer of mild steel ,bright finished etc complete all as specified and as directed by the Engineer in charge.

Supply only 0.45mm thick Plain aluminium sheeting , alloy 31000 H4 in stepped flashing (measured as the minimum rectangle from which the pieces can be cut) bottom of panelled shutter complete all as spd and directed.

Supply only PVC cabinet mirror of size 600X450 mm complete all as specfied and directed.

Supply only harrison rails, mild steel , chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed

Supply only for 20mm dia fancy type chromium plated curtain rod brackets complete all as specified and directed

S&F CI floor trap 75mm dia outlet, with CP grating including jointing to waste pipe, fixed in plain cement concrete type B1 (1:2:4) & taking down old trap complete all as specified and as directed.

S&F CI floor trap 100mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & including taking down old trap complete all as specified and as directed.

S&F in repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

S&F in repairs vitreous china squatting pan, white, orissa pattern pan of size 580 mm x 440 mm of standard quality with integral foot rests,and including 'P' trap or 'S' Trap complete including connection to trap and to flushing pipe, anti syphonic pipe etc complete all as specified and directed.

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC etc, complete all as specified and directed.

S&F in repair for CP concealed stop cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply only CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply only CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

Supply only brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type. Make -Jaqur,Prayag polymers Pvt Ltd or equivalent.

Supply only CP pillar taps 15mm bore., cast copper alloy, chromium plated fancy type complete all as specified and directed.

Supply only 15 mm bore Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed.

Supply only waste fitting of 32 mm bore brass, chromium plated for glazed ware wash basin etc complete all as specified and directed..

Supply only waste fitting of 40 mm bore brass , chromium plated for glazed ware for sink coulpling etc complete all as specified and directed..

Supply only waste pipe for WHB/ sink 32mm bore fixed to wash hand basin/sinks coupling length pipe 0.90 mtrs each complete all as specified and directed..

Supply only 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and directed.

Supply only stainless steel grating in ground shape 100mm dia complete all as specified and directed.

-ditto- all as per item No 76.00 above but with hole complete all as specified and directed.

Supply only plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete all as specified and directed..

S&F stainless steel kitchen plate rack of make Prayag polymers Pvt Ltd or equivalent etc complete all as specified and directed .

S&F stainles steel sink with drainage board , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers including CI cantilever bracket, connecting union etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm including supply and fixing bib tap CP with long body screwed for iron pipe complete all as specified and directed.

S&F in repair low density polyethene pipes (LDPE) 40mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc.

Supply only chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

Supply only soap dish complete all as specified and directed.

Supply only brass chromium plated towel rail 20mm dia 'D' type 600mm long between flanges, with and including chromium plated brass screws etc complete all as specified and directed.

Supply only Toilet paper holder complete all as specified and directed.

Supply only Health faucet with 1 mtr tube & hook complete all as specified and directed.

Supply only two way Bib cock long body with wall flange fitted by 15mm bore complete all as specified and as directed

Supply only CP corner glass with brass bracket screws etc complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

S&F 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed.

Ditto all as per item No 91.00 above but 20 mm bore.

S&F in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed.

Dismantling floor, hearth or wall tiling and stone slabs including cement mortar bedding (but not backing), removing rubbish off the premises outside MD Land complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 Sqm but not exceeding 0.16 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for coloured 300x200x7mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete all as specified and directed.

Labour for cleaning /clearing of blockage of gully traps, floor traps, vertical soils/ waste pipe of different dia and sewage lines in the area of the Thane under GE (NW) Mankhurd Note: a) The labour (01 no) will report daily at 0845 hrs on all working days at complaint cell centre and attend complaints till 1645 hrs given by Engr -In- Charge . Complaints needs to be cleared within 24 hrs after receiving the complaints . The contractor will deploy requisite labour and supply all T&P ( mechanical Iron rods, knot ropes , bamboo etc) scaffolding ladders any other materials required to clear the blockages at the site without any extra cost .Labour for cleaning of sludge from sewage lines (any dia) to manhole is included in quoted rates. In case any labour does not report to Engineer In Charge for the whole day or found missing more than half an hour on any day, Panel recovery @ RS.860/- per head per day shall be made proportionally from contractor's dues. b) The above item includes conveyance cost of labour with their tools to travel from pocket to pocket to attend complaints including removal of sludge from the site outside MOD land to a distance not exc 5km (The department shall not be liable to provide any kind/form of transportation to the labour). (c) Registers of labour attendance and complaints shall be maintained by contractor at their own cost,which shall be kept in the custody of MES Department(complaint cell) duly signed by contractor's representative ,JE(civil) and Engineer in charge.

Opening cover of septic tank, of size 5 - 10 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position all as directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

Opening cover of septic tank, of size exc 10 - 15 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position all as directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

Opening cover of septic tank, of size exc 20 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position all as directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

Demolition of brick work or stone/boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles complete all as specified and as directed

Demolition of cement concrete ,un-reinforced in ground floors and paving not exceeding 15 centimetre thickness, below or above ground level complete all as specified and as directed.

Demolition of cement concrete ,(reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar , in 200 mm internal dia and taking out of trenches if required complete all as specified and as directed.

All as per item No 105.00 above, but 150mm dia pipe

Demolition /Dismantling of 200mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required

M&L Salt Glazed Stone Ware drain pipe, grade ‘A’ 200 mm bore laid in trenches and jointed complete all as specified and as directed. (Excavation and earth work shall be measured and paid separately).

All as per item No 108.00 above but 150mm dia

M&L reinforced concrete pipes, class NP - 2, 250 mm bore, laid and jointed complete with collars Complete all as specified and directed.

M&L for Concrete bed to drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and as directed

M&L for Concrete bed to drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed

All as per Serial No 113.00 herein above but exc 1.50m but n.exc 3.0m depth

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and as directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed

M&L Plain Cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M&L Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain complete all as specified and as directed.

M&L PCC 1:2:4 Type B-1 using 20mm graded stone aggregate as in benching, coping including necessary form work complete all as specified and as directed

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified & directed.

Extra over stone walling for Hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 20 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course complete all as specified. Note :- Hidden portion of masonry shall not be hammer dressed

Hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 40 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course complete all as specified Note :- Hidden portion of masonry shall not be hammer dressed

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with WPC as per manufacturer's instruction and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. Note:- WPC will be measured and paid for separately.

M& L for raised pointing to random rubble masonry uncoursed or brought upto courses in CM 1:4 , complete all as specified & directed.

M&L 15 mm thick cement plaster in CM 1:6 on stone masonry surfaces or surface other than fair faces of brick work or on one side of lathing complete all as specified and directed.

Supply only integral water proofing compound as per latest IS specification complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished flat concrete surfaces complete all as specified and directed.

M&L fo fair finished flat form work to edges of concrete flats, treads, breaks infloors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1 1:2:4 (20mm graded aggregate )Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specifiecd and directed.

M&L Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces complete all as specified and as directed

M&L Mild steel deformed/TMT bars 10 mm dia, cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire, annealed not less than 0.9 mm dia or securing with clips complete all as specified and as directed

Cutting into existing manhole, 150 mm bore pipe, for connecting new drains making good to pipe and removing cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates, smooth finish and re-forming benching complete all as specified and as directed

All as per Item No 133.00 here-in above but for 200 mm bore pipe

Cleaning of SGSW pipe lines 100 mm to 150mm bore pipe and removing the blockage by means of rodding with and including bamboo splits/flexible iron wire or concrete malacces rods from manhole to manhole, through pipes from trap to manhole, rendering the system clear and flushing the delogged line with sufficient quantity of water and removing sludge/waste material etc. to a distance n. exc 50 M and burrying in pits and re-filling the same complete all as specified and directed by the Engr-in-Charge. (Note :- The cost for excavation and earth work for pits is deemed to be included in the unit rate).

All as per Serial Item No 135.00 herein above but line of 200 mm bore pipe-ditto-.

All as per Serial Item No 135.00 herein above but line of 300 mm bore pipe-ditto-.

Cleaning of blocked Soil Pipe Vertical shaft 100/110 mm dia by opening inspection eye door of bend/ branch pieces, rodding till smooth flow and refixing of door after cleaning including necessary scaffolding all as specified and directed.

Cleaning manhole of size n.exc 1.50 Sqm by taking out sludge in semi liquid/solid stage (incl. all water etc) from inside of manhole of depth not exceeding 1.5 m and removing the sludge to a distance not exceeding 50m depositing in trenches including supply and sprinkling bleaching powder and covering sludge with earth to a thickness not less than 30 cm including all earth work, returning filling, removal of surplus soil & necessary temporary cleaning as directed by the Engineer-in-Charge.

All as per item 139.00 here-in-before but depth exceeding 1.5m but n.exc 3m deep.

S&F in repair 40mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed to walls. Ceilings or in floors etc complete all as specified and directed.

S&F in repair 110mm bore PVC(SWR) bends any radius with access door height of bldg is G+3 storey bldg or 18m ht bldg complete all as specified and directed.

S&Fin repair 110mm bore PVC(SWR) branch piece, double (double'Y') equal or unequal with access door complete all as directed

S&F in repair 110mm bore PVC(SWR) junction double (double T) equal or unequal with access door complete all as directed

S&F in repair 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls G+3 storey bldg or 18m ht bldg complete all as directed.

All as per item no. 145.00 above, but 75mm bore

S&Fin repair PVC(SWR) Q or P trap125/110 mm bore G+3 storey bldg or 18m ht bldg complete all as directed.

S&F in repair PVC(SWR) vent cowl G+3 storey bldg or 18m ht bldg complete all as directed.

S&F 40mm bore Rubber or vulcanite plugs (waste) with rings and fittings complete all as directed

S &F PVC (SWR) bends, 75 mm bore, any radius

S &F PVC (SWR) branch piece,double( double Y) 75mm bore equal or unequal

Supply & fixing 15 mm bore GI tubing, medium grade, ISI marked conforming to IS -1239 including providing and fixing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed

Supply & fixing 20 mm bore GI tubing, medium grade, ISI marked conforming to IS -1239 including providing and fixing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

Cutting holes in brick walls in cement mortar exc half brick but not exc one brick and making good dismanltled portion in cement mortar or cement lime mortar and stone walls built in lime mortar complete all as specfied and directed.

S&F cast iron covers and frame grade FG 150, suitable for sewage line manhole cover by making hole if required for members in each manhole and fixed with screws with nut and bolts and washers complete including locking arrangement complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion of concrete and making good disturbed in ground concrete brick work, masonary etc complete all as specified and directed.

Dismantling old chain link fencing of any size or mesh.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M & L PCC 1:3:6 type C2 (40 mm graded aggregate) in post of fencing complete all as specified and directed.

S & F PVC coated chain link fencing using 4 mm outer dia with GI wire 3.15 mm dia and mesh size 50 x 50 mm complete all as specified and directed.

S & F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long (Diameter of neck 16 to 20mm).

M&L for rendering 15mm thick on fair faces of brick or concrete work in CM 1:6, finished the surfaces even & smooth complete all as specified.

M& L for preparation of newly plastered surface of wall and applying three coats of white wash complete all as specified and directed by Engr-In-Charge.

S&F mild steel work as in posts or struts of fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, including all necessary drilling, bolting or riveting etc conforming to Fe- 290 Gde E-165 complete all as specified and directed.

S & F Rolled Mild Steel Framed work as in doors or Gates of angle or other section confirming to Fe 410 - W (Gde E-250) Quality 'B', with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

M & L for hard core of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified.

M&L 75 mm thick plain Cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in sub base of flooring finished without using extra cement complete all as specified and as directed

M & L 100 mm thick plain cement concrete type C-2 1:3:6 Using 40mm graded trap stone agg as in paths, etc including necessary use and waste of form work, finishing exposed edges fair for rounding,surfaces finished even and smooth without using extra cement and spike rolling to surfaces or making impressions of expanded metal whilst the concrete is green,laid in spans of 2.0 m and joints filled with paving bitumen and sand mixture (1:3) complete all as specified and as directed

M&L for pre cast concrete coloured with glazed finish(Lacquere finished) external interlocking paver block of M-30 grade, having compressive strength 30 N /mm2, 60mm thick of shade as approved by GE laid dry over sand cushion of average thickness 25mm duly consolidate,set and levelled the block in in proper level with interlocking laid in pavement including demolition of old paver block complete all as specified and directed. Note : The rate quoted shall be deemed to be enclusive of sand for bedding of paver block

M& L Pre Polished Chequred cement concrete tiles heavy duty 30cm x 30 cm x 20 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey white cement in equal proportions over screed bed or bedding layer of mortar 20 mm in cement mortar 1:6 complete all as specified and as directed

M&L for Durastone Heavy Duty digital tiles (300x 300) x 10-12 mm thick in floor set and jointed with neat cement slurry and pointed in coloured cement to match over screed bed or bedding layer of mortar 20 mm in cement mortar 1:6 complete all as specified.

S&F in repairs galvanised 2 strand, steel barbed wire 2.24mm dia bars 75mm spacing fencing incuding dismantled wire to be coiled neatly as directed.

S & F in repairs camouflage painted concertina coil fencing with punched tape concertina coil 600mm dia 10 meter openable length (total length 90m), having 50 Nos rounds per 6 meter length, springcore wire (2.5mm thick) of high tensile strength of 165 kg/sq.mm with tape (0.52mm thick) and weight 43.478 gm/metre and fixing the same with y-shape angle iron placed 1.50 mtr apart and with 6 horizontal R.B.T (reinforced barbed tape) wire, stud tied with G.I staple sand G.I clips to retain horizontal, including necessary bolts, complete all as specified and directed.

M& L for preparation surfaces of new wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for two coats synthetic enamel paint over and including red oxide zinc chrome primer of any description not other wise described over 10 cm width or girth including preparation of new or previously untreated steel surfaces. Note : A sum of Rs 32,835.00 towards sch of credit shall be deducted to arrive the contract sum.

BREEZE CONSTRUCTION

Sunil Construction

EVEREST POWER CONTROL ENGINEERS

Vinod Enterprises

sapana enterprises