SPECIAL REPAIR TO BLDG NO P-6/8 (TIGER JCOS MESS) UNDER GE SATWARI

Amount

B&R PORTION:- Complete removal of the existing mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified.

Demolition of brick tiles or terracing tiles, duble layer on roofs, complete all as specified.

Demolition of roof shingles (wood), complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410- W(Gde-E-250) quality A, complete all as specified.

Dismantiling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in ridge of roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick, GI angle 24mmx24mm and 0.4mm thick, bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm, ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid including taking down of old unsv materials, complete all as specified and directed by Engr-in- Chage. Make: Gyproc Make : JSW Colour or equivalent make as specified in apeendix of list of make as approved by GE.

Dismantling timber scantlings unframed work 40 sq.cm and over in section, in any position, complete all as specified.

Taking down chowkhats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified.

Taking down chowkhats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing from site complete all as specified.

Taking down shutters of any description n exc 1 sqm each, complete all as specified

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each, complete all as specified.

Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chanbered, put together with glue pinned at joints of 2nd class HW, complete all as specified.

35mm thik plain, framed, factory made panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial veneering particle board on both faces. The size of rail and stile as per IS : 1003(Part-1), kiln in seasoned and chemically pressure treated, complete all as specified.

30mm thick 2nd class HW, glazed and skelton shutters open rebated and prepared to receive glass / gauge (without sash bar) edges of forming plain chamfered orrounded fitted with cut and mitred bead for securing glass / gauge etc size of shutter as per SSR part-1 section 8 clause 8.24(a), complete all as specified.

18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Solid PVC dDoor frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing complete.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified.

75mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21, complete all as specified.

125 mm long extruded Aluminium handles, fabricated type, anodised complete all as specified.

75 mm long extruded Aluminium handles, fabricated type, anodised complete all as specified.

150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified.

75mm rim latch with two levers, of aluminium alloy body, anodised and fixed complete all as specified.

Two coats of synthetic enamel paint over a coat of pink primer on new plywood surface of any description, not otherwise described over 10 cm width or girth, including cleaning and dusting complete, all as specified and directed.

Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying two coats of synthetic enamel paint, complete all as specified.

Taking down cement plaster of any description on brick work including terrazo topping or tiles, racking out jointing hacking for key scrubbling down with water and removing all the demolished material outside cantt area, complete all as specified.

Rendering 15 mm thick in CM 1:6 on brick wall surface or concrete surface finished the surface even and smoth without using extra cement and applying two coats distemper oil emulsion & including a coat of wall care putty 1-3mm thick, complete all as specified.

Preparation of old treated plastered surfaces of wall and and applying two coat of distemper oil emulsion including preparation of old surfaces over & including a coat of wall care putty1-3mm thick, complete all as specified.

Rendering 15 mm thick in CM 1:4 on brick wall surface or concrete surface finished the surfaces even and smoth without using extra cement and applying two coats of cement base paint including priming surface with chalk whiting, complete all as specified.

Preparation of old plastered surfaces of wall and applying two coats of cement base paint complete all as specified.

Hacking out old broken glass (any thickness size, quality or description) from steel frames or stone, concrete or brick surrroundings, glazed with putty or fixed with beads, complete all as specified.

3 mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and, beads nails etc. to wooden surfaces as in square exc 0.50 sqm in each pane, complete all as specified.

Prepration of old treated steel surfaces of any description not otherwise described over 10 cm width or girth & applying two coats of synthetic enamel paint, complete, all as specified and directed.

Preparation of newly plastered surfaces of wall including filling of small holes etc. and applying three coats of of white wash, complete, all as specified and directed.

Preparation of old treated plastered surfaces of wall including filling of small halls etc and applying two coats of of white wash, complete, all as specified and directed.

Rendering 10mm thck in CM 1:3 or Plain Cement Concrete 1:2:4 type B-1 as in ceilings or conc surfaces such as chajjas, upward facia, downward facias and similar items finished even of smoth including dubbing coat without using extra cement upto any height including all necessary scaffolding and applying two coats of white wash on ceilings, complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Brick work with subclass 'B' old size bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6, complete all as specified.

Brick work with sub class ‘B’ brick straight or curved on plain to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified.

Cement concrete 1:2:4 type B1 using 20 mm graded crshed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified.

75mm thick plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate in plinth protection finished even and fair, complete all as directed.

Taking up or down steel tubing and connection bore of pipe 15mm dia, complete all as specified and as directed.

Taking up or down steel tubing and connection bore of pipe 20mm dia, complete all as specified and as directed.

Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Refixing old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, including cleaning of old tubing complete all as specified.

Refixing old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, including cleaning of old tubing complete all as specified.

Supply and fixing in repair bib tap cast copper alloy CP brass 15mm bore of pipe complete all as specified. Make : Prayag

Chromium plated fancy type Bib taps with flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore pipe fixed in repairs, complete all as specified. Make-Prayag Cat No 8608 or equivalent cat part of make as specified in Appx 'F'.

Pillar taps 15mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs, complete all as specified. Make-Prayag Cat No 8702 or equivalent cat part of make as specified in Appx 'F'.

PVC waste pipe 32 mm dia for Wash basin and urinals, complete all as specified.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed, complete all as specified.

PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets, 32mm dia PVC flush pipe fixed in repair, complete all as specified and directed. Make-Prayag Cat No-701 or equivalent cat part of make as specified in Appx 'F'.

Demolition of Concrete of any description and in any position not otherwise specifically provided for, complete all as specified.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in roof padding, mass concrete and similar work complete all as directed by Engr-in-Charge.

Reinforced cement concrete Type B-1, 1:2:4 (20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as directed by Engr-in-Charge.

TMT steel bars 10mm dia and above as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia), complete all as specified and directed.

TMT bars 6mm to 8mm dia, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Description all as per item No-62 above but 5mm dia and over upto and including 10mm dia as in stiruups, spacres and binderscomplete all as specified and directed.

Formwork to sides and soffits of rough finish surfaces of concrete floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams fair finished surfaces of concrete etc all as specified and directed.

Galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed in repairs with tinned tacks or galvanised wire staples, complete all as specified and directed.

Vitreous China, wash hand basin, flat back white of size 550mmx400mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, 32mm dia waste pipe,including cutting for and pinning in ends of brackets or erecting stand, complete all as specified Make-Prayag Cat No-4641 or equivalent cat part of make as specified in Appx 'F'.

Chromium plated Stop valves/angle valves with flange, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed for 15 mm bore fixed in repairs, complete all as specified. Make-Prayag(Waves) Cat No 8310 or equivalent cat part of make as specified in Appx 'F'.

Dismantling water tanks and removing from site capacity exceeding 250 litre and not exceeding 500 litre, complete all as specified.

Rotational moulded PVC Water Tank tripple layerd white (Cylinderical vertical with closed top) 500 litres capacity hoisted and fixed in position complete all as specified.

Float valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of bore 20mm.(Min weight 210gm), complete all as specified.

Vitreous china squatting ‘Pan’ Orissa pattern 580mm x 440mm, white, with integral foot rest including connection to trap, and to flush pipe, anti syphonage pipe etc including trap set in and including concrete and making good to floor complete all as specified. Make-Prayag Cat No-4051 or equivalent cat part of make as specified in Appx 'F'.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non - skid Digital Ceramic coloured tiles ,joint free (square/rectangular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of cement mortar (1:6) 15mm thick, complete all as specified.

Glazed cerramic coloured tiles of size 300x450x7mm thick set and jointed in neat cement slurry and pointed white or colored cement as in vertical surfaces fixed over a backing coats of CM 1:4,10 mm thick complete all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit / surface PVC casing caping medium grade of required size ISI marked with & including MS sheet metal sunken / terminal box 1.2mm thick of required size / module including white cover plate with frames & all necessory wall cutting and making good disturbed surface and all items as per the requirement of the work at site for modular fittings, complete all as directed and specified.

One light/fan point controlled by one, one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp independent complete all as specified.

One 3 pin socket outlet 6 amp on same board complete all as specified.

Description all as per srl item No 78 here in before but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Modular switch 1 way 6A, 1 module, (ISI marked), complete all as specified.

Modular Socket, 6A - 2/3 pin combined 2 module, (ISI marked), complete all as specified.

Modular Socket, 6A/16A - 2/3 pin combined 2 module, (ISI marked), complete all as specified.

Modular switch 1 way 16A, 1 module, (ISI marked), complete all as specified.

Modular fan step regulator, 120W - 2 module (ISI marked), complete all as specified.

Ceiling rose (ISI Marked) 3 Phase PVC/poly carbonate, insulated body, compete all as specified.

Tube light fitting box type suitable for LED 18-20W tube Rod with end cap made out of CRCA sheet powder coated complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 18-20LED tube rod 4 feet long complete all as specified and directed. Make:-Crompton Cat Part No:-LTT8-20 for LED tube rod & DMLN1LT8-16 for fittings or Equivalent cat part of make as specified in Appx 'F' here in after. Note :- The LED batten and LED tube rod shall be of same make.

Integrated LED Bulk Head luminaire comprises of a highly cost effective, compact, ultra low energy, huilt in engineering plastic housing with clear prismatic diffuser suitable for indoor and outdoor applications with IP 65 protection with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to bulk head fitting including Led lamp of 10W complete all as specified and directed. Make: C&S Electric Cat Part No CG80IB10WLED or Equivalent cat part of make as specified in Appx 'F' here in after.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

LED lamp 7W B-22 holder base with polycarbonate body, complete all as specified. Make:- C&S Cat Part No-LTHPLEDLAMP7W/B22 or Equivalent cat part of make as specified in Appx 'F' here in after.

Vertical distribution board TPN IP 43-'IK 09 with bus bars neutral links blanking plates double door suitable for FP MCCB as incommer and out going SP/TP MCBs 4 ways with & including MCCB four pole 125 Amp 415 volts of 16 KA breaking capacity with adjustable thermal, complete all as specified and directed. Make of VTPN:-INDOASIAN Cat part No :-811888 and Make of MCCB:-INDOASIAN Cat part No :-830243 or equivalent cat part of make as specified in Appx "B" here in after. Note:- MCCBs and DBs shall be of same make.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 12 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning with & including taking down old unsv DBs complete all as specified. Make:- INDOASIAN cat part No-811808 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB single pole and neutral 32 amps 240 volts 10 KA 'C' series all as specified. Make:- INDOASIAN cat part No-811151 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series all as specified. Make:- INDOASIAN cat part No-811122 to 811129 or Equivalent cat part of make as specified in Appx 'F' here in after.

Sub main wiring with single core cable 2x 6 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including 20mm cancealed PVC rigid conduit / surface PVC casing caping medium grade alongwith 1x 4 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface with & including taking down old unsv sub main wiring of any type, complete all as specified and directed. Note:-2 wire of 6sqmm,1 wire 4sqmm and one run of pvc conduit shall be measured as one unit.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironincluding PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

Single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 Amp 24 volts, complete all as specified

Supply and fixing AC single phase 240 Volts 50 HZ ,ceiling fan of size 1200mm Sweep complete in white colour ,5 Star rating with canopy with all accessories incl nuts,bolts,clamps etc. for fixing ceiling fan and provision of flexible copper conductor cable 3 core from ceiling rose to fan including taking down old unsv ceiling fan, complete all as specified and directed. Make :- Havells Cat Part No ES-50 Premium, Crompton Cat Part No Entrust 50 or equivalentas specified in list of make mentioned in Appx 'F'.

Supply & fixing down rod (hanging rod) made out of GI tubing 20mm bore medium grade for length upto 120cm suitable for fixing AC ceiling fan of size 1200mm / 1400mm sweep including orovn of holes for fixing nut & bolts, complete all as specified.

Taking down of the existing exhaust fan and Supply and fixing Exhaust fan 450 mm sweep, heavy duty, single phase AC 230/240V, with energy efficient motor ,pre-lubricated double ball bearing ,speed 900 rpm, complete with louvers for wall mounting incl grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. Note:- Old Unsv exhaust fan to be deposited in MES store yard.

M/S Shesh Paul Gupta

M/S K D Construction Co

Kanwal Nain Behl

M/S RAJ ENGINEERS

Tawi Constructions

M/S VIJAY KUMAR SHARMA