SPECIAL REPAIR REPLACEMENT OF EXTERNAL ELECT SUPPLY NETWORK AT MILITARY WING PXE CHANDIPUR AND CERTAIN REVENUE WORK AT AGE BR I AND AGE BR BALASORE

Amount

PART-I (SPECIAL REPAIR TO ALL THE TOILETS AT AYUDH BHAWAN BLDG NO P/640 AT PXE,CHANDIPUR) (B/R PORTION) Demolition of brick work built in cement mortar incl quoin, arches etc complete all as specified and directed.

Taking down cement plaster on wall; ceiling, roof etc incl racking out joints hacking for keys, scrubbing with etc complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rubbish off the premises complete all as specified and directed..

Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15cm thickness complete all as specified and directed. (Below or above Ground level)

Demolition of cement concrete (Reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius as Half brick wall built in CM 1:4 complete all as specified and directed.

Dismantling of stone slab and tiles laid bedded and pointed in any mortar of any description or thickness in floors, approons etc complete all as specified and directed.

Reinforced cement concrete (Nominal mix) Lintel Bands type B1 1:2:4 (20 mm graded aggregate) complete all as specified and directed.

Reinforced cement concrete (Nominal mix) Slabs supported on walls type B1 1:2:4 (20 mm graded aggregate) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips) complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams lintles cantlevers, shelves incl supports etc for rough finished surface of concrete complete all as specified and directed.

M & L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Labour only for rounding to edges of Granite stone slab one edge such as in shelves complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-1 ( Using 20 mm graded aggregates), in floor and to receive tiles complete all as specified and directed.

S&F non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc, and cement screed in CM 1:6, 20 mm thick and jointed in neat cement slurry and pointed complete all as specified and directed.

S&F Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and over rendering in CM 1:4, 10mm thick all as specified and directed.

M&L Rendering 10 mm thick cement plaster on internal surfaces of brick work in CM 1:6 andn surface to be finished even & smooth without using extra cement complete all as specified and directed.

Three coats of white wash on newly plastered surfaces on wall including preparation complete all as specified and directed.

M&L Preparation of old plastered surfaces of ceiling and applying one coats of white wash complete all as specified and directed.

S&F PVC door frame of standard size and section all as per manufacturer’s instruction complete fixed to brick wall complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frames shall be covered with head moulded plain colour PVC ‘C” channel having a PVC sheet strip of 20mm width struck insi complete all as specified and directed.

Butt hinges, extruded aluminium alloy with galvanised 100 mm long mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as directed by Engineer-in-Charge.

All as per item No.24 above but exc 1.5 Sqm and n.exc 4 Sqm each.

S&F Anodised aluminium power coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 12 mm thick veneered particle board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work complete all as directed by Engineer-in-Charge.

S&f Anodised aluminium powered coated door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, locking system, anodised aluminum snap beading screws etc. complete all as specified

S&F sheet glass 5.00 mm thick, ordinary quality and glazing with oil putty fixed in square n exc 0.5 Sqm each complete all as directed by Engineer-in-Charge.

S & F Anodised aluminium power coated ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays, hinges type(two Nos), suitable handle including locking system etc and necessary fitting with powder coated frame work complete all as specified

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate as in repairs complete all as directed by Engineer-in-Charge.

M&L for vitreous china squatting pan of Orissa pattern size 580 X 440 mm white 'P'trap with intregal foot rest (excluding flushing cystern and flush pipe) in repairs complete all as directed by Engineer-in-Charge. make: Paryware/Hindware

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in repairs complete all as directed by Engineer-in-Charge.

S&F vitreous china wash basin, white, of size 350x265mm, incl cutting for and pinning in ends of brackets or erecting on granite but excl taps, pvc conections but incl brackets in repairs complete all as directed by Engineer-in-Charge. (Prayag : Cat Pat No 4704)

S&F vitreous china urinal half stall type white(excluding flushing cistern (including flush pipe & Waste coupling) complete including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe complete all as directed by Engineer-in-Charge.

S&F 15 mm dia CP pillar cock , cast copper alloy screwed for iron pipe (Prayag :Cat Part No 7402)

S&F PVC waste pipe of size 32mm complete all as directed by Engineer-in-Charge.

S&F glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long complete all as directed by Engineer-in-Charge.

36. S & F for soap container of PTMT fixed with and incl chromium plated brass screws and wooden/plastic cleat complete all as directed by Engineer-in-Charge.

S&F aluminium anodised tubular towel rail 20mm dia "D" type 60 cm long between flange complete all as directed by Engineer-in-Charge.

S&F in repairs 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as directed by Engineer-in-Charge.

S &F in repairs 15mm CP angular stop cock with flange (Make : Prayag cat part No 8310 complete all as directed by Engineer-in-Charge. Brand-waves

S&F 15 mm size PVC connections with PTMT nuts of length 450 mm complete all as directed by Engineer-in-Charge.

S&F CP soap case complete all as directed by Engineer-in-Charge.

M&L health faucet Abs with double lock 1.2 meter stainless steel flexible hose and wall hook complete all as directed by Engineer-in-Charge.

Taking down 100mm internal dia of AC drain pipe set in cement mortar complete all as directed by Engineer-in-Charge.

S & F 100mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors/wall complete all as directed by Engineer-in-Charge.

S&F PVC(SWR) junction single (double T) equal or unequal of bore 110mm bore incl provided with access door complete all as directed by Engineer-in-Charge. (SUPREME/PRINCE/ORIPLAST)

As per item No 56 above here-in before but of bore 75 mm complete all as directed by Engineer-in-Charge.

S & F 110 mm PVC (SWR) bends complete all as directed by Engineer-in-Charge.

S & F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors/wall complete all as directed by Engineer-in-Charge.

S & F 40mm Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches complete all as directed by Engineer-in-Charge.

S & F 75mm PVC (SWR) vent cowl complete all as directed by Engineer-in-Charge.

S&F PVC grating doom 100 mm dia complete all as directed by Engineer-in-Charge.

PVC (SWR) Gully trap 125/110 mm , setting and jointing with solvent cement complete all as directed by Engineer-in-Charge.

Dismantling water tanks any type of capacity Exc 500 but n.exc 1000 liters and removing to store complete all as directed by Engineer-in-Charge.

S&F Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 litre complete all as directed by Engineer-in-Charge.

S/F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 20mm bore in repair complete all as directed by Engineer-in-Charge.

S&F Gun metal 20 mm bore dia of pipe globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipes medium grade 15 mm dia with all fittings and fixed to walls and ceilings or laid in floors complete all as directed by Engineer-in-Charge.

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 15mm bore complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipe medium grade 20 mm dia bore as in walls complete all as directed by Engineer-in-Charge.

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20mm bore complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 25 to 32mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipe medium grade 25 mm dia bore as in walls complete all as directed by Engineer-in-Charge.

S&F in repairs 15mm dia two way chromium plated angle cock (Somany Cat Part No 210509) complete all as directed by Engineer-in-Charge.

M &L Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as directed by Engineer-in-Charge.

S&F Toughened glass urinal partition including screws with woden/plastic cleats complete all as directed by Engineer-in-Charge. (Make : Prayag/Jaquar/johnson)

PART-II (SPECIAL REPAIR TO GROUND FLOOR TOILET AT PROOF BHAWAN AT PXE,CHANDIPUR) (B/R PORTION) Demolition of brick work built in cement mortar incl quoin, arches etc complete all as specified and directed.

Taking down cement plaster on wall; ceiling, roof etc incl racking out joints hacking for keys, scrubbing with etc complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and rubbish off the premises complete all as directed by Engineer-in-Charge.

Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15cm thickness (Below or above Ground level) complete all as directed by Engineer-in-Charge.

Demolition of cement concrete (Reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius as Half brick wall built in CM 1:4 complete all as specified and directed.

Reinforced cement concrete (Nominal mix) Lintel Bands type B1 1:2:4 (20 mm graded aggregate) complete all as directed by Engineer-in-Charge.

Reinforced cement concrete (Nominal mix) Slabs supported on walls type B1 1:2:4 (20 mm graded aggregate) complete all as directed by Engineer-in-Charge.

Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or secur;ing with clips complete all as directed by Engineer-in-Charge.

-Ditto- but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders

Use and waste of form work to sides and soffits of floor or roof beams lintles cantlevers, shelves incl supports etc for rough finished surface of concrete complete all as specified and directed.

M & L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed by Engineer-in-Charge.

Labour only for rounding to edges of Granite stone slab one edge such as in shelves complete all as directed by Engineer-in-Charge.

M&L 25 mm thick PCC 1:2:4 type B-1 ( Using 20 mm graded aggregates), in floor and to receive tiles complete all as specified and directed.

S&F non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc, and cement screed in CM 1:6, 20 mm thick and jointed in neat cement slurry and pointed complete all as directed by Engineer-in-Charge.

S&F Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and over rendering in CM 1:4, 10mm thick all as specified and directed

M&L Rendering 15 mm thick cement plaster on internal surfaces of brick work in CM 1:6 andn surface to be finished even & smooth without using extra cement.

Three coats of white wash on newly plastered surfaces on wall including preparation.

M&L Preparation of old plastered surfaces of ceiling and applying one coats of white wash .

S&F PVC door frame of standard size and section all as per manufacturer’s instruction complete fixed to brick wall.

S&FFactory Made Solid PVC Moulded Door Shutter, with particle board 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

Butt hinges, extruded aluminium alloy with galvanised 100 mm long mild steel hinge pin, anodised and fixed, type B-21

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as directed by Engineer-in-Charge.

All as per item No.25 above but exc 1.5 Sqm and n.exc 4 Sqm each.

S&F Anodised aluminium power coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 12 mm thick veneered particle board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work.

S&f Anodised aluminium powered coated door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, locking system, anodised aluminum snap beading screws etc. complete all as specified

S&F sheet glass 5.00 mm thick, ordinary quality and glazing with oil putty fixed in square n exc 0.5 Sqm each complete all as directed by Engineer-in-Charge.

S & F Anodised aluminium power coated ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays, hinges type(two Nos), suitable handle including locking system etc and necessary fitting with powder coated frame work complete all as specified

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate as in repairs complete all as directed by Engineer-in-Charge.

M&L for vitreous china squatting pan of Orissa pattern size 580 X 440 mm white 'P'trap with intregal foot rest (excluding flushing cystern and flush pipe) in repairs complete all as directed by Engineer-in-Charge. make: Paryware/Hindware

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as directed by Engineer-in-Charge.

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in repairs complete all as directed by Engineer-in-Charge.

S&F vitreous china wash basin, white, of oval type size 350x265mm, incl cutting for and pinning in ends of brackets or erecting on granite but excl taps, pvc conections but incl brackets in repairs complete all as directed by Engineer-in-Charge. (Prayag : Cat Pat No 4704)

S&F 15 mm dia CP pillar cock , cast copper alloy screwed for iron pipe complete all as directed by Engineer-in-Charge. (Prayag :Cat Part No 7402)

S&F vitreous china urinal half stall type white(excluding flushing cistern (including flush pipe & Waste coupling) complete including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe

S&F PVC waste pipe of size 32mm.

S&F glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long

36. S & F for soap container of PTMT fixed with and incl chromium plated brass screws and wooden/plastic cleat.

S&F aluminium anodised tubular towel rail 20mm dia "D" type 60 cm long between flange complete all as directed by Engineer-in-Charge.

S&F in repairs 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as directed by Engineer-in-Charge.

S &F in repairs 15mm CP angular stop cock with flange (Make : Prayag cat part No 8310 Brand-waves complete all as directed by Engineer-in-Charge.

S&F 15 mm size PVC connections with PTMT nuts of length 450 mm complete all as directed by Engineer-in-Charge.

S&F CP soap case complete all as directed by Engineer-in-Charge.

M&L health faucet Abs with double lock 1.2 meter stainless steel flexible hose and wall hook complete all as directed by Engineer-in-Charge.

S & F 110 MM PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors/walls complete all as directed by Engineer-in-Charge.

S&F PVC (SWR) 75 mm junction single, (Single T) equal or unequal complete all as directed by Engineer-in-Charge.

S&F PVC(SWR) bend of 75mm bore complete all as directed by Engineer-in-Charge.

S & F 110 mm PVC (SWR) bends complete all as directed by Engineer-in-Charge.

S & F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors/wall complete all as directed by Engineer-in-Charge.

S & F 40mm Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches complete all as directed by Engineer-in-Charge.

S & F 75mm PVC (SWR) vent cowl complete all as directed by Engineer-in-Charge.

S&F PVC grating doom 100 mm dia complete all as directed by Engineer-in-Charge.

S/F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 25mm bore in repair complete all as directed by Engineer-in-Charge.

S&F Gun metal 25 mm bore dia of pipe globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipes medium grade 15 mm dia with all fittings and fixed to walls and ceilings or laid in floors complete all as directed by Engineer-in-Charge.

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 15mm bore complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipe medium grade 20 mm dia bore as in walls complete all as directed by Engineer-in-Charge.

Fixing only, ‘Medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20mm bore complete all as directed by Engineer-in-Charge.

Taking up or down steel tubing 25 TO 32mm bore and connections, including cleaning for re-fixing or removal to store complete all as directed by Engineer-in-Charge.

S&F GI pipe medium grade 25 mm dia bore as in walls complete all as directed by Engineer-in-Charge.

S&F in repairs 15mm dia two way chromium plated angle cock complete all as directed by Engineer-in-Charge. (Somany Cat Part No 210509)

M&L CP Urinal spreader including all acessories for fixing with 15 mm dia pipe complete all as directed by Engineer-in-Charge. (Prayag Cat Part No BEA 25)

S&F Toughened glass urinal partition including screws with woden/plastic cleats complete all as directed by Engineer-in-Charge. (Make : Prayag/Jaquar/johnson)

PART-III ( Special Repair to Roof at ECHS building at OT Road,Balasore) Dismantling of asbestos cement (corrugators or semi corrugated) sheet as in roof covering complete all as directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position ( un framed work) complete all as directed by Engineer-in-Charge.

S&F 0.50 mm thick corugated Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 0.50 mm thick plain Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as directed by Engineer-in-Charge.

M&L 2nd Class hard wood in scantling clean sawn timber fixed all as specified.

M&L preparing surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with 2 coats creosote oil all as specified.

PART-IV ( Special repair to all toilets of Ayudh Bhawan Bldg No-P-640 at PXE Chandipur) (E/M PORTION) Taking down carefully copper/aluminium point wiring including sunken M S Boxes (Light, Fan, socket or power) complete,(fitting such as switches,ceiling roses,call bell,pendants,regulators,socket etc by unscrewing from board carefully and making good disturbed surfaces of walls,floors etc complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLS of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable FRLS of size 1.5 Sqmm for earth continuity wire, to be drawn in and including PVC conduit heavy duty with concealed wiring, MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cap washers for one light/Fan point controlled by one single way switch including all necessary wall cutting and making good disturbed surface all as directed and specified.(Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

All as per item No.2 here in before but for 5/15 Amps point on independent board with two runs of 4.0 Sqmm FR grade PVC insulated unsheathed stranded Copper conductor and 4.0 Sqmm, FR grade PVC insulated, unsheathed, stranded copper conductor as earth wire.(Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

All as per item No. 2 above but for independent 5 Amps switch socket out let using 1.5 Sq mm wire with 1.5 Sqmm wire for earth continuity conductor.(Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

Supply and fixing including connection of switch piano flush button type single pole one way 5 Amps (Make:Anchor/Cona/Roma)

Supply and fixing including connection of switch socket combination 5/16 Amps,5 in 1, 2/3 pin flush type.(Make:Anchor/Cona/Roma)

Supply and fixing including connection of switch socket combination 5 Amps,2 in 1, 2/3 pin flush type.(Make:Anchor/Cona/Roma)

Supply and fixing of ceilings rose of PVC polycarbonate isolated body three terminals,surface bakelite 65mmx50mm complete all as directed by Engineer-in-Charge. (Make:Anchor/Cona/Roma)

Taking down unserviceable sub main /Sub circuit wiring of any type and size including conduit, batten wiring for necessary repair/replacement complete all as directed by Engineer-in-Charge.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable FRLS of size 2 x 4.0 Sqmm and earth continuity conductor cable FRLS of size 1 x 4.0 Sqmm to be drawn into PVC conduit concealed wiring complete all as directed by Engineer-in-Charge.

S&F MCB DB made of sheet steel phosphatised, powder painted double door with bus bar, neutral link, earth bar and din rail of SPN 6 way, 240 Volts fixed in wall,making good disturbed surfaces, including taking out old DB with fittings & fixtures complete all as specified. (Make/Model :Cat No:DBSPN006DD of L&T or Standard / Legrand )

S&F MCB, SPN. 6-32 Amps rating 240, volt, 'C' series, 10 kA (Make L&T,Cat No.BB20320C or Standard/Legrand)

S&F MCB, SP, 6-32 Amps, 240 volt, 'C' Series, 10 kA ( Make L&T,Cat No.BB10320C or Standard & Legrand ).

Supply and fixing 1x10 watt ( 2ft ) LED Baton indoor decorative type Integral sleek polycarbonate LED Channel with white acrylic cover complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fittings complete all as specified and directed. ( Make /Model No :-BCLSB 10 NW of Bajaj or equivalent of Crompton/Jaquar/ Century Magic.

Supply and fixing Highly robust industrial Box type LED extruded Batten type indoor decorative type luminaire suitable for LED Tube 1 x 16/20 watt (4ft ) complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fittings complete all as specified and directed. ( Make /Model No :-IGP161LT8-16( ECO-I ) of Crompton or equivalent of Bajaj/JaquarPhillips)

S & F LED Polycarbonate T8 Tube with in built driver with metal heat sink double sided connection of capacity 1x 20 watts all as specified and directed,Make/Model No:-LT8-20-865-(2) ULTRON of Crompton or equivalent of Bajaj/ Phillips/ Jaquar

PART-V ( Special Repair to Ground Floor toilets at Proof Bhawan at PXE Chandipur) (E/M PORTION) Taking down carefully copper/aluminium point wiring including sunken M S Boxes (Light, Fan, socket or power) complete,(fitting such as switches,ceiling roses,call bell,pendants,regulators,socket etc by unscrewing from board carefully and making good disturbed surfaces of walls,floors etc complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLS of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable FRLS of size 1.5 Sqmm for earth continuity wire, to be drawn in and including PVC conduit heavy duty with concealed wiring, MS sheet metal switch/Terminal box 1.2 mm thick and hylum switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cap washers for one light/Fan point controlled by one single way switch including all necessary wall cutting and making good disturbed surface all as directed and specified.(Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

All as per item No.2 here in before but for 5/15 Amps point on independent board with two runs of 4.0 Sqmm FR grade PVC insulated unsheathed stranded Copper conductor and 4.0 Sqmm, FR grade PVC insulated, unsheathed, stranded copper conductor as earth wire complete all as directed by Engineer-in-Charge. (Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

All as per item No. 2 above but for independent 5 Amps switch socket out let using 1.5 Sq mm wire with 1.5 Sqmm wire for earth continuity conductorcomplete all as directed by Engineer-in-Charge. (Make of wire: Finolex/Polycab/Plaza and Make of PVC Conduit :-Plaza/Prestoplast/Precision)

Supply and fixing including connection of switch piano flush button type single pole one way 5 Amps complete all as directed by Engineer-in-Charge. (Make:Anchor/Cona/Roma)

Supply and fixing including connection of switch socket combination 5/16 Amps,5 in 1, 2/3 pin flush type complete all as directed by Engineer-in-Charge. (Make:Anchor/Cona/Roma)

Supply and fixing including connection of switch socket combination 5 Amps,2 in 1, 2/3 pin flush type complete all as directed by Engineer-in-Charge.(Make:Anchor/Cona/Roma)

Supply and fixing of ceilings rose of PVC polycarbonate isolated body three terminals,surface bakelite 65mmx50mm (Make:Anchor/Cona/Roma)

Taking down unserviceable sub main /Sub circuit wiring of any type and size including conduit, batten wiring for necessary repair/replacement complete all as directed by Engineer-in-Charge.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable FRLS of size 2 x 4.0 Sqmm and earth continuity conductor cable FRLS of size 1 x 4.0 Sqmm to be drawn into PVC conduit conceald wiring complete all as directed by Engineer-in-Charge.

S&F MCB DB made of sheet steel phosphatised, powder painted double door with bus bar, neutral link, earth bar and din rail of SPN 6 way, 240 Volts fixed in wall,making good disturbed surfaces, including taking out old DB with fittings & fixtures complete all as specified. (Make/Model :Cat No:DBSPN006DD of L&T or Standard / Legrand )

S&F MCB, SPN. 6-32 Amps rating 240, volt, 'C' series, 10 KA complete all as directed by Engineer-in-Charge. (Make L&T,Cat No.BB20320C or Standard/Legrand)

S&F MCB, SP, 6-32 Amps, 240 volt, 'C' Series, 10 KA complete all as directed by Engineer-in-Charge. ( Make L&T,Cat No.BB10320C or Standard & Legrand ).

Supply and fixing 1x10 watt ( 2ft ) LED Baton indoor decorative type Integral sleek polycarbonate LED Channel with white acrylic cover complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fittings complete all as specified and directed. ( Make /Model No :-BCLSB 10 NW of Bajaj or equivalent of Crompton/Jaquar/ Century Magic.

Supply and fixing Highly robust industrial Box type LED extruded Batten type indoor decorative type luminaire suitable for LED Tube 1 x 16/20 watt (4ft ) complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable including taking down old light fittings complete all as specified and directed. ( Make /Model No :-IGP161LT8-16( ECO-I ) of Crompton or equivalent of Bajaj/JaquarPhillips)

S & F LED Polycarbonate T8 Tube with in built driver with metal heat sink double sided connection of capacity 1x 20 watts all as specified and directed,Make/Model No:-LT8-20-865-(2) ULTRON of Crompton or equivalent of Bajaj/ Phillips/ Jaquar

PART-VI (Special Repair / Replacement of External Elect Supply Network at Mil Wing, PXE Chandipur) Dismantling of ACSR conductors with earth wire from Overhead lines complete all as directed by Engineer-in-Charge.

Dismantling of cross-arms of M.S. channels or angle sections etc.with clamps,nuts & bolts and round washers complete all as specified and directed.

Dismantling of Insulators of any type and any size complete.

Dismantling of GI Cable protection pipe of any dia or any sizes with all fittings along the poles and under ground and repair the PCC/Coping to its original shape and sizes all as specified and directed..

Supply, laying & testing U/G cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) with stranded aluminum conductor, 1100 volts grade, of size 10 Sqmm 2 core complete all as directed by Engineer-in-Charge.

All same as per above item No-89 but of size 16 sqmm 2 core.

All same as per above item No-89 but of size 50 sqmm 3.5 core.

All same as per above item No-89 but of size 70 sqmm 3.5 core.

All same as per above item No-89 but of size 95 sqmm 3.5 core.

All same as per above item No-89 but of size 150 sqmm 3.5 core.

All same as per above item No-89 but of size 185 sqmm 3.5 core.

Excavation in trenches not exc 1.5m deep and n.exc 1.5m wide and getting out in soft/loose soil for foundation etc or for shafts, wells cess pits, manholes etc n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/loose soil. laying of cable line etc complete.

Supply and laying approved quality sand underneath and all around the U/G cable in trenches for cable cushioning all as specified and directed.

M & L Sub class ‘B’ bricks laid flat, transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable complete all as directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layer not exceeding 25 Cm complete all as directed by Engineer-in-Charge.

Removing of excavated material not exceeding 50 m and depositing where directed at level not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as directed by Engineer-in-Charge.

M & L for GI pipe 40mm dia light grade with all fittings and complete to walls and ceilings or laid in trenches/ for cable protection complete all as directed by Engineer-in-Charge.

Supply and laying of GI tubing light grade 50 mm with all fittings in trenches/road crossing for protection of cable of size 50 mm bore complete all as directed.

Cutting chases,pinning in,making good of PCC hard standing to facing where required and pointing in cement mortar 1:3 , exc.10 cm. but not exc.20 cm girth to ends or edges of landing,steps,cills,sunshades,shelves,lintels,etc.and cutting chases for concealed water tubing or concealed conduit wiring,laying of cables and making good with old shape and size all as specified and directed.

Cutting Bituminous road in,making good with facing where required and pointing exc.30 cm. but not exc.1.0 mtr. girth to ends or edges of landing,steps,cills,sunshades,shelves,lintels,etc.and cutting chases for concealed water tubing or concealed conduit wiring,laying of cables and making good with old shape and size all as specified and directed.

M&L for cleaning,scrubing and preparation of surfaces of PCC pole and carrying out following phase of work all as directed. (a) cement based paint on all the sides of PCC pole, area above the zebra painting all as specified & directed. (b) carrying out painting by synthetic enamel paint one coat over the concrete surface of pole using black and yellow paint all as directed area above the pole coping upto 1.5 mtr and numbering the pole all as specified (c) Silver colour spray painting of mild steel bracket, clamps and nut, bolts all as specified and directed.

Material and labour for heat shrikable type LT Jointing kit for 1.1 KV XLPE cables of size 25-50 sqmm 3.5/4 core straight through joint complete . (Make Denson/ Multishrink/ 3M)

Material and labour for heat shrikable type LT Jointing kit for 1.1 KV XLPE cables of size 70-95 sqmm 3.5/4 core straight through joint complete. (Make Denson/ Multishrink/ 3M)

Supply & Fixing repairs cable junction box made of thermoplastic, halogen free, weather proof with metric Knock outs for cable entry including four/five pole terminals and cable entry glands for incomming, out going and connection cable with protection grade IP-66/67 of size 205x255x112 mm and suitable for LT under ground cable any size/capacity including bracing clamp,bolts,nuts & washers. (Make Hensel/ model No-KF2525B or equivalent as approved)

Supply & Fixing , in replacement, PVC copper cable Twin core of size 1.5sq mm for junction box to street light fitting connection. (Make: Finolex/ Polycab/ Plaza)

Supply & Fixing, in replacement, PVC conduit pipe of size 20mm for protection of copper wire to be fixed on elect pole. (Make: Plaza/Precision/prestoplast)

Supply & Fixing, in replacement, flexible hose pipe of size 20mm protection of copper wire (Make: Plaza/Precision/prestoplast)

Supply and fixing in repair of GI pipe Bracket of 40 mm dia light grade pipe bend to shape of approx length 1.5 Mtr including 2 no. MS Clamp of flat iron size 40x6 mm complete with nut, bolt, washers all as specified and directed. (Make of GI pipe- Jindal/Prakash/Tata)

Taking down old unserviceable LT Panel and Supply, install, and testing LT Panel board made of CRCA sheet 3.15 mm thick , metal clad, rigid, totally enclosed, cubical type, outdoor type with sloping canopy on top, siemens grey powder coated, fully compartmentalised, floor mounted, factory made, corrosion resistance, prewired suitable for 415 volt, 3 PH, 4 wire, 50 HZ, AC supply system of adequate shape and size. Bus bar shall be of three phases and neutral system of 400 Amps rating, rectangular cross section duly air insulated by insulation with colour code mounted on porcelain insulators,housed in separate compartment, LED phase indicators, CTs etc.The manufacturer of panel shall submit a copy of CPRI test report of degree of ingress protection IP 54 in accordance with IEC 60529. Panel should be designed as per latest Indian Standards. Gasket between all adjacent units and beneath all covers shall be provided to render the joints dust proof. Base chanel of 75x75x5 mm or as per weight of panel should be provided at bottom and fixed on MS angle of appropriate size. Ground clearance of base chanel should not be less than 45 cm and height of panel should not be more than 2000 mm. MS angle base of panel is to be fixed in cement, concrete and mortar to withhold the weight of panel. Panel shall comprises of following:-

(A) IN COMING (a) MCCB four pole 415 Volts AC Supply 400 A, 36 kA, with adjustable microprocessor release, Ics =100% Icu - 01 Nos. (b) Multi function meter with digital dispay for measuring Voltage (0-500 Volts), Current(0-500 Amps) and frequency - 01 No (B) OUT GOING (a) MCCB 4 Pole, 415 Volts 36 kA, 320 Amp with adjustable microprocessor release, Ics =100% Icu -01No. (b) MCCB 4 Pole ,415 Volts,35/36 kA 100 Amp with adjustable microprocessor release, Ics =100% Icu- 02 Nos. (c) MCCB 4 Pole, 415 Volts,36/35 kA 63 Amp with adjustable microprocessor release, Ics =100% Icu-02 Nos (d) MCB (SPN) 63 Amps,'C' Series -03 Nos (e) MCB (SPN) 40 Amps,'C' Series -03 Nos (Make of panel :L&T/Universal Switch gear control/Schneider).

Taking down old unserviceable LT Panel and Supply, install, and testing LT Panel board made of CRCA sheet 3.15 mm thick , metal clad, rigid, totally enclosed, cubical type, outdoor type with sloping canopy on top, siemens grey powder coated, fully compartmentalised, floor mounted, factory made, corrosion resistance, prewired suitable for 415 volt, 3 PH, 4 wire, 50 HZ, AC supply system of adequate shape and size. Bus bar shall be of three phases and neutral system of 400 Amps rating, rectangular cross section duly air insulated by insulation with colour code mounted on porcelain insulators,housed in separate compartment, LED phase indicators, CTs etc.The manufacturer of panel shall submit a copy of CPRI test report of degree of ingress protection IP 54 in accordance with IEC 60529. Panel should be designed as per latest Indian Standards. Gasket between all adjacent units and beneath all covers shall be provided to render the joints dust proof. Base chanel of 75x75x5 mm or as per weight of panel should be provided at bottom and fixed on MS angle of appropriate size. Ground clearance of base chanel should not be less than 45 cm and height of panel should not be more than 2000 mm. MS angle base of panel is to be fixed in cement, concrete and mortar to withhold the weight of panel. Panel shall comprises of following:-

(A) IN COMING (a) MCCB four pole 415 Volts AC Supply 400 A, 36 kA, with adjustable microprocessor release, Ics =100% Icu - 01 Nos. (b) Multi function meter with digital dispay for measuring Voltage (0-500 Volts), Current(0-500 Amps) and frequency - 01 No (B) OUT GOING (a) MCCB 4 Pole, 415 Volts 36 kA, 320 Amp with adjustable microprocessor release, Ics =100% Icu -01No. (b) MCCB 4 Pole ,415 Volts,35/36 kA 100 Amp with adjustable microprocessor release, Ics =100% Icu- 02 Nos. (c) MCCB 4 Pole, 415 Volts,36/35 kA 63 Amp with adjustable microprocessor release, Ics =100% Icu-02 Nos (d) MCB (SPN) 63 Amps,'C' Series -03 Nos (e) MCB (SPN) 40 Amps,'C' Series -03 Nos (Make of panel :L&T/Universal Switch gear control/Schneider).

Taking down old unserviceable LT Panel and Supply, install, and testing LT Panel board made of CRCA sheet 3.15 mm thick , metal clad, rigid, totally enclosed, cubical type, outdoor type with sloping canopy on top, siemens grey powder coated, fully compartmentalised, floor mounted, factory made, corrosion resistance, prewired suitable for 415 volt, 3 PH, 4 wire, 50 HZ, AC supply system of adequate shape and size. Bus bar shall be of three phases and neutral system of 250 Amps rating, rectangular cross section duly air insulated by insulation with colour code mounted on porcelain insulators,housed in separate compartment, LED phase indicators, CTs etc.The manufacturer of panel shall submit a copy of CPRI test report of degree of ingress protection IP 54 in accordance with IEC 60529. Panel should be designed as per latest Indian Standards. Gasket between all adjacent units and beneath all covers shall be provided to render the joints dust proof. Base chanel of 75x75x5 mm or as per weight of panel should be provided at bottom and fixed on MS angle of appropriate size. Ground clearance of base chanel should not be less than 45 cm and height of panel should not be more than 2000 mm. MS angle base of panel is to be fixed in cement, concrete and mortar to withhold the weight of panel. Panel shall comprises of following:-

(A) IN COMING (a) MCCB 4 Pole, 415 Volts 36 kA, 320 Amp with adjustable microprocessor release, Ics =100% Icu -01No. (b) Panel mounted multi function meter for measuring Voltage (0-500 Volts), Current(0-500 Amps) and frequency - 01 No (B) OUT GOING (a) MCCB 4 Pole, 415 Volts 36 kA, 160 Amp with adjustable microprocessor release, Ics =100% Icu -01No. (b) MCCB 4 Pole ,415 Volts,35/36 kA 100 Amp with adjustable microprocessor release, Ics =100% Icu- 01 No. (c) MCCB 4 Pole, 415 Volts,36/35 kA 63 Amp with adjustable microprocessor release, Ics =100% Icu-02 Nos (d) MCB (SPN) 63 Amps,'C' Series -03 Nos (e) MCB (SPN) 40 Amps,'C' Series -03 Nos (Make of panel :L&T/Universal Switch gear control/Schneider).

Supply and fix, bus bar chamber totally enclosed metal clad, current rating 100 Amp, 4 way to be fixed with angle frame and grouted in PCC as specified and directed.

M&L Earthing with galvanized steel earth plate electrode of size 60cm x 60cm x 6 mm thick,buried directly in ground(earth pit not less than 2.25 meters deep below ground Level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanised iron strip size 25 mm x 4mm as earth lead by means of bolts, nuts, check nuts and washers etc, GI earth lead strip duly protected by 40 mm dia GI pipe (light grade) and 20 MM GI pipe (medium grade) for watering and connected to control switch as directed including necessary earth work in soft/loose soil and disposal of soil to a distance not exceeding 50 Mtrs, PCC (1:3: 6) type C1 in concrete pit,50mm thick precast RCC (1:2:3) type A1 as in cover slab duly reinforced with 8 mm dia TMT bar @ 100 mm c/c both way and two nos lifting handle made out of 10 mm dia TMT bar and set in cement mortar (1:4), testing etc complete and as specified in electrical plate No 3 of SSR part-I

vaishnavee devi ent

DS ENTERPRISES