Loading
Loading…
Loading…
Tender Value
₹2.3 Cr
EMD Value
₹2.7 L
Closing Date
18 Feb 2026, 1:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TECHNICAL
15 conditions · 4 needing a document upload
Clause Regarding GST: (a) All the Bidders/tenderers should ensure that they are GST Compliant and their quoted tax Structure are as per GST LAW.(b) Tenderer Should Furnish their GSTIN numbers representing the States in Which they are registered GST, along with address of Registered Office.(c)The Contract is under GST Act and rules as applicable time to time.
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. Annual Contractual Turnover Data for the Previous 3/4 Years should be submitted as per Annexure-IX.(Annexure- VIB of Tender Documents)
39 conditions · 11 needing a document upload
Check List: The tenderer(s) would fill up the check list, as per Annexure-XXIII to ensure that they are submitting the complete tender offer.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Augmentation of FKG Dedicated Rly Feeder, Provision of AAAC Covered Conductor in 11KV Lines and Aerial Bunched cables in LT Lines at TSK Division.
LV-T-14-TSK-929~NFR
LV-T-14-TSK-929
Open
Works - General
14 Months
Tinsukia, Assam
₹0
₹2.7 L
18 Feb 2026
28 Jan 2026
4 Feb 2026
70 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,42,96,962 | ||
| — | 100.00 | — | — | ||
| Supply, excavation, erection, testing and commissioning of 12-metre long GI tubular pole of type SP-64, having base diameter 219.1 mm, middle diameter 193.7 mm and top diameter 165.1 mm, with minimum thickness of 4.85 mm at base and middle and 4.50 mm at top, and approximate weight of 292 kg. The work includes supply of all foundation materials and erection of the pole in cement concrete foundation of mix 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate of 40 mm nominal size), including excavation of pit, centering and shuttering, proper alignment, concreting, curing, refilling and disposal of surplus earth, complete in all respects as per site conditions and directions of the Supervisor-in-Charge. | — | — | — | 54,69,300 | |
| — | 3510.00 | — | — | ||
| Supply, drawing, strengthening and stringing of ACSR conductor 6/1/3.35 mm (Rabbit) on HT overhead lines, including laying of conductor on ground, lifting and placing on poles, tensioning with approved tension clamps, binding on insulators, and providing jumpers asrequired. The work also includes supply and fixing of all associated fittings and accessories such as tension clamps, nuts, bolts and hardware, ensuring standard sagging in each and every span. The work shall be carried out complete in all respects as per relevant specifications, safety norms and directions of the Supervisor-in-Charge. | — | — | — | 1,29,870 | |
| — | 8000.00 | — | — | ||
| Supply, laying, stringing and binding of 11 kV, 1 Core x 50 sq.mm Medium Voltage Covered Conductor (MVCC) of Raychem make or equivalent, suitable for overhead distribution application. The conductor shall be an All-Aluminium Alloy Stranded Covered Conductor (AAAC MVCC) having longitudinal water blocking and triple-extruded insulation with UV-resistant high quality polymer that provides protection against accidental contacts, reduces faults due to vegetation or animals, and improves reliability of power distribution lines. The covered conductor shall be suitable for 11 kV system operations and designed to meet applicable standards for medium voltage overhead covered conductors (e.g., EN 50397-1 or equivalent). Covered conductor insulation shall prevent tracking/erosion and provide dielectric protection under outdoor conditions.The work also includes supply and fixing of all associated fittings and accessories such as tension clamps, nuts, bolts and hardware, ensuring standard sagging in each and every span. The work shall be carried out complete in all respects as per approved drawings, relevant specifications, safety norms and directions of the Supervisor-in-Charge. | — | — | — | 18,37,040 | |
| — | 80.00 | — | — | ||
| Supply, fitting and fixing of GI channel of size 100 x 50 x 6 mm, 250 mm long, on tubular pole for pole structure, including provision of necessary MS/GI clamps of size 50 x 6 mm. The work includes drilling of required holes on pole/channel, supply and fixing of all associated accessories such as nuts, bolts, washers and hardware, proper alignment and secure fastening. The item is complete in all respects as per approved drawings, site conditions and directions of the Engineer-in-Charge. | — | — | — | 9,120 | |
| — | 80.00 | — | — | ||
| Supply, fitting and fixing of GI channel of size 100 x 50 x 6 mm, 1200 mm long, on tubular pole for pole structure, including provision of necessary MS/GI clamps of size 50 x 6 mm. The work includes drilling of required holes on pole/channel, supply and fixing of all associated accessories such as nuts, bolts, washers and hardware, proper alignment and secure fastening. The item is complete in all respects as per approved drawings, site conditions and directions of the Engineer-in-Charge. | — | — | — | 43,840 | |
| — | 60.00 | — | — | ||
| Supply, fitting and fixing of GI channel of size 100 x 50 x 6 mm, 2500 mm long, on tubular pole for pole structure, including provision of necessary MS/GI clamps of size 50 x 6 mm. The work includes drilling of required holes on pole/channel, supply and fixing of all associated accessories such as nuts, bolts, washers and hardware, proper alignment and secure fastening. The item is complete in all respects as per approved drawings, site conditions and directions of the Engineer-in-Charge. | — | — | — | 68,520 | |
| — | 60.00 | — | — | ||
| Supply, fitting and fixing of GI angle of size 50 x 50 x 6 mm, 3000 mm long, including cutting, drilling of holes, and supply and fixing of all necessary clamps, brackets, nuts, bolts, washers and accessories. The item is complete in all respects for proper mounting on pole/structure as per approved drawings, site conditions and directions of the Engineer-in-Charge. | — | — | — | 58,200 | |
| — | 80.00 | — | — | ||
| Supply, fitting and fixing of GI angle of size 50 x 50 x 6 mm, 1500 mm long, including cutting, drilling of holes, and supply and fixing of all necessary clamps, brackets, nuts, bolts, washers and accessories. The item is complete in all respects for proper mounting on pole/structure as per approved drawings, site conditions and directions of the Engineer-in-Charge. | — | — | — | 38,800 | |
| — | 90.00 | — | — | ||
| Supply and binding of 11 kV polymeric disc insulator of 70 kN rating, including supply and fixing of complete hardware fittings such as ball and socket arrangement, clevis, arcing horn (where required), shackles, pins, nuts, bolts and washers. The insulator shall be made of high-quality polymer with FRP core and silicone rubber housing, suitable for outdoor overhead line application. The work includes proper binding of conductor, ensuring correct alignment and electrical clearances, complete in all respects as per relevant IS/IEC standards, approved drawings and directions of the Engineer-in-Charge. | — | — | — | 66,780 | |
| — | 270.00 | — | — | ||
| Supply, fitting and fixing of 11 kV polymeric type pin insulator 5KN , including supply and fixing of galvanized pin, nuts, bolts, washers and all necessary hardware fittings. The insulator shall be of high-quality polymer with FRP core and silicone rubber housing, suitable for outdoor overhead line application. The work includes proper mounting, alignment and binding of conductor, complete in all respects as per relevant IS/IEC standards, approved drawings and directions of the Engineer-in-Charge. | — | — | — | 93,420 | |
| — | 25.00 | — | — | ||
| Supplying and erection of galvanised stay set for 11 kV overhead lines, complete with 19/20 mm diameter x 1.8 metre long GI stay rod, anchor plate of size 450 mm x 450 mm x 7.5 mm thick, thimble, stay clamps, turn buckle of size 20 mm x 600 mm, 7/4.00 mm diameter GI stay wire, and 11 kV strain insulator, including all necessary fittings and accessories. The work also includes providing cement concrete foundation in CC 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate of 40 mm nominal size), excavation of pit, placing of anchor plate, proper alignment, concreting, curing, refilling and disposal of surplus earth. The item is complete in all respects as per approved drawings, site conditions, relevant standards and directions of the Engineer-in-Charge. | — | — | — | 1,36,375 | |
| — | 6.00 | — | — | ||
| Supply, installation, testing and commissioning of 11 kV, 3-phase GO-DO fuse unit of 400 Amps capacity, including dismantling/removal of existing GO-DO fuse wherever required and replacement with new unit. The work includes supply and fixing of MS channel cross-arm of size 100 x 50 x 6 mm, operating handle/operating pipe, insulators, fuse carriers, contacts, and provision of one complete set of spare bare fuse elements. The item is complete with all necessary hardware fittings, alignment, electrical connections, testing for proper operation and commissioning, complete in all respects as per relevant IS/IEC standards, approved drawings and directions of the Engineer-in- Charge. | — | — | — | 1,09,782 | |
| — | 5.00 | — | — | ||
| Supply, installation, and fixing of 11KV Lightning Arrester (LA) set, rated 9kV (RMS) with 10kA discharge capacity, zinc-oxide type, suitable for outdoor mounting, complete with all accessories, clamps, connectors, earthing provisions, and tested for satisfactory operation as per IS 1881/IEC 60099. | — | — | — | 14,835 | |
| — | 300.00 | — | — | ||
| Boring of 2.6m length underneath railway track and laying of 200mm dia HDPE pipe PN8 for underground cable, including supply of HDPE pipe, complete with excavation, alignment, backfilling, and making it ready for cable passage. The HDPE pipe shall be of high-density polyethylene, conforming to IS 4984, PN8 rating, capable of withstanding rail load and soil pressure, and suitable for underground cable installation beneath railway tracks as per standard norms and safety requirements. | — | — | — | 15,42,000 | |
| — | 3000.00 | — | — | ||
| Supply, laying, connection , testing and commissioning of 11 KV HT , Single Core ,120 SQ. mm compact circular aluminium conductor, conductor screen with extruded semi conducting compound, , XLPE insulated , insulation screening with extruded semi conducting compound in combination with copper tape ( 0.3KA for 1 sec) , cores laid up, innersheath of PVC tape , galvanised steel flat strip armoured , and overall pvc sheathed cable conforming to is 7098 / (part-ii) 1985 with the latest amendments. For cable laying Excavation of earth depth 0.90 Mtrs. into breadth 0.508 Mtrs. below the ground level and a layer of course sand of 7.5 CM thickness shall be spread over the ground before laying the cable and the cable shall be covered with a layer of course sand of 7.5 CM thickness. The bottom of cable trench shall be leveled and got rid of any sharp material. Above the Layer of Course Sand 3 inch Size Brick is to be provided for protection of cable. Cable route markers to be provided at an interval not less than 50 Mtrs. All conditions to be fulfilled as per DRG No : PCEE/ELG/DRG/2024/2 Dtd 04.10.2024. | — | — | — | 38,11,110 | |
| — | 60.00 | — | — | ||
| Supply, fitting, and fixing of heat-shrinkable outdoor type cable termination kit for 11kV single-core 120sq.mm cable, complete with insulation, sealing, earthing, installed and tested as per IS 13573 / IEC 60502-4 standards. | — | — | — | 4,23,000 | |
| — | 1101.00 | — | — | ||
| Supply, drawing, straining & binding of GI guard wire on pole structure by GI bearer wire of 8 SWG & 10 SWG cross wire(1 route length consist of 2 mtrs. 8 SWG & 1 mtr.10 SWG GI wire). | — | — | — | 22,020 | |
| — | 1.00 | — | — | ||
| "Supply, fitting, fixing, testing and commissioning of of Indoor Type LT panel board. The panel shall be metal-enclosed, free-standing compartmentalized, modular type suitable for Indoor installation. The panel shall be dust and vermin proof and the enclosure shall provide a degree of protection of not less than IP-52. Control panel shall be fabricated out of 14 SWG cold rolled steel plates & properly supported using angles & channels. The whole panel shall be mounted on a base frame made out of suitable structural, preferably ISMC Channels. Joints of any kind in sheet shall be seam welded, all welding slag grounded off and welding pitwiped smooth with plumber metal. All panels and covers shall be properly fitted and square with the frames and holes in the panel correctly positioned. The Panel shall be fully compartmentalised with front and back opening doors.. When compartment door is opened, busbar and cable alley shall be shrouded by barrier plates. All panels shall be provided with suitable cable alley and vertical bus bar alley.Each cable chamber shall have cable entry from bottom and suitable removable gland plates shall be provided for this purpose. The cable chamber shall be provided with suitable supporting arrangement between the gland plate and terminals, in the middle. The cable chamber shall have a minimum width of 300 mm depending upon the outgoing cables. Each chamber shall be provided with a hinged type door opening away from the cable alley and shall be provided with black flowertype thumb screw which shall ensure tight closing. The edges of the door shall be provided with a neoprene rubber gasket to make the compartment dust proof.. The panel shall consists of the following Switchgears: ( BUS BAR=400 Amps TPN Aluminium) (i)MCCB 4 pole 400 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection=2 NO (ii) Onload Changeover Switch 4 Pole 600 Amps=1 NO (iii) BUS BAR=600 Amps TPN Aluminium Outgoing: (i) MCCB 4 Pole 250 Amps, 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection- 3 Nos (ii) MCCB 4 pole 125 Amps 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection-4 Nos (iii)MCCB 4 pole 63 Amps 25KA BC Ics=100%Icu , Thermal Magnetic OL & SC Protection-3 Nos (iv)LED three phase indication lamp RYB for incoming mains. (v) Digital Voltmeter LED indication with inbuilt selector switch (0-500 V) -1 Sets (vi) Digital Ammeter LED indication with inbuilt selector switch (40-400 Amps) -1 Sets " | — | — | — | 2,92,330 | |
| — | 30.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .