PROVN OF SINGLE LIVING ACCN FOR 04 X NCO, SPL REPAIR TO LT PANELS AND FEEDER PILLAR BOXES AND CONNECTED WORKS, SPL REPAIR FOR CONVERSION OF OH LT LINE TO UG LT CABLE NETWORK AN ALLIED WORKS AND REV NOS 14, 15, 42 AND 84 UNDER GE (EAST) MATHURA

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, laying cable etc. and getting out in soft/loose soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, laying cable etc. and getting out in soft/disintegrated rock (PCC/Tar road).

M&L for PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified.

M&L for Treating the top surface of filled earth in floor at the rate of 5 litres chemical emulsion in water of one percent Chlorpyrifos 20 EC emulsion per square metre of surface area.

M&L for Treating the soil under plinth protection at the rate of 5 litres chemical emulsion in water of one percent Chlorpyrifos 20 EC emulsion per square metre of surface area

M&L for Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified.

M&L for Brickwork with old size fly ash brick, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified.

M&L for 40mm thick damp proof course in cement concrete M-15 grade (Nominal mix) using 12.50 mm graded stone aggregate including necessary form work & water proofing compound as per manufacturer instruction.

M&L for use & waste of steel formwork (Rough finished flat) to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams and similar works complete all as specified & directed.

M&L for RCC M-25 grade (Design mix) as in foundation, footings, plinth Beam and similar works all as specified and directed.

M&L for use & waste of steel formwork (Rough finished flat) to sides of concrete pillar, posts and cloumns square /rectangular complete all as specified & directed.

M&L for RCC M-25 grade (Design mix) as in Columns, pillars, piers, posts and struts & similar works all as specified and directed.

M&L for use & waste of steel form work (Rough finished flat) to side and soffits of floor or roof beams lintels cantilevers shelves including supports etc complete all as specified and directed.

M&L for RCC M-25 grade (Design mix) as in Beams, cantilevers, bressummers, lintels & similar works complete all as specified and directed.

M&L for use & waste of steel form work (Rough finished flat) to chulla hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for RCC M-25 grade (Design mix) as in chajjas.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc n. exc 200mm thick etc complete all as specified and as directed.

M&L for RCC M-25 grade (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed.

M&L for use & waste of steel formwork to edges of suspended slabs n.exc 200mm thickness for flat rough finish surface complete all as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm thick using excavated soil all complete all as directed.

Removing excavated soil to a distance exc 250 m but n exc 500 m and depositing where directed at a level of n.exc 1.5 m above the starting point all complete all as directed.

M&L for TMT bars (FE-500 Grade) 10 mm dia and over cut to length and bent to shape required including cranking, bending, spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for TMT bars (FE-500 Grade) 8 mm dia cut to length and bent to shape required including cranking, bending, hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for TMT bars (FE-500 Grade) 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length and bent to shape required including cranking, bending, spirally for hooping for columns hooking end and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surface of slab, beam & ceiling surfaces finished even and smooth without using extra cement all as specified and directed.

M&L for rendering 15mm thick (10mm + 5mm) in two coats in cement mortar 1:4 on fair faces of brick/ concrete surfaces the surface even and fair, using 200 ml of liquid water proofing per bag of 50 Kg cement complete. Note :- Liquid water proofing compound shall be measured & paid seprately under relevant item of this BOQ.

Supply only Liquid water proofing compound

M&L for rendering 10 mm thick on brick wall or concrete surface in cement mortar 1:6 finishing even & fair all as specified and directed.

M&L for rendering 10 mm thick on ceiling surfaces in cement mortar 1:4 all as specified and directed.

M&L for preparing newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed. Note:- Weather proof acrylic exterior paint/primer shall be applied machinacally by latest machine such as truecase Graco or equivalent having minimum pressure of 330PSI. Make :- ASIAN PAINT (APEX)/BERGER PAINT (WEATHER COAT SMOOTH)/NITCO (OUT SHINE)

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over one coat primer over and including one coat of cement base chalk whitening applied as per manufacturer's instruction complete. Note :- Oil bound distemper /primer shall be applied machinacally by latest machine such as truecase Graco or equivalent having minimum pressure of 330PSI.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper all as specified and as directed by Engineer-In-Charge. Note :- Oil bound distemper /primer shall be applied machinacally by latest machine such as truecase Graco or equivalent having minimum pressure of 330PSI.

M&L for hardcore of broken stone or boulder gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface complete.

M&L for 75 mm thick PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in sub base to floors and paving etc all complete all as directed.

M&L for 100 mm thick PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in sub base to floors and paving etc all complete all as directed.

M&L for chequred cement concrete colured tiles glossy finish, rubber moulded with grey cement and pigment 30cm x 30cm x25mm thick, machine pressed set jointed and pointed in neat cement slurry in floors, with and including 20mm thick screed bed in CM 1:4 all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified.

M&L for Glazed ceramic tiles in vertical surface 450x300x7mm /300x450x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick backing coat in cement mortar in 1:4 complete all as specified.

M&L for 50 mm thick plain cement concrete M-10 grade (Nominal mix) using 20 mm graded stone aggregate) as in plinth protection surfaces finished even and smooth without using extra cement including filling the joints by bitumen and sand mixed in the ratio 1:4 by weight complete all as directed.

M&L for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle, filling the cracks by crack filler, providing 25 thick polymer modified plaster in ratio 1: 10 (1part of polymer and 10 parts of cement) with solid contents not less than 30% over slab, applying priming coat of epoxy primer with resin and hardener with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurethane liquid membrane not less than 500 micron thick UV stable having SRI value greater that equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurethane liquid membrane not less than 500 micron thick UV stable having SRI value greater that equal to 105 with consumption of 0.61 Kg/Sqm over 1st coat once it is dry Make : Asian paint/Thermax or equivalent make as approved by GE.

S&F Pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, with a shop coat of red oxide primer complete all as specified.

M&L cement concrete M-10 grade (Nominal mix) using 12.50mm graded stone aggregate as in blocks for fixing hold fasts and fillling of chowkhats or any other purpose all as specified.

M&L for applying two coats of synthetic enamel paint on primed steel surface over 10cm width or girth complete all as specified and directed.

S&F 35mm thick 2nd class hardwood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F powder coated aluminium frame (Powder coating shall not be less than 50 micron) for door, windows, ventilators (sliding , fixed or casement) with one or more rebates including joining cleat for fixing etc, complete all as specified.

M&L for powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. Note : (i) Glass panes shall be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it shall not be weighed and not paid separately.

S&F Powder coated (Minimum thickness of powder coating shall not be less than 50 micron of approved colour) aluminium window and ventilator shutters, side hung/ sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.)/ Pair of rollers at bottom of shutter, suitable handle (1 no.)/ Mortice type side locking arragement in shutter complete all as specified and as directed. Note : (i) Glass panes shall be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it shall not be weighed and not paid separately.

S&F for 5.5mm thick tinted glass in squares exc 0.5 sqm each pane including rubber bead jointing cleat for fixing in position for aluminium window/ventilator all as specified and directed.

M&L for 75mm powder coated aluminium barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 150mm powder coated aluminium barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 4 levers mild steel body mortice lock, vertical type, size 100mm fixed to aluminium door complete all as specified.

S&F 35 mm thick flush shutters, solid core construction with block board core and plywood face panel commercial type on both side all as specified.

S&F 40 mm thick flush shutters, solid core construction with block board core and plywood face panel commercial type on both side all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply & fix 125 mm size extruded aluminium alloy handles fabricated all as specified.

Supply & fix 150 mm long aluminium handles fabricated type anodised all as specified.

Supply & Fix 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed.

M&L Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

M&L Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples.

M&L for door closer aluminium die cast body hydraulically regulated designation No 3 universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F 5 mm Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

Supply & Fix 100 mm long aluminium anodised barrel tower bolts of extruded section and fixed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with M.S. square tube,supplying & fixing in opening as per specification & drawing complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified.

S&F in repair 25 mm dia, chromium plated curtain rod with fixing brackets, stops, rollers etc.complete all as specified.

Supply & fix 100mm long extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Cutting holes in existing wall or PCC Block masonry built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate as required depth of embedded portion of holdfast or lugs measured from the face of jamb into the wall exceeding half brick but not exceeding one brick all as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S&F 15 mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed Make :- ESSCO cat part No APR 101037

S&F white vitreous china urinal half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in white cement complete.

S&F 15mm dia bore Stop valves/Angle cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make : Cat Part No ESSCO APR-101053

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F in repair wash basin mixer 15mm bore. Make :- Essco cat part No APR 101011B or equivalent approved make.

S&F vitreous china wash hand basin,white, flat back size 580x450 mm including fixing to wall with brackets and including 15 mm dia pillar tap cast copper alloy , with capstan head , chromium pated, screwed down high presure, with long screwed shaks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F viterous china wash down water closet (pedstal pattern) complete . Incl toilet paper holder, seat cover health fow jet(inclduing flushing cistern and flshing pipe) all as specified complete all as specified and directed.

S&F in repair glass shelf 600mm long. Make :- Jaguar cat part No CAN 1171N or equivalent make as approved by GE.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms)

S&F Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour. (Minimum weight 40gms) Make : ESSCO cat part No APR-101281 ESH-1931or equivalent make as approved by GE.

S&F PVC waste pipe of 75 cm complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F in repairs 15mm bore PVC connection with PTMT nuts of length 450mm.

S&F PTMT towel rail , 60cm long (Minimum Weight 190 gms) fixed with and including chromium plated brass screws and wooden/plastic cleats.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75 mm PVC (SWR) pipe type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F 110 mm PVC (SWR) pipe type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F 110 mm PVC (SWR) pipe type 'A' single socketed in any length with rubber ring joints fixed to walls.

S&F 75 mm dia PVC (SWR) bends complete all as specified.

S&F 75 mm PVC (SWR) bend with access door fixed to pipe complete all as specified.

M&L for 150x150mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P'.

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal with accesss door.

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified.

S&F 110 mm bore PVC (SWR) Vent Cowl fixed to pipe complete all as specified.

Supply and fix 500 litre capacity white colour six layer ISI Marked rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position including making inlet/oulet connection and fitting tank connection complete all as specified and as directed.

Supply and fix 1000 litre capacity white colour six layer ISI Marked rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position including making inlet/oulet connection and fitting tank connection complete all as specified and as directed.

Supply and Fix 20 mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.

S&F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Removing excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point.

M&L for PCC M-10 grade (Nominal mix) using 40mm graded stone aggragate an in fdn of manholes.

M&L for PCC M-10 grade (Nominal mix) using 40mm graded stone aggragate as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore.

M&L for 150mm dia salt glazed stone ware drain pipe grade A laid in trenches and jointed as specified

M&L for PCC M-15 grade (Nominal mix) using 20mm graded stone aggragate as in coping surface channels, benchings etc of manholes finished fair and even.

M&L brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L for Precast RCC M-25 (Design mix) as in cover slabs for manholes.

Extra for forming fair finished channel or drain 30cm ginth (inner ginth) in cement concrete using extra cement incl forms, moulds stopped.

Dismantling corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Approved earth in floor using soil obtained from excavation after removing turff & boluders spreading, incl filling, leveling and well ramming in layer n exc 25 cm thick.

M&L for providing 25 mm thick PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in floor finish complete.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of newly plaster surface of ceiling and applying three coats of white wash complete.

S&F in repairs corner glass shelf. Make :- ESSCO cat part No ACN 1173 or equivalent make as approved by GE.

S&F in repairs glass shelf 600mm long. Make :- Jaquar cat part No ACN 1171N or equivalent make as approved by GE.

S&F in repairs Soap Dish holder all as specified Make :- ESSCO cat part No AEC-1131 or equivalent make as approved by GE.

S&F in repairs toilet paper holder. Make :- Jaquar cat part No AKP35753P or equivalent make as approved by GE.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate smooth finshed and reforming benching as required for 150mm bore pipe.

M&L PCC M-7.5 grade (Nominal mix) using 40 mm garded stone aggregate as in bed to drain pipe inclduing racking under an haunching against the sides of pipes after they are laid and tested for 150 mm dia pipe complete all as specified

S&F in repair towel ring all as specified. Make :- Essco AEC 1121 or equivalent make approved by GE.

S&F vitreous china bowl urinal flat back size 465x355x265mm including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe).

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L for 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted on GI framework fixed in ceiling complete all as specified.

Dismantling of asbestos cement (corrugated semi corrougated etc) sheets in roof covering including ridge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws as specified.

Dismantling floor, heath or wall tiling inclduing cemtn mortar bedding complete and removing rubbish off the premises.

M&L for 18-20 mm thick machine cut machined polished kota stone slab flooring over cement screed bed laid and jointd with pigment to match the shade of the slab including rubbing and polishing over & including screed bed and bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:3 size of Kota stone as decided by Engr-in-charge complete.

M&L for 18-20 mm thick machine cut machined polished kota stone slab in trade & riser over cement screed bed laid and jointd with pigment to match the shade of the slab including rubbing and polishing over & including screed bed and bedding layer of mortar 10 mm thick for laying floor finishes in CM 1:3 size of Kota stone as decided by Engr-in-charge complete.

Taking down cement or cement lime plaster on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water, etc.

M&L for rendering 15mm thick in cement mortar 1:6, on other than fair faces of brick work or concrete surfaces, finished the surfaces even and smooth without using extra cement all as specified and directed.

M&L for complete scraping down of old decorative surface of walls with steel wire brushed of smoke spots, moulds, moss efflorescent salts inclduding filling of spots with POP/putty and making smooth surfaces and applying two coats of oil bound distemper over a coat of primer over one coat of putty not less than 1mm thick all as directed. Note:- Oil bound distemper /primer shall be applied machinacally by latest machine such as truecase Graco or equivalent having minimum pressure of 330PSI.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 Sqm each, complete all as specified and directed.

S&F 100mm stainless steel butt hinges medium weight cold rolled all as directed

M&L for preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth not other wise described and applying two coats of synthetic enamal paint over a coat of red oxide primer all as specified & directed.

Dismantling of timber framed work scantling 40sqcm and over in section, in any position all as directed.

M&L for timber framed work and fixed 2nd class hard wood clean sawn in scantlings all as specified and directed.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc. ) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fitting etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed.

Taking down carefully by submain wiring/service connection of any type complete all as directed by Engr-in-charge.

Taking down old unserviceable existing DB/ enclousers any size /any discriptions as iron sheet scrap including MCB any type/size and making good distrubed surface/wall as per existing complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed FRLS cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall / roof incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes suitable for modular fittings including modular cover plate with frame for mounting modular switches, sockets, etc including earth wire of PVC insulated FRLS copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge , as described below:-

One light point controlled by one way switch 6 amp complete.

One Ceiling Fan /Exhaust fan point controlled by one way switch 6 amp complete.

One 3 pin 5 Amps socket point controlled by one switch on independent board.

One 3 pin 5 Amps socket point controlled by one switch on same board.

One bell point controlled by one push button on independent board.

All as per item No. 151 but for 3 pin / 5 pin 16 Amps sockets outlet with 4 Sqmm PVC insulated & unsheathed FRLS copper conductor cable independent complete all as specified and as directed .

M&L for Sub Main Wiring with two runs single core 6 Sqmm PVC insulated unsheathed FRLS cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 6 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. Note :- Two run of 6 Sqmm single core cable, one run of 6 Sqmm earth wire & one run of PVC conduit will measured as one unit length.

Supply and Fixing fancy ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified. Make :- SSK/Anchor/Cona/ Havells.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified. Make :- SSK/Anchor/Havells.

Supply and Fixing Modular switch 16 Amp single pole one way,1 Module all as specified. Make :- SSK/Anchor/Havells

Supply and Fixing Bell multi music type 230 Volts complete with connection all as specified & directed.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified. Make :- SSK/Anchor/Havells.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified. Make : - Anchor/Havells.

Supply and Fixing Modular Fan regulator electronic step type 120watt, 2 Module complete all as specified. Make :- SSK/Anchor/Havells.

Supply and fixing Modular bell push switch 6 Amps with indicator single pole one way 1 Module complete all as specified. Make :- SSK/Anchor/Havells

Supply and fixing fancy Lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified. Make :- SSK/Anchor/Havells.

Supply and fixing Pendant Lamp holder (B-22 base type) with shed cover including extension cable and 15 watt LED lamp complete suitbale for office table pendent light with complete fitting all as specified. Make :- SSK/Anchor/Havells.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts, co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make:- Havells (as per Cat Part No: LUMILINEBS20WLED 865 SPC WH) or equivalent to CG/Bajaj/Philips

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1x 9 watt LED Tube fitting (size not less then 600x25x40 mm) with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge. Make:Havells (as per Cat Part No: LUMILINEBS9WLED865 SPC W H) or equivalent to CG/Bajaj /Philips

Supply and fixing environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head back-lit LED luminaire comprising of high brightness LEDs lamp of 10 Watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and as directed. Make: Havells ordering cat part No HEXAFT10WLED 857SSY MBOPC or equivalent in Bajaj/ Philips/ Wipro /CG

Supply and fix LED 15W lamp suitable for normal holder( Base Cap B22) complete all as specified. Make : Havells or equivalent to Philips / Bajaj / CG

S&F MCB distribution board, SPN 4 Way, Double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified. Make :- Havells/Legrand/ABB / C&S.

S&F MCB distribution board, SPN 8 Way, Double door, sheet steel, phosphatised, powder painted with Copper bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, complete all as specified. Make :- Havells/Legrand/ABB / C&S.

Supply & fixing MCB SP 6 - 32 Amps, ' B' series ,bracking cap10KA complete all as specified and directed. (02 Spare) Make :- Havells- or equivalent of Legrand /L&T/ C&S / ABB

Supply & fix MCB SPN 6-32 Amps,' C' series , bracking cap10KA, 240V complete all as specified and directed. Make : Havells or equivalent of Legrand/L&T C&S/ ABB.

Supply & fix MCB SPN 40 Amps, 'C' series , bracking cap10KA, 240V complete all as specified and directed. Make : Havells or equivalent of Legrand/L&T C&S/ ABB.

Supply & fix SP enclosure with a two pin and earth plug and socket complete with SP MCB of rating 20 Amps, 240 Volts complete with all connection as directed. Make :- Havells or equivalent of Legrand /L&T/C&S.

Supply and install of 30W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified. Make of fitting : Havells (as per Cat Part No : ENDURACITYLITEPLAT PLUSSL30WLED757SASYBOPC) or equivalent in Crompton Greaves/ Bajaj/Philips / C&S (meeting all the above specification). Make of LED : CREE/ Nichia/ Osram/ Lumiled/ Bridgelux.

M&L for building security light bracket made out of 40mm dia light grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as directed taking down old unserviceable bracket as scrap any size / description. Make of Pipe : JINDAL/TATA/PRAKASH

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

M&L for Tubes, light grade, galvanised with all fitting laid in trenches for protection of earthing lead from mechanical injuryor tempering.of size 15mm complete all as specified and directed. Make :- Jindel/TATA/Surya/Prakash

M&L for GI earth lead 4 mm burried in ground / fixed on walls complete with ffixing screws, nut, bolts etc complete all as specified and as directed.

Supply and fix exhaust / Ventilating fan 150mm sweep mettallic alongwith louvers, Air Delivery 300 Cum/Hrs, 2000RPM, 25 Watt, alongwith louvers/ grill complete suitable to work on AC, single phase, 230 Volts , 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm. Make : Havells -Model Ventil Air DXW and equivalent of Bajaj / Crompton greves / Orient

Supply and fix exhaust fan 300mm sweep Mettallic type alongwith louvers suitable to work on AC, single phase, 230 Volts, 1400 RPM , 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm. Make : Havells -Model Ventil Air DB and equivalent of Bajaj / Crompton greves / Orient

Supply and fix ceiling fan 1200 mm sweep , Energy Saving models, Pearl white / white in colour 350 RPM, 220 volt 50 Hz complete with canopy, down rod. Fan blade, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Enginee-in-Charge. Make : Havells (model No ES - 40 )/Bajaj/Khetan / Orient

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 2 core, laid in trenches / duct / fixing on walls / poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing , incl dismantling of old unserviceable cable any size & type complete all as specified and directed.

M&L for HDPE Double Wall Corrugated pipe of size 32mm outer dia and 25mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. laid in trenches/ fixed to wall with suitable clamps for cable protection complete all as specified and directed. Make : Gemini/Stiple.

Cutting existing steel tubing of size 25/32mm bore for alterations or additions (each cut measured) done in position without taking down complete all as specified and as directed.

Screwing existing steel tubing for alterations or additions (or lenghtening screw on pipe to form connector) done in position without taking down complete all as specified and as directed.

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

M&L for Gun Metal gate valve with iron wheel head, screwed both ends for iron pipe of size 25mm dia complete all as specified.

M&L for valve chamber of size 600mm x 600mm x 900mm (internal dimentions) built in PCC M-10 grade (Nominal mix) using 40mm graded stone aggregate solid block masonary in CM 1:4 including lean concrete 100mm thick PCC M-7.5 grade (Nominal mix) using 40mm graded stone aggregate, plastering with CM 1:4, 15mm thick internally and externally including provision of 3.15mm thick MS sheet cover fixed with 50x50x6mm angle iron embeded in PCC M-15 grade (Nominal mix) using 40mm graded stone aggregate coping 100mm thick including painting to steel and iron work with two coats of synthetic enamel paint over a coat of red oxide primer and necessary earth work and excavation in any type of soil complete with locking arrangement lifting handles all as specified and directed.

Taking down the ceiling fan of any sweep carefully from its installed position, dismantling complete with down rod and replacement of capcitor, rubber wheel bush and cleaning of all dust, applying grease for bearings, reassembling the fan and blades, painting of fans and down rod with a coat of synthetic enamel white paint by spraying including filling cavities with filler, wiriting MES No with black paint, and keeping a site safely and hanging /refixing in positionafter false ceiling work or as directed and connecting up inclduding provision of 3 core twisted flexible copper condutor cable of 0.75 Sqmm from ceiling rose to connector of fan and testing on completion complete all as specified. Note :- (a) The spare parts Capacitor, Rubber wheel bush & Nut-bolts shall deemed to be included in the unit rate quoted. (b) Any damages/brocken of fans during the work, contractor will be responsible for the repair of the same or replaced with new without any extra cost.

M&L for sand cushioning to under ground cable in trenches in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. Note:- Measurement shall be taken after gentling puning.

Supplying and laying reinforced precast concrete cable cover class LV type 1 with flat size 250 mm x 150 mm x 40 mm complete all as directed.

S&F steel tubes light grade galvanised with all fittings fixed to walls/ floors/ poles/ road crossing etc of following sizes complete all as directed:-

50 mm bore

100 mm bore

Supplying, laying or fixing or passing through pipe, testing and commissioning XLPE insulated, steel tape/wire armoured heavy duty electric underground cable, 1100 volts grade with stranded aluminium conductor of following nominal cross sectional area :- Note :- Excavation and earthwork, PCC cable cover, sand cushioning etc shall be measured and paid separtely under relevant item of this BOQ.

10 sqmm 2 core.

16 sqmm 4 core.

25 sqmm 3.5 core.

70 sqmm 3.5 core.

150 sqmm 3.5 core.

240 sqmm 3.5 core.

M&L for Cable route indicator showing LT Cable and route/joint of cable with arrow made of CI in suitable eliptical shape and fixed on angle iron 40x40x6mm, 600mm long painted in Blue Colour with two coats of synthetic enamel paint cover a coat of red oxide primer duly embaded in PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate block 400x400x100mm in ground complete all as directed and specified.

Supply and fixing thermoplastic polystyrene/ polycarbonate enclosure busbar chambr three phase four wire of 100 amp rating of size 202 mm x 238 mm x 111 mm complete with shock proof, vermin proof and dust proof halogen and silicon free UV resistane with internally embedded gasket high grade gasket made of polyurethane complete with required terminals (1 row, 6 module) with one no. MCB SP 16 Amp including non metallic clamps and GI nut bolts and washers of suitable size and fixed on pole /wall complete all as specified and directed.

Supply & replacement PVC insulated and sheathed flat twin core solid aluminium conductor cable 1100 volts grade of size 2.50 sqmm complete all as directed.

Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 20mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost all as directed by Engr-in-Charge. (Note: GI strip beyond 5.0Mtr length from earth electrode shall be measured and paid separately).

S&F tripple pole and neutral, powder coated CRCA steel sheet MCCB distribution board constructed as per IS 8623 suitable for MCCB incomer upto 125 AMP, 4 ways, 415 volts, degree of protection IP 43 -IK *09 with metal door, recess mounted, having 200 Amp insulated tinned copper bus bar, neutral busbar earth bar din bar detachable glaned plates in unused spaces etc as required. Make :- Legrand cat part No 507745 or equivalent in L&T or PHL as approved

S&F MCCB four pole 125 Amps 16 KA thermally adjustable between 70 to 100% including 4 speader link set of same make as that of MCCB for connection, required luegs etc complete. Make :- Legrand Cat part no 420016 or equivalent in L&T or HPL as approved.

Dismantling stay assembly complete.

Dismantling ACSR conductors complete.

Dismantling Insulaotrs any type complete.

Dismantling of unserviceable cross arms/MS chanels, Angles

Ms Kamal Kant Agarwal