PROVN OF COVERED PARKING SHED WITH HARD STANDING NEAR NCC MESS OF HQ MB AREA, ADDN/ALTN OF KITCHEN/BAR/ANTE ROOM AND MISC WORK AT DSOI AND CERTAIN REV AND MINOR WORKS IN THE AOR OF AGE B/R-I UNDER GE (W) JABALPUR

Amount

Excavating in post holes (or similar holes) each n.exc 0.5 cu.m getting out, returning filling in and ramming earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft and loose soil complete all as specified and as directed.

M&L cement concrete type C-2 1:3:6 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L for hardcore of gauge n exe 63 mm ,deposited spread and levelled in layer n exc 100 mm thick , watered ,rolled to true surface complete all as specified and as directed.

S&F steel work in tubular trushes including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc complete all as specified and as directed

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J or L hook complete all as specified and as directed

Painting to new steel surfaces of any description, over 10cm width or girth applying two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified.

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and as directed.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

Machine pressed precast concrete inter locking paver block any shape and size made of M-40 grade concrete (with grey cement and no pigment) of 80mm thickness with 6mm top layer of anti abrasive material laid over 50 mm thick (compacted) fine sieved sand complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate in copings, kerbs, and the like all as directed incl necessary form work complete all as specified and as directed

M&L MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete all as specified and as directed

Excavation in trenches n. exc. 1.5 mtr wide and n exe 1.5m in depth for foundation and getting out in soft/ loose soil complete all as specified and as directed.

Returning filling in including, spreading, levelling, watering and well ramming in layer n. exc. 25 cm in soft/ loose soil complete all as specified and as directed.

Removing excavated material nexc 50 M and depositing where directed at a level nexc 1.5 M above the starting point complete all as specified and as directed.

M & L brick work with kiln burnt brick built in CM (1:6) using subclass ‘B’ brick straight or curved on plan exceeding 6 meter mean radius with old size bricks complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Fair Faces of Brick Walls or on Concrete Surfaces with WPC Finished fair and even complete all as specified and directed. Note: WPC shall be measured and paid separately.

M & L for preparation newly plastered surfaces & applying two coats of cement based paint over a coat of cement primer complete all as specified and as directed .

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness incl part chipping (below or above ground level) complete all as specified and directed.

Dismantling of wall tile, floor tile, dado including bedding but backing and rubbish off permises complete all as specified and directed.

Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc complete all as specified and directed.

M&L for non skid ceramic coloured joint free tiles 10 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38 sqm (600x600), in floors, set and jointed in neat cement slurry and pointed in white cement to over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for non skid ceramic coloured joint free tiles 10 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38 sqm (600x600), as in vertical surfaces such as skirting / dado set and jointed in neat cement slurry and pointed in white cement to over and including 10 mm thick backing in CM (1:4) complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate for insertion of hold fast incl necessary form work etc complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified and directed.

S&F in repair mild steel conduit curtain rod with PVC coating fancy type curten rod 20 mm dia of any colour including end globe as approved complete including side mounting complete all as specified and directed.

Taking down of eves gutter,rain water pipes ,AC/PVC pipes of any size or pattern including all fittings etc complete all as specified and directed.

S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F, in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed.

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe complete all as specified and directed

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper with 2mm thick wall care putty over a coat of chalk whitining on walls complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by complete removal of existing treatment and applying two coats of oil bound distemper over 2mm thick birla wall care putty over a coat of chalk whitining on walls complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed.

Complete removal of existing surface and applying exterior emulsion paint over a coat of Primer on old decorated surfaces incl preparation of surfaces complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in CM 1:6 for laying floor finish complete all as specified and all as direcred.

Dismantling of plain/ corrugated AC sheeting, any gauge, thickness, incl nainital or similar pattern roof covering complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding/ ridge to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Dismantling of timber scantlings unframed 40Sq Cm and over in section, in any position complete all as specified and directed.

M&L, Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates ,rails,braces etc complete drilled for fixing of steel gate sheeting or other covering,doors ,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering ,runing rails and guides ) and hanging also fastning and fixing complete all as specified and directed. confirming to FE-290 ( Gde E-165) complete all as specified and as directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed

M&L for RCC 1:1.5:3 using 20mm graded stone aggregate in lintel beams/roof beam cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed

M&L for TMT reinforcement bars 10mm over dia including all cutting bending binding cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and as directed

M&L for TMT reinforcement bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring, 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded including 20mm thick screed bed to floor finishes in cm 1:6 complete all as specified and directed.

S&F steel windows with side hung shutters factory made including box type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed or welded

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in a square n exc 0.5 Sq m in each pane complete all as specified and as directed.

S & F Steel window with side hung shutters incl projecting type hinges with steel handle , steel peg stay, complete without glazing bars cooler type window, dovetailed and welded.or ventilators, fixed type, complete all as specified and directed..

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick in cooking platforms incl edge moulding & cutting holes for gas pipe through drill machine and jointed with grey cement slurry and pointed to match the shade of granite stone including grinding and polishing fixed over and including screed bed 15 mm thick in CM 1 : 6 etc complete all as specified and as directed.

M&L for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded aggregate) including necessary form work complete all as specified and directed.

M&L Formwork to soffits of Suspended slab such as roof slab,floor slabs landing and similar work not exceeding 200 mm thickness as directed by Engr-in-Charge

Supply & Fixing 18 mm thick, PVC sheet one side prelaminated of approved texture ("Celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE ) as in Kitchen cabinet (withshelves and partitions) including necessary fitting & fixture as per manuacturer's instructions complete all as specified & directed.

M&L for Complete removal of existing water proofing treatment from roof and providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non approachable roofs- (i) Cleaning and sweeping and washing down with water to remove all dust etc from plastered roof surfaces / walls and filling of crack with sealing compound etc (ii) Bituminous based primer conforming to IS: 3384 – 1965 @ 0.3 Kg/Sqm (iii) One layer of super thermo APP modified water proofing memberane with non polyester reinforcement of any make.( M/s STP texsa ltd/Hyperplas memberane of M/S IWL India ltd/MS STPand Tikki Tar ltd). (iv) 3mm thick and minimum Weight @3.50Kg/Sqm,laid with gas torch and pasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surface after cutting necessary grooves and making good with PCC gola 1:2:4 type- B1 etc adhere to bitumen all as per manufactures instructions. (v) Applying two coat of aluminum paint @ 0.20 Kg / Sqm in two coats over bitumen layer as per manufacturer instruction . (application including sides lap,over laps shall be provided not less than 10 cm and joint sealed with torch as per manufactureerr's instructions specifications and as per particular specifications complete all as specified and directed.

M&L for 10mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3% by wight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and direcated (WPC shall be measured & paid seperately)

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) exc 1.5 Sqm but n.exc. 4 Sqm each complete all as specified and directed.

Taking down shutter of any description n exc 1 sqm each and removing to store complete all as specified and directed.

Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified and directed.

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed.

S & F 35 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats complete all as specified and directed.

S&F Plain, solid, straight IInd class HW chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed for door/window complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed.

S&F for aluminium anodised, barrel tower bolts of extruded section with length of bolt 100 mm and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised of size 100 mm complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Butt hinges 100mm, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F, Mild steel barrel tower bolts 150 mm size, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F, Mild steel pressed handles 150mm size, oval type, stove enamelled black complete all as specified and directed.

S&F, Mild steel sliding door bolts 300mm size, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F Butt hinges (ISI marked), medium weight, cold rolled mild steel of size 75 mm complete all as specified and directed.

S&F mild steel, 150 mm long ordinary helical door spring incl roller and roller plate complete all as specified and directed.

S&F Floor 40-50 mm door stopper of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete

S&F small fitings of 2nd class hard wood door, window stops and the like not exc 200 cucm each including MS butt hinges, medium weight, cold rolled 50mm long complete all as specified and directed.

S&F stainless steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F of aluminium powder coated section, as in frame for door, window, ventilators,fix glazing and partitions of standard section and thickness as directed , cut and jointed together with cadium plated steel screws, plugs for fixing screws, etc. complete all as specified and as directed by the Engineer-in-Charge. Note-(i) Fixing of frame shall be as per manufacturers instructions and all fitting shall be paid under this item. (ii) Thickness of powder coating shall not be less than 50 micron. (iii) Frame shall be one or more rebate as per requirement at site.

Supply and fixing for aluminium alloy (powder-coated) door shutters with hollow aluminium sections as specified including aluminium powder coated snap type beads, dish type door handles, glazed clip joint cleats, rubber gasket, Mortice lock 4 levers (vertical type), two numbers of aluminium alloy anodized tower bolts 200mm long to each leaf, etc. including fixing frame to wall/RCC members with rawl plugs complete. Sections of doors shall be aluminium hollow sections as follows : - (a) Shutter top 83.50mmx44.45mmx1.87mm thick. (b) Shutter bottom 104.00mmx44.45mmx 1.80mm thick (c) Shutter vertical 83.5mmx44.45mmx1.87mm thick (d) Shutter middle 100.00mmx 44.45mmx 2.00mm thick (e) Gauging clip weighing not less than 0.097kg/metre (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. 2. Glass pane shall be measured and paid separately.)

Supply and fixing for aluminium alloy powder-coate) window frame with shutters open able type, with aluminium sections as per of “Jindal” section numbers for casement windows including aluminium alloy snap type beads, handles, aluminium barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified for series-B “ Jindal” section numbers for casement (a) Section for shutter 47.62x44.45x1.87 mm thick (b) Glazing clip weighing 0.259kg/mtr. (c) Windows shall be provided with 02 Nos. of tower bolt of size 125mm for single leaf shutter and 03 Nos. for double leaf. Handles shall be aluminium ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and 01 No on each openable leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. 2.Glass pane and wire gauge shall be measured and paid for separately.

M & L for snap grid false ceiling system of E board exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), and fixed with pre painted 4mm thick E board of approved design and with provn of light fixture complete all as per manufacturer instructions and as directed.

M&L for cement concrete type D-2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed .

M&L for machine cut cudappa stone slab 20 to 25 mm thick over and including cement screed base 15mm thick in CM 1:6 in floors laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F vitreous China squatting pan of pattern Orissa Pattern , size 580 x440 mm white with P or S trap , front or backinlet and integral foot rests any pattertn (excl flushing cistern and flush pipe) complete incl provn of lime concrete bedding connection to flush pipe , trap etc & making good complete all as specified and directed (Make: PRAYAG / CERA/ Parryware)..

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 15mm dia, 450mm long etc complete all as specified and directed (Make: PRAYAG / CERA/ Parryware/Jaquar).

S&F 15mm dia pillar tap cast copper alloy chromium plated capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe complete all as specified and directed

S&F grating doom 100mm dia CP (Min weight 25 grms) complete all as specified and directed

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm,450x350 or 350x250 6 to 7mm thick on vertical surface such as skirting/dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed

Virified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in. through brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 15 mm dia bib taps cast copper alloy with Chromium plated cruch or butterfly handle scrwed, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm bore dia angular stop valves chromium plated fancy type, long shank, screwed down , high pressure ,screwed both ends for iron pipe or for union and fixed complete all as specified and directed .

S&F stop valves 15mm , cast copper alloy , fancy type chromium palted screwed down , high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F Towel rail 600 mm long and 20 mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats complete all as specified and directed.

S & F gate / globe valves 20 mm bore cast copper alloy screwed both end down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed bore of complete all as specified and directed.

Supply & fixed PVC connection 15 mm size , 450mm long with PTMT adopter,check nuts and washer on both sides complete all as specified and directed.

S&F as Ball valve PTMT 20 mm high pressure with epoxy coated, Aluminium rod & high density plastic ball screwed for iron pipe and fixed (minium wt 210 gm), complete all as specified and as directed.

S & F 32 mm thick PVC waste pipe of minimum length 1 mtr for kitchen sink and WHB etc complete all as specified and as directed.

S&F Flush pipes to WC including all joints and making good of all disturbed portion complete all as specified and directed

S&F jet spray with 1m PVC tube (stainless steel), chromium plated for vitreous china padestal pattern water closet complete all as specified and directed.

S&F chromium plated, Toilet paper holder complete all as specified and directed.

M & L for 100mm thick Cement concrete type B-2, 1:2:4, using 40mm graded stone aggregate in subbase complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 16mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 20mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 25mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement of 75mm dia complete all as specified and directed.

S&F Health faucet brass CP with 1.20M long PVC flexible pipe with Brass/CP check nut and bracket fixed to wall complete all as specified and directed.

S& F 500 ltrs rotational moulded polythine water storage tanks three layered white coloured (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves,high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule complete all as specified and directed.

Supply and fix figured glass ordinary quality 4mm thick in square not exc 0.50 Sqm each pane fixing in aluminium window complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC Sheet & edges will be painted to match with prelam sheet, reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F, Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing

S&F Aluminium anodised barrel tower bolts of extruded section 200mm long complete all as specified and as directed.

S&F aluminium alloy anodized sliding door bolt with hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 250mm complete all as specified and directed by Engr-in-charge.

M&L for Birck work with Fly ash, old size sub class 'B' bricks of compressive strength not less than 75 Kg/sqcm, straight or curved on plan exc 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for ENDURA out door tiles 30 cm x 30 cm x 10 mm thick rubberised mould set, jointed and pointed in neat cement slurry and pointed in white on coloured cement to match as in floors etc layed over and including screed bed or bedding layer of cement mortar 1:6, 15 mm thick etc all complete (Make-H & R Johnson, Brand-Endura designer digital series)

SS Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Supply & Fixed for ceramic wash hand counter top basin white colour of size 700X460mmX200mm quality make approved by GE complete all as specified and directed.

S&F for stainless steel chromium plated single lever basin mixermake approved by GE including all necessary fittings comlete all as specified and directed.

Supply & Fixed for Towel Ring complete all as specified and directed.

Supply and fixing Wall hung wc with UF soft close seat cover, hinges, accessories set, size 385 X 595 X 385mm including all fittings complete all as specified and directed.

Supply and fixing of single piece slim concealed flushing cistern with wall mounting frame , installation kit and "S-type drain pipe connection set for wall hung Wc including all fittings complete all as specified and directed.

Supply and fixing of flush control plate for concealed flushing cistern including all fittings complete all as specified and directed.

Supply and fixing of metropole flush valves dual flow 32mm size ( concealed body) with exposed shut off provision and 100mm square plate (3.0 / 6.0 ltr per flushing ) including control cock and operating lever including all fittings complete all as specified and directed.

S&F for looking mirror of size 5 feet X 3.5feet with designer glass and frame to be fitted with wall including all necessary arrangements and fittings complete all as specified and directed. Make: Saint Gobain or equivalent approved by GE.

S & F for Towel Rack 600mm long with lower hangers complete all as specified and directed.

Dismantling of wall and ceiling boards any type (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Virified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, as in vertical surfaces such as skirting / dado set and jointed in neat cement slurry and pointed in white cement to over and including 10 mm thick backing in CM (1:4) complete all as specified and directed.

M&L for Polishing the existing old kota stone flooring including preparation, grinding and polishing in floors complete all as specified and directed.

M&L 40 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

S & F Sheet glass 5.5 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F Mortice lock,vertical type size 100 mm 4 lever Make- Godrej as complete all as specified and directed

S&F Stainless Steel handles suitable for Aluminium powder coated door shutters not less than 300mm long design/Make as approved by GE (ISI Mark) complete all as specified and directed

S&F in repairs floor door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to aluminium door etc. complete all as specified and directed.

S&F in repair 50 mm Floor door stopper of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregates as in floors as sub base using extra cement in patches etc all as specified and directed by Engr-in-charge.

M&L for Brick work using old bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 etc complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick work or concrete surface of wall in CM 1:6 and to be finished even and smooth without using extra cement etc complete all as specified and directed

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, wind ties etc. conforming Fe 410 -W (GdeE- 250) qualityA complete all as specified and directed.

S&F 18mm thick ply, PVC sheet of approved texture ("Celuca Ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet and cupboard etc (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and directed.

S&F stainless steel kitchen basket in various type of basket , plaint basket height , 4" Thali basket 8" height Cup saucer 4" heigt and perforated cutlury basket 4" height all as specified and directed.

S&F hattich chennel for basket sizes 46mm wide complete all as specified and directed.

S&F stainless steel hinges for cupboards of senso (as per 3D designs) inclduding all connection fitting as complete all as specified and directed and approved by GE.

S&F handles of senso (as per 3D designs) 150 mm inclduding all connection fitting as complete all as specified and directed and approved by GE.

S & F of diamond cut square double bowl stainless steel kitchen sink made of stainless steel 2mm thick collar and 1mm thick bowl with plug washers, waste pipes, cast iron cantilever brackets, connecting union over all size 45"X20"X10" with bowl size 22"X16"X10", including bedding in cement mortar and connecting unions to pipe in repair complete all as directed (Make: Prayag/ Nirali/Jaquar or equivalent make approved by GE).

S&F for single lever sink mixer chromium plated including all fittings as per Cat No FLR-CHR-5165 Florentine of Make : Jaquar or equivalent complete all as specified and directed.

S&F in repair 15 mm dia bib taps cast copper alloy with Chromium plated cruch or butterfly handle scrwed, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs stop valves 15mm , cast copper alloy , fancy type chromium palted screwed down , high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F for steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F for steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F for steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying two coat of oil bound distemper over a coat of birla wall care putty over a coat of chalk whitining on walls complete all as specified and directed.

S & F in repair for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F in repair for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

M&L applying two coats of exterior emulsion paint over a coat of primer on old decorated surfaces incl preparation of surfaces complete all as specified and directed.

M&L for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and as directed

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in a square n exc 0.5 Sq m in each pane complete all as specified and as directed.

M & L Machine pressed coloured precast concrete rubbber moulded interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and as directed.

M & L for 50 mm thick Sand filling below the interlocking paver block including watering and consolidation complete all as specified and as directed

Painting to new steel surfaces of any description, over not exceed 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified.

M&L for 150mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate), using 40 mm graded stone aggregate as in flooring complete all as specified and as directed.

S&F Expanded metal not exc 4 kg/Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Taking down carefully any type of old unserviceable point wiring (light, fan, socket bell or power) , complete with fittings such as switches ceiling roses, lamp holders sockets, regulators with PVC conduit surface /concealed or wooden patterns including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

Taking down carefully Main switch and Distribution boards any make and size complete all as specified and as directed .

Taking down the ceiling fan in situ and refixing after servicing, repairing and painting to ceiling fan including scratching old paint and preparation of surface for painting with one coat of white/grey enameled paint complete all as specified and directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

M/L for Sub Main Wiring with two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 4.00 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two Nos of 4.00 Sqmm Wire and One No of 4.00 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor FRLSH cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of anticorrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white Bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor FRLSH cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed.

(a) One light point/fan point/bell point controlled by one switch.

(b) One socket point controlled by one switch on same board.

(c) One socket point controlled by one switch on Independent board.

All as described in serial item No. 183 here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

S&F for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and as directed .

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F Ceiling rose surface bakelite 65 mm x 50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 20 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

Supply & fix in replacement of LED Security Light Luminaire 25 watt with 2500 or more lumen warm white, surge protection device upto 4KV, IP65 or more, IK07 or more, potted driver suitable for 180 to 270 V, 50 Hz, light engine driver base.pole adapter, powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make: Philips cat part no: BRP029 LED25/WW MRPSU GR DX or havells cat part no. ENDURASUNDOWNSL25WLED765PASYBOPCIHD or equivalent in wipro/GE

Supply & Fixing Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1/Havells /Crompton

S & F in repair of LED Decorative /mirror light fitting 9 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent in PHILIPS ,BAJAJ

S&F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed. Make :Havells Cat Part No.HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make: PHILIPS /Havells/wipro

Supply & fixing, in replacement, Kit kat DB by SPN Distribution box double door, protection grade IP 43, in fine powder coated matt finish with best CRCA sheet fitted with shrouded neutral insulated pin type copper bus bar Din rail earth bar, 8 way conforming to IS 13032 & 8623 complete all as specified and directed ( Make : Legrand CAT NO 507621 / SIEMENS / Schneider (Electric) as approved by GE)

S&F in replacement of sheet metal enclouser distribution boards, double door factory made 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 63 amps , circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.Make of Distribution Board Legrand cat no:5077 50 or equivalent in seimens /GE and Make of MCBs :Legrand/Seimens/GE

S&F in replacement of sheet steel enclouser distribution boards, double door factory made VTPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 160 amps and MCB TP 100 A -02 Nos,MCB SP 32 -08 Nos circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.Make of Distribution Board Legrand cat no:5077 50 or equivalent in seimens /GE and Make of MCBs :Legrand/Seimens/GE

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge Make : Havells/ CG/ Bajaj

S & F MCB TPN 25 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 4 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand /Seimens/GE

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand CAT NO 507611 / SIEMENS CAT NO 8 GB 32102RC8/GE/ABB

Supply and fixing MCB single pole and neutral 240 volts 20 Amps, B Series complete all as specified and directed by Engineer in charge.

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand DX3 DP CAT No 408637/ Siemens cat no- 5SL 42327RC / GE

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. Make:- Legrand/ ABB/GE

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand cat no DX3 SP 408587,408590,408592,408593,408594,408595 / Siemens cat no- 5SL41067RC, 5SL41107RC, 5SL41167RC, 5SL41207RC, 5SL41257RC, 5SL41327RC / GE

Supply, laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 6 Sqmm complete all as specified and directed.

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3.5 core all as per required and directed.

S & F in repair fan regulator Step type of polycarbonate complete all as specified and directed by Engineer in charge.

Supply anf fixing in repair of LED lamp rotary type/holder type of 12 watt all as specified and directed by engr-in-charge.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

S & F Exhaust fan heavy duty plastic body of size sweep 230 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed by Engineer in-charge.Make- Bajaj/ Havells/Usha

S&F LED light fitting square 2'x2' CM 30watt, 3000 lumen, Warm white 5700K, THD max 10 % ,CRI min 80 % warm white along with fixture Surface / Recessed /Pendent mounting LED luminaries with diffuser channel Luminaires ers, connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. Make: Philips cat part no: RC380BLED30S-5700 G6L60W60 PSU OD or equiv in GE/Osram/Wipro.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

M & L for DWCP pipe 50 mm OD and 38 mm ID for cable protection with all acesseries all as per required and directed by Enggr in charge

Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. all as specified and directed by Engr in Charge.of size 50 mm outer dia and 38 mm inner dia of Make;-Telerex/Tirupati or E-in-C approved Make

Supply and lay DWCP pipe OD 65 mm , ID 38 mm all as per required and directed by Engg I charge(Necessary excavtion may please be added in rate quoted)

DEEPAK CONSTRUCTION

ANAMIKA CONSTRUCTION

a k builders

M/S Modern builders