SPECIAL REPAIRS TO BLDG NO T 55 AT MW LINE OF 512 ABW PROVN OF CHAIN LINK FENCING WITH BARBEDWIRE AROUND THE BLDG NO P 33 TO P 38 AT ENGINE HOUSE ROAD UNDER GE C KIRKEE.

Amount

B/R WORKS

Taking down chowkats and frame area n.exc 1.5 Sq.mm each including shutters without taking off shutters from the frame and removing from site complete all as specified and as directed

Taking down chowkats and frame area exc 1.5 Sq.mm but n.exc 4.00 Sq.mm each including shutter with out taking off shutter from the frame and removing from site. complete all as specified and as directed.

Taking down shutters of any description area exc. 1.00 Sq.mm but n.exc 2.00 Sq.mm each resecuring, easing , adjusting and re-fixing in same opening after minor repairs like changing of Butt Hings and including all necessary fittings complete all as specified and as directed

Taking down shutter of any description area n.exc 1 Sq.mm each and removing to store complete all as specified and as directed.

Pressed steel door frame for doors of size 105 x 60mm with single rebate including necessary fixing lugs, hinges, lock strike plate, etc complete including and of hollow section of frame with and including PCC 1:2:4 type B-0 complete all as specified and as directed.

Pressed steel frames made of 1.25 mm thick MS Sheet size 125x60mm for doors, ventilator with double rebates including necessary fixing lugs, hinges, lock strike plate etc, M & L for providing PCC 1:2:4 type B1 (using 20mm graded stone agg) to fill the frame & making good complete all as specified and as directed .

35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat omplete all as specified and as directed.

35 mm thick 2nd class hard wood glazed/gauzed and skeleton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed.

Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixing in wooden or steel door frame using nails or welding complete fixed in repairs all as specified and as directed.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete fixed in repairs all as specified and as directed.

25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides both face shall be covered with decorative face veneers with lipping / frame to match as in cupboard door shutters complete all as specified and as directed.

18-19mm thick prelaminated particle board pre-laminated both side, grade 2 quality, interior grade, commercial type including 6 mm thick teak wood lipping, as shelf in cupboards, kitchen cabinet, pelment box and in similar works complete all as specified and as directed.

Continuous (Piano) hinges, mild steel, bright finish or electro galvanised Width of flaps (when open) in 40mm Complete all as specified and as directed.

100mm hasp and staple, safety type, Aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

100mm long stainless steel medium weight butt hinges for door shutter and frames / welded to frames complete all as specified and as directed.

200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

150mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

300mm long mild steel sliding door bolts, bolt or clip type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

150 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in repairs as in floors complete all as specified and as directed.

Factory made internal PVC door frame of size 50x47mm single riveted, made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and directed.

Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawings.

75mm long stainless steel medium weight but hinges for door shutter and frames complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed.

Aluminium anodised handle, oval type, of size 150mm, fixed with screws or welded, complete all as specified and as directed.

Aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.36mm dia apperture 1.4mm SS wire mesh and fittings etc and making good the jambs and painting with existing surface to match complete all as specified and as directed

Machine cut cudappa stone slab 20-25mm thick as in steps, jambs, pillars, cooking platforms and like over 15mm thick cement screed base in CM (1:4) and jointed in grey cement slurry mixed with pigment to match with shade of slab rubbing, polishing and rounding to edges includimg demolition of existing cill / cooking platform complete all as specified and as directed.

Aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. making good the jambs and painting with existing surface to match complete all as specified and as directed

Rolled mild steel as in frame work such as grill, grating etc with ends bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed.

Preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primere complete all as specified and as directed

Preparation of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamal paint complete all as specified and as directed.

Preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Preparing old wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Demolition of existing lime concrete of any description and in any position not otherwise specifically provided for, incl removing of debries complete all as specified and as directed.

Plain cement concrete, (1:5:10), type E2 using 40 mm graded stone aggregate as in foundation filling and mass concrete as in sub base of floor complete all as specified and as directed.

Water proofing treatment to the sunken portion areas as under :- (a) Preparation of sunken surfaces of wall or concrete and providing 10 mm thick rendering in cement mortar (1:3) mixed with WPC @ 3 % by weight of cement and applying evenly a coat of blown bitumen at the rate of 1.5 kg per square metre and binding with clean dry sand @0.005 cu.m per Square metre complete all as specified and as directed (b)GI pipe 40m bore light grade shall be embedded as outlet at the lowest portion for slope on the wall extending upto at least 450 mm beyond the outer wall. Note :- Rate for WPC is deemed to be included in the quoted rate.

Removing old tar felt, all loose dirt, old roof tiles, including taking down cement plaster, cleaning the concrete surface including removal & cleaning of vegetation, fungus, moss small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work and applying neat cement slurry @ 1.5Kg/Sqm complete all as specified and as directed.

Rendering 15mm thick on existing concrete surfaces of roof in CM (1:4) mixed with water proofing compound @ 3% by weight of cement finishing even and smooth without using extra cement for water proofing treatment over RCC slab by applying oil bound bitumen primer @ 0.25 kg/Sqm and providing and laying 3 mm thick APP modified water proofing memberane of IWLor techno commrcially equivalent weighing not less than 3.00 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having softening point not less than 1500C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing streangth of 180 N / 5 cm, torch application, with a overlap of 100mm at the sides and 150mm at the ends, sealing and applying a coat of solar reflective aluminium paint @ 0.11 Kg/Sqm on membrane surfaces complete including carrying out 24 hrs ponding test over the complete treatment complete all as specified and as directed . Note : Rate for WPC shall be deemed to be included in the quoted rate.

Taking down cement of cement lime plaster of any description at any position on brick or stone or PCC block walls, chajja etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed

Rendering 12mm thick on fair faces of brick /stone or concrete surfaces of wall in (CM 1:6) complete all as specified and as directed.

20mm thick cemet plalster in (CM 1:4)over stone wall / concrete surfaces finished even and Fair without using extra cement complete all as specified and as directed.

5mm thick rendering on concrete surface/Chajja of ceiling in (CM 1:3) and rendering is to be finished even and smooth with out using extra cement complete all as specified and as directed.

Demolition of brick /stone walls built in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in (CM 1:6) complete all as specified and as directed.

Pre cast cement concrete solid block masonry with solid block of the grade C1 (1:3:6) set in CM (1:6) complete all as specified and as directed.

Preparation of new plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and as directed.

Preparation of new plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and as directed.

Preparation of new plastered wall surfaces and applying two coats of white wash on newly plastered surfaces of walls complete all as specified and as directed.

Preparation of old plastered wall surfaces and applying two coats of white wash on newly plastered surfaces of walls complete all as specified and as directed.

Preparation of old decorated plastered or unplastered surfaces of wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots and applying two coat of cement base paint (white or tinned) complete all as specified and directed.

Preparation of new decorated plastered or unplastered surfaces of wall, and applying two coats of cement base paint (white or tinned) over a coats of alkali reistant primer complete all as specified and directed.

Preparation of new plastered ceiling surfaces and applying two coats of white wash on newly plastered surfaces of walls complete all as specified and as directed.

Preparation of old plastered ceiling surfaces and applying one coat of white wash on newly plastered surfaces of walls complete all as specified and as directed.

Plain Cement Concrete, type B-1, (1:2:4) using 20mm graded aggregate as in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and as directed.

Dismantling existing tanks, exc. 250 ltr and n.exc. 500 ltr removing to store complete all as specified and as directed.

Rotational moulded polyethylene water storage tank consisting of three laver cylindrical vertical with top closed hoisted and fixed in position all as specified and directed capacity 500 ltrs complete all as specified and as directed .

20 mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete all as specified and as directed.

20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

Taking up or down existing steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and directed for 15mm bore complete all as specified and as directed.

Taking up or down existing steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and directed for 20mm bore complete all as specified and as directed.

15mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor complete all as specified and as directed .

20mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor complete all as specified and as directed .

Refixing 15mm bore old steel water tubing and connection in new or old position (walls, ceilling, floor etc) complete all as specified and as directed.

Refixing 20mm bore old steel water tubing and connection in new or old position (walls, ceilling, floor etc) complete all as specified and as directed .

Bib taps long body cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe all as per Prayag Cat Part No :8308 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe all as per Prayag Cat Part No :8310 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipes 15mm bore dia all as per Prayag Cat Part No :8304 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Stop cock (concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed both end for iron pipe or brass ferrule with long shank and cup for 15 mm bore of pipe complete all as per Prayag Cat Part No :8318/8320 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Brass chromium plated shower rose 225mm round with arm and flange including fixing to steel pipe fixed in repairs all as per Prayag Cat Part No : BS-67 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed.

Viterious china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but incl necessary brackets CP wastes and other fittings complete all as specified and as directed

Vitreous china squatting pan "Orissa" pattern of size 580mmx440mm white with integral foot rests including 10ltrs capacity PVC flushing cistern low levl with inlet, ball valve float chain and pull, brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern complete fixed in repairs all as specified and as directed.

Kitchen sink with drain board overall size 915x460mm, bowl size 410x330x160mm made out of stainless steel 1mm thick kitchen or laboratary sink with plugs, washers and waste including bedding in mortar on to dwarf wall, fixing cantilever brackets and connecting union pipes complete in repairs including taking down the existing sink complete all as specified and as directed.

32 mm bore PVC waste pipe of approved make suitable for WHB, urinals etc complete all as specified and as directed.

Grating doom 125 mm dia with/without waste hole of stainless steel complete all as specified and as directed.

PVC floor trap, square type with CP grating with or with out hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete fixed in repairs all as specified and as directed.

PVC connections 15mm dia with brass nut on both ends and washers 450mm long complete fixed in repairs all as specified and as directed.

Towel rail 450 mm long of PTMT fixed with and including chromium plated brass screw and wooden / plastics cleats ( min wt 170 gms) complete fixed in repairs all as specified and as directed.

110 mm dia PVC (SWR) pipe, type 'B' single socketed in any length with rubber ring joints laid in trenches,floor and wall including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches or in floors and wall 75mm bore including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

110mm dia (bore of pipe) PVC bends, type 'B' (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified and as directed.

PVC (SWR) bends, type 'B' 75mm dia bore any radius with access door complete fixed in repairs all as specified and as directed.

PVC (SWR) branch piece, type 'B' single (single Y) 110 mm dia equal or unequal complete fixed in repairs all as specified and as directed.

PVC (SWR) branch piece, type 'B' single (single Y) 75mm dia equal or unequal complete all as specified and as directed

75mm bore PVC (SWR) junction single (Single T) equal or unequal.type 'B' complete fixed in repairs all as specified and as directed.

110mm bore PVC (SWR) junction single (Single T) equal or unequal.type 'B' complete fixed in repairs all as specified and as directed.

110mm bore PVC (SWR) type 'B' vent cowl complete fixed in repairs all as specified and as directed.

75mm bore PVC (SWR) vent cowl, type 'B' complete fixed in repairs all as specified and as directed.

Dismantling floor hearth or wall tilling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate as in leveling course including demolition of existing PCC complete all as specified and as directed.

Screed bed or bedding layer of mortar 15 mm thick average thickness for laying floor finishes in cement mortar (1:4), complete all as specified and as directed.

Non skid ceramic coloured tiles, joint free 7 to 8 mm thick (square or rectangular) area of each tile exe 0.18 Sqm but n.exe 0.38 Sqm, laid in floors set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

Non skid ceramic coloured tiles,joint free 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm (400 x400x7mm) as in skirting, over 10mm thick backing coat in CM (1:4) on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and as directed.

Non skid coloured ceramic tiles 300 mm x 300 mm x 6 to 7mm thick, in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Glazed ceramic colour tiles in vertifical surface 450x350x7mm thick with necessary border etc set and jointed in neat cement slurry and pointed in coloured cement to match over including 10mm thick back coat in cement mortar (1:4) all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed.

Machine cut mirror polished Kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners, rubbing and mirror polishing complete all as specified and as directed.

Machine cut mirror polish Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners ,rubbing and mirror polishing complete as specified and as directed.

Repairs Stainless steel fancy type curain rod 25 mm including SS brackets, decorative knobs,and including all necessary fittings such as rawl plug screws complete all as specified and as directed.

Repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and as directed.

Repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in paving/ plinth protection laid in panels with necessary form work, finished rough surfaces of concrete including provision of construction joints complete all as specified and as directed.

Plain Cement concrete (1:4:8), type D2, using 40mm graded stone aggregate as in sub bases of floors, 100mm thick, complete all as specified and as directed.

25mm thick crushed stone dust/sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

80mm thick machine pressed glossy finish precast concrete interlocking paver block any shape and size & Colour M-40 grade with grey cement no pigment confirming to IS 15658-2006 complete all as specified and as directed.

Excavating in post holes (or similar holes) in soft loose soil each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregates) as in foundations,filling and mass concrete etc.complete all as specified & directed.

Rolled mild steel as in posts and struts, angle iron in fencing including cutting tops to shape as directed drilling holes notching for wire etc & flat iron fillets (for securring wire mesh etc) including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Rolled mild steel screw bolts machine made with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut length of bolt exc. 5cm but n.exc. 5cm long and dia of the neck 11 to 15 mm dia complete all as specified and as directed..

Fixing only chain link fencing including line wires any mesh size and type to any type of standards rails straining bolts etc including provision of binding wire complete all as specified and as directed.

Supply only chain link MS galvanised fencing any size or type complete all as specified and as directed..

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe 290 Gde E-165 complete all as specificed and as directed.

Glavanised 2 strand, steel barbed wire 2.24 mm dia, barbed with 2.00 mm dia barbs at 75 mm spacing, straining and fixing to any of standard rails and straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc complete all as specified and as directed.

Concertina coil made to shape as dia exc, 450 mm but not exc.600 mm put on top of wall in between 'Y' shape angle iron post and secured with necessary binding wire complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth and not n.exc 10 sqm on plan getting out in any type of soil complete all as specified and directed.

Plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregates) as in foundations,filling and mass concrete etc.complete all as specified & directed.

Reinforced cement concrete, M-25(Design mix) as in foundation for footings complete all as specified and as directed.

Reinforced cement concrete, M-25(Design mix) as column ,pillars ,piers,posts and struts etc. complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm thick using soft / disintegrated rock complete all specified and as directed.

Removing excavated surplus soil to a distance not exc 50 m and depositing where directed at level n.exc. 1.5 m above the starting point complete all as specified and as directed.

Steel form work to side of concrete foundation footing base of column and raft beams sides and soffits of plinth beams complete all as specified and directed.

Steelm form work to side of pillars,posts ,struts, pier, columns square ,rectangular or polygonal rough finished surface of concrete complete all as specified and as directed.

TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe 290 Gde E-165 complete all as specificed and as directed.

TMT steel bars 5mm dia and over, stirrups bending spirally for hooping for columns, hooking ends and binding with mild steel wire not less than 0.9mm dia complete all as specified and directed.

Rolled mild steel framed work such as steel doors,gates or other section or angle ,Fe-410-W Gde E-250 of quality ''A'' complete all as specified and directed.

Granite work in steps, jambs, pillars, window-cills,cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.with plastering 10mm thick in CM(1:4) on fair face of brick work or concrete surfaces finished even and rough to receive the tiles complete all as specified and directed.

E/M WORKS

Taking down copper/aluminium point wiring ( light, fan, socket, power ) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surface of walls, floors, etc

Point wiring with 1.5 sq.mm size PVC insulated unsheathed 1100 volt grade single core stranded FRLS (multithreaded) copper conductor cable drawn into and including PVC casing caping of suitable size with all fitting and accessories with sunk type pressed steel terminal/PVC surface type boxes of 1.6 mm with 3 mm thick laminated sheet top cover concealed/surface in walls complete for Provn of switches/socket/fan regulators including one continuous run of PVC insulated (green colour) 1.5 sq.mm multi stranded FRLSH copper conductor cable as earth wire and connected to common earth dolly for the following:- a) One light point controlled by one switch

b) One light point controlled by two 2-way switch

c) One fan point controlled by one switch

d) One three pin 5 Amp socket outlet with cables 1.5 sqmm on independent board.

e) One three pin 5 Amp socket with cables 1.5 sq mm on same board

f) One bell point controlled by one switch

All as per item No 2.002 above but with 2.5 sq.mm cable insulated for 3 pin 15 Amp multipin socket outlet including 2.5 sq.mm PVC insulated copper wire for earth continuity on independent board complete all as specified and as directed.

Sub main wiring with 2 x 4 sq.mm and 1x2.5 sq.mm earth wire drawn in PVC casing caping of suitable size with accessories .Note :-(i) Two runs of cable and one run of earth wire & casing caping shall be measured and paid as one unit (RM).

Stepped type electronic fan regulator for ceiling fans including necessary connections of capacity 100 watts. 240 Volt complete all as specified and as directed.

Switch Piano, flush type, 5 Amps, 240 Volts single pole, one way with ISI marked complete all as specified and as directed.

Switch Piano, flush type, 5 Amps, 240 Volts single pole, two way with ISI marked complete all as specified and as directed.

Socket outlet of 2 in 1 , 3 pin 5 amp complete all as specified and as directed.

Socket combination multipurpose outlet comprising of 3 pin 15 Amps socket out let & switch one pin, 5 Amp controlled by one switch suitable for 3 pin plug top complete all as specified and as directed.

Ceiling rose surface PVC 65 x 50 mm two/three terminals complete all as specified and as directed.

Call bell electric, ding dong, AC 240 volt, 50 HZ. including taking down unserviceable one complete all as specified and as directed.

Sheet metal enclosure for DBs SPN 8 Way double door type 230 Volts fixed in repairs complete all as specified and as directed.

MCB, Single Pole, 6 to 32 Amps, 240 Volts, 10 KA breaking cap, ‘’C” curve fixed in repairs complete all as specified and as directed.

MCB, SPN 40 Amps, 240 Volts, 10 KA breaking cap, ‘’C” curve fixed in repairs complete all as specified and as directed.

LED fitting, 20 watt, CDL, 230 Volts, 4 feet long, complete with all accessories internally pre wired and including connecting up to ceiling rose with 0.5 sq.mm twin core copper flexible conductor cable including LED lamp and mounting casing box 2 nos complete all as as per CG Cat Part No LCTLN-20-CDL or techno commercially equivalent in Bajaj/Philips/Havells

Lamp Holder insulated body with back plate for batten/angle complete all as specified and as directed.

LED Lamp 9 watt (B-22) pin type complete all as specified and as directed Make :- CG/Bajaj/ Philips/Wipro

LED type Bldg light fitting 15 Watt with cast aluminium with necessary brackets and clamps nut bolts etc complete all as specified and as directed Make : Bajaj/ CG/Philips/Wipro

MCB DB double door ETPN 4 way with 200 Amps rated bus bar 240 volts complete all as specified and as directed.

MCB TPN 40 Amps, 415 volt 10 KA complete all as specified and as directed.

REPAIR TO CEILING FANS WITH FOLLOWING ITEMS OF WORK :- Rewinding of ceiling fan 1200/1400 mm sweep after dismantling complete motor assy, bearings, bushings, removal of burnt copper wire, cleaning of core, inserting proper insulating paper in slots, winding with and as per existing size/turn of super enamelled copper wire, heating, varnishing, replacement of unsv bearings / bushings, assemble of rotor and stator unit with capacitor, connecting wire, down rod, blades and testing complete. Note: 1. Contractor shall collect fans from the complaint cells of specified area and bring back to complaint cell after repairs, cost of transportation will be inclusive of quoted rate. 2. Spares required for replacement such as bearing, bushing, capacitor shall be measured and paid separately as supply and fix only. 3. Cost of Connector block and capacitor holder shall be inclusive of the quoted rate.

Ball bearing No 6201/6202/6203/6204 of SKF/Tata/NBC as specified and as directed.

Gun metal bush bearing for ceiling fan as per existing pattern as specified and as directed.

Capacitor AC for 230 volts 50 Hz of capacity 2.0/2.25/2.5 Mfd as specified and as directed.

Painting of ceiling fan 1200/1400 mm including scrapping, cleaning and removing dust from the blade and body and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and as directed.

Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion.

ShreHari Civil Enginneering and Contractors

Shri Sant Cosntruction

DARSHAN ENTERPRISES