WBPHED/69_03/EE/BOLMD/24-25

Amount

Supply and delivery at site of vertical submersible pumping machinery directly coupled with wet winding type suitable size submersible motor with following specification: Discharge (Q) : 16 mᶟ/Hr. Head (H) : 75 mtrs. Method of starting : DOL Shaft-stainless steel, Impeller- Crome Steel / Noyrl, Outlet - 65/80 mm dia Motor : Operating Voltage : 415 (± 10 %), Phase : 3ph, 50 Hz ± 6% Speed : 2900 RPM, Method of starting : DOL Make : KSB / Texmo / CRI / KBL / MBH / or any approved vendor. (N.B : Manufacturer's test certificate along with charecteristics curve and gurantee certyificate have to be submitted at the time of delivery.)

Supply delivery at site of 4 sqmm 3 core 1.1 KV Grade flat submersible copper conductor cable . (Make:- Finolex / Gloster / Polycab / Mescab / or any Approved Vendor list of PHED.)

Supply & delivery at site of 10 mm² x 3 core Aluminum Armored, XLPE insulated 1.1 K.V. grade cable, conforming to IS 7098(I) as per direction of EIC. (Make:- Gloster / Polycab / Mescab / or any Approved Vendor list of PHED.)

Supply and delivery of the following valves, pipes and gauges etc at site-- (Make: Approved Vendor list of PHED.)

3mtr long 80mm dia UPVC standard type column pipe [cream color] with both side threaded and one end side socketed with registered KPMG.

1.5 mtr long 80mm dia UPVC standard type column pipe [cream color] with both side threaded and one end side socketed with registered KPMG.

80mm dia. CI Top & Bottom adopter.

Heavy type suitable dia. MS suspension clamp along with nuts bolts and washers.

80mm dia. CIDF Non-Raising Sluice Valves, PN 1.0 rating (Conforming to IS:14846) for wash out line. (MOC & TC needed for valve).

80mm dia. CIDF single door swing Non Return Valve, PN 1.0 rating (Conforming to IS:5312) (MOC & TC needed for valve).

CIDF 90°bend- 1no., CI flanged tee- 1no., blank flange-1no., CI/ MS flanged short piece 0.50 mtr.-1no, CI/ MS flanged pipe 1mtr.- 1 no. etc (as per IS specification and certification registered) for construction of delivery pipe line and wash out line.

Heavy type 250mm dia./suitable Split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design.

Anti snapping safety device for pump set by supplying suitable size of MS angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials.

Suitable Kiosk box for cable connection of submersible pump motor set with degree of protection IP 65 including suitable legs and 3 Nos. Al. Bus bar for 32 Amps and all necessary earthing arrangement and insulator as per direction of EIC.

Making brick pillar 0.25 x 0.25 x 0.75 Mtr/Suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete. (Both Pipe line)

Making CC foundation for support of the kiosk box after excavating the earth upto a depth of 0.6 Mtr below the GL including supply of all materials complete with 12 mm thick cement plastering with net cement finishing complete as per direction of EIC (size: 3' x 1' x 5')

Supply & Making necessary GI Medium pipe (dia of pipe not less than 32mm) protection for submersible cable from kiox box to submersible pump-motor set including supply of all specials and complete the job. (For Road Crossing, if necessary)

Incresseing the existing tube well Casing height up to a standard level as per direction of EIC. Dia upto of 250 mm.

Laying of two cables upto 35 sqmm in an underground trench in single tier formation (horizontal), the trench size of 680mm x 760mm average depth, with brick protection on the top of each cable 8 (eight) Nos. bricks per Mtr. and 4 (four) Nos. bricks per Mtr. as separator between the bricks and cables and also trench to be filled up with shifted soil, levelling up and restoring surface duly rammed.

Installation of Submersible pumping machinery to newly sunk tubewell along with column pipes (as required), top cover, valves, and specials of above with protection pipe and supply of MS clamp, nut bolt, cable gland socket etc. making inerconnection of the pump delivery line to pump collecting main line near tubewell with supply of all necceasary pipe, reducer/enlarger, GI/MS specials etc. including brick, sand, cement, rod etc and laying & drawing of all actuator cable & cable protection pipe as required and all to complete the job including all connection & testing commissioning as per direction of EIC.

Withdrawing of 1 Nos. Submersible pumping machinery (5HP) along with all M.S column pipe by own arrangement including disconnection of power line & delivery line all complete .

Lowering the 1No. 7.5HP Submersible pumping machinery (New) along with M.S. column pipe by own arrangement making power line & delivery line connection all complete.

Add: GST @ 18% on sum of Item No: 1 to 18

Add: Cess @1% on sum of Item No. 19

SUNIL RABIDAS (BID ID -6180119)

OSMAN SEKH (BID ID -6179057)