PROVN OF 01 X SHELTER WITH 02 X PARTITIONS (10 FT X 15 FT AND 5 FT X 10 FT) 01 X CHEMICAL EARTHING AND ADEQUATE LIGHT POINTS NEAR BLDG NO T 244 AT ZAKHAMA MIL STN

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed.

Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and as directed.

Excavation in trenches n. exc 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, of soil including spreading leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed .

Removing excavated material to a distance n.exc 50M and deposited/ spreaded where directed at a level n. exc 1.5 M above the starting point complete all as specified and as directed .

Excavation in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance n.exc 50m and making good disturbed surface in soft/loose soil complete all as specified and as directed.

Materials and labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Material and labour for hardcore of broken stone or boulders of gauge n.exc 63mm, deposited, spread and leveled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for PCC (1:2:4), type B0, (using 12.50mm graded stone aggregate), as in coping, haunching including weathering, slightly rounded or chamfered angles and throating, including necessary formwork complete all as specified and as directed

Material and labour for forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade-A complete all as specified and as directed.

Material and labour for precast cement concrete (1:3:6) type C1, (using 20mm graded stone aggregate) as in kerb stone/bond stone including necessary form work set in cement mortar(1:4) complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) (nominal mix ) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note- Reinforcement shall be measured and paid seperately under respective items.

Material and labour for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) (nominal mix ) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. Note- Reinforcement shall be measured and paid seperately under respective items.

Material and labour for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) (nominal mix ) as in chajjas complete all as specified and as directed. Note- Reinforcement shall be measured and paid seperately under respective items.

Material and labour for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, paving, footpath etc and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 100mm thick, PCC (1:4:8), type D2, (using 40mm graded aggregate) as in sub base of floor and finished the surface fair and even complete all as specified and as directed.

Material and labour for 40mm thick, PCC (1:2:4), type B0, (using 12.50mm graded aggregate) as in base of floor and finished the surface fair and even complete all as specified and as directed.

Supply only integral water proofing compound (WPC) of best quality complete all as specified and as directed.

Material and labour for hand packing (any thickness) of broken stone or boulder at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed.

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Materials and labour for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and as directed.

Materials and labour for use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished flat surfaces of concrete complete all as specified and as directed.

Materials and labour for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) with rough finished flat surfaces of concrete complete all as specified and as directed.

Materials and labour for use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and as directed.

Supply and fixing well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

Supply and fixing for 35mm thick factory made second class hardwood rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and fixing 125mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21complete all as specified and as directed.

Supply and fixing aluminium anodized, barrel tower bolts, 150mm long of extruded section complete all as specified and as directed.

Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and as directed.

Supply and fixing 200mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing of chimney bars (straight or camber); bearing bars; tongues or water bars for window frames, window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fixing steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, glazing bar dovetailed or welded for receiving glass complete all as specified and as directed.

Supply and fixing steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified and as directed.

Supply and fixing Rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe-410W (Gde-E-250) Quality-A complete all as specified and as directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars 6 to 8mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars 5mm dia and over and upto and including 10mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for stirrups, spacers, binders and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed.

Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed.

Supply and fixing Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed.

Supply and fixing hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed.

Supply and fixing 6mm thick veneered decorative ply wood (5 No of ply), grade I (with BWR resin) decorative veneers on both faces complete all as specified and as directed.

Material and labour for vitrified ceramic tiles (dark shade) 10mm thick (Square/rectangular) area of each tile n.exc 0.36 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour for raised pointing to random rubble or polygonal rubble, uncoursed or brought upto courses wall in cement mortar (1:4) complete all as specified and as directed.

Materials and labour for 5 mm thick rendering on concrete surface in cement mortar (1:3) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

Materials and labour for 20 mm thick rendering on fair faces of brick work in two layers, first layer of 10mm thick without water proofing compound and top layer of 10mm thick with using water proofing coumpound in cement mortar (1:4) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. Note : WPC will be measured and paid separately under respective item.

Materials and labour for 15 mm thick rendering on fair faces of brick work surfaces in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

Material and labour for applying two coats of cement base paint over a coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and as directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for preparing surfaces of wood and wood based materials, treating ends of posts, back of chowkats etc. area tarred exc 0.1 sqm but n.exc 0.5 sqm each and treated with one coat of tar or coal tar black paint complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Supply and fixing 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane complete all as specified and as directed.

Supply and fixing 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Material and labour for point wiring (surface type) for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC casing caping of suitable size with all accessories and PVC rectangular boxes for mounting switch, socket and fan regulator etc complete all as specified and as directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

.-Ditto- all as per item No 59.00 here-in-before but for 3 pin 6 amps switch socket combination on the independant board with 1.5 Sqmm cable and -ditto-.

.-Ditto- all as per item No 59.00 here-in-before but for 3 pin 6 amps switch socket combination on the same board with 1.5 Sqmm cable and -ditto-.

.-Ditto- all as per item No 59.00 here-in-before but for one 5 pin 6/16 Amps switch socket combination on independent board with 2.5 sqmm PVC (FR-LSH) insulated un-sheathed copper conductor cable multistranded conductor 1100 volts grade and 2.5 Sqmm PVC (FR-LSH) copper conductor cable as earth continuity conductor and -ditto-.

Supply and fixing piano switch flush type single pole one way 5 Amps complete all as specified and as directed.

Supply and fixing switch socket combination 2 in 1, 3/5 pin, 5 Amps, 230 volt flush type complete all as specified and as directed.

Supply and fixing switch socket combination 2 in 1, 5 pin, 5/15 Amps, 230 volt flush type universal complete all as specified and as directed.

Supply and fixing ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and as directed.

Supply and fixing for lamp holder suitable for batten fittings complete all as specified and as directed.

Supply and fixing for 10watt, 230V LED Lamp, 6500K, 950lm, with B-22 base suitable for holder fittings complete all as specified and as directed.

Supply and fixing recess mounting LED light fitting luminaire, fixture size 600 x 600mm, 24 Watt, 2640lm, 5700K, 240V with inbuilt occupancy sensor inbuilt capability of switching on/off basis the occupancy in any space with CRCA powder coated white after phosphochromate treatement and powered by an isolated electronic driver SELV output electronic driver with output short-circuit protection, surge voltage protection including all accessories and connecting to celling rose with twin core 0.75mm flexible copper conductor wire/cable, suitable for mounting with grid ceiling complete all as specified and as directed.

Supply and fixing of 1 x 10 Watt environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head back-lit LED luminaire comprising of high brightness LED with IP66 complete all as specified and as directed.

Supply and fixing of surface and wall mounted LED batten with aluminum housing & integrated electronic driver with 10 Watt LED tube, 240V, 600mm long including all accessories and connecting to celling rose with twin core flexible copper wire complete all as specified and as directed.

Supply and fixing of compact street lighting luminaires with deep drawn housing for single 25 Watt LED with toughened glass protection, pressure die cast aluminium housing IP66,with epoxy white powder coated and fixing bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length 1.2 mtr ,fixed over the vertical wall through two numbers mild steel clamp of 25mm width ,3mm thick MS flat strip and four Nos nuts,bolts & washers of 12mm dia ,150mm long grouted into wall complete all as specified and as directed.

Supply and fixing PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 250 mm x 200 mm and 50 mm deep complete all as specified and as directed.

Supply and fixing of MCB DB SPN 8 ways 240 Volts, double door including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed.

Supply and fixing sheet metal enclosure for DB single pole and neutral 2 way without bus bar, single door 240 Volt complete all as specified and directed.

Supply and fixing MCB 6 to 32 Amps, SPN, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and as directed.

Supply and fixing MCB 6 to 32 Amps, SP, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and as directed.

Supply and fixing RCBO 40 Amps, SPN, 100mA, 240 Volt complete all as specified and as directed.

Supply and fixing and testing PVC insulated aluminium conductor cable, 1100 Volt grade, heavy duty served with inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed, two single core stranded conductor flat or circular, 10 Sqmm, nominal cross sectional area, as in service connections suspended by insulating hangers not more than 1 metre apart including 4mm dia. suspension wire complete all as specified and as directed.

Material and labour for house service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90° bends. M.S. hook and stay or guy complete all as specified and as directed.

Supply and fixing of single pole and neutral enclosure with a two pin and earth plug and socket 15 Amp complete with one 20 Amp single pole MCB, 240 Volt "C" series, breaking capacity 10 KA complete all as specified and directed.

Material and labour for taking out existing LT pole (9.00 M) by disconnecting all electrical connections, breaking supporting PCC and including excavation work required and shifting the same within 10 meter distance and re-fixing by providing all earth work and PCC foundation as required and making all electrical connection complete all as specified and directed.

Materials and labour for chemical earthing complete with copper earth plate electrode 600 mm x 600 mm x 3 mm thick, burried directly in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with copper strip 32x 6mm as earthing lead by means of nuts, bolts, check nuts and washers of copper upto 7.5m long protected by galvanised iron pipe of 40mm (light grade) and connected to main switch board or terminal block etc.Earthing pit should be filled with ground enhanced material, highly conductive and anti corrosive compound of required quantity surrounded to copper earth plate and filled with clean earth soil having good earth result and giving below 1Ω. Watering pipe should be 20mm dia (medium grade) including concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. Note: Contractor should submit earth test report to AGE(I).

Supply, installation, testing and commissoning of Servo Controlled voltage stabilizer of capacity 10KVA for automatic operation, three phase naturally oil cooled indoor type & designed for input variation between 340 V to 460 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second complete all as specified and as directed.

Materials and labour for Air termination, single pointed, copper rod 12mm dia and 300mm long complete all as specified and as directed.

Materials and labour for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and as directed.

Supply and fixing copper strip 20 x 3.15mm with saddles and fixing screws etc for roof conductors and down conductors above ground complete all as specified and as directed.

Supply and fixing ceramic insulator suitable for fixing of copper strip used for lightening protection mesh and down conductors with copper screws complete all as specified and as directed.

Materials and labour for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with copper strip 20x3mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 32mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. Note:- Contractor should submit earth test report to AGE(I).

Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed. Note:- Contractor should submit earth test report to AGE(I).

Ms ARENKOKLA CONTRUCTION

M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE