Repair/renovation of lab No. 152 (Ist floor) of Cotton Section in the premises of College of Agriculture at CCS HAU, Hisar. (including EI work)

Amount

Civil work 1 to 31:- Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge: Nominal concrete 1: 1.5:3 or richer mix (i/c equivalent design mix) (HSR 5.23.1)

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. (HSR 5.27)

Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Centering and shuttering including strutting, propping etc. and removal of form for: Shelves (Cast in situ) (HSR 6.30.4)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D or more. (HSR 6.33.6)

Half brick masonry with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level: Cement mortar 1 :4 ( 1 cement :4 coarse sand. (HSR 7.28.2)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charae but excludina the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). (HSR 9.46.1)

Providing and fixing tiled false ceiling of specified materials of size 595x595mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T' of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approve d texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge: GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. (HSR 9.47.1)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (HSR 10.62)

Providing and fixing ceramic & Glazed tiles/ vitrified tiles/ of any size of approved make in floors / dados, laid in any pattern as specified over base of 3 mm thick adhesive of reputed brands as per IS specification 15477-2004 using 5 Kg. adhesive per sqm area of tiles and jointed with white cement slurry mixed with pigment to match the shade of tiles excluding cost of tiles.(HSR 10.73)

12 mm cement plaster of mix : 1 :6 (1 cement: 6 fine sand) (HSR 11.5.4)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1 :6 (1 cement: 6 fine sand) (HSR 11.6.2)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR 11.58)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer. (HSR 11.64.1)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer. (HSR 11.67.1)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws (HSR 12.37.3)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 75 mm (HSR 12.102.3)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (HSR 12.157.1.1)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (HSR 12.157.2.1)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. (HSR 12.158.2)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (HSR 30.21)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work (HSR 30.28.1)

Providing edge single molding to 17-20 mm thick granite stone counters, vanities etc. including machine polished to edge to give high finish etc., complete in all respect as directed by Engineer- in-charge. (NS)

Removing of wooden glazed shutters of fume hood and shifting the same to store, complete in all respect as directed by Engineer-in-charge (NS)

Providing and fixing 4'' long aluminium T-bolt with necessary screws etc. for aluminium shutter under worktop, complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing 15 mm to 18 mm thick Z-Black granite stone (polished) on worktop laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade including rubbing and polishing, complete. (NS)

Providing and fixing wall cabinet of size 12’-0’’ long 2'-6" high and 1'-0" deep consisting of following:- (i) 19mm thick BWR Grade-II block board (ISI mark) of approved make having three horizontal pieces (one at top, one at Centre and one at bottom) vertical pieces @ 2'-0" c/c for making compartments (each for size 2'-0" x 2'-6"). Outer face of the cabinet except back finished with1mm thick plastic laminated sheet (ISI mark) of approved make, shade & colour and inner side of cabinet finished with primer & painting. (ii) 6mm thick plywood BWR Grade-II (ISI mark) of approved make on back of cabinet. (iii) 30mm thick openable shutters in all compartments (each of size 2'-0"x 2'-6") consisting of 4mm thick glass in wooden style frame of commercial hard wood such as hollock, champ, chikrasy & chaplash. (iv) Wooden beading of commercial hard wood such as hollock, champ, chikrasy & chaplash etc. of size 0'- 3/4" & 0'-1/2" on all edges. (v) Angle iron 1'-6" long (at bottom of rack/cabinet) of size 25mmx25mmx5mm @ 4'-0" c/c embedded in cement concrete 1:2:4 blocks after making khudas in wall and MS flat at top of cabinet @ 4'-0" c/c of size 25mmx6mm. (NS)

Providing and fixing 3’’ long hasps and staples of aluminium with necessary screws etc. for aluminium shutter under worktop, complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing 6mm thick HPL Sheet Strips of 4’’ width (Make:-Green, Century, Alstone or Sunderk of approved colour) for worktop face including adhesive etc., complete in all respect as directed by Engineer-in-charge. (NS)

Removing of existing cabinet shutter with chowkat by making recess in wall including remonving its fitting for re-use and shifting the same to store, complete in all respect as directed by Engineer-in-charge. (NS)

EI work 32 to 58:- Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) (HSR 23.3.6.1)

1 run of Size 2.50 Sqmm(1.1.80mm) (HSR 23.3.6.2)

Supply and erection of MS conduit pipe 1.6 mm thick , ISi marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS pipe of 25 mm dia (HSR 23.6.6.2)

Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia (HSR 23.7.6.2)

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. (HSR 23.8.4)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data (HSR 23.8.10.1)

6 Modules ( HSR 23.8.10.4 )

12 Modules( HSR 23.8.10.6 )

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch (HSR 23.8.11.1)

15 amp 1 way switch (HSR 23.8.11.3)

5 amp socket (HSR 23.8.11.4)

15 amp 6 pin Socket (HSR 23.8.11.5)

Step type Fan Regulator 2 modules 300 watt (HSR 23.8.11.7)

Supply and erection of miniature circuit breaker/isolator 240/415 V in the existing distribution board including making necessary connections 6 amp. To 32 amp (SP) (HSR 23.22.5.1)

Supply of GI pipe (B-Class) for suspension rod of ceiling fan including threading if required. 15 mm dia (HSR 23.23.2.1)

Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as requiredt.(HSR 23.23.9)

Providing and installing spirit type air conditioners, four star rating inverter type with copper coils 1.5 ton capacity+ 10%) fitted with super tropical-DC PAM inverter-return cooled-rotary compressor operating on refrigerant R-410-A suitable for wall mounting confirming to IS: 1391 (pat-2) 92 (except power consumption norms) with upto date amendments, suitable for operating on 230 volts, 50Hz single phase A.C. supply having following specifications:- i) Cooling coil row- 3 Nos. ii) Air flow (CMH)-1000 cum/hr iii) Sound level (H/M/L)-45/38/26 iv) Louvers swing-3D + 3D Auto etc. complete in all respect (NS) Make O general/Toshiba/Mitsubishi (Heavy Industries)

Providing and installation of automatic voltage stabilizer of Single Phase 5.00 KVA capacity copper would heavy duty 100 volt up of Logicstate/Voltstar/Bluestar/V-guard make ISI marked complete in all respect (NS).

Providing and fixing in position powder coated MS stand for outdoor units of air conditioners including suitable nuts & bolts etc. of nest quality complete in all respect (NS)

SITC 20 W Led1200 mm Batten light. The Astra fixture is a surface & wall mounted Led Battan with extruded aluminium housing and robust construction PF greater than .95 system wattage led 20 w with minimum 2000 lumans in 5700 k a) Philips, Bajaj, Havells or equivalent (NS)

Wall mounting fan 400mm PF>95 with wall guard & having 3 speed control. Make Havells, Bajaj, Crompton (NS)

Supply, installation of interconnecting referigrant copper piping of various sizes required for all full functionary of the system etc. complete in all respect duly insuated with closed cell nitrile rubber as per specification of the manufacturer suction 6/8” and delivery ½” outer dia 9 mm insulation Make Hitachi/total Line/Rajko/Maxflow (NS)

Providing and fixing UPVC pipes of 25 mm various sizes for disposal of condensed water drainage from indoor unit to nearest disposal point in toilet/outside as per direction of the EIC/consultant/complete in all respect Make Supreme/Prince/finolex (NS)

S/I/T/C of push ON/OFF type 25 A modular type motor starter switch (white colour) for AC’s including the cost of petty material required to complete the job upto entire satisfaction of Engineer-in-charge (NS) Make: Schneider/Crabtree/ Athena.

S/E of ceiling fan 1200 mm capacitor type complete with shackle and 300 mm downrod etc. (NS)

S/E Data Point Internet Jack RJ 45 complete in all respect. (NS)

S/E of recessed type 42 watt full window glare free opal diffuse LED panel of size 595x595mm suitable for Armstrong/POP/GB ceiling with M.S. powder coated white housing . Total system lumens of 42 watt LED should be 5100 or above in cool day light ( 5600 K to 6500 K), power factor 0.95 CRI (Ra) 80, LED lamp efficiency> 100 Im/W, Average life 50000 hours complete with all accessories as required with connections Make Havells, Phillphs , Bajaj (industrial) (NS)

Vikram Contractor

nagpal and company