SPL REPAIR TO BLDG NO P3 (JCOs FAFA ACCN) AT USMAN RD, PROVN OF FALSE CEILING IN BLDG NO T49 AND PROVN OF FALSE CEILING AND ROOF SHEETING AT BLDG NO 3A USMAN ROAD UNDER GE (WEST) LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Dismantling brick tiles or terracing tiles including existing water proofing treatment of any description from roof surfaces and removing rubbish to a distance not exc. 100m, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) such as beams, roof, shelves, manhole cover, chajjas and similar suspended work (reinforcement cut to facilitate demolition) complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed. (Note:- cutting hole in wall is deemed to be included in the rate quoted)

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed. (Note:- cutting hole in wall is deemed to be included in the rate quoted)

Taking down eaves gutters rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc. including cleaning for refixing or removal from site (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M & L Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 20cm in girth complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 10mm thick in CM 1:3 on ceiling finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L plain Cement Concrete 1:3:6 type C-0 (using 12.5mm graded stone aggregate) as in filling in pressed steel frames complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm graded stone agg in RCC lintel,Chajjas, RCC slabs and the like including necessary form work complete all as specified.

M&L 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc.finished even anf fair complete all as specified and directed.

M&L Mild Steel TMT bars 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work quality conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

S&F in repair 'E' board everest make 600x600x4mm thick white prelaminated sett embosed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be poweder coated white. The frame work shall comprise of main runner made from 0.33 mm thick GS sheet and of size 24x32x300mm abd soaced at 1200mm centers securely fixed to be structural soffts by approved hangers at 1200 mm maximum centrers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug level and justers and screws etc. The last hanger at the end of each main runner shall not be grater than 450mm from adjacent wall, Flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm center to from 1200x600mm modules cross tee longer than 600mm to be supported independtly. 600x600mm dodules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee, perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture's instructions complete all as specified and directed.

S&F Gypsum Board 12mm thick , white ceiling boards of approved texture at all height laid on hot dipped GI imposed grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick GI sheet of size 24x32x300mm and spaced at 1200 mm C/C securely fixed to the structural soffits by approved hangers at 1200mm c/c. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, screw etc. The last hanger at the end if each main runner shall not be greater than 450mm from adjacent wall, flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runner at 600mm C/C to form 1200x 600 mm modules cross tee longer than 600mm to be supported independently 1200x600 dodules formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee perimeter wall angle shall be made of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacturers instructions complete all as specified and directed.

M&L providing and injecting chemical emulsion along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed.

M& L treating of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement morter 1:2 (1 cement :2 coarse sand) to match the existing floor complete all as specified and directed.

S & F pressed steel door frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S & F pressed steel door frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F anodised aluminium powder coated (Powder coating not less than 50 micron thick) three track sliding type glazed window frame and shutter with 5mm thick plain glass fixed open track section 100x38x1.2mm having three track (two of plain glass and one of SS wire cloth of 0.36mm nominal dia of wire and average width of aparture 1.40mm) with members of window shutters of section 38x12x1.2mm and other standard Bombay sliding section incl all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats glazing clips, rubber packing aluminium snap beading etc all as specified and directed.

S&F powder coated (Powder coating not less than 50 micron thick) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle(1 no.) complete all as specified and directed.

S&F powder coated (Powder coating not less than 50 micron thick) Anodised Aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified and directed.

S&F factory made Solid PVC door frame of size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.)

S&F Factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site as per specifications & drawing.

S&F 100mm size stainless steel butt hinges, medium weight and fixed with screws complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 150mm floor door stopper of aluminium alloy body and tongue anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 18 mm thick factory made solid WPC flush shutter made from co-extruded three layer rigid foam sheet (single extruded process) with 0.8 to 1mm thick outer face layer having density not less than 1400 Kg/Cum and density of central core material not less than 600 Kg/Cum manufactured by an ISO 9001:2015 certified company and fixing in frame , shutter , shelves & partition etc at site as per specifications and drawing complete all as specified and directed.

S & F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified

S&F Magnet ball catches with 8mm dia steel ball and brass body and striking plate for cup board/cabinet shutters complete all as specified and directed

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles, superior quality of size 300 x 450 x 7mm thick in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 and dismantling of existing tiles complete all as specified and directed.

M&L 20-25 mm thick Kota stone slab, machine cut and polished as in flooring, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of stone, laid over and including 20mm thick screed bed in cement mortar 1:6, including rubbing, grinding and mirror polishing complete all as specified and directed.

M&L 18-20 mm thick Kota stone slab, machine cut and polished as in risers of steps, skirting, dado and pillar, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of stone, laid over and including 10mm thick rendering in cement mortar 1:4, including rubbing, grinding and mirror polishing complete all as specified and directed.

S & F Granite 20mm thick of any type (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM 1:4 complete all as specified and directed

M&L for machine pressed precast inter locking paver block of any shape and size conforming to IS 15658-2006 of 60mm thick rubber moulded coloured of M-35 grade laid over and including 50mm thick sand cushioning and joint filled with fine sand incl levelling and tamping and sweeping etc complete all as specified and directed (Note colour pattern for laying of paver approved as approved by GE)

S&F Exterior finish floor tiles of appproved size 10 to 12mm thick, superior quality, approved shade, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Make: Endura/ Duracrete/ Naveen/ Eurocon/ NITCO.

Dismantling existing water proofing treatment of any description from roof surfaces and removing rubbish to a distance not exc. 100m, complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) M&L 10mm thick screed bed or bedding layer in CM 1:3 using 100% coarse sand over roof slab, finished surface even and smooth without using extra cement including and mixed with 3% integral water proofing compound complete as directed. (b) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (d) M&L 40mm thick brick tiles of best quality well kiln burnt over and including 15mm thick screed bed in cement mortar 1:4 and jointing and pointing in cement mortar 1:3 by mixing polymer based liquid water proofing compound as per manufacturer's instructions complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane on verticle surface all as given below:- (a) M&L 10mm thick rendering in CM 1:3 using 100% coarse sand over roof slab, finished surface even and smooth without using extra cement including and mixed with 3% integral water proofing compound complete as directed. (b) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (d) M&L 10mm thick rendering in cement mortar 1:4 by mixing polymer based liquid water proofing compound as per manufacturer's instructions complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in bed blocks, roof kerbs or mud stops, rounded or champhered on edges including necessary formwork complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for preparation of new ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of cement base paint over one coat of primer on previously treated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

S&F in repair 15 mm bore single lever basin mixture central hole for WHB system without popup waste system with 450 mm long braided hoses complete all as specified and directed. Make :- Jaquar(KUBIX PRIME) Cat part No. KUP-35011BPM/ Plumber (Aura) Cat part No. ARA-3104/Hindware (CORA) Cat part No. F440009

S&F in repair single lever wall mixture 3-in-1 system with provision for overhead shower with 115 mm long bend pipe, connecting legs and wall flange(without over head sower) screwed down for 15 mm bore GI pipe complete all as specified and directed. Make :- Jaquar(KUBIX PRIME) Cat part No. KUP-35117PM/ Plumber (AURA) Cat part No. ARA-3101LB, (ORNAMIX PRIME) Cat part No. ORP-10117PM

Supply & Fixing in repair stop valve/Angle valve fancy type cast copper alloy with capstan head chromium plated screwed down high pressure with long shanks and fly nuts screwed for 15mm bore pipe complete all as specified and directed

Supply & Fixing in repair 15mm bore PVC connection 450mm long with brass/PVC coupling and washer complete all as specified and directed

Supply & Fixing in repair copper alloy long body bib taps chromium plated suitable for 15mm bore pipe with captain head complete all as specified and directed

Supply & Fixing in repair gun metal gate valve screwed both ends to 20mm bore pipe complete all as specified and directed

Supply & Fixing in repair CP shower rose fancy type125mm thick with or without swivel joints any size including fixed to steel pipe or union complete all as specified and directed

Supply and fixed in repair PVC rotational moulded over head storage tank 1000 Lts capacity including 20mm dia PTMT float valve complete all as specified and directed

Supply and fixing in repairs of vitreous china wash hand basin flat back size 550x400mm and including brackets and CP waste coupling 32mm dia and PVC waste pipe,complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

Supply & fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Supply & fix in repair CP Brass Tabular Towel Rail, 20mm dia D type 60cm long between flanges complete all as specified and directed

S&F glass corner shelves fancy type 6mm thick 250x250mm size and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

Supply and fixed in repair 75 mm dia PVC floor trap with CP grating including jointing to waste pipe fixed in cement concrete complete all as specified and directed

S&F in repair stainless steel 25mm bore curtain rods including bracket/junctions /wall to wall and with rings of best quality as approved by Engineer-in-Charge complete all as specified and directed

S&F PVC (SWR) pipes in any length with rubber ring joints fixed to wall 110 mm bore complete all as specified and directed

S&Fin repair PVC (SWR) pipes in any length with rubber ring joints fixed to wall 75 mm bore complete all as specified and directed

S&F PVC bends 110 mm bore fixed and jointed with solvent complete all as specified and directed.

S&F PVC bends 75 mm bore fixed and jointed with solvent complete all as specified and directed.

S&F PVC vent cowl 110 mm bore fixed and jointed with solvent complete all as specified and directed.

S&F PVC vent cowl 75 mm bore fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

Supply & Fixing in repair sink without drainage board size 560x410x200 mm made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes pipe & coupling etc incl bedding in cement mortar to draft wall or cantilever brackets and connection union to pipe all as specified

M & L for sunken treatment as per following specifications :- (a) Taking out existing water proofing treatment in sunken floors including taking out floor finish, PCC filling, traps etc and cleaning & washing the RCC surface to recieve water proofing treatment and removal of the retrieved material where directed. (b) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (c) Sealing of joints of pipe with epoxy putty CICO POXY LC or epoxy mortar CICO POXY 2125. (d) Applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of TAPECRETE P-151 and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (e) Appying a coat of TAPECRETE brush topping 1.5mm thick consisting of one part of TAPECRETE P-151, two parts of cement and two parts of silica sand by weight and cured to 2 days. (f) Applying 15mm thick plaster in CM 1:4 mixed with CICO super @ 100ml per 50 Kg cement on treated surface. (g) Filling the sunken portion with PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) upto required level complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 104 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 104 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item no 104 above but for one bell point controlled by one bell push.

All as per item no 104 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F bell push switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F call bell (Ding dong) AC 230 Volt complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S& F Decorative wall light fixture made up of Metal base, synthetic white in colour and square/round metal base with bend pipe and glass globe with nickel finish, ( B-22/E27 base), with 01 No. 7/9 W LED Bulb, 230 V, 6000K, complete incl all required electrical connecting arrangements all as specified and as directed. Make Phillips Model Grace or Jaquar lighting cat no JNL-NKL-WLBPGG001E27/ Havells decorative model Floretine WL 1LS B22 SS cat no LHFOAJE1TZ1I060 ( Note: Rates incl 01X 7/9 W LED Bulb with each fitting)

M & L of Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of nut, bolts, check nut & washer of galvanized iron or of steel, earth lead protected by 15 mm dia GI pipe light grade, watering pipe 20 mm dia GI light grade, GI wire mesh, GI funnel, alternate layer of char coal and salt, PCC chamber, recessed for and including RCC cover including all necessary excavation & earth work, earth 7.5 mtr wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No 3 of MES SSR Part-I 2009 complete all as specified and directed .

S&F in repair LED Building security light 24/25 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts. Make philips Green line smart cat noBRP042 LED 25 CW R1 S1 PSU GR/ Bajaj Edge nxt LED cat no ENXT P 24L WH CR PC SD/ Eveready Mini might cat no LED SL025157-02

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 20 W, 6000 K,110 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as specified and directed by Engr-in-charge. Make Phillips Smart brite cat no BN 021 LED 22S 6500 PSU GR/SI or/Havells Endura linear neo cat no enduralinear neo BS22WLED865SPCWH/ Bajaj LED batten BCLAB 20W WH LED P

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,100 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed by Engr-in-charge.Make:Phillips smart brite cat no BN 021 LED 12S 6500/4000 PSU GR/SI or/Havells Endura linear neo cat no enduralinear neo BS10WLED865SPCWH/ HPL Neptune plus 10 w HLPT51510CW

Supply & fixing bulk head light fitting made from cast aluminium body with heat resistance pressure die cast housing, IP-65 protection cover suitable for bulk head fitting integrated type 6.5 W LED, 6000K , 105 lumens/watt including inbuilt electronic driver complete all as specified and as directed. Make: Philips Vista glow ordering code : WT140W LED7S NW PSU S1 PC./ Bajaj wee plus cat no BIBWP 6W LED/

S&F in repairs of surface type round LED 12W downlighter all as per specified and directed. Make: Havells Integra neo (surface) cat part no: IntegraneosurfaceDLS15WLED840S/ Phillips sleek surface SM250 & SM251 (Circular)/ Bajaj sleek surface LED cat no. BGSLO SLEEK SURFACE 12W WH RD

S&F in repair super bright LED (2X2), 36 W, 6000 K recess mounting with high efficent LED source all as per specified and directed.Make Philips cat part no.: RC360B LED36S -4000/6500 V1L60 W60 PSU OD OC/Havells Pluto Neo Panel cat no PLUTONEO2X2PLR34WLED857S/ Bajaj SKYLUX GZI SERIES -RECESSED cat no BZRSQL 36W GZI WH

Taking down existing ceiling fan, exhaust fan of any type and capacity and fixing back to location as directed after oiling greasing and painting including making all electric connections complete all as specifed and directed.

Supply and fix wall mounting fans 400 mm (white) string controlled oscillating type including provn of flexible three core cable from ceiling rose to terminal for making connection, fitting on wall including all necessary fixing accessories complete all as specified and as directed . Make Orient wall 44 (white)/Crompton FizzAir HI speed/Usha Mist Air Icy

S&F sheet metal enclosure for MCB DB double door type, triple pole and neutral 4 way, 415Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, triple pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 32/40 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

M/S S S A ASSOCIATES

M/s Chandra Mohan and Sons

M/S Reliance Construction

M/S SWATI CONSTRUCTION

R K CONTRACTOR AND SUPPLIERS

M/s Sudhir Enterprises

sanjay enterprises