Special repair of Sub Health Centre at village Silani, Alipur and Baluda in Gurugram Distt.

Amount

Dismantling Concrete renforced cement concrete with clearning and straighening and cutting of bars if required (HSR: 8.6) (e)

Cement concrete 1:1 1/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering , laid in position complete in all respect (HSR 10.82+10.95a)

Steel reinforcement TMT steel bar FE-550 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate ofRCC including stairghtening, bending, binding, wastage, overlaps, welded joints, spacer, bars, chairs, stays, hangers and annealed steel wire etc.and placing in position complete in all respect for all heights/depts/story/basement etc. (HSR-18.22) (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement).

Scrapping of cement and sand plaster in side building as per HSR 8.32 c

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement HSR 8.5 b

Demolishing Roofing mud phaska in tile terracing as per HSR 8.8 g

Plastering on wall 12 mm thick cement plaster 1:5 HSR: 15.6 (First Storey)

Second Storey) Main Building Parapet

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc(HSR 13.13)

Cement concrete 1:2:4 gola 10 cm X 10 cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. As per HSR 13.64

Half brick masonry 11.43 cm thick wall laid in cement sand mortar 1:3 in super structure (2nd storey) as per HSR 11.48 (b)

Plastering on under side of ceiling 10 mm thick cement plaster 1:4 as per HSR 15.52

Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm Thick including concrete base as per HSR 8.25

Conglomerate floor 25 mm thick cement concrete topping 1:2:4 as per HSR 14.8

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving door and window frame of size 114 mm X 50 mm with 40 mm wide double rebate.(HSR 18.34 d)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate(HSR 18.34b)

Providing & fixing vitrified tiles of size 600mm X 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO(HSR 14.89) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material(HSR 14.89)

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- as per HSR 17.93 a iii. (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (Duro, Green) 35 mm. Thick (HSR 17.93a iii- note I under 17.18))

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy annd chaplash, etc. (non coniferous timber other teak conforming to I.S specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (i) 30 mm thick (HSR 17.92 (i) - Note I under 17.18

Providing & fixing PVC Rain water pipe 6 Kg Pressure of ISI Mark in cement mortor during masonery work. 100MM dia PVC pipe 6Kg. Pressure(HSR 13.89a)

Providing & fixing PVC Bend ISI Mark 100MM dia PVC pipe 6Kg. Pressure(HSR 13.90a)

Providing & fixing Ist quality ceramic glazed wall tilesconfirming to IS 15622 (thickness to be specified by manufacturer)of approved make in all colors,shade except burgundy,bottlegreen,black of any size as approved by engineer-In Charge in skirting ,risers of steps and dados over12mm thick bed of cement mortor 1:3 coarse and jointed with grey cement slurry,including pointing in white cement mixed with pigment to match the shade complete. Size of ceramic Glazed tiles 300mm X 450mm(HSR 14.92 b) Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing & fixing ceramic tiles/ anty skid tile of size 400mm X 400mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material(HSR 14.91)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR: 16.1) (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR: 16.3) (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge)

Painting one coat with synthetic enamel Paint in all shades on old wood-work, or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.7) (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge)

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing surface to the required finish, complete.(HSR: 16.24)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work.(HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Cost of aluminium fitting cokmplte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt)- for single lead shutter(HSR 17.72a)

Providing and fixing sliding bolt with nuts and screws etc. complete- aluminium- size 300 mm x 16 mm(HSR 17.83b-i)

Providing and fixing of 4mm thick glass panes with beading as per HSR 18.30 b

Providing & fixing vitrified tiles of size 600mm X 600mm of approved make in skirting/dados laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material(HSR 14.90)

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flags for connection in tanks complete in all respects to the satisfaction to the Engineer-In-Charge. (HSR-30.119)1000 Ltr.

PROVIDING AND FIXING IN POSITION BEST QUALITY STAINLESS STEEL SINKS WITH COMPLETE FITTINGS AS FULLY DESCRIBED IN ITEM NO. 30.51 ABOVE. 600 mm x 450 mm x 200 mm(HSR 30.53a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or c INDIAN MAKE 600mmx450mm (HSR 30.71 a-i)

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) Bib cock (HSR 30.75c)

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge) 15 MM STOP COCK Stop cock male and female end(HSR 30.76a-i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION C.P Brass 15 mm x 450 mm(HSR 30.82 b-iii)

CONSTRUCTING BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement Mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation Cement mortar 1:2:4 BENCHING 12 mm THICK CEMENT PLASTER 1:2 with a floating Size 450 mm x 450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 40 kg with C.C. topping )(HSR 29.84a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONIC TYPE, Consisting of- Single trap symphonic W.C. Suite white (HSR 30.5a-i)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. White plastic seat (Solid)(HSR 30.13 i)

PROVIDING AND FIXING IN POSITION BESTINDIA MAKE LARGE FLAT BACK or Angular lipped from Urinal 610 MM HIGH consisting of: Flat back lipped or angular urinal basin or VITREOUS CHINAWARE; (to the approval of the Engineer-in-charge)(HSR 30.25 i)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work.(Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge)(HSR-16.60)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and otther sections of approved make conforming to IS ;733 and IS 285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junction, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling C.P brass/stainless steel screws, all complete. (with Powder cating of 50 micron. as per HSR 17.95 + Note 1.

Providing and fixing in glazing aluminium door, windows, ventilator shutter and partitions etc. with pvc/neoproene gasket etc. complete (Cost of aluminium snap beading shall be paid in basi items) B with float glass panes of 5.00mm thickness as per HSR 17.98 b

Providng and fixing 12mm thick prelaminated board flat presed three layer or graded wooden particales board conforming to IS 12823 grde 1 type II in paneling fixed in aluminium doors. Windows shutters and partition frames with CP brass/stainless steel screws wtc. complete. Pre laminated partical board with decorative lamination on both site as per HSR 17.97 b

Providng aluminium jali of thickness 7mm thick with opening 75X75mm of including anodizing and fixing in frame with cost of screws etc. complete HSR 17.100

Providing and fixing false ceiling with grooves with 12mm to 15mm thick 600X600mm best quality mineral fiber tiles of approved make fixed on MS steel runners frame i/c cost of screws angles, cleats, rawel plugs, with taping and painting, etc. complete in all respect as per approved by Engineer- In- Charge. as per HSR 13.93

Providing and fixing double action hydrolic floor spring of approved brand and manufacture as IS 6315 marked for doors including ocst of cutting floors as required with brass cover Plates with brass pivot and single piece M.S Sheet outer box. with brass cover plate As per HSR 17.99 b

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertion 35mm thick (HSR 17.91 b) note I under 17.18))

Distempering with washable oil bound distemper (of approved manufacture) one coats on old distempered work.. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.59).

Preparation of sub grade, including trenching, rough dressing of spoil final dressing of earth,to given levels and camber, watering, rolling with road roller, and compacting the bed as per HSR 24.1

Providing and applying primer coat with bitumen emulsion (S.S grade-I) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 Kg/Sqm using mechanical means as per MoRT&H specification for road & bridge (5th Revision) of 2013 as per drawing and design directed by the Engineer complete in all respects as per clause No.502. (N.S.)

Providing and laying 80mm thick interlocking paver block of all shape and color in design mix concrete M-35 over a bed of 30mm thick fine sand complete all respect as per HSR 10.159

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 15 mm dia nominal bore(DSR 18.10.1)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 20 mm dia nominal bore(DSR 18.10.2)

Recovery Items:-Bidder have to quote rate for recovery items at least or more than reserve price. The rate quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency.T Note:- The reserve rate/amount is minimum amount to be used as base for quoted purchase rate by the agency. No rates/amount below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.-- Door @ 150 Each

Tiles @ 4.50 Each

Brick Bats @ 400 Per cum

Dismantlled Steel Note:- In Case of any difference in the DNIT & Nomenclature of any of HSR Items of Civil, PH Work Depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable

Pulkit Aggarwal