PROVN OF 01XTOILET WITH 04X INDIAN COMMODE 01XWESTERN COMMODE AND 03XURINALS OPP TO BARBER SHOP AT BLDG NO. P-129 DEPOT AREA CHHEOKI MIL STN, EXTN OF CBOS BLDG NO. P-60 AT SCE AND TOILET BLOCK FOR LADIES AT KADAM KUNJ AT NEW CANTT UNDER GE (W) PRAYAG

Amount

Surface dressing not exceeding 15 cm deep and getting out in soft/loose soil, complete all as directed.e

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation etc. or for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in soft/loose soil, complete all as directed.

Rough excavation, not exceeding 1.5 m deep and getting out in soft/loose soil, complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Spreading and levelling in layers not exc. 25cm thick and well ramming including watering the earth under floor, complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified.

RCC M-25(design mix) using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed by Engineer-in-Charge.

RCC M-25(design mix) using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

RCC M-25(design mix) using 20mm graded crushed stone aggregate as in cantilevers, bressummers, lintel over 1.5 m span, complete all as specified and directed.

RCC M-25(design mix) using 20mm graded crushed stone aggregate as in slab supported on walls, columns in floors, roofs, landings, balconies and in shelves, complete all as specified and directed.

RCC M-25(design mix) using 20mm graded crushed stone aggregate as in chajja, complete all as specified and directed.

Form work to sides of concrete foundations, footings, basis of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better for rough finished surfaces of concrete complete all as specified & directed

Form work to sides of pillars, posts, struts piers, columns and stanchions and similar works for rough finished surface of concrete complete all as specified & directed.

Form work to sides and soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs etc and similar works for rough finished surfaces of concrete, complete all as specified.

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed.

Form work to chullah hood, chajjas, troughs and similar items including edges for rough finished surfaces of concrete, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified

TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified.

M&L brick work with fly ash bricks(old size), straight or curved on plan exc 6 m mean radius built in CM 1: 6 complete all as specified.

M&L for brick work with fly ash bricks(old size), straight or curved on plan to any radius in half brick thick wall built in CM (1: 4), complete all as specified and directed.

5 mm thick cement plaster rendering in CM 1:3 on concrete surfaces as in ceiling & finishing the surface even and smooth without using extra cement, complete all as specified.

15mm thick cement plaster rendering in CM 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Preparation of newly plastered or unplastered surfaces of ceiling etc. and applying two coats of white wash on ceiling, complete all as specified.

Preparation of new plastered or unplastered surface of wall including cornices pilaster etc, and applying three coats of white wash on wall, complete all as specified.

Preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistance primer, complete all as specified.

Hard core of broken stone/boulders of gauge n exc 63mm deposited spreed and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

75mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection laid in slope 1:12, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight to through out joints of 6mm thicks, complete all as specified.

10 mm thick cement plaster in CM 1:3 mixed with water proofing admixture on concrete surfaces when concrete is green & finishing the surface even and smooth without using extra cement, complete all as specified. Note:-Liquid water proofing admixture shall be measured & paid seperately.

Supply only liquid water proofing admixture.

Water proofing treatment to roof and edges (vertical of tapered portion) shall be done in following sequences:- (a) Proper cleaning the surfaces by sweeping & washing down with water to remove all loose particles, dust/dirt particles etc and complete drying the surface before application of primer. (b) Applying one coat of industrial bituminious primer at the rate of 0.40 lit/Sqm over the plastered surfaces of roof uniformily and primed surface shall be allowed to dry over night as confirming to IS 3384-1986. (c) Applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C @ 1.2 kg/sqm then applying APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 100 mm side overlap and 150 mm end overlap by forced (tourch) application as per manufactures instructions, complete all as specified and directed. contd to item No-32.01

Note:- All water proofing work shall be done as per manufacturer's instructions under supervision of manufacturer's technical staff. The name of manufacturer's shall be approved by GE before execution of respective work.

40mm thick tiles as in roof slab laid over & including 15mm screed bedding in cement mortar (1:4) mixed with polymer based liquid water proofing additive @ 5% by weight of cement or as per manufacturer's instructions and joints of tiles shall be filled with CM 1:3 mixed with crude oil as per SSR-2009(Part-I) on non accessible roof slab, complete all as specified and as directed

Non skid joint free coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Glazed ceramic coloured tiles (450x350mm)/(350x250mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge. Note:-The size & colour of tiles shall be as approved by GE.

Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory Made Solid PVC Moulded Door Shutter with partical board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site all as specified and directed.

Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, and similar works, complete all as specfied.

Preparation of new or previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer, complete all as specified and as directed.

Stainless steel butt hinges with steel pin,100mm long, complete all as specified.

Aluminium anodised, barrel tower bolts of extruded section of size 200mm and fixed, complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 150mm and fixed, complete all as specified and directed.

Figured glass pin headed type, 3mm thick, glazing with oil putty in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover closed pattern with flat bottom & mild steel CP screws, complete connection to drain (outgoing pipe) and to flushing pipe and anti syphonage pipe etc with & including fixing bolts, complete all as specified.

Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white,with front or back inlet and integral foot rests with 'P' or 's' trap, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete, all as specified.

Vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

Chromium plated bottle trap with internal partition 32mm size with 300mm & 190mm long wall connection pipe and wall flange, complete all as specified & directef. Make:-Jaquar or equivalent cat part of make as specified in list of make.

Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs, complete all as specified and as directed.

20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) fixed, complete all as specified

Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

20mm bore Gun metal, globe or gate valves (ISI Marked), with iron wheel head, screwed both ends for iron pipe, complete all as specified.

15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe, complete all as specified & directed.

CP jet spray with holder including 1.0m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified.

PVC valve less symphonic action type flushing cistern 10 ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints, complete all as specified and directed.

Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule fixed, complete all as specified and directed.

15mm bore Stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, complete all as specified.

Tubular towel rail brass chromium plated 20mm dia D type, 60cm long between flanges, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed, complete all as specified and directed.

Toilet paper holder with flap recessed fancy type (stainless steel) fixed, complete all as specified & directed .

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches/floors, complete all as specified and directed.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint fixed to walls with & including clamps, complete all as specified and directed.

PVC (SWR) bends any radius 110mm bore fixed, complete all as specified.

PVC (SWR) junction single (single T) 110mm bore equal or unequal, fixed, complete all as specified and directed.

PVC (SWR) floor trap of 100mm dia of outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

PVC (SWR) vent cowl for 110mm dia, complete all as specified.

150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed complete all as specified and as directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid in PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed. (Note: - SGSW pipe and earthwork shall be measured and paid seperately under respective items of BoQ)

Cutting into existing manholes brick wall built in CM for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC 1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (made out of rubber moulded vibratory cement concrete) any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 grade, pointed with grey cement and pigments, as in path etc laid tightly over & including 25mm thick sand filling under pavers and paking the joints of paver block with sand, including watering and consolidation all as specified and directed by Engr-in-Charge. Note:-Colour & pattern of paver block shall be as approved by GE before execution of work.

Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:4), all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering, complete all as specified.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, complete all as specified and directed.

Non skid coloured ceramic tiles 7 - 8 mm thick area of each tile exceeding 0.18sqm but not exceeding 0.38sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Sheet glass ordinary quality, 4mm thick tinted type, glazing with rubber bidding in squares not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified.

Extruded aluminium alloy handles, fabricated type, anodised of size 125mm and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified.

Bib tap 15 mm bore with flange, CP cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified.

15mm bore pillar tap cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule complete, all as specified & directed

PVC connection 15mm size with brass nuts on both ends of length 450mm, complete all as specified.

PVC (SWR) gully trap of 125/100mm, setting & jointing with solvent cement fixed, complete all as specified.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint fixed to walls with & including clamps, complete all as specified and directed.

PVC (SWR) bends any radius 75mm bore fixed, complete all as specified.

Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs, complete all as specified and as directed.

Ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 20mm bore, complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of ceiling etc. and applying three coats of white wash on ceiling, complete all as specified.

Removing excavated material (soil) not exceeding 50m and deposition where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

Vitreous china bowl urinal flat back size of 465X355X265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws and pointing around urinal back in cement etc and 32mm dia PVC waste pipe, complete all as specified.

Hand shower (Health faucet) (ABS body) mild steel chromium plated for 15mm bore pipe with 1.25m long flexible tube of stainless steel in chrome finish and wall hook , complete all as specified .

100 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed complete all as specified and as directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 100mm SGSW pipe after they are laid in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed. (Note: - SGSW pipe and earthwork shall be measured and paid seperately under respective items of BoQ)

Cutting into existing manholes brick wall built in CM for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC 1:2:4 type B-1 smooth finished and reforming benching as required for 100 mm bore complete all as specified and directed.

Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Removing excavated material (soil) exceeding 250m and not exceeding 500m depositing where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

Plain cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified.

Treating the soil along with external perimeter of building with ATT at the rate of 2.25 litre of emulsion per metre of perimeter wall, complete all as specified.

Treating the soil under plinth protection with ATT at the rate of 5 litre of emulsion per square metre of surface area, complete all as specified.

Treating the top surface of filled earth with ATT at the rate of 5 litre of emulsion per square metre of surface, complete all as specified.

Treating the backfill in contact with foundation with ATT at the rate of 7.5 litre of emulsion per square metre of surface, complete all as specified.

Damp proof course of 40mm thick in PCC 1:2:4 type B-0 to horizontal or vertical surfaces including necessary form work, complete all as specified.

Applying evenly a coat of blown type bitumen @ 1.5 kg/sqm and blinded with clean dry sand @ 0.05 cum per sqm, complete all as specified.

Polythene film, 150 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm, complete all as specified.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil bound distemper over and including 1-3mm thick wall care putty, complete as specified and directed.

Preparation of newaly plaster surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfacesincluding a coat of 3mm birla wall care putty complete all as specified and directed.

Providing and fixing factory made uPVG white colour Sliding window (area not exceeding 2.00 sqm each) three track made of extruded profiles with wall thickness of 2.3mm (+ / -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + / -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed. contd to item No-111.01

(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.).

Anodised alumium grill (anodised transparent or dyed to rquired shade according to IS 1868 with minium anodic coating of grade AC 15 of approved desgin/pattern,with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200mm center to center,including cutting to grill to proper opening for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening,all complete as per requirement and direction of engineer-in-charge

12 mm thick tuffened glass door with suitable locking arrangement with lock (Godrej/link) 6 lever and self closing devices with rebates including jointing cleats of suitable section for fixing builders hard ware fittings door floor spring (Make Sandhoo/Samrat) with two Nos decorative type CP steel angle handle of 200 mm dia, complete all as specified and directed.

Sheet glass ordinary quality, 4.8mm thick, glazing with oil putty in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Vitrified ceramic tiles dark shade 10 mm thick (square/rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Description all as per ser item No.115 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified.

18-20mm thick Machine cut Kota stone slab flooring, bedded and jointed with grey cement slurry and pointed with grey cement mixed with admixture or pigment to match the shade of Kota stone slab as approved by GE, laid over and including screed bed or bedding layer of mortar 15mm thick in Cement Mortar (1:6) including cutting, grinding and mirror polishing, complete all as specified and directed.

Machine cut kota stone slab 18-20mm thick in riser of steps,skirting, dado and pillar, bedded and jointed with grey cement slurry and pointed with grey cement mixed with admixture or pigment to match the shade of Kota stone slab fixed over & including 15mm thick plaster in CM 1:4 including cutting, grinding and mirror polishing, complete all as specified and directed.

Makrana white marble work 18 to 20mm thick (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking plateforms and like fixed over & including cement plaster 15mm thick in CM 1:4 and jointed with white (1:2) using marble dust with admixture or pigment to match the marble shade including rubbing and polishing, complete all as specified.

Rounding to edges of stone slabs one edge such as in steps, cooking platform and other similar situations, complete all as specified.

Stainless steel tubular curtain rod fancy type 20mm dia of conduit wall thickness not less than 1mm with & including brackets and decorative end bulbs/caps, complete all as specified and directed.

Anodised aluminium snap grid frame work of size 605x605mm for false ceiling, complete all as specified.

Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long for hanging snap grid frame work for false ceiling, complete all as specified.

16mm thick board acoustical tegular 600x600 mm in size,fixed in jointless finish with jointing compound and jointing tape as per manufacturer's instructions complete all as specified and directed.

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed.

PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slop required finished even and fair complete all as specified and directed.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

Supply laying jointing and testing LT XLPE and PVC insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sqmm 2 core complete all as specified

Point wiring with 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable in and including 20mm dia medium grade rigid non metallic PVC concealed conduit in wall after cutting chases in wall including 1.25mm thick MS pressed steel terminal box covered with and including 3mm thick laminated sheet top cover fixed flush with wall using brass screws, washers and 1.5 Sqmm single core FRLS PVC insulated sheathed copper conductor wire as earth continuity to common earth and connecting to earth dolly with all requisite accessories such as PVC elbow, Tee, collars, bends etc. for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light / fan point controlled by one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp independent board complete all as specified.

One 3 pin socket outlet 6 amp on same board complete all as specified.

Description all as per srl item No 130 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Socket outlet multipurpose combination 2 in 1, 3 pin, 6 Amp flush type, complete all as specifed.

Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as speciied.

Socket outlet multipurpose combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal,complete all as specifed.

Supply and fixing wall mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed.

LED light fitting 10 watt mirror type (2 feet) with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flrxible copper conductor cable of suitable size complete all as specified & directed.

LED 10 W bulk head fitting with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flrxible copper conductor cable of suitable size complete all as specified & directed .

Exhaust fan 300 mm sweep AC single phase 230 V Metallic steel body Range complete with blades, frames, and louvers including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan with provn of making hole in wall complete with grouting of nuts, bolts and washers and all other accessories required for fixing of fan including testing on completion, complete all as specified & directed .

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 4 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series, complete all as specified.

MCB single pole & neutral 6 to 32 amps 240 volts 10 KA 'C' series, complete all as specified.

Cutting of existing main distribution GI pipe 40mm dia and inserting tee 40x40x25 mm, etc. including necessary all connected accessories for tapping 25 mm connection complete all as specified and directed.

25mm bore Gun metal, globe or gate valves (ISI Marked), with iron wheel head, screwed both ends for iron pipe, complete all as specified.

GI tubes medium grade of bore size 25 mm including all fixing accessories and laid in floor complete all as specified and directed by Engr-in- Charge

Ceiling rose, 3 phase PVC/poly carbonate, insulated body with colour ring for fan point wiring, compete all as specified.

LED light fitting with Decorative ulta slim linear LED lighting fixture with co extruded polycarbonate body environnmental friendly , energy efficient tube light complete with all accessories internally pre-wired and including LED lamp 18 watt 01 No and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified & directed .

Sub main wiring with single core cable 2 x 4 sq mm FRLSH insulated unsheathed flexible copper conductor cable 1100 Volts grade drawn through including drawing in recessed/surface 20mm PVC conduct medium grade alongwith 1x 2.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly and making incoming / outgoing electric connections by using required size copper lugs / thimbles, making good to disturbed surface to match with existing surface, complete all as specified and directed. Note:-2 wire of 4sqmm, 1 wire of 2.5 sqmm and one run of pvc conduit shall be measured as one unit.

MCB single pole & neutral 63 amps 240 volts 10 KA 'C' series fixed, complete all as specified.

M&L for concealed point wiring on wall /ceiling/roof with necessary arrangements with 1.5 Sqmm single core 1100 Volts grade FRLSH PVC insulated unsheathed multistranded copper conductor following colour code in and including PVC conduit of medium grade with all fittings such as bend, tees, junction boxes etc. including Modular metal flush box, Modular white cover plate with frame, of required module at site, fixed with chromium plated screws and washers for switches and sockets, and 1.5 Sqmm single core 1100 Volts grade FRLSH PVC insulated unsheathed multistranded copper conductor as earth continuity conductor (green) connected to common earth dolly and including cutting chases in walls / floors for concealed conduit complete all as specified and directed for the following:- :-

One light / fan point controlled by one way switch 6 Amp complete all as specified.

One 3 pin socket outlet 6 amp on same board with other switch complete all as specified.

Description all as per srl item No 150 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire.

Modular switch one way 6 Amp 1 module (ISI marked), complete all as specified.

Modular socket 6 Amp-2/3 pin combined 2 module (ISI marked), complete all as specified.

Modular socket 6/16 Amp-2/3 pin combined 2 module (ISI marked), complete all as specified.

Modular switch one way 16 Amp 1 module (ISI marked), complete all as specified.

Modular step type fan regulator 120 watt, 2 module (ISI marked), complete all as specified.

4 Module Gang box including Modular socket outlet 20 Amps for AC, incl plug top 20 Amps, 240 Volts flush type white finish with Push ON/OFF button, 16 Amps 240 volts, and LED indicator (RED) incl concealed point wiring on wall /ceiling/roof with necessary arrangements with 4 Sqmm single core 1100 Volts grade FRLSH PVC insulated unsheathed multistranded copper conductor following colour code in and including PVC conduit of medium grade with all fittings such as bend, tees, junction boxes etc. including Modular white cover plate with frame 4 module to accommodate all the accessories complete with internal connections, fixed with chromium plated screws and washers for switches and sockets, including 4 Sqmm single core 1100 Volts grade FRLSH PVC insulated unsheathed multistranded copper conductor (green) connected to common earth dolly and including cutting chases in walls / floors for concealed conduit complete all as specified and directed.

Supply & Fixing ceiling fan 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush less direct current (BLDC) motor, class of insulation : B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service Value ( CMM/W) minimum 6.00, Air delivery minimum 210 CMM 350 RPM ( tolerance as per IS : 374 - 2019), THD less than 10 % ,electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V , 50 Hz, single phase AC supply, earthing etc including necessary connection with ceiling rose with 3 core 1.0 Sqmm PVC insulated round flexible cable and including writing MES No all as specified and as directed.

LED street light fittings 35/36 Watt made up of pressure die cast aluminium housing with high efficient LED as lighting source with toughened glass / PC cover having seperate driver compartment with IP65 protection and impact resistance of IK07 complete with hosing with all accessories pre wired with and making connection with copper flexible cable of suitable size to light fitting fixed, complete all as specified and directed.

Supply and fixing of sheet metal enclosure Double door, VTPN MCB DB, 4 way, 415 volts with 200 Amps rated bus bar, IP-43 complete fixed properly in concealed position incl internal, incoming/ outgoing electric connections by means of suitable sizes of lugs/thimbles and to provide required sizes of flexible conduit at any open surfaces near DB’s of cables/wires all as directed.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

MCCB 100 Amps, 4 Pole, 415 Volts, 50 Hz, 16 KA adjustable thermal & fixed magnetic, complete all as specified and directed.

M&L for concealed sub main wiring with two single core FRLSH PVC insulated and unsheathed copper stranded conductor of size 4 Sqmm 1100 Volts (1P+1N) and one run of copper stranded conductor of size 4 Sqmm for continuous earthing following colour code drawn in rigid non metallic PVC conduit pipe ISI marked of size not less than 25 mm dia including all accessories like bends, tees, junction boxes etc. and connecting incoming/outgoing electric connections by using required sizes of lugs/thimbles complete all as specified and directed. Note :- Two single core cable and one run of earth copper conductor will be measured as one unit length.

M&L for earthing complete with galvanised steel plate electrode 600x600x6mm thick buried directly in ground (top edge of the plate should not be less than 1.50Mtrs below ground level) connected to GI wire 4mm by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 20 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layers of 150mm the, PCC chamber using PCC(1:3:6) type C-1 using 20mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6mm dia round bar @ 75mm C/C both ways with MS handle 8mm dia, plastering 15mm thick CM (1:6) externally up to 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on Electrical plate No.3 of SSR Part-I (2009) and connected to earth test point incl testing and marking Bldg Nos and

writing Test Results (in white) on a black painted M.S. Plate (size 300x300x3mm th) duly welded with angle iron of size 40X40x5mm, 60cm long, fixed with the earth pit chamber by grouting complete all as specified and directed. Note :- (i) GI wire and GI pipe medium grade, up to 7.5mtr shall be deemed to be included in the rates quoted for earthing. (ii) Excavation and earth work in any type of soil strata shall be deemed to be included in rates quoted for earthing. (iii) The rates quoted by the contractor are deemed to be included for MS sheet of size 300x300x3mm th, fixed with necessary nuts and bolts on angle iron of size 40X40x5mm, 60cm long and grouted with PCC block of size 200x200x250mm(PCC 1:3:6 using 20mm grade stone aggregate including necessary earth work for marking the result and purpose.

Supply laying jointing and testing LT XLPE and PVC insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 4 core complete all as specified

GI pipe light grade 50 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts etc with fixing clamps of required size, nuts, bolts, washers etc. fixed, complete all as specified.

R.K.ASSOCIATES (BID ID -3137587)