Construction of new 05 Bays TLF with allied electrical job, Laying of Pipelines from Pump House to TLF, Fixing of Existing Automation Equipments at TLF at Malda Depot under West Bengal State Office.

iii) 16 to 35 sq.mm XLPE / AYFY

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place.

i) All kinds of Soil

Extra for every additional lift of 1.5m or part thereof in excavation or banking excavated or stacked materials in all kinds of soil

Supply & filling coarse sand of Zone III in sand pad foundation in layers not exceeding 200mm.Each deposited layer shall be compacted by mechanical vibration and watering to achieve minimum relative density 95 %. Last layer of sand pad to be prepared in desired slope.

Brick on edge flooring with bricks of Class designation 7.5 on a bed of 12mm cement mortar including filing the joints with same mortar with common burnt clay non modular bricks

ii) cement mortar 1:6 (1 cement : 6 fine sand)

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying & curing, excluding the cost of centering, shuttering finishing including cost of curing, admixtures in recommended proportions as per IS:9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of engineer in charge, ALL WORKS UPTO PLINTH LEVEL. Less cement used as per design mix (if any) will be recoverable separately. No extra payment against extra cement if used shall be payable.

i) M-15 grade plain cement concrete (cement content considered @ 240 kg/cum

ii) M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work using cement content as per approved design mix manufactured in fully automatic batching plant & transported to site of work in transit mixer for all leads having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing & reinforcement including cost of admixtures in recommended proportions as per IS:9109 to accelerate/ retard setting of concrete, improve workability without impairing strength & durability as per direction of Engineer-in-charge (Note :- Cement content considered in this item is @ 330 kg/cum. Less cement used as per design mix (if any) will be recoverable separately. No extra payment against extra cement if used shall be payable.

i) M25 RMC for All works UP TO PLINTH LEVEL

ii) M25 RMC for All works ABOVE PLINTH UPTO FLOOR 5 LEVEL

Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth

i) Brick work in Cement mortar 1:4 (1 cement : 4 coarse sand) IN FOUNDATION AND PLINTH

Structural steel work riveted,bolted or welded in built up sections, trusses & framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Structural Steel Works: Supplying, transporting, fabricating, erecting Structural Steel work from rolled sections and built-up sections like flats, tees, angles, channels, plates, pipes, etc for various structural elements as required . Preparation of drawing, design & specification shall be arranged by contractor at his own cost as per guidance of IOCL. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2/St-3 ii. Primer: P4- Self Priming HB Epoxy Primer - One Coat, DFT 100-125µ iii. Intermediate Coat: U1- Polyamide cured HB Epoxy mastic coating - One Coat, DFT 100-125µ iv. Finish Paint: F1- Two Pack Acrylic Polyerethane (PU) - two Coats, DFT 50-60µ (2 coats of 25-30µ). Total min DFT 250µ The items include supply of paints and other required meterial, scafolding, labours, tools and tackles, etc. complete. The make of Structural Steel / tubular steel shall be of SAIL/ Tata/ RINL/ Jindal or equivalent as approved by EIC. In case some small Mild Steel sections are not manufactured by SAIL/Tata, steel of other manufactuer may be used which must confirm the relevant IS code with prior approval of Engineer-In-Charge.

Fabrication & Erection of IOC supplied structural steel work riveted, bolted or welded in single/ built up sections,trusses & framed work hoisting, fixing in position and applying a priming coat of approved steel primer all including cutting, complete

STRUCTURAL STEEL GRATING: Supplying, transporting, fabricating in factory, Electroforged rectangular gratings as per layout drawings with plain bearing bar and Cross Bars duly press locked into bearing bar by electrofusion. Gratings shall be duly hot dip galvanized after fabrication given in the detailed specification with minimum thickness of galvanising of average 85 microns all through the sectional area, & erecting in position and fixing in position mild steel Grating welded/ bolted/placed with adequate clamps wherevever applicable in floors, platforms, staircase steps, trench covers, landings etc. including cutting for openings wherever required as specified and directed at all floors at all levels etc. complete. The grating shall confirm to the typical section details of grating as shown in drawing . This works includes setting in position in Footpath/ Gutter/Drains/Floors to the required level and line over a bed of 20mm Average thick cement mortar (1:3). NOTE: The Grating shall be factory made, i.e. fabricated & Hot dip Gavanised in shop & transported to site for erection.

Providing & fixing hand rail of approved size, welding etc. to steel ladder railing,balcony railing & staircase railing and similar works including applying priming coat of approved steel primer.

iii) G.I. pipes

i) M.S. tube

Providing and fixing Klippon/Hi-rib Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) of Cold rolled steel confirming to IS:513-2008 of base metal thickness 0.50 mm, having Yield Stress of Min. 275 MPa. Steel surface shall have hot dip metallic coating of Al-Zinc alloy comprising 55% Alluminium, 43.5% Zinc and 1.5% Silicon as per the ASTM-A792M, with total mass of coating on both sides shall be 150 gms/sqm. The steel shall have organic coating with Silicon Modified Polyester (SMP) /Super Durable Polyester (SDP) paint on continuous coil coating line. The thickness of coating on top side shall be 20-25 Microns (i.e. 15-18 microns SMP /SDP paint over 5-7 microns epoxy primer) and back side 8-10 Microns SMP/SDP paint over epoxy primer. Total Coated Thickness (TCT) shall be 0.58 MM. Sheet shall have protective guard film of thickness of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 6m or as desired by Engineer-in-charge.

i) Profile Sheet for roofing

ii) Plain Sheet for Ridges (500 - 600mm).

iv) Plain Sheet for Gutter (600 mm over all girth)

Providing & fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work & fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels

ii) Thermo Mechanically Treated Bars of Fe- 500D grade or more, conforming to IS1786

Supplying and fixing MS foundation bolts with necessary GI nuts and washers of specified sizes,all conforming to relevant Indian Standards and as approved by Engineer-in-charge :

v) 25mm dia x 1000mm long with 100 mm dia x 8 mm thick plate

vi) 32mm dia x 1125mm long with 100 mm dia x 8 mm thick plate

Providing and laying cement plaster on surfaces with fine sand including curing etc.

v) 20mm Cement plaster of mix 1:4 (1 cement: 4 fine sand)

Centering and shuttering including strutting, propping etc. and removal of form for :

i) Foundations,footings,bases of columns, etc. for mass concrete

v) Columns, Pillars, Piers, Abutments, Posts and Struts.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand & manufacture on steel galvanised iron/steel

works

Providing Neat cement punning

Stone flooring with 18mm thick Marble/Granite stone (sample of stone shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry including rubbing and polishing complete

vi) Granite stone/Makrana White second quality in flooring

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, within premises and lift upto 1.5m

Carriage charge for disposal of earth by mechanical means, including loading, transporting, stacking, unloading to approved municipal dumping ground / unobjectionable place as per direction of Engineer- in-Charge beyond IOCL Premises for all leads and including all lifts.

iii) Distance > 3 km< 5 km

iv) Distance > 5 km< 10 km

vi) Additional charges per km beyond 20 km over item MPLCN02305

"GROUTING For grouting (As per Technical specification), cost of grouting, including supply of materials shall be covered in the unit rates.Rates shall include cost of labor, supervision, deployment of tools & tackles, consumables, materials and other associated arrangements required to execute all the related activities." Grouting using Free flow non shrinkable grout material CONBEXTRA GP-2 or approved equivalent below the bases of pumps/ pockets etc

Safety Harnesh

UNIVERSAL EXTREMITY PLATE-SS316 PN-4000

WIRE ROPE-SS316L ,8.0MM DIA, 7X19 PN9XX

TENSIONER WITH TENSION INDICATOR AND SWA

CABLE EXTREMITY-SS316 (8MMDIA) PN7000(0

SPRING TYPE SHOCK ABSORBER PN4000MU(02)

SET OF 2 NOS MOLDED STOPPER FOR AP016 FO

DOUBLE PULLEY WITH SS SHEAVES AP016

FULL BODY ADJUSTABLE HARNESS PN22(AS)

RETRACTABLE WIRE ROPE FALL ARRESTER BLOC

OVER HEAD WIRE ROPE LIFELINE PRIMARY IN

OVER THE HEAD WIRE ROPE ADDITIONAL ANCHOR

Swing Ladder-

Supply of Retractable stairs for Tank Truck

I/T/Commissioning of Retractable stairs

Designing, supplying, fabricating, welding, bolting, riveting, assembling and erecting in position 8.0 M high Fire Screen Wall around the tank with GI sheets with cross supports, etc (temporary required local) as per alignment shown by site Engineer, maintaining same till the completion of entire work and dismantling the entire screen wall, carting away the dismantled materials from site, redoing the entire existing surface to the original condition, etc complete.The 8M high Fire Screen Wall including the foundation is to be designed and approved by a ''Licensed Structural Engineer'' and should be suitable for local soil bearing capacity, wind speed, etc.

Erecting temporary Mobile Fire Screen Wall around the place where hot work is carried out using GI sheets or non-flammable asbestos sheets with required structurals or pipe fasteners. Payment will be made for total area of sheets provided. The screen needs to be moved from place to place at no extra cost. (If required dismantling and refixing of the same screen are also to be done with no extra cost). For simultaneous works at 2 or 3 points at a time, extra area may be considered as per site requirement.

Providing and laying in position approved quality profiled, pre-coated coloured galvanized steel sheets of minimum 0.45mm thickness (TCT) in barricading, including cost of all materials, delivery to site, cutting, metering, lapping, providing cut-outs for fixing accessories and necessary approved quality corrosion proof fasteners with neoprene capping and washers ridges, valleys, gutters, gutters of required shape, apron pieces, flashing etc. all complete and with all accessories required for the cladding works including necessary structural scaffolding for erection jobs as specified and directed. NOTE: (1) Contractor shall take back the cladding sheets (used in barricading structure) after completion of the job and on the instructions of Engineer-in-Charge. (Cost of dismantling and Carriage till contractor's store (outside the IOCL premises) is included in this item and no extra payment shall be paid to the contractor on this account). (2) Payment against the job on SQM basis shall be made to the Contractor while erection of the cladding sheets(3) The cladding sheets shall be dismantled and taken outside the premises by the Contractor within 30 days of instructions from E-i-C. (4) In case the Contractor fails to dismantle and shift the cladding material outside the IOCL premises within 30 days of clear instructions from E-i-C, the Owner shall be free to get the same dismantled and shift to Owner's scrap yard using Owner's resources and in such case the dismantled items shall not be returned to the Contractor and the ownership of the same shall be fully vested with the Owner

Demolishing cement concrete manually/ by mechanical means including disposal of material outside premises at an unobjectionable place as per direction of Engineer-in-charge.

i) 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing C.C./R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1000 m, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material outside premises at an unobjectionable place as / direction of Engg-in-charge

Dismantling Steel work in built up sections in angles, tees, flats channels etc. including all gusset plates, bolts nuts, cutting rivets welding etc. including dismembering and stacking within premises

Dismantling roofing including ridges, hips valleys & gutters, False ceiling of any type and stacking the material within premises, of:

i) G.S. Sheet/ Klippon galvalume sheet/ False ceiling panels

LAYING & WELDING OF PRODUCT PIPELINE (ABOVE GROUND) IN ZONE- B Laying and welding (3 runs minm.) Above Ground Pipelines from supplied MS pipes (pipes to be supplied anywhere within the depot and the contractor shall shift the same to the site of work at no extra cost with all leads and lifts) of the following sizes as described below, including cutting, bevelling and fixing the supplied specials such as elbows, bends, tees, reducers, etc complete and successful hydrotesting the pipeline at a pressure of 10.5 kg/cm2 for a minimum period of 4 Hrs. The job includes Dye Penetration (DP) testing of pipeline joints as per approved QAP. Above ground pipeline to be laid on concrete pedestals (which is to be constructed as per the respective item of this schedule)/ piperacks/ TLF shed/ pump house and manifolds and Painting the pipeline as per the specifications enclosed including the colour coding as per IOC specifications. Welding of pipeline should conform to Radiography quality. 10% of the joints shall be radiographed and the cost of the same will be paid separately as per respective item, etc. and as directed at site. Note: a. Any repairs to the defective welding shall be made good at no extra cost to IOCL. Re-radiography of repaired joint shall also be at contractor's cost. b. The rates quoted also to include Painting and colour coding of pipelines as per the standards. c. Painting Scheme : Application for External painting shall be carried out by means of AIRLESS SPRAY PAINTING SYSTEM only. 1. Surface Preparation : as per Sa 2½ 2. Primer : P3- Red Oxide Zinc phosphate Primer - 2 Coats (30-35µ each), DFT 60-70µ 3. Intermediate Coat : NIL 4. Finish Coat : F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total Min DFT 90µ

300 mm dia pipe

250 mm dia pipe

150 mm dia pipe

100 mm dia pipe

80 mm dia pipe

50 mm dia pipe

25 mm dia pipe

20 mm dia pipe

15 mm dia pipe

Radiography inspection on product pipe joints of all types and thickness including providing all necessary equipment required to perform the work as per our specification and direction of engineer-in-charge. The radiographs shall be submitted to the engineer in charge at site/ third party inspecting agency. Note: Retaking of radiography due to d

300 mm dia pipe

250 mm dia pipe

150 mm dia pipe

100 mm dia pipe

80 mm dia pipe

50 mm dia pipe

25 mm dia pipe

efective welds/ defective films/ defective workmanship, etc. will be at contractor's cost. For every failure, radiography has to be done for three additional joints of same dia. at contractor's cost.

Radiography inspection on product pipe joints of all types and thickness including providing all necessary equipment required to perform the work as per our specification and direction of engineer-in-charge. The radiographs shall be submitted to the engineer in charge at site/ third party inspecting agency. Note: Retaking of radiography due to d

300 mm dia pipe

250 mm dia pipe

150 mm dia pipe

100 mm dia pipe

300 mm dia Pipe

Radiography inspection on product pipe joints of all types and thickness including providing all necessary equipment required to perform the work as per our specification and direction of engineer-in-charge. The radiographs shall be submitted to the engineer in charge at site/ third party inspecting agency. Note: Retaking of radiography due to d

300 mm dia pipe

250 mm dia pipe

150 mm dia pipe

100 mm dia pipe

80 mm dia pipe

50 mm dia pipe

25 mm dia pipe

20 mm dia pipe

Provision of Saddle plates for Product & Hydrant Pipelines over pedestals including cutting and fabrication of saddle plates from IOCL supplied MS pipes and welding of the same on pipelines under pedestals with minimum 3 run of welding complete as per specifications, drawings and directions of Engineer in charge.

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

20 mm dia

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

15 mm dia

300 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

Making flanged joints between flanges (WNRF/SORF/BLRF) including supplying and fixing 3 mm thick SW SS gaskets with graphite fillers, studs, nuts, bolts of approved make for the following sizes, as per IOCL specifications and site instructions. The flanged joint shall also include providing and fixing multistrand copper wire/flat for bonding of product pipelines including provision of lugs wherever required.

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

Making flanged joints between flanges (WNRF/SORF/BLRF) including supplying and fixing 3 mm thk PTFE gaskets, studs, nuts, bolts etc. of approved make for the following sizes as per IOC specifications and site instructions. The flanged joints shall also include providing and fixing multistrand copper strip / flat for bonding of product pipelines. (for Ethanol)

Fixing & Installation of the supplied ROSOV / DBBV / MOV / GOGV / PLUG VALVE / CS GATE VALVE / QUARTER TURN VALVE / BALL VALVE of the following sizes on the pipeline including supplying and fixing 3 mm thick SW SS gaskets, studs, nuts, bolts, washers, etc of approved make for the following sizes as per specifications and site instructions. Note: The rate quoted for the above items should include: a. mechanical cleaning/greasing of the valves after erection. b. supplying and painting the valves / fittings, etc. with two coats of P3 (Red Oxide Zinc Phosphate Primer) and two coats of F4 (Synthetic Enamel Finish Paint) of approved colour and shade as per colour coding specifications for fittings on product pipelines / fire hydrant lines. c. Fittings on Ethanol service shall be provided with PTFE gaskets 3mm thk. d. Both the flanged joints shall also include providing and fixing multistrand copper strip / flat for bonding of product pipelines wherever required.

100 mm dia

80 mm dia

Installing the supplied Thermal Relief Valves (TRV) for the product pipeline and fixing the same on the pump discharge lines to TLF including painting the valves and connected piping with 2 coats of P3 (Red Oxide Zinc Phosphate Primer) and 2 coats of F4 (Synthetic Enamel Finish Paint) of approved colour and shade as per the directions of site engineer. Note: a. The 20 / 25 mm dia piping connected to the TRVs shall be measured and paid separately under respective items. b. The job also includes providing and fixing 8SWG copper wire bonding for the flange joints of the assembly.

Fixing the supplied Class-150 CS Non Return Valves (NRV - swing check / lift ) for product and fire hydrant pipelines as per enclosed specification & drawings. NRVs shall be mechanically cleaned (St-2) & painted with 1 coat of P4 (Self Priming HB Epoxy mastic coating) and 2 coats of F1 (Two Pack Acrylic Poly-Urethane) of approved colour and shade as per specifications and as per directions of site in charge. Rate is also inclusive of bonding with multi-strand Cu strips/flat.

25 mm dia Class-800

250 mm dia

150 mm dia

15 mm dia Class-800

100 mm dia

80 mm dia

Laying and welding (min 3 runs) of AG & UG Pipeline (GI IS-1239 Gr-C / MS IS -1239 Gr-C pipes) for pneumatic / service water / DG Set & Fire Pump Fuel Piping Systems following sizes of pipes at all places inside the IOCL Location. Note: a) Painting of AG & UG piping will be paid separately b) AG piping shall also be suitably supported on the CC pedestals as per designed spacing, etc., & the same will be paid separately. c) Excavation & civil works for UG piping will be paid separately.

65 mm dia

SUPPLY ITEMS: FOR PIPELINE WORKS

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

Supply of MS Pipes

SUPPLY OF MS PIPE: IS-1239 Gr. C Heavy Duty

Supply (Class-800) CS Gate Valve for pressure relief lines as per enclosed specification : Gate Valve API 602 CL800 SWE Bltd Bonnet Handwheel Operator A105 Trim 8 to API 600 602 (13% Cr Hard faced Seat) OS&Y Graphite Gland Packing API 598 Solid Wedge

25 mm dia

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

20 mm dia

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

Supply of following Slip On FLANGES (SORF) conforming to Material: A-105, END-RF/125AARH As per ASME B16.5

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

SUPPLY OF MS PIPE: IS-1239 Gr. C Heavy Duty

Supply of following Weld Neck type Flanges conforming to ASTM A- 105 Class 150; ANSI B 16.9

Supply of the following Blind Raised Face Flanges (BLRF) conforming to ASTM A-105 Class 150; ANSI B 16.5

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

150 mm dia

100 mm dia

80 mm dia

Supply of Thermal Relief Valves (TRV) as per specifications: Inlet 20 mm x Outlet 25 mm

RE-PAINTING OF PRODUCT PIPELINE / FIRE HYDRANT PIPELINE IN ZONE- B : Painting of External surface including color coding of Mild Steel above ground Pipeline & Fittings such as valves, flanges, etc. as per the attached technical specification and direction of Site Engineer. Item also includes painting of structural surface as per the following painting scheme: i. Surface preparation: St-2 / St-3 ii. Primer: P3- Red Oxide Zinc Phosphate Primer - Two Coats, DFT 60-70µ (2 coats of 30-35µ) iii. Finish Paint: F2- Aluminium Finish Paint - 2 Coats (15-20µ each), DFT 30-40µ Total min DFT 90µ The items include supply of paints and other required material, scafolding, labours, tools and tackles, etc.

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

150 mm dia

100 mm dia

80 mm dia

PIPE FITTINGS : Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD or as required based on connecting pipeline thickness as per ASME B 16.5. Generally pipelines 16" and above- thickness is 7.14 mm, Pipelines dia 6" to 14" - thickness is 6.35 mm, Pipelines 4" and below 4.78 mm. 90 Deg LR ELBOW (1.5D)

150 mm dia

100 mm dia

PIPE FITTINGS : Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD or as required based on connecting pipeline thickness as per ASME B 16.5. Generally pipelines 16" and above- thickness is 7.14 mm, Pipelines dia 6" to 14" - thickness is 6.35 mm, Pipelines 4" and below 4.78 mm. Note: The quantities given are only indicative.The actual quantities to be supplied will be based on the finalised drawing for pipeline routing. 45 Deg LR ELBOW (1.5D)

PIPE FITTINGS : Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD or as required based on connecting pipeline thickness as per ASME B 16.5. Generally pipelines 16" and above- thickness is 7.14 mm, Pipelines dia 6" to 14" - thickness is 6.35 mm, Pipelines 4" and below 4.78 mm. Note: The quantities given are only indicative.The actual quantities to be supplied will be based on the finalised drawing for pipeline routing. EQUAL TEE

PIPE FITTINGS : Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD or as required based on connecting pipeline thickness as per ASME B 16.5. Generally pipelines 16" and above- thickness is 7.14 mm Pipelines dia 6" to 14" - thickness is 6.35 mm, Pipelines 4" and below 4.78 mm. Note: The quantities given are only i

ndicative.The actual quantities to be supplied will be based on the finalised drawing for pipeline routing. UNEQUAL TEE

300 x 300 x 100 mm (HSD)

250 x 250 x 100 mm (MS)

150 x 150 x 100 mm (SKO)

150 x 150 x 50/80 mm (Ethanol)

PIPE FITTINGS: Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD/ as mentioned and dimensions as per ASME B 16.5. REDUCERS (CONCENTRIC)

150 NBX 100 NB, 5.4MM X 4.8MM thickness

Welding of the supplied CS WNRF Flanges on the pipelines with 1 run weld inside and two runs weld outside, etc complete and as per specifications enclosed. BW, WNRF Flange SCH-40 require minimum 3 runs, which is equivalent to 3 runs FW, for SORF Flange. In addition, root weld is to be grinded to sound metal

300 mm dia

250 mm dia

150 mm dia

100 mm dia

100 NBX 80 NB, 4.8MM X 4.8MM thickness

80 mm dia

25 mm dia

Supply of Cast Carbon Steel ASTM - A 216, Gr. WCB Double Flanged Gate Valve as per BS : 1414; API-600, Class # 150, with stainless steel rising spindle & internal working parts, flange drilled as per ANSI B 16.5 Cl # 150, raised face and hand wheel including making flanged joints at both ends with SW SS gaskets, supply & fixing of nuts, bolts, etc. all complete in all respect as per the direction of engineer-in- charge.

80 mm dia

25 mm dia

300 mm dia

25 mm dia

Supply, handling, cutting, edge preparation, fabrication, welding, erection (under ground or above ground), supporting, testing & commissioning of Stainless Steel (SS) Pipe IS:316 marked, schedule-40, including supply & welding of all necessary S.S. fittings such as elbow, reducer, tee, nipple, socket, etc. and S.S. Flanges with S.S. nuts & bolts, gaskets & washers, U-bolts, etc to complete the work in all respect as per the direction of engineer-in- charge.

Supply, handling, erection, testing & commissioning of Female Screwed (BSPT) lever-operated Stainless Steel Ball Valve suitable for handling corrosive liquid. The valve should have S.S. body- ASTM A 351 CF 8M, Ball & stem AISI 316, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Supply, handling, erection, testing & commissioning of Stainless Steel Female Screwed (BSPT) horizontal type Non-Return Valve (NRV) / Check Valve with all S.S. internals, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Handling, transportation, installation, erection, testing and commissioning of AIR ELIMINATORS of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Supply, handling, erection, testing & commissioning of Female Screwed (BSPT) lever-operated Stainless Steel Ball Valve suitable for handling corrosive liquid. The valve should have S.S. body- ASTM A 351 CF 8M, Ball & stem AISI 316, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Supply, handling, erection, testing & commissioning of Stainless Steel Female Screwed (BSPT) horizontal type Non-Return Valve (NRV) / Check Valve with all S.S. internals, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Inlet / Outlet : 80 mm dia

Supply, handling, erection, testing & commissioning of Female Screwed (BSPT) lever-operated Stainless Steel Ball Valve suitable for handling corrosive liquid. The valve should have S.S. body- ASTM A 351 CF 8M, Ball & stem AISI 316, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Inlet / Outlet : 50 mm dia

Handling, transportation, installation, erection, testing and commissioning of STRAINERS of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Handling, transportation, installation, erection, testing and commissioning of PD METER of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Supply, handling, erection, testing & commissioning of Female Screwed (BSPT) lever-operated Stainless Steel Ball Valve suitable for handling corrosive liquid. The valve should have S.S. body- ASTM A 351 CF 8M, Ball & stem AISI 316, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Supply, handling, erection, testing & commissioning of Stainless Steel Female Screwed (BSPT) horizontal type Non-Return Valve (NRV) / Check Valve with all S.S. internals, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Handling, transportation, installation, erection, testing and commissioning of TURBINE FLOW METER of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Supply, handling, erection, testing & commissioning of Female Screwed (BSPT) lever-operated Stainless Steel Ball Valve suitable for handling corrosive liquid. The valve should have S.S. body- ASTM A 351 CF 8M, Ball & stem AISI 316, seat test pressure 10 kg/sq.cm. The job includes the supply & fittings of all necessary S.S. fittings required to complete the job in all respects as per the direction of the engineer-in-charge.

Inlet / Outlet : 40 mm dia

Handling, transportation, installation, erection, testing and commissioning of DIGITAL CONTROL VALVE of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Handling, transportation, installation, erection, testing and commissioning of LOADING ARM of following sizes on the pipeline including supplying & fixing metallic gasket, studs & bolts, etc (as per piping material specification: 9224:0000-PIPHNS-00001.) Note: The rate quoted for the item shall include supplying and painting color coding as per IOCL specification.

Supply of CS, ASME B36.10, API- 5L Grade-B, BE, ERW Pipeline as per specification and direction of IOCL for product service. The item to be executed with prior approval from Engineering Department.

150 mm NB, Wall Thickness 6.35

STEEL PIPES, Material: IS1239 Part-I, Black pipe,Thick Heavy

15 mm dia,Sch 40

20 mm dia, Sch 40

PIPE FITTINGS: Supplying the following sizes of Elbows/ Tees/ Reducer made of carbon steel seamless pipes with bevelled ends as per enclosed specifications for the following sizes. Note: The fittings shall be as per ASTM A 234 Grade WPB schedule STD/ as mentioned, and dimensions as per ASME B 16.5. REDUCERS (CONCENTRIC)

150 NB x 100 NB 6.35 MM x 4.8 MM thickness

100NB x 80 NB, 4.8 MM x 4.8 MM thickness

Supply, fabrication, and laying of SS pipes of the following sizes, confirming to material ASTM A312 TP 304 , SCH 40 Seamless with plain end, confirming to dimension ASME B36.19. Job include cutting, bevelling and fixing the supplied specials such as elbows, bends, tees, reducers, etc, complete and successful hydrotesting the pipeline wherever required at a pressure of 10.5 kg/cm2 for a minimum period of 4 Hrs.

150 NB x 100 NB 6.35 MM x 4.8 MM thickness

100NB x 80 NB, 4.8 MM x 4.8 MM thickness

Supply of the following SS Socket weld, RF, Flange, 125 AARH as ASTM A182 Gr F 304, DIM. ASME B16.5 Class 150

Supply of Forged WNRF SS 304 CLASS-150

Supply of the following SS Socket weld, RF, Flange, 125 AARH as ASTM A182 Gr F 304, DIM. ASME B16.5 Class 150

Supply of the following SS Socket weld, RF, Flange, 125 AARH as ASTM A182 Gr F 304, DIM. ASME B16.5 Class 150

Supply of the following SS Raised Face BLRF, 125 AARH as per ASTM A182 Gr. F304L DIM. ASME B16.5 Class 150

Supply of 90 Degree SS304 40 S L.R. Elbow (1.5D)

Supply of TEE SS 304

25 NB x 25 NB x 25 NB

25 NB x 25 NB x 15 NB

SS BALL VALVES

15 NB, 150#, FLG, BODY ASTM A351 CF8M / SS316,TRIM SS3316, BS EN ISO 17292

20 NB, 150#, FLG, BODY SS316,TRIM SS3316

50 NB, 150#, FLG, BODY ASTM A351 CF8M / SS316,TRIM SS3316, BS EN ISO 17292

150 NB x 100 NB 6.35 MM x 4.8 MM thickness

Procurement & Supply of Needle valve

20 NB, 150#, FLG

Fixing of supplied CS Gate / Ball valves / Check Valves / Needle Valve. PRODUCT PIPELINE Fixing shall include supplying and fixing of Metallic Spiral Wound gaskets (for size 50 mm dia. and above100% spare quantity of metallic spiral wound gasket to be supplied) confirm to SS316 with Graphite fill as per ASME B16.20, nuts & stud bolts confirm to ASTM A194-2H & ASTM A193B-7 respectively.The flange joint shall also include fabrication , drilling holes of suitable bolt size and fixing of CU strip for bonding of joint, cost of supply of CU strip has been taken separately in respective item."

vi) 3 Core x 1.5 sq.mm Copper Cable FRLS

CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, trenches, fabricated tray supports etc will be covered & paid in Separate Items

iv) 3 Core x 2.5 sq. mm Copper Cable FRLS

xii) 4 Core x 6 sq. mm Aluminium Cable FRLS

FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination(FLP):Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of FLP heavy duty double compression cable glands, Baliga/CEAG-FCG /Flexpro/ FEPL make, crimping lugs and allied jointing materials, etc. all complete as per specification & direction of Engineer In-charge. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used.

vi) 3 Core x 1.5 sq. mm.

vii) 3 Core x 2.5

Supply & fixing of flame proof junction box (4 way entry) of BALIGA /CEAG-FCG/FLEXPRO/FEPL make including clamping arrangement, all complete as per specification and direction of Engineer In-charge.

PROVISION OF EARTHING

xii) 4 Core x 6 sq. mm

Supplying, fabricating and installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling and/or fix to steel/RCC columns, beams or any other structure members with MS suspenders, angles, channels, etc complete as per the direction of IndianOil

i) 150mm x 75mm x 2mm

v) 25 x 3 mm GI strip

ii) 300mm x 75mm x 2mm

Providing earthing with 100 mm dia, 3.8M long C.I/GI pipe as per IS:3043 (with latest ammendment) including providing suitable earth bus for interconnection, providing a mixture of salt & charcoal, making earth pit chamber with chequered plate cover as per standard Drawing all complete as per specification & direction of Engineer In-charge

Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and lightning protection under or aboveground complete as per specification for the following :

iii) 50 x 6 mm G.I. Strip

vi) 8 S.W.G. G.I. Wire (bare)

xiii) 25 x 5 mm Cu. Strip

i) 6A to 32A SP MCB

Formation of lighting protection arrangement with supply of 1.0 M height spike and erection at top most portion of structure/building and connecting the same to earthpit by 40x6mm GI strip (excluding supply and laying of GI strip)

Supply & fixing of 30mA RCCB of approved Make of following ratings:

iv) 4 poles, 40A

MINIATURE CIRCUIT BREAKERS (MCB) Supplying & fixing of Miniature Circuit Breakers as per approved make of 10KA Breaking cpacity of following ratings

MCB DISTRIBUTION BOARD INCLUSIVE OF SINGLE PHASE MCB Supply & fixing of MCB Distribution Board double door type, IP-42, inclusive of MCB, Single Phase, as per approved make of following types with all accessories such as tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs, etc. (MCB - 10KA Breaking Capacity)

i) 8way DB with 32ADP as incoming-1No.& 6 to16A SP as outgoing-8Nos

Supply and fixing of 100 W LED (Light Emitting Diode) light fixture with fittings and accessories for Yard lighting purpose having IP66 protection class with Pressure Die Cast LM6/ADC12/LM24 housing and with toughened glass or UV stabilized polycarbonate cover type of approved make or equivalent as per direction of Engineer-in-charge. The LED driver shall have an in-built high voltage cutoff >= 290 V with power factor of complete fitting greater than 0.90. CCT (Correlated Colour temperature) shall be in the range of 5665 K +/- 355 K as per ANSI standard C78.377, CRI (Colour rendering index) should include all colour range from R1 to R15 and > 70 for outdoor luminaire. LED efficacy shall be greater than 140 lumens/watt @ 350mA drive current. The minimum system lumen efficacy of the luminaire shall be 100 Lumens per Watt. The Surge Protection Device (SPD) should be series type with fail safe, surge protection for minimum 3kV shall be provided. Supply of complete fitting with all accessories as per specification attached and as per direction of engineer in charge. Each lot of fittings shall accompany test certificates LM79/ IS:16106 and reference/ batch nos of LEDs and fittings for verification at site. The supply of LED lighting shall be covered by a warranty of minimum 60 months from the date of supply of the lighting and the LED light fitting shall be complete in all respects including LED, LED Driver, Electronic circuitory, Luminaire etc.

Supplying and of 1C x 6 Sq. mm FRLS Flexible copper insulated green wire for earthing instruments as per specification.

LIGHTNING PROTECTION SYSTEM

"Supply & laying / installation of 25 x 3 mm GI strip (Galvanisation is 610 gms/sq. mtr. or as per IS-4759/ISO 1461) as horizontaland down conductor for Lightning protection system to be laid on on wall/ on RCC column/ steel structure/ curb/ roof including jointing by welding, connecting to equipments, painting to welded portion by black bitumen paint. The rates shall be inclusive of hardware required for clamping of earth strip, jointing the strips, test link etc. Cost of insulators for the support of the system as perdirection of Site In-Charge is included. As per IEC62305."

75 x 6 mm GI Strip

Fixing of supplied CS Gate / Ball valves / Check Valves / Needle Valve. PRODUCT PIPELINE Fixing shall include supplying and fixing of Metallic Spiral Wound gaskets (for size 50 mm dia. and above100% spare quantity of metallic spiral wound gasket to be supplied) confirm to SS316 with Graphite fill as per ASME B16.20, nuts & stud bolts confirm to ASTM A194-2H & ASTM A193B-7 respectively.The flange joint shall also include fabrication , drilling holes of suitable bolt size and fixing of CU strip for bonding of joint, cost of supply of CU strip has been taken separately in respective item."

Supply & installation / fixing of Test link (for connection of each down conductor to earth pit) as per attached drawing

Supply & installation of 1000mm long,20 dia. GI air termination rod (lightning rod) with all fixing material, rod) with all fixing material, accessories.

"LIGHTING FIXTURES FOR HAZARDOUS AREA (FLAMEPROOF TYPE)Supply of Flameproof, Ex""d"" suitable for Gas group IIA/IIB, T3, suitable for Zone 2, Weather proof LED Lighting Fixtures, lamps & Accessories as per attached specifications / data sheet (All Lighting fixtures shall be provided with required no. of double compression nickle plated brass cable glands, lugs and stopping plug.)"

40W LED, Well glass luminaire suitable for Ceiling/Pole/Structure/MS bracket/Rod/Pipe mountings enclosure, SS wire guard, stainlesssteel hardware, earthing terminal, installation hardware and all necessary accessories wired up to terminal box.

iii) 3 Core x 1.5 sq. mm. (copper)

xvi) 3.5 Core x 25 sq. mm Aluminium Cable FRLS

xxxvii) 36C x 1.5 sqmm Copper Cable FRLS

Supplying and laying of FRLS Armoured Copper Signal cable as per tender specifications.

i) 1P x 1.5 sqmm

ii) 2P x 1.5 sqmm

v) 4P x 1.5 sqmm

vi) 6P x 1.5 sqmm

vii) 8P x 1.5 sqmm

Supplying and laying of FRLS Armoured Copper Control cable as per specifications.

i) 2C x 1.5 sqmm

iii) 4C x 1.5 sqmm

v) 8C x 1.5 sqmm

viii) 18C x 1.5 sqmm

xi) 36C x 1.5 sqmm

Supplying and laying of FRLS Armoured Copper Power cable as per specifications.

i) 3C x 2.5 sqmm

Supply of Exd/FLP Junction Box (Power/Control/Signal JB) with IP 65 as per specification suitable for hazardous area of zone 1, group IIA/IIB, T3 or better having CCOE/CMRI approval. It shall be complete in all respect. Accessories like certified double compression cable glands with PVC shrouds & plugs for excess entries, SS 316 engraved tag plate, mounting clamp & SS 316 fasteners. Complete as per specification / tender documents.

12 ways JB

xi) 36C x 1.5 sqmm

Supplying and laying of FRLS Armoured Copper Power cable as per specifications.

i) 3C x 2.5 sqmm

Supply of Exd/FLP Junction Box (Power/Control/Signal JB) with IP 65 as per specification suitable for hazardous area of zone 1, group IIA/IIB, T3 or better having CCOE/CMRI approval. It shall be complete in all respect. Accessories like certified double compression cable glands with PVC shrouds & plugs for excess entries, SS 316 engraved tag plate, mounting clamp & SS 316 fasteners. Complete as per specification / tender documents.

8 ways JB

6 ways JB

4 ways JB

Installation of Exd/FLP Junction Box (Power/Control/Signal JB) with IP 65 as per specification suitable for hazardous area of zone 1, group IIA/IIB, T3 or better having CCOE/CMRI approval. It shall be complete in all respect. Accessories like certified double compression cable glands with PVC shrouds & plugs for excess entries, SS 316 engraved tag plate, mounting clamp & SS 316 fasteners. Complete as per specification / tender documents.