SPECIAL REPAIRS TO BLDG NO T-01 AND T-02 AND EXISTING GUARD ROOM BUILDING P- 07 AT INS UTKROSH AND OTHER SANCTIONED WORKS UNDER GE MINNIE BAY PORTBLAIR

Amount

Taking down cement plaster of any description on brick or stone walls or concrete surfaces, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer in Charge.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed by Engineer in Charge.

Taking down existing chowkats or frames n.exc. 1.5 Sqm each, handing over to contractor on account of Schedule of credit complete all as specified and as directed by Engineer in Charge.

Taking up or down old/chocked water tubings 15mm bore with fittings from trenches /walls removing for credit to contractor complete all as specified and as directed by Engineer in Charge.

Taking up or down old/chocked water tubings 20 mm bore with fittings from trenches /walls for credit to contractor complete all as specified and as directed by Engineer in Charge.

Material and labour for APP modified waterproofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface and then providing 10mm screed bed with water proofing compound with required slope complete as directed :- (a) Applying bituminous primer @ 1.2 kg/Sqm on the prepared dry roof surface. (b) Laying 4mm thick APP membrane Plain finish weight not less than 3 to 4 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap.(c) Applying bituminous primer @ 1.2 kg/Sqm and applying one coat of bituminous aluminium paint at the rate of 0.3kg/sqm Note : (i)The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane only. (ii)Necessary Manufacturer test certificate shall be submitted along with RAR/FB duly signed by Engineer-in-Charge and contractor.

M&L for disconnecting existing tanks, setting aside (or lowering if required) for hoisting if required reconnecting and refixing in position complete all as specified and as directed by Engineer in Charge.

S & F in repairs Aluminium anodised (minimum anodisation is 50 microns) sections in door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing,anodised aluminium snap beading, screws, handles, locking arrangements etc.,complete all as specified and as directed by Engineer-in-charge. (Note:- Weight of aluminium sections handles,butt hinges and locking arrangements shall be considered for payment. However cost of rubber packing shall be deemed to be included in the quoted rate. Glass panels, prelaminated particle boards, glass & aluminium wire cloth as applicable will be measured and paid separately as supplied only.

Supply only 5 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer in Charge.

Supply and fix for 12mm thick Prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work complete all as specified and as directed by Engineer in Charge.

Supply only aluminium anodised 'XPM' of size 3.00 x 1.5mm x 22 Gauge for mosquito proofing complete all as specified and as directed by Engineer in Charge.

M&L for rendering 10mm thick on fair faces of block masonry/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed by Engineer in Charge.

M&L for rendering to ceiling in 5mm thick on fair faces concrete surface in CM (1:3) finished even and smooth without using extra cement complete all as specified and as directed by Engineer in Charge.

M&L for external rendering 5mm thick in CM 1:4 with water proofing compound (water proofing compound shall be used as per manufacturer's instructions) over a coat of 10mm thick in CM 1:6 over brick or concrete surfaces finished even and fair complete all as specified and as directed by Engineer in Charge.

Supply only water proofing compound conforming to IS-2645,1975 complete all as specified and as directed by Engineer in Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer including complete all as specified and directed by Engineer - in -Charge.

All as per Item No: 16 but on ceiling complete all as specified and directed by Engineer - in -Charge.

M&L for preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion based premium quality matt finish exterior antifungal paint over a coat of alkali resistant primer all as per manufacturer's instructions complete all as specified and directed by Engineer - in -Charge.

M & L for 7 mm to 8 mm thick [Square or Rectangular] Non Skid Ceramic Tiles, Coloured, of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engineer - in -Charge.

All as per item No 19 here in before, but on vertical surfaces including 10mm thick CM 1:3 as in backing coat of dado/skirting complete all as specified and directed by Engineer - in -Charge.

M & L for 7 mm to 8 mm thick [Square or Rectangular] Non Skid Ceramic Tiles, Coloured, of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer Cement Mortar 1:6 complete all as specified and directed by Engineer - in -Charge.

M&L Coloured Glazed ceramic tiles in vertical surfaces350X250X7mm/ 450X350X 7mm thick as in skirting /dado, set and jointed in cement slurry and pointed in coloured cement to match laid over 10mm thick cement backing coat in CM 1:3 complete all as specified and directed by Engineer - in -Charge.

M & L for vitrified ceramic tiles 10 mm thick Coloured, double charged of size not exceeding 0.36 [Square or Rectangular] as in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and directed by Engineer - in -Charge.

All as per item No.23 here in before, but on vertical surfaces including 10mm thick CM 1:3 as in backing coat of dado/skirting complete all as specified and directed by Engineer - in -Charge.

M&L For Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including polishing complete all as specified and directed by Engineer - in -Charge.

M & L for 300 x 300 x 10mm thick coloured heavy duty vitrified exterier chequered tiles as in floor/wall set and jointed in cement slurry and pointed in coloured cement to match laid over 15mm thick cement mortar in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube as per manufacturer's specification & drawing complete all as specified and directed by Engineer - in -Charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing including necessary butt hinges, tower bolt etc complete all as specified and directed by Engineer-in-Charge.

S & F 100 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and directed by Engineer - in -Charge.

S & F 150 mm long Aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed by Engineer - in -Charge.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and directed by Engineer - in -Charge.

S&F stainless steel friction stay hinges of standard size complete all as specified and directed by Engineer - in -Charge.

M&L complete removal of existing wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed by Engineer - in -Charge.

All as per Item No: 33 but on ceiling including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

M&L for preparation of old painted surface of wall and applying one coat of acrylic emulsion weather coat premium quality antifungal exterior emulsion complete all as specified and directed by Engineer - in -Charge.

M&L for new or previsouly untreated Surfaces of any description over 10cm girth or width and applying two coats of synthetic enamal paint over one coat of pink primer complete all as specified and directed by Engineer - in -Charge.

S&F in repair for 18 mm thick HDF high quality boardings one side pre laminated (white) and other side plain to receive decorative laminates as in kitchen cabinet /shelves /wardrobe /wall panelling fixing with necessary small fitting as required as per manufacturers instructions complete all as specified and directed by Engineer - in -Charge.

M&L for second class hard wood for wooden beading , cupboards / shelves / wardrobe / wall paneling exc 6sqcm & not exc 13 Sqcm complete all as specified and directed by Engineer - in -Charge.

S&F 100 mm brass handles , cast type , polished bright complete all as specified and directed by Engineer - in -Charge.

S&F 100mm long hasp and staples mild steel wire type stove enamelled black including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F 30mm width continuous (piano) hinges mild steel finish or electrogalvanised complete all as specified and directed by Engineer - in -Charge.

S&F Teak wood lipping frame 6 mm thick for 18/ 19 mm width fixed with nails/ screws complete all as specified and directed by Engineer - in -Charge.

S&F second class hard wood for plain , solid , straight , chowkats and frames , wrought , framed reabeated the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer - in -Charge.

S&F Magnet catch for cup boards of brass body and skirting plate complete all as specified and directed by Engineer - in -Charge.

S & F Mild steel work in tubular /post/trusses/purlin including special shaped washers base and bed plate cleat nut and bolt etc confirming to IS 1161- 1979 graded St 240 complete all as specified and directed by Engineer - in -Charge.

M&L for mild steel work in Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) completely all as specified and as directed by Engineer in Charge.

S&F in repairs curtain rod / harrison rails mild steel chromium plated with fixed brackets , stops, rollers etc, 25 mm dia with fixed brackets , stops rollers etc complete all as specified and directed by Engineer - in -Charge.

S&F in repairs brackets mild steel chromium plated suitable for curtain rod 25 mm dia complete all as specified and directed by Engineer - in -Charge.

Supply and fixing 15mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete all as specified and directed by Engineer - in -Charge.

All as per item no 49 above but 20 mm bore complete all as specified and directed by Engineer - in -Charge.

Supply and laying of CPVC pipes 32mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer - in -Charge.

Supply and fixing of CPVC Brass Elbow 16 mm outer dia complete all as specified and directed by Engineer - in -Charge.

Supply and fixing of CPVC Brass Tee 20mm outer dia complete all as specified and directed by Engineer - in -Charge.

Supply and fixing of CPVC Brass Elbow (3/4 X ½) 20mm outer dia complete all as specified and directed by Engineer - in -Charge.

S & F in repairs two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed by Engineer - in -Charge.

S&F in repairs chromium plated health faucet with 1000mm PVC pipe for 15 mm bore with fittings complete all as specified and directed by Engineer - in -Charge.

S & F in repair Bib Taps, long body with flange cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed by Engineer - in -Charge.

S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to steel pipe or union, complete all as specified and directed by Engineer - in -Charge.

S & F in repairs Angular cock 15 mm dia, cast copper alloy with capstan head, screwed down high pressure with long shank and cup fancy type for iron pipe etc complete all as specified and directed by Engineer - in -Charge.

S&F in repair Corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer - in -Charge.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern) EWC white in colour with and including plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device including connection to outgoing pipe and flushing pipe complete all as specified and directed by Engineer - in -Charge.

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including 32mm brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, etc complete all as specified and directed by Engineer - in -Charge.

S&F in repairs 20 mm brass chromium plateds towel rail of 20mm dia and 600mm in length 'D' shaped between flanges complete all as specified and directed by Engineer - in -Charge.

S&F in repairs for powder coated aluminum peg set of 4 solid body complete all as specified and directed by Engineer - in -Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer - in -Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and directed by Engineer - in -Charge.

S&F Aluminium wind ties for roof including all necessary drilling, bolting or rivetting fixed with GI self tapping screws complete all as specified and directed by Engineer - in -Charge.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces of any description, over 10 cm width or girth, not otherwise described including preparing new steel surfaces complete all as specified and directed by Engineer - in -Charge.

M&L for TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing clips complete all as specified and directed by Engineer - in -Charge.

All as per item No 70, but 6 mm to 8mm dia for stirrups complete all as specified and directed by Engineer - in -Charge.

M&L for form work for lintel, chajjas, slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer - in -Charge.

M&L for Reinforced cement concrete 1:2:4 Nominal mix type B-2 using 20 mm graded stone aggregate in Chajjas, slabs and similar type of work complete all as specified and directed by Engineer - in -Charge.

M&L precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed by Engineer - in -Charge.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer - in -Charge.

M&L for 75mm thick Plain Cement Concrete 1:3:6 Nominal mix type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and directed by Engineer - in -Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness in roof covering, etc. including ridge complete all as specified and directed by Engineer - in -Charge.

Dismantling wrought iron or mild steelwork of any description not otherwise provided for complete all as specified and directed by Engineer - in -Charge.

S&F Mild Steel Rolled sections as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engineer - in -Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engineer - in -Charge.

S&F of aluminium anodised snap grid false ceiling of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, grid size n.exc. 610 x 610mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab roof truss fixed with suitable size MS hook and fastening bolts etc including 'E' board classic 4mm thick oceanic sheet of size n.exc. 610 x 610mm size fixed in ceiling with clips to aluminium snap grid incl preparation of new surface and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engineer - in -Charge.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) complete, fitting such as switches ceiling roses, pendants, regulators, Sockets etc removing unserveciable materials at site and making good disturbed surface to match with existing finish complete all as specified and directed by Engineer - in -Charge.

Taking down carefully copper/aluminium Sub main wiring any size from surface/concealed conduit / PVC casing of any height and removing unserviceable materials at site and making good of disturbed surface to match with existing finish complete all as specified and directed by Engineer - in -Charge.

M&L for point wiring with 1.5 Sqmm (nominal area) FRLS, single core PVC insulated 650/1100 Volts, grade multistranded FRLSH copper conductor unsheathed in and including concealed PVC conduit/PVC casing & caping 20 mm dia or higher and conduit fittings and accessories including one green colour 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLS grade as earth wire up to common earth and connected to earth dolly including 1.2mm mild steel terminal box with top laminated sheet complete for the following:-

One light /fan/bell point controlled by one 05Amps switch complete all as specified and directed by Engineer - in -Charge.

One 5/6 Amps socket point on independent board controlled by one way switch complete all as specified and directed by Engineer - in -Charge.

One three pin switch socket 5/6 Amps plug point on same board complete all as specified and directed by Engineer - in -Charge.

All as per item No.84 here in before but with 2.5 Sqmm single core multi stranded FRLSH copper conductor for one three pin socket 15/16 Amps on independent board including continuous earth wire PVC insulated 2.5 Sqmm multi stranded FRSLH copper conductor to common earth dolly complete all as specified and directed by Engineer - in -Charge.

All as per item No.84 here in before but with 4 Sqmm single core multi stranded FRLSH copper conductor for one three pin socket 15/16 Amps on independent board including continuous earth wire PVC insulated 4 Sqmm multi stranded FRSLH copper conductor to common earth dolly complete all as specified and directed by Engineer - in -Charge.

S&F socket outlet 2/3 pin 5 Amps 240 volts flush type complete all as specified and directed by Engineer - in -Charge.

S&F socket outlet 3 pin 5/15 Amps 240 volts flush type complete all as specified and directed by Engineer - in -Charge.

S&F one way switch 5/6 Amps 240 volts flush type complete all as specified and directed by Engineer - in -Charge.

S&F one way switch 15/16 Amps 240 volts flush type complete all as specified and directed by Engineer - in -Charge.

S&F bell Push 5/6amps 240 volts flush type complete all as specified and directed by Engineer - in -Charge.

Supply and fix in replacement of Fan regulator,stepped type 120W - 1/2 module ,220V 50Hz complete all as specified and directed by Engineer - in -Charge.

S&F in replacement of ceiling rose, surface bakelite 65 mm x 30 mm, 3 terminals complete all as specified and directed by Engineer - in -Charge.

Supply and fix in replacement of vertical Distribution board TPN 4way IP 43 IK-09 with metal double door suitable for Provision of MCB , 36 KA 63 Amp for housing of MCBs complete all as specified and directed by Engineer - in -Charge. Note : Sheet metal enclosure for MCB distribution board shall be fixed in the wall such that front cover shall be seen flush with the wall surface.

S&F in replacement of Distribution board SPN 8 way with category of protection double door type IP-42 factory made with tinned copper 200 Amps rated bus bar suitable for MCBs,all as specified and directed. Note : Sheet metal enclosure for MCB distribution board shall be fixed in the wall such that front cover shall be seen flush with the wall surface.

S&F in replacement of MCB TPN 40 to 63 Amps, 440 Volts, 10 kA, 'C'Curve complete all as specified and directed by Engr-in-Charge.

S&F in replacement of MCB Double Pole 32 Amps working on 415 volts 50 Hz AC supply,10 KA C series complete all as specified and directed by Engr-in-Charge.

supply and fix in replacement of MCB single pole 6 to 40 Amps working on 240 volts 50 Hz AC supply,10 KA 'C' series complete all as specified and directed by Engr-in-Charge.

Supply & Fix Exhaust fan , 300 mm Sweep 240 volt , 1400rpm,Opal . White/brown including making provision on wall of suitable size for fixing 300 mm sweep exhaust fan making good disturbed surfaces to match with exisiting finish and after fixing exhaust fan flap cover to be fixing on behind exhaust fan hole , nut bolts , capacitors including all accessories complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of bell Buzzer, Ding Dong AC. 230 volts single polecomplete all as specified and directed by Engr-in-Charge.

S&F sheet metal enclosure with socket plug top, single pole and neutral enclosure with two pin earth plug and socket complete with one MCB SP of capacity 20 to 32 Amps complete all as specified and directed by Engr-in-Charge.

M&L for Sub main wiring complete with 2x1.5 sqmm , single core , multi stranded copper conductor FRLSH PVC insulated and sheathed cable 1100 Volts grade , drawn in PVC Casing Capping in surface /PVC conduit in concealed/surface (as required) along walls roofs etc including 1.5 sqmm size PVC FRLSH insulated unsheathed copper earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed by Engr-in-Charge. Note:- all three wire/cable(phase, neutral and earth) should be run through for each individual circuit from the DBs. Note. Two runs of cable and one run of earth conductor & one run of PVC casing be measured as one length)

All as per item No.102 but 2 X 2.5Sqmm and 1X 2.5Sq,mm for Earth wire complete all as specified and directed by Engr-in-Charge.

All as per item No.102 but 2 X 4Sqmm and 1 X 4.5 Sq,mm for Earth wire complete all as specified and directed by Engr-in-Charge.

Supply, installation, commissioning of water cooler fully stainless steel anti-corrosive pre-coated body, electric driven single phase having approx storage capacity 80 litres and nominal cooling capacity 40 Litres per hour including ball brass valve, drain pipe and necessary connection complete all as specified and as directed by Engineer-in-Charge. Make : Voltas of model : FS 40/80 N P

Supply, installation, testing and commissioning of industrial RO plant of capacity 100 LPH including internal plumbing by CPVC pipe complete all as specified and as directed with necessary accessories mentioned below: (a) PP Spun filter 20" - 02 No (b) CTO Carbon filter 20" - 01 No (c) RO membranes - 04 No (d) SMPS 24Volt - 02 No (e) SMPS adaptor - 02 No (f) RO Pump - 02 No (g) Solenoid Valve - 02 No (h) UV Section - 01 No Make: Bluemount or techno commercially equivalent make as approved by GE.

M&L for taking down RO and Water cooler of any type/capacity from old location of Navy Children School carefully by disconnecting existing electrical connection, removing aside, servicing by using blower/detergent for making dust free and applying lubricants to all the moveable parts and replacement of worn out bolts, nuts washers, etc, at site and fixing at new location of Navy Children School as directed including required plumbing work and testing complete all as specified and as dircted. NOTE : The cost of transportation for shifting of RO and Water Cooler, tools & plants etc., shall be deemed to be included in the quoted rate.

M&L for Submain wiring with PVC FRLSH insulated unsheathed multi-stranded copper conductor cable two runs of 4 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including PVC casing and capping for surface wiring with caping accessories and fixed above in the wall/ceiling and one run of 4 Sqmm PVC insulated copper conductor(FRLSH) for earth continuity wire complete all as specified and as directed by Engineer-in-Charge. Note : Two runs of single core cable with one run of earth continuity conductor and one run of PVC Casing & its accessories will be measured as one unit length.

Supply & fixing modular metal/PVC flush box 3 module complete all as specified and as directed.

Supply & fixing modular cover plate with frame 3 module complete all as specified and as directed.

Supply & fixing modular switch one way, 15/16 Amps, 1 module, 240 volts complete all as specified and as directed.

Supply & fixing modular socket, 2/3 pin, 6/16 amps, 2 module complete all as specified and as directed.

Supply and Fixing hi-wall mounted split units indoor/outdoor copper tubing in condenser unit including complete with cordless remote control unit, multi adjustable mode, anti microbial filteration,inverter compressor,including copper tubing upto 3m length and heavy duty MS stand for testing 5 Star rating of capacity 2.0 TR all as specified and as directed by Engineer-in-Charge. Make: Voltas Cat part No 245V Vectra Plus(4503456)

Supply and Fixing of Voltage Stablizer for automatic operation single phase naturally air cooled indoor type of designed for input variation between 170V to 250V with output voltage stablizeed at 230V with accuracy of 2.5% and Cap 5.0KVA complete all as specified and directed by Engr-in-Charge.

Supply & Fixing PVC pipe 20mm dia including Tees,bends,elbow,reducers and other fixing accessories, connected from rear side of AC upto drain with necessary clamp and fixtures on wall and floor complete all as specified and directed by Engr-in-Charge.

M&L submain wiring with two single core PVC insulated multistranded flexible copper conductor 1100Volts grade (FRLSH) cables 6 sqmm and 1 run 6 Sq mm PVC insulated multistrand copper conductor cable (FRLSH) of green colour for continious earthing drawn through PVC surface/concealed PVC conduit of suitable size and with all accessories all as directed and specified by Engr-In-charge.( Note: Three runs of 6 sqmm copper conductor and one run of surface/concealed PVC conduit of suitable size and with all necessary fixing accessories and making good disturbed surface area complete all as specified and directed by Engr-in-Charge.

Supply and fixing of vertical type of MCCB DB TPN 8 way IP-43 made of sheet metal sophicated, powder coated with bus bar, neutral link, earth bar and Din rail ,415 Volts with double door complete all as specified and directed by Engr-in-Charge. . Make :Make : Legrand Cat part No 507751 Note : Concealed the DBs on wall all including make in good and matching with existing surface.

Supply, fixing, connection and testing MCCB 3 Pole 415Volts breaking capacity 16 KA,"C" series of rating 100 Amps complete all as specified and directed by Engr-in-Charge. Make :Legrand Cat part No 4202 15

Supply fixing, connection and testing MCB TP 40 to 63 Amps 440 V 'C' curve complete all as specified and directed by Engr-in-Charge.

M/s J. M. Enterprises

bansal construction

BISAKHA PLUMBING WORKS

ANDAMAN PAINTS PVT LTD

EXCEL ENGINEERING WORKS

M/s Shiva Engineering

Tropical Refrigeration