PROVN OF SECURITY FENCING FROM MIL SLIDING RAMP TO SOUTHERN BOUNDARY OF MT OF B COY, GATE NEAR RAMP OF MIL SLIDING, TOILET ROOM IN BLDG No 17 OF 813 FD WKSP AND PROVN OF LADIES URINAL NEAR BLDG No 08 OF 132 SATA REGT AT NASIRABAD

Amount

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in any type of soil, complete, all as specified & directed.

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in soft & disintigrated rock, complete, all as specified & directed.

M&L for PCC 1:4:8, type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete, all as specified & directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6, complete, all as specified & directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls , built in cement mortar 1:4, complete, all as specified & directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Water proofing compound shall be measured and paid for separately.

M&L for reinforced cement concrete 1:2:4, type B1 using 20mm graded crushed stone aggregate in lintels over 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like, complete, all as specified & directed.

M&L for reinforced cement concrete 1:2:4, type B1 using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like, complete, all as specified & directed.

M&L for reinforced cement concrete 1:2:4, type B1 using 20mm graded crushed stone aggregate chajja and the like, complete, all as specified & directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete, all as specified & directed.

All as per description of serial item No. 10 here-in-before but 8mm dia bar.

All as per description of serial item No. 10 here-in-before but 6 to 10mm dia in stirrups, spacers and binders.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete, complete, all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete, complete, all as specified & directed.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces, complete, all as specified & directed.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick masonry, stone masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of primer, complete, all as specified & directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete, all as specified & directed.

M&L for 75 mm thick PCC (1:4:8), type D2 using 40 mm graded crushed stone aggregate as in sub base of floor, surface finished fair and even,complete, all as specified & directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete, all as specified and directed.

M&L for 25 mm thick sub base of PCC 1:2:4, type B0 using 12.5 mm graded crushed stone aggregate, complete, all as specified and directed.

M&L for glazed ceramic tiles (coloured) 7 to 8 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete, all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified & directed. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 2 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

S&F steel window/ventilator, glazed & gauged (combination) with side hung/top hung shutters incl box type/projecting type hinges and steel peg stay, handle & locking arrangement and frame made out of 1.25 mm thick pressed steel frame including guard bars and necessary cooler opening arrangement in window complete all as shown in drg No. CEBZ/TD/14/11 sheet No. 1/7 to 7/7, complete, all as specified & directed.

S&F 3mm thick figured sheet glass, pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete, all as specified & directed.

Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete, all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer, complete, all as specified & directed.

M&L for preparation of new untreated steel and iron surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of reflective synthetic enamel paint of approved tint over a coat of zinc chrome primer, complete, all as specified & directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) not exc. 30cm high with thick reflective synthetic enamel paint of approved tint all as specified & as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & directed.

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 complete all as specified.

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked), complete, all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked), complete, all as specified & directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors, complete, all as specified & directed.

All as per serial item No. 40 here-in-above but of 20mm bore pipe.

All as per serial item No. 40 here-in-above but of 25mm bore pipe.

S&F 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed. .

S&F 20 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed. .

S&F in repairs PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors or fixed to walls with MS stack clamps of FI 50x3 mm including fittings, complete, all as specified & directed. .Note :- Excavation & earthwork shall be measured & paid for separately.

All as per description of serial item No. 46 above but 75mm bore pipe.

S&F 110 mm bore PVC (SWR) vent cowl.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with oval access door.

S&F 75 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with oval access door.

S&F 110mm bore PVC (SWR) bend, any radius .

S&F 75mm bore PVC (SWR) bend, any radius with access door.

S&F tubular towel rail, aluminium anodized, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete, all as specified & directed.

S&F 15 mm bore bib tap of brass, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete, all as specified & directed. Make: Bharat, Dura pattern half turn Cat No. 2007 or equivalent from other specified make in PS Appendix.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc and, making good to floor, complete all as specified & directed.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle, complete, all as specified & directed.

S&F 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete, all as specified & directed.

S&F 15mm bore angle valve of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F soap dish holder (Cat Part No ACN-1131N of make - Jaquar or equivalent of Marc/Parryware/Somany/Parko/Gem/Prayag) complete all as specified & as directed.

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with including 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete, all as specified & directed.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides, complete, all as specified & directed.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 500 litre capacity, double layered, hoisted and fixed in position, complete, all as specified in SSR Part - I and as directed. Note :- (i) The unit rate quoted by tenderer shall be deemed to insulate water tank with GI pipe medium grade 10cm long projected inside and outside of tank with bore suitable for inlet and outlet, GI pipe 20mm bore medium grade projecting 10cm inside and outside of the tank for over flow, GI pipe 20mm bore medium grade projected 10cm inside and outside of tank for vent & mosquito cover for vent/overflow pipe.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms), complete, all as specified and directed.

M&L for precast concrete 1:2:4 using 20mm graded crushed stone aggregate as in manholes covers, cover slabs of drains and similar works including placing in position as directed.

Cutting in to existing man hole for removing existing branch drain, making good to walling and rendering, cutting out branch channel, and making good benchings, complete, all as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil, complete, all as directed.

Supply only integral water proofing compound (ISI marked).

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil, complete, all as specified & directed.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete, all as specified & directed. Note :- Soil obtained from excavation under serial item No. 1 here-in-before shall be used for filling under floors.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point, complete, all as specified & directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe, complete, all as specified and directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested, complete, all as specified & directed.

Excavation in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil.

M&L for RCC 1:2:4 (Nominal mix), type B1 using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like.

M&L for RCC 1:2:4 (Nominal mix), type B1 using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete, complete, all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L for framed work such as grills, gratings, iron doors of approved intricated ornamental design, forged in to spikes, railing etc made from angle iron or MS box sections and flat iron in any section, cast iron decorative fixtures etc including cutting tops to shape, drilling holes and notching, welding, pintel & locking arrangements etc required conforming to Fe.290.Gde-E-165, complete, all as specified & directed.

M&L for framed work such as grills,gratings, etc.. with ends of bars, shouldered and/or riveted,or forged into spikes; framed, guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete, all as specified & directed.

M&L for Mild steel, plain, 1.00 mm thick black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete, all as specified & directed.

M&L for cement concrete 1:2:4, type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified.

M&L for Dholpur stone with hammer dressed facework (with maximum depression from a straight edge held against the dressed surface not exc 20mm), about 40mm high, 75mm deep in straight courses, laid and jointed in cement and stone dust mortar 1:3, recess pointed (10mm x 20mm) with an admixture of white cement and Dholpur stone dust 1:1 over and including 10 mm thick screed bed in CM 1:4, complete, all as specified & directed.

Surface dressing not exc 15cm deep in soft/loose soil.

M&L for cement concrete 1:3:6, type C1, using 20 mm graded crushed stone aggregate as in roof kerbs or mud stops, coved fillets, rounded or chamfered on edges all as specified & directed.

S&F mild steel work as in angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) and similar works conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 75 mm long and dia of neck 5 to 10 mm complete all as specified.

Supply only mild steel galvanized chain link fencing 3.00 mm dia of mesh wire, mesh size 50x50mm complete all as specified and as directed.

Fixing only mild steel galvanized chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire.

Supply only plain mild steel wire of 4mm dia , galvanised class 3, cut to lenth as required for fixing chain link fencing, ( Note: Fixing of line wire in included in quoted rate of item No.89)

S&F galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc as directed.Note :- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment.

M&L for preparing surfaces of new steel and iron work, of any description and girth, and treating ends of posts with tar or coal tar black paint etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each, complete, all as specified & directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20 mm dia or higher complete with all PVC conduit accessories and sunk type anodised terminal box thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light/fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

S&F switch piano flush type 5 Amps, single pole one way.

S&F Socket outlet, 3 Pin 5/6 Amp, flush type.

S&F ceiling rose surface bakelite, 3 terminals 63.5 x 17 mm.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt), 230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders, LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make: Bajaj Cat Part No BLRB 18W CW (tube) & BLRB-DB 118(batten)/ Havells Cat part No LHLDDBXEUL7Z018 (tube) & LHFYBWP1TB1W020 (batten)/Syska Cat part No SSK -T8-18W (tube) & SSK-TL-22 F (batten)

S&F asthetically designed linear LED mirror light fitting, 10 Watt, complete, all as directed by Engr-In-Charge.

S&F of lamp holder PVC/polycarbonate type with back plate including LED lamp 9/11 watt complete all as specified and directed.

S&F energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lence embedded , polycarbonate diffuser, IP 66 protection including connecting with three core copper flexible wire from ceiling rose to connector of light fitting, complete with street light bracket made of 32 mm GI pipe , 1.2 mtr lenght with clamp, nut and bolts complete all as specified and directed. Make : Havells Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC or equivalent from other specified makes in Appendix of PS.

S&F Exhaust fan, metal body, 300mm sweep, suitable for 230 Volt, SP, 50 Hz including louvers, complete, all as specified & directed. Make: Havells, Model: Ventil Air DS or equivalent from Bajaj/Khaitan.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 415 volts suitable for housing MCB's complete, all as specified and directed. Note: MCB DB and MCBs shall be of same make.

S & F of MCB SPN, 240 volt, 25 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 to 32 Amp capacity, 10 KA , 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh, PCC chamber in cement concrete 1:3:6 type C-2 and RCC 1:2:4 type B1 cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete, all as specified & directed.

Supply, laying & testing of LT cable, 1100 volt grade, heavy duty of size 10 Sq mm, 2core with PVC insulated aluminium stranded conductor with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and over all PVC sheathed, complete all as specified and directed

Supply and laying dry river sand for cable cushioning in trenches to required width at bottom and top cable including spreading, levelling, watering and consolidation, complete all as specified and directed by Engineer-in-charge. Note: Punned thickness only shall be measured and paid.

Supply and laying of bricks of old class ‘B’ as protection cover to UG cable, laid flat adjoining to each other width wise, complete, all as specified.

Supply and laying GI tubing 40 mm bore, light grade with all fittings, laid in trenches/under floor or fixed on pole/on wall for cable protection.

Supply, laying, jointing and fasting of cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cable, heavy duty, 1100 volts grade in stranded aluminium conductor of size 10 Sqmm, 2 core, laid in trenches/ducts, or fix to pipe on walls, poles etc., complete, all, as specified and directed. Note :- Excavation earth work, sand cushoning and cable cover will be measured and paid separately.

Supply, laying & testing of LT cable, 1100 volt grade, heavy duty of size 4 Sq mm, 3 core with PVC insulated aluminium stranded conductor with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and over all PVC sheathed, complete all as specified and directed

Supply, installation, testing and commissioning of LED flood light with pressure die-cast aluminium housing, IP-66 protection, energy saving, environmental friendly, long life, 120 watt LED fitting with all accessories complete all as specified and directed. Make : Model No BJFL 120W Bajaj LED or equivalent from Havells /Philips as approved by GE

Supply, installation, testing and commissioning of 10 metre height hot dip galvanised octagonal poles with 155 mm bottom A/F and 70 mm top A/F made up of 3 mm thick HR sheet along with base plate dimensions of size 250x250x26mm thick with and including four Nos of M24x750mm long GI type EW8 grade foundation bolts alongwith template and hot deep galvanised circular ring type made up of 40 NB dia Gi pipe suitable to mount on pole having top 70mm A/F suitable for mounting four flood lighting luminaries symmetrically fitted, platform for repair of light, including RCC foundation, excavation and earthwork in any type of soil, complete all as per manufacturer instructions cylindrical, control box rewired with MCB, loop in and loop out arrangement terminal box etc. as per manufacturer instruction, complete all as specified and directed Make: Crompton/Surya

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm, lime or sand stone, complete, all as specified & directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:6 complete all as specified & as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

S&F factory made solid PVC moulded door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing on ser page No. 161 of SSR(Part-I )-2010 and asdirected. Note: Cadmium screws to be used for fixing fixtures.

S&F 15 mm bore bib tap, long nose, fancy type, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete, all as specified & directed.

S&F 15mm bore pillar tap, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete, all as specified & directed.

S&F vitreous china urinal, flat back, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia, complete, all as specified & directed.

Supply & laying FRP septic tank package type waste water treatment system (PWTS) Model No. PWTS-AM-180-01 of Sintex or equivalent 1490 mm dia and 1615 mm height including necessary inlet & outlet pipe designed to carry sewage and salvage water, With UPFLOW FILTER INLCUDING MEDIA including necessary excavation, PCC (1:4:8) below foundation bed, vent pipe, inlet and outlet connection pipe upto 2.00m length etc, complete all as specified and directed. Make :- Model No. PWTS-AM-400-01 of Sintex or equivalent make if approved by GE.

M/S Bansal Construction