Widening and Strengthening of internal road in CHC at village Kalwa Distt. Jind. (Pdg. Street Light n High Mast only)

Amount

Moulded case Circuit breakers 31.12 (c) Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections.

31.12 c (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

31.12 c (ii) 100 amp.to 220 amp.415 V,10 KA 3-phase

Miniature Circuit Breaker and Isolator 31.17 Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections.

(a) Miniature circuit breakers of 9 KA breaking capacity.

31.17a) (ii) SP MCB of 9 KA breaking capacity 6 amp. to 32 amp.

31.17(a) (ii) TP MCB of 9 KA breaking capacity 6 amp. to 32 amp.

31.17(a) (iii) TPN MCB of 9 KA breaking capacity 40 amp. to 63 amp.

31.22 Earthing

31.22(i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required .

31.22(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required. .

31.22(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required . .

31.26 Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections

31.26 (xIi) Ard 25 Sq. mm 4 Core Cable .

31.26 (xxxix) Ard. 10 Sq. mm 4 Core Cable

31.26 (xI) Ard.16 Sq. mm 4 Core Cable

Pedestal 31.33 Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:-

31.33 (ii) M.S.pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level .

31.40Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe .

31.40 (i) Size 1.5 sqmm ( 3/0.81 )

31.41steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work.

31.41 (v) 4-way , TP&N ( Horizontal) (8+12)

31.67 Supply and erection of mark double walled corrugated (DWC) HDPE pipe laid 1Mtr. Below ground level including diging and refilling of earth including cost of sutiable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

(i) HDPE pipe 63/50 mm outer dia/inner dia

31.68 Supply and Erection of Hot Dip Galvanized octagonal pole of 3mm thickness with base plate including cost of nut and bolts and all accessories as supplied by the manufacture including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete with door locking arrangement. Terminal plate consisting of 2 Nos. 100 A, 4 pole natural links including connectin etc. with suitable connecting arrangement for 2 No. MCBs/ Kit Kat including cost of R.C.C 1:1 5:3 for foundation of size 0.7M x 0.7 M x 1.8 M with minimum 8 Nos. 12 mm dia longitudinal MS reinforcement rods with rings of 8mm dia not more than 200mm C.C for fixing the pole with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

(i) 7 Mtr. Long pole with top dia 70mm and bottom dia 130 mm with base plate of size 220x220x12mm

31.83 (i) Supply, installation, Testing and commissioning of 12.5 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 Nos. Luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge Thickness of Top Section = 3mm (Minimum) Bottom Section =3mm (Minimum) Top Dia = 150mm Bottom Dia = 360mm Thickness of Galvanization = Top = 65micron (Min.) Bottom = 85micron (Min.)

31.83 (ii) Supply, installation, Testing and commissioning of 16 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 Nos. Luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge Thickness of Top Section = 3mm (Minimum) Bottom Section =4mm (Minimum) Top Dia = 150mm Bottom Dia = 410mm Thickness of Galvanization = Top = 65micron (Min.) Bottom = 85micron (Min.)

M.R. items N.S - 1 Supply and Erection of LED flood light fitting Havells Make JETA-AIRISFLS150W or its equivalent model of Wipro LF20-192-060-57-XX / Philips with pressure die cast alluminium housing, IP-66 reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

N.S - 2 Supply and Erection of LED flood light fitting LFLE-60-CDL 60 Watt of Havells make or its equivalent make of Wipro LF 19-711-060-57 / Philips make BVP-120 LED 70CW with pressure dia cast aluminum housing, reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

N.S - 3 Supply & Erection of Single arm bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

N.S - 4 Supply and Erection of LED street light lumanaries of Havells make Endura PLEARL NEOSL 60W LED or its equivalent make of Wipro make LR02-671-xxx-57-xx / Philips make BRP409LED 060CW with die cast housing, toughened glass IP66 with all acessories as supplied by the manufacturer with all labour and material required to complete the job in all respect upto the Entire Satisfaction of the Engineer-in-Charge of the work.

N.S - 5 Construction of RCC foundation for 12.5 / 16 / 20 mtr. high mast complete in all respect as per the appended design including the cost of digging sand filling 6" lean concrete 1:8:16 / bricks souling, Bar binding cement concret (M-20) shuttering, fixing of foundation bolts, refilling, carrying and erection of High Mast on foundation including petty material to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. (Foundation bolts and template to be supplied by department).

N.S - 6 Supply and erection of 32/63 Amp. 3 Phase automatic time switch of L&T make alongwith contactor of required capacity of L&T make movement controlled by precisaty quartz osciliation operation on main supply of continue to run on built in rechargeable nickel cadium cell for 150 hours in the event of power failure including cost of contractor complete in all respect upto the entire satisfaction of Engineer-in-charge of the work.

NS-7 Supply and erection of 0.3 KVA capacity inverter with SMF battery for aviation light in existing panel including the cost of labour charges and connections and petty material etc. for complete in all respect upto the entire satisfaction of Engineer-in-charge of work. Make of Invertor :- Lumineous / Microtek / Sukam - Make of Battery: Exide / Amron

NAVEEN LIGHT AND SOUND SERVICE

INFERNO POWER AND SAFETY

Balraj Singh Contractor

PS ELECTRIC

Raghbir Sarup Govt.Cont.

DEVENDER KUMAR CONTRACTOR