SPECIAL REPAIRS TO BLDG NO. P-73 (EKM WORKSHOP) AND P-74 (EKM OFFICE) AT NAD TROMBAY

Amount

SCHEDULE 'A' PART I (B/R WORKS) Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Dismantling of brick work /stone boulders built in cement mortar including all quins, arches, pillars etc complete all as specified and as directed.

M & L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built CM 1:4 complete all as specified.

M&L for Ready mix plaster 10mm thick on faces of bricks or concrete surface including necessary scaffolding upto 18m height, including preparation of wall surfaces etc complete all as specified and directed,

M&L for Ready mix plaster 15mm thick on bricks or concrete surface including dubbing coat to match with existing with necessary scaffolding upto 18m height including preparation of wall surfaces etc complete all as specified and directed,

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: Hard concrete shall not be removed by force.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed . Note:- Mode of measurement: superficial area of concrete will be measured.

M&L for providing mild steel TMT bars in various structural RCC elements like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with binding wires etc. complete all as specified and directed. Note: This item is applicable for additional bars required in the existing RCC structures.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 60mm in thickness) with prebatched, prepacked, single component ready to use microconcrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications and all other relevant worksincl scaffolding upto 18 mtr height complete all as specified and directed. (Note : Reinforcement only shall be measured and paid separately).

M&L for prepration of newly plaster/concrete surface of wall and applying two coat of distemper oil emulsion on walls with one coat of primer ( chalk white on plastered surfaces) and including 3mm thick putty applying complete all as specified and directed.

M & L for preparing old decorated surfaces of wall (plastered or unplastered or previously white washed ) & applying two coat of white wash complete all as specified.

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of oil bound distemper incl upto 3mm thick putty over one coat of primer applying on walls for smooth finish complete all as specified & directed .

M&L for preparation of new plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as in camouflage pattern complete all as specified and directed.

M&L for complete removal old plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as in camouflage pattern complete all as specified and directed.

M& L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors , aprons etc

M&L for Light Shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) of approved size, area of each tile not exceeding 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for Light Shade 600x100x10mm thick size Vitrified Ceramic tiles, on vertical surfaces such as skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete as specified and directed.

M&L for coloured glazed ceramic tiles Glazed ceramic tiles invertical surface 350x 250x 6-7 mm/ 400X 300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick, with expansion joints & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

S&F in repair 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including dismantling if any

Supply and fixing of 16 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (including provision of special fittings i.e. brass elbow, brass tee, Male brass threaded adaptor, female brass threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) concealed in walls/ ceiling or laying in floors etc., also including cutting chases, grooves and making good the same in CM 1:3 after fixing of pipes / fittings, incl taking down of old pipe complete all as specified and directed.

Supply & fix 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, incl taking down of old pipecomplete all as specified and as directed.

Supply & fix 40mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, including taking down and removal complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia out let including grating connecting jointing to waste pipe and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F in repair towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms)

S&F in repairs high level/low level PVC flushing cistern with PVC flush pipe, brackets, and PVC connection complete of 10 Ltr capacity.

S&F in repairs 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated.

S&F in repairs 15mm bib taps two way cock, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated. Make : Jaquar or Equivalent

S&F in repairs pillar taps 15 mm; of cast copper alloy with capstan; head chromium plated screwed downend with pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe& fixed complete all as specified and directed.

S&F in repairs stop cock/angle valve 15mm cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass chromium plated with fancy type.

S&F in repairs Grating doom 100mm dia of PTMT

S&F in repairs Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) ® Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour (minimum weight 150gms) and minimum size 125mm dia or 125x125mm in square.

S&F hand shower (health Faucet) with 8mm dia 1 mtr Long flexible tube & wall hook complete all as specified .

S&F in repairs Wash basins, Vitreous China (flat back or angle back type), including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe flat back, size 580x450irun (for Hospilal use) excluding taps, waste, chain and plug and porcelain stopper but including bracket and coupling complete all as specified and directed.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant as per specifications drawing as directed by the Engineer - in -charge . Material test certificate and authentication should be compulsory provided by the manufacturing company.and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

M&L for 35 to 40 mm thick machine cut, prepolished cuddappa stone slab as in plateform for fixing oval shape wash hand basin(including cutting the slab to oval shape to accomdate the sink and WHB), pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc,also including moulding/rounding to edges of the slab, including dismantling of existing tile slab complete as specified and directed.

All as per item No. 45.00 above but except stone (for mirror polished only)

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

All as per item No. 49 above, but 75mm bore in repair

S&F in repair Vitreous china squatting pan orrisa pattern of size 580 x 440mm with integral foot rest and 'P' or 'S' trap including lime concrete bedding connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed

S&F in repair Vitreous china Wash down water closet (Pedestal pattern), complete white (excluding fixing bolts, flushing cistern, and flush pipe) and 'P' or 'S' trap, seat covers, connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed

Removing plant/growth including its roots upto 1.00m of plant height at any location/at any storey and of any description and treating the surfaces with Acid (HCL) and making good surfaces with cement mortar 1:4, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends

S &F PVC (SWR) bends, 75 mm bore,

S &F PVC (SWR) junction single(single T), 110 mm bore, equal or unequal

S &F PVC (SWR) junction single(single T), 75 mm bore, equal or unequal

S &F PVC (SWR) branch piece,double( Singe Y) 75mm bore equal or unequal

S &F PVC (SWR) branch piece,double (single Y) 110 mm bore equal or unequal

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) Sqm but not exc 1.5 Sqm each including complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperature 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2020 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F 100 mm long stainless steel butt hinges fixed with stainless steel screw

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 250 mm.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate, coping, surface chanels etc including necessary form work complete all as specified and as directed.

M& L for preparation surfaces of new or previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M& L for preparation old surfaces of wood of any description over 10 cm width or girth and applying One coat of synthetic enamel paint as specified.

Demolition of brick/cement concrete (unreinforced) / pcc tiles from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retreived debris out side MD land, all as specified and directed.

M&L cement plaster (1:3) with 10 mm thick to be finished smooth without using extra cement mixed with WPC @ 2% by weight of cement, , complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

M & L for APP modified roof treatment over existing roof slab etc including taking down to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sq cm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane for non accessible roof complete all as specified and directed.

M&L Preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10 centimetre width or girth and applying One coat of synthetic enamel paint complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

Supply only 4mm thick sheet glass, ordinary quality fixed in aluminium window along section all as specified and directed

Supply only Stainless steel wire cloth.0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed with stainless steel wire staples in aluminium windows or along with 'F' section complete all as directed by EIC.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc, complete all as specified and directed.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-410-0 or Fe-310-0 all as specified & directed.

S&F mild steel Framed work such as grills, gratings etc, with ends of bars shouldered or rebated or forged into spikes, framed guard bars, barred iron doors, railings, framework of water tanks and similar work conforming to Fe -290 Grade -E-165, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including dismantling of roof sheet any type

M&L two coat of synthetic enamel paint over red oxide over preparation of new steel surface complete all as specified.

Taking down existing aluminium grills from balcony/ any locations complete all as specified and directed.

S&F aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel including drilling as required in RCC sections in rectangular or architectual type balcony opening in existing building, complete all as specified and directed. Note: The Grills shall be of Model DG-100/DG-102 of Make Deco or equivalent make as approved by the GE.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces using CM 1:4, finished the surface even and smooth all as specified and as directed.

S&F cast iron covers and frame grade FG 150 unmachined as in manhole covers etc including locking arrangement,and removing old Unsv covers complete all as specified

M & L Cement Concrete Type D2 1:4:8 (40 mm graded aggregate) in subbase 75 mm thick

M & L Chequired cement concrete tiles 300x300mm of 25mm thick lacquer coating glossy finished , set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed in CM (1:6) all as directed

M & L for pvc tiles/sheets 2.0 mm thick homogeneous laminated plain coloured laid with approved rubber based adhesive in floors complete all as specified and directedby eng in charge .

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, grid etc

Supply and fixing hot dipped GI imposed grid with 24mm wide T section exposed flanges powder coated frame work comprising of main runner made from 0.33 mm thick GS sheet of size 24mmx32mmx3000 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug,level adjusters and screws etc flush fitting of 1200mm long cross tee interlocked between main runners @ 600mm c/c to form 1200mmx600mm modules cross tee longer than 600 mm to be supported independently 600mmx600mm modules shall be formed by fitting 600mm long cross tee centrally between 1200mm cross tee ,perimeter wall angle shall be GS of size 19mmx19mm and 0.45 mm thick 300mm long including 600mmx600mmx8 to 10mm thick armstrong gypsum reinforced board with painting with two coat of plastic emulsion paint over primer complete all as specified.

S& F in repairs steel rolling shutters without ball baering gear operated type without ball bearing as sppecified and including top cover anchoring rod hasp and staples and one shope coat of primer erected in position as indicated complete and wicket door including 4 lever mild steel safety lock lacakble from both side (area of of wicket door to be only measured)

S & F safety lever locks mild steel with 4 lever locks rolling shutters.

S& F ball bearing for rolling shutters

Dismantling structural steel work including doors gates but excluding framnes truss etc completed

SCHEDULE 'A' PART I (E/M WORKS) M&L for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 sqmm drawn in and including PVC concealed conduit of suitable size of wall/RCC slab/ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, with suitable sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches/sockets/fan regulators fixed with Cadmium plated machine screws complete etc all as specified for one light/fan/bell point controlled by one switch. Note: 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit

All as per item No 99.00 above but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No 99.00 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

S&F Modular type 6 Amps 01 way SP switch 01 module confirming to IS 3854-1997 with finger proof terminal 230 Volts ISI marked complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F Modular type 2/3 pin 6 Amps socket 2 module confirming to IS 1293-2005, 230 Volts ISI marked, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F Modular type 2/3 pin 16 Amps socket 2 module confirming to IS 1293-2005, 230 Volts ISI marked complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F ceiling rose three terminal, 230 Volts ISI marked PVC / Polycarbonate body, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F fan regulator, Modular type 120 watt step fan regulator of 02 modules size confirming to IS 11037-1984 and connecting-up, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

Supply & Fix LED aluminium Batten type fitting of capacity 20W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 100 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of engineering plastic with decorative end caps elegently designed complete all as specified. Make :-BAJAJ-BCLAV20W-LEDP/ JAGUARLGLZU1X022XC/ WIPRO/ Note : The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete Make: Jaguar LULTU1S036XC/Bajaj/Wipro/Halonix HLFPS22S06-36-CW Note : The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charge.Make: Bajaj BIBWP10WLED/Jaguar LBLK02X010XC/Halonix-HLBH-21-10-CW Note : The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

S & F LED light fitting 1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed Make: Bajaj BIB WP 10W LED/Wipro/Jaguar/Halonix HLBH-02-10-CW Note : The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

Supply & fix in repairs very high efficiency round LED Highbay Industrial light fittings 120 Watt ( 130 Lm/W) in PDC housing, IP 66 luminaire including driver and required GI tube down road of length up to 2 meter with hoooks for hanging the fitting including fixing arrangements and taking down old us rusted bracket fittings complete etc. The Make :-Jaquar (Model No LHBLDUL120XC)/Bajaj OPTIBAY 120W WH NB PC SD/Halonix HLBLD-ML-54-120-CWDL-R-HL2/ Crompton / Havells /Bajaj Note : (i) Fittings shall will be installed in Hangers/Sheds, hight up to 10 Meters only and directed by Engr-in-Charge. (ii) The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

Taking down in repairs old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 2.5 mfd - 01 No., PVC canopy - 02 No's and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Supply and fix fans ceiliing with BLDC motor complete with blade, canopy, down rod, mounting hook, rubber insulator etc, the colour of fan shall be of Elegant White/Dubai white/ White CF without remote control alongwith batteries and accessories 230 V, 1200 mm sweep, BEE 5 Star rated complete including takingdown old unserviceable fan all as directed by Engr-in-Charge. Make : Havells (Efficiencia Neo (BLDC 26 W) /Orient FALCON 400 / Bajaj (ENERGOS 28) Note : Unserviceable ceiling fans shall be deposit to MES store.

Taking down old unserviceable exhaust fan 300 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 2.5 mfd - 01 No. and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Supply & Fix Heavy duty Metallic Body Exhaust fan of sweep 380 mm with frames, blades including provision of mounting anchor fasterners aluminium louvers made of aluminium sheet of 0.5 mm thickness provision of three core 1.5 sqmm copper cable from ceiling rose to fan, making opening of required size in cement mortar brick wall/ RCC for fixing of exhaust fan, making good the disturbed surfaces in CM 1:4 including scafolding if any required to carry out the work in building of height up to 20 meters complete.Make: Orient/Bajaj/Crompton/Almonard

Supply & fix in repairs Industrial type Wall mounting fan 450 mm sweep, operating on single phase, 230V, AC, 50 Hz having speed of 1400 RPM, air delivery 115 CMM, power output of 100W star rated along with blade, canopy, mounting brackets, rubber insulator. Make - Bajaj ( model - 250439)/ ALMONARD / ORIENT

Supply & fix in repairs Pedestal Fan 450 mm sweep, operating on single phase, 230V, AC, 50 Hz having speed of 1400 RPM, air delivery 115 CMM, power output of 100W star rated along with blade, canopy, mounting brackets, rubber insulator. Make - Bajaj ( model - 250439)/ ALMONARD / ORIENT

Supply and Fix in repairs MCCB 100 Amps 4 pole, 415 Volt 25 KA IN SHEET STEEL ENCLOSURE in open construction, panel mounted 0n wall with base plate for mounting in panel, including taking down of old MCCB with enclosure and reconnecting the cabes with proper glands.Make: Indo Asian /ABB/Havells/ Standard,Legrand/Schneider

S & F MCCB TPN DB, 4 way TPN (vertical type), double door, 415 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating. Make -Havells/Indoasaian/Legrand/ABB/Schnider

S & F in repairs MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete including taking down old us DB all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating. Make :-LEGRAND / SCHEINDER / L & T.

Supply & fixing MCCB 4 Pole,415 V, fixed type, 125 Amps with breaking capacity 25 KA including connecting up electrically with proper lugs glands and including all necessary fittings complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider

Supply and fixing TP 63 Amps rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make -Havells/Indoasaian/Legrand/ABB/Schnider

S & F in repairs MCB SPN 20 to 32 Amps, 240 Volts, 50 Hz, 10 KA Breaking capacity. Make :- LEGRAND/ SCHEINDER/ L&T

S & F in repairs MCB SP 5 to 32 Amps, 240 Volts, 50 Hz, 10 KA Breaking capacity. Make :- LEGRAND/ SCHEINDER/ L&T

S&F in repairs single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 20 Amp 240 Volts complete all as specified including concealing in wall and directed. Make :- LEGRAND/ SCHEINDER/ L&T

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2KW,230V/50Hz,Temperature Range 25 to 70 degree celcius & working pressure 0.8 bar capacity 25 ltr,BEE5 star rated complete with all accessories such as safety valve,thermostat,NRV,Connection peice etc complete all as specified and directed. Make: RACOLD Andris Uno 3180607/BAJAJ Bajaj shield series crest SKU 150977/Orient SWPR25VCG8M2-WG Note: Contractor will give the warranty-5 Years of tank,2 years of heating and 2 years on other parts on geyser supplied.

M&L in repairs for sub main wiring with two single core 10.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 6 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

All as per item No 127.00 above but for 6.0 sqmm complete all as specfied and directed.Make of casing caping-: Sudhakar/Precision/ Diamond, Make of wire-: Finolex/ Havells/ Polycab/ KEI

All as per item No 127.00 above but for 4.0 sqmm complete all as specfied and directed.Make of casing caping-: Sudhakar/Precision/ Diamond, Make of wire-: Finolex/ Havells/ Polycab/ KEI

All as per item No 127.00 above but for 1.5 sqmm complete all as specfied and directed.Make of casing caping-: Sudhakar/Precision/ Diamond, Make of wire-: Finolex/ Havells/ Polycab/ KEI

S & F in replacement building Security light fitting 35/36 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP 65/66 protection and impact resistance of IK 07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. Make :- Bajaj (Model No-ENXT P42L WH PO PC SD MT), Wipro( LR02-391-XXX-57-XX) Note : The lowest tenderer shall furnish 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory

S & F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

Supply, install, commissioning and testing of commercial Air curtain unit for prevention of dust and conditioned air losses, three phase 440 V, 50 Hz, made out of MS/ CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat ofsynthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1- 1.5 m/sec air velocity at floor level for door opening complete all as specified and directed by Engr-in-charge.Make: Almonard/Aircon/Crompton Greaves/National

M & L for cleaning, greasing, oiling and servicing for smooth functioning of all parts of rolling shutters of any size including fixing of Motorisation system operating on single phase, 230Volts,50Hz AC supply) gear box etc as required including scaffolding and other safety measurements complete all as specified and directed.

M & L for flameproof surface wiring on wall/ceiling / roof with necessary fixing arrangements with stranded PVC-FRLS insulated and unsheathed copper multistranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including 16 gauge stove enameled ERW rigid steel conduit (metallic) not less than 19 mm dia with all MS conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including PVC-FRLS insulated and unsheathed copper multistranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces complete including taking down old us worn out wiring & fittings all as specified and directed by Engineer-in-Charge for one light, fan point controlled by one switch Note : Junction boxes shall be measured and paid separately.Make: Sudhir/Shyam Switchgear/Baliga

S&F flame proof weather proof threaded type junction box LM 6 aluminium alloy 2 to 4 way complete all as specified and directed. Make: Sudhir/Shyam Switch gear/Baliga

S&F flame proof weather proof metallic hose conduit 3/4 " dia 300 mm long complete all as specified and directed. Make: Sudhir/Shyam Switch gear/Baliga

S&F flame proof double compression brass cable gland 3/4" dia complete with nipples complete all as specified and directed.Make: Sudhir/Shyam Switch gear/Baliga

S&F Flame proof weather proof Rotary switch with cable termination in LM 6 aluminium alloy housing 16 Amp, 240 volts complete all as specified and directed.Make: Sudhir/Shyam Switch gear/Baliga

S&F Flame proof weather proof exhaust fan 450/ 457 mm sweep' 1440 RPM single phase 230 volts complete with louvers & all accessories & fitting arrangements complete all as specified and directed.Make: Sudhir/Shyam Switch gear/Baliga

Supply and fixing LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.Make: Sudhir/Shyam Switch gear/Baliga .

Supply an Fix in repairs/replacement CIMFR Certified 60 Watts LED Flame proof Fitting, wellglass in die cast AI housing with heat resistance toughetned complete with all acessories and including connecting up with three core flexible multi strand copper conductor of 1.5 Sqmm, drawn through steel conduit confirm to Cat No SSPL/1233 of Shyaam switch gear/ Baliga /Sudhir complete all as specified and directed by the Engineer-in-charge.Make: Sudhir/Shyam Switch gear/Baliga

S & Fix wall mounted out door type double door LT Panel made out of 3 mm thick CRCA Sheet, the panel shall be provided with flame proof MCB DB made out of Cast aluminium alloy LM6, inside and out side light gray epoxy powder coating shade, 'O' ring endless neoprene rubber gasket, with 1 No. cable entry for incoming cable and three Nos cable entry for out going circuits with and including cable gland and stopping plug, 1 No MCB SPN 32 Amp as incoming and 2 Nos MCB SP 6 to 32 Amps for out going connections IP 65 protection as per IS 2147/1962. The panel shall be powder coated, front openable and locakable with key and shall be fabricated from CPRI approved manufacturer complete including taking down old DB all as specified and directed by the Engineer-in-charge. Make: Sudhir/Shyam Switch gear/Baliga

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified.Make: mehtab/National tiles

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 150 Sqmm 3.5 core including necessary connection and providing cable lugs as required all as specified. Make: Polycab/Havells/KEI Note: Excavation & Earth work shall be measured and paid separately under appropriate item of this schedule.

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 Sqmm 4 core including necessary connection and providing cable lugs as required all as specified. Make: Polycab/Havells/KEI Note : Cable shall be clamped on wall.

M&L for cutting existing road/hard and dence soil not exc 45 x 60 cm in wide & depth getting out excaveted materials for laying GI tube; returning filling & well rammin watering finish surface 10 cm from top using PCC 1:3:6 not less than 4 inch thick; including removal of surplas soil all as per directed.

S&F of HDPE pipe 50 mm dia, PN-10 for laying in ground, raod crossing etc for cable protection including necessary fittings, clamps for supports, etc complete all as specified and directed.Make: Sudhakar/Plasto/Prayag.

Supply install, in repair Powder coated LT kiosk cubical indoor type (double door openable) Channel mounted compartmentalized in construction all Confirming to IS 8623 Part 1 1993 CPRI approved factory as per CA fabricated made out of 3 mm thick CRCA sheet & suitable size to accomodate all accessories / fittings, to accommodate incoming MCCB and TPN Copper bus bars, incomer MCCB and outgoing MCCB, MCB, Contactors The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator. The bus bar shall have copper extension links for connecting with out going MCCB. The cubicle shall have a bottom channel & free standing frame made of angle iron of size not less than 40mm X 40mm X 6mm of A detachable predrilled gland plate of thickness not less than 3 mm thick powder coated should be used at the bottom for entry of armoured cable of adequate size with glands.The above panel shall be front & back openable lockable /openable by key from both side. The panel shall be Dust, vermin proof and powder coated of approved thickness complete including CTs, control wiring by 1.5 Sqmm Wire and consisting the following, including taking down of old unsv panel after disconnecting Existing cables, Existing energy meters and re fixing the energy meters at new panel & Reconnecting the cables to new panels and including PCC foundation, excevation, grouting bolts.: , complete as specified and consisting the following :- i) Electrolytic Copper Busbar TPN 400 Amps -1 Set iv) MCCB 250 Amps 25 KA FP, Thermal magnetic type - 01 Nos (Make: L&T,Schneider,ABB,Legrand) vii) MCCB 200 Amps 25 KA FP, Thermal magnetic type - 02 Nos (Make: L&T,Schneider,ABB,Legrand) viii) MCCB 100 Amps 16 KA FP, Thermal magnetic type - 02 Nos (Make: L&T,Schneider,ABB,Legrand) viii) MCCB 63 Amps 16 KA FP, Thermal magnetic type - 01 Nos (Make: L&T,Schneider,ABB,Legrand) ix) MCB TPN 32 Amps - 02 Nos (Make: L&T,Schneider,ABB,Legrand) x) MF Meter 4410 series -01 No xi) Indicating Lamps LED Type-03 Nos Note –: The Lay out drawing of the panel shall be got approved by the contractor from GE before the panel fabrication work.

M & L for earthing chemical with copper plated 50 mm dia pipe 3 mtr long (100 microns) including Electrodite 50 Kg buried directly in ground including earth bore hole work (earth bore not less than 3 Mtr deep below normal ground level and connected to copper earth strip of size 20×3 mm by means of copper nuts bolts with washers and connected as per following specifications complete all as directed by Engineer-in-Charge. (a) Product Model: ASEEL 19 CP, 3 meter long (Copper Plated) – 100 microns . Fast Electrode, Model FE 80 mm 3 mtr (Pure Copper Single Pipe), Outer Dia is 80 mm with a wall thickness of 2 mm, Inner Dia is 26 mm with a wall thickness of 2.6 mm, Overall Length is 3000 mm, External Corrosion Protection: Copper Plated (100+ microns), Internal Corrosion Protection: In addition to Copper Plated (100+ microns), a ground breaking corrosion resistant Crystalline Conductive Compound is filled and compacted in the cavity within the pipes to enhance the electrodes performance. Conforms to IS: 3043 - 1987 i.e., Code Of Practice For Earthing (+ 10%) variations in dimensions applicable. (b) Electrodite backfill: Fast Electrode Earth Enhancement Compound, Manufactured using Eco - Friendly minerals, Blended homogeneously with conductive carbon(s), Resistivity: < 5 ohm-metre (In ideal moist conditions); > 5 ohm-metre (Dry Conditions), Ph Value: 7.0 - 8.5, High water retention capacity, Hygroscopic, Ionic & Electronic conduction, Swells when it comes in contact with water thereby engaging constant contact between the electrode surface & soil which is a crucial aspect in the performance of an earthing system. Packing Size : 2 Bags of 25 kilograms, Recommended for normal soil conditions. Conforms to IS : 3043 – 1987 Note : Chemical Earthing for Equipment installed in Workshop.

Supply & Fix copper strip of size 20 X 3 mm duly covered, fixed on porcelain insulators along the wall / roof / ceiling etc complete all as directed. Note : (i) Cost of Porcelain insulators and screw shall be of non-corrosive type and cost is deemed to be included in the quoted rate of the job. (ii) Gap for fixing of support insulator shall not be more than 35cm from one onother.

Supply & Fixing air termination Copper rod 12 mm dia, 300 mm long for lightening conductor including base plate with all necessary nut bolts and drilling job etc.complete all as specified and directed.

Supply & fixing for Aluminium strip 25 x 3.15mm on wall/ roof/ batten or recessed or buried in ground including all insulators, screw, nut bolts with saddles and fixing for roof conductor and down conductor complete all as directed by Engineer-in-Charge.

M&L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 nos. 8 mm dia, 25mm long head screw complete all as specified and directed.

Supply and fixing of GI pipe light grade of size 40 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground with top edge of the plate not less than 1.5 mtrs below normal gound level and connected to earth test point by means of galvanised MS strip 25 x 4 mm as earthing lead all as specified and shown in electric plate No 3 of MES SSR Part-I 2009 including earthwork, PCC chamber, CI cover, protection and watering pipe, funnel, mesh etc all as required at site and all as directed. Note: (1). 7.5 RM GI strip in deemed to be included in quoted rates beyond 7.5 RM strip shall be measured and paid separately (2). Earth resistance of earth pit should be less than 0.5 Ohms. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. (3) Rate quoted by the tenderer is deemed to include salt & Charcoal upto & above 450 mm top of Copper plate.

M&L for painting on wall with synthetic enameled paint of black colour of 200 x 150 mm size and writing work for earth test result with date & year all as specified and directed at site by Engineer-in-Charge.

M&L for cutting/boring of PCC / WBM / hard standing at a depth not more than 30 cm deep & 20 cm in breath and making good disturbed surfaces as it was existing by using the same new materials on cutting areas/ disturbed surfaces complete all as specified and directed.

Modular blank plate 1 module suitable for modular switch board all as specified and directed

Modular blank plate 12 module suitable for modular switch board all as specified and directed

Modular blank plate 8 module suitable for modular switch board all as specified and directed

Modular blank plate 6 module suitable for modular switch board all as specified and directed

Modular blank plate 3 module suitable for modular switch board all as specified and directed

Joy builders (BID ID -3121153)

mp construction co (BID ID -3122154)

Vishal Builders (BID ID -3121136)