8221 CERTAIN SPECIAL REPAIR WORKS TO THE BUILDINGS IN THE AREA OF AGE BR-II UNDER GE SOUTH PUNE

Amount

Dismantling plain or corrugated, steel sheeting /AC Sheet of any gauge., thickness in roof coverings complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F Rolled Mild Steel roof trusses (framed), trussed, purlins ,rails and fastenings etc., confirming to Fe 410 - S including distance pieces, cleats, etc., complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an clour having tensile strength of 550Mpa asm in roof covering/cladding to wall, fixed with selt tapping screws complete all as specified and as directed.

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strengh of 550 mpa as of roof covering/ridges fixed with self tapping screws complete all as specified & directed.

Dismantling boarding/ceiling of any description, fixed in any position like partition etc with nails including frame work of timber complete all as specified and as directed>

M&L for Gypsum ceiling board for ceiling prepainted, perforated finish, 595 x 595 x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light at as specified and directed.

Taking down chowkat with shutter without taking out shutter from the frame n.exc 1.5 Sqm complete all as specified and as directed.

Taking down chowkat with shutter without taking out shutter from the frame exc 1.5 and n.exc 4 Sqm each complete all as specified and as directed.

M&L for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section including glass and stainless steel wire mesh etc complete all as specified and directed. (a) SP 20048 (b) Glazing clips 19352

S&F three track sliding window with two or more shutter with 4mm thick tinted glass one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed. (Make : Hindalco/Indal/Ajit India pvt ltd) (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S&F floor door stopper, aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm size overall of ISI mark.complete all as specified and as directed.

S & F Solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS tube, suppling and fixing in opening complete all as per specification and as directed

S&F factory made solid panel PVC door shutter 30mm thick (styles) consisting of frame made cut of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelaminated PVC sheet 5mm thick for top rail, lock rail and bottom rail and stile and rails having one side feathered edge, on other side 10mm 900 bent edge, panelling to be fitted in MS frame welded/sealed to the stiles and rails and 15mm thick PVC sheet beading inside and decorative PVC beading of 10mm x 10mm all as specified and directed and as per product Drg given on Sl. Page No. 184 of SSR Part-II 2010 (Refer item No. 8080) as specified and directed.

S& F 105 x 60 mm size Pressed steel frames 1.25mm thick for doors with one rebate including necessary fixing lugs, hinges, lock strike plate, etc, complete as specified and directed.

S& F 125 x 60 mm size Pressed steel frames for doors with two or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

S& F 165 x 60 mm size Pressed steel frames for doors with two or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

S & F 35 mm thick Factory made Second class hard wood Glazed and skeleton shutters, open rebated divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc ; sizes of members of shutters as specified in SSR Part I, Section 8, cla-use 8.20 (a); supplied and fitted to chowkats

S & F 35 mm thick factory made second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (Two panels) with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces, complete as specified and directed.

S&F IInd class hard wood small ffittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours, article not exc 200 cucm each, complete as specified and directed.

Supply and fixing 100 mm butt hinges medium weight cold rolled mild steel ISI marked fixed by welding to the pressed steel door frame as in repairs, complete as specified and directed.

Supply and fixing 200 mm aluminium anodised barrel tower bolts of extruded section, ISI marked and fixed with steel screws, complete as specified and directed.

S&F for aluminium alloy anodised sliding door bolt with hasp staple (bolt type) length 300mm complete all as specified and as directed.

S & F Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples, complete all as specified and directed.

All as per item No 24.00 above but fixed in repairs complete all as specified and as directed.

S & F 100 mm butt hinges, extruded aluminium alloy type B-21 with galvanised mild steel ISI markedhinge pin, anodised and fixed with wooden screws complete as specified and directed.

S & F butt hinges 100mm size stainless steel medium weight complete all as specified and as directed.

S&F Aluminium anodised 150mm handle cast type, complete as specified and directed.

S&F aluminium anodised barrel tower bolt 200mm legth of extruded section and fixed complete all as specified and as directed.

S&F aluminium alloy sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 300 mm of ISI mark complete all as specified and directed

Dismantling of stone slabs and tiles of any description or thickness in floor apron etc laid bedded and pointed in cement mortar complete all as specified.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for

M&L for 25 mm thick plain cement concrete type B-1, (1:2:4) ( 20 mm graded stone aggregate ) as in floors complete all as specified and directed.

M&L for granite 18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in CM (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and as directed.

Rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed.

M&L for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete incl 10mm thick rendering in CM (1:3) backing of wall tiles such as dado/skirting in vertical surface complete all as specified and directed.

S & F Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) complete all as specified and as directed.

M & L for coloured non skid ceramic tiles 7 to 8mm thick of size 300 x 300 in floor etc set & jointed in neat cement slurry and poited in white or coloured cement to match fixed over and including screed bed or bedding layer 15mm thick in CM 1:6 all as specified and directed .

M&L for 400 x 400 x 8 mm thick, joint free, non skid ceramic coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20mm thick screed bed in CM 1:6 complete all as directed.

Material and labour for coloured glazed ceramic tiles of size 300mm x 600mm x 7 to 8mm thick of colour and pattern as approved by EIC, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over back coat complete all as specified and as directed.

M & L for Coloured Ceramic tiles 9 to 10mm thick (Square/rectangular) of size 600 x 600 mm in floor etc set & jointed in neat cement slurry and poited in white or coloured cement to match fixed over screed bed or bedding layer complete all as specified and directed. (Make : Kajaria/Johnson/Somany or equivalent)

M&L for Screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified and directed.

M&L for backcoat of 10mm thick in CM 1:4 complete all as specified and directed.

Dismantling unserviceable PVC water storage tank of 500 Ltr capacity, complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks 500 lts (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 complete all as spoecified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed. (Note :- Cleaning repairing, etc. measured separately)

S&F 20mm bore ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferule complete all as specified and directed.

All as per Sl. item No. 47.00 above but fixed in repairs complete all as specified and as directed.

Demolition of stone / block masonry /brick masonsy built in CM complete all as specified and as directed.

M&L for Brick work with Fly ash brick, straight or curved on plan exc 6M Mean radius built in type CM 1:6 complete all as specified and directed by Engr-in-Charge.

Taking down cement or cement lime plaster on brick or stone wall etc. incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar (1:6) on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 15 mm rendering in cement mortar (1:4) using water proofing compound @ 2% by weight of cement in finish coat on other than fair faces of brick wall surfaces, finished even and smooth without using extra cement complete. (Note:- water proofing compound shall be measured and paid separately.)

M & L for 2mm thick wall care putty on wall complete all as specified and directed.

M&L for Complete removal of existing treatment on walls by scrapping washing rubbing down etc and applying two coats of Exterior emulsion paint over a coat of primer complete all as specified and as directed.

M&L for Preparation of new plastered surfaces of wall and applying two coats of Exterior emulsion paint over a coat of primer complete all as specified and directed

Preparing newly plastered surfaces of walls and applying two coats of weather proof acrylic emulsion paint over a coat of alkali resistant primer complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of weatherproof exterior emulsion over a coat of primer complete all as specified and as directed.

All as per Sl. item No. 58.00 above but applying two coats of white wash on walls complete all as specified and as directed.

Complete removal of exisitng treatment and preparation of old decorated surfaces of wall by brooming down & scrapping wherever necessary and applying two coats of OBD over a coat of alkali resistant primer including 2mm thick wall care putty complete all as specified and as directed.

M&L for Two coats of Oil bound distemper including prepration of newly plastered/putty wall surface complete all as specified and as directed.

M&L for Preparation of old steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified & directed.

M&L for preparation of new steel surface of any description not otherwise described over 10 cm width or girth and applying, two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed

S&F vitrous china wash hand basin white 400x400mm flat back inclduing and providing waste pipe 40mm dia medium grade, CP brass waste coupling 32mm dia with check nut washer etc fixed in repairs complete all as specified and directed. (Make : Cera of Cat no S2020123 or equivalent model in) Hindustan Sanitary Ware Industries (1st quality) (Hindware only) /Parry Ware (Super fine) as approved by GE)

S&F 40mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 15mm bore complete all as specified and as directed.

Cutting chases, pinning in, making good to fancings where required and pointing in cement mortar 1:3 to edges or edges of landings, steps, cills etc and cutting chase for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10 cm girth in Brick walls complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 20mm bore complete all as specified and directed.

M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and as directed.

M & L for GI tubing 20 mm dia medium grade with all fitting & fixed complete to wall & Ceiling or laid in floor complete all as specified and as directed.

S&F in repair cast iron Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs bib tap of cast copper alloys with crutch or butter fly handle screwed down screwed for iron pipe or for brass fenule and fixed for 15mm dia pipe inclduing removing the old unserviceable bib taps fixed complete all as specified and as directed.

Supply & fix 15mm bore pillar tap fancy type, cast copper alloy with capstan head, chromium plated screwed down, high pressure with or without lettered “hot “ or “cold” with long screwed shanks and fly nut complete all as specified and directed.

Supply and fix in repair 15mm stop valve fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends of, complete all as specified and directed.

S&F high density 40mm bore polythylene pipes (HDPE) of pressure rating 6 kg/cm2 fixed complete to wall or in floors with necessary socket, elbow & bend etc complete fixed to wall or in floors etc complete all as specified & directed. (Note : pipe will be laid under floor)

S&F in repairs vitreous China squatting pan, 'Orrissa' pattern, size 580xmmx440mm white, with integral foot rests (excluding flushing cistern, flush pipe and waste pipe) and ‘P’ or ‘S’ trap front or back inlet including concrete bedding, complete all as specified and direrected.

S&F in repair stop valve chromium plated fancy type with long shank and cup (concealed type) cast copper alloy screwed down high pressure with capstan head or butterfly handle screwed both ends for iron pipe or for unions and fixed in repairs complete 15mm dia complete all as specified and directed. (Make : Cera/Parryware as approved by GE)

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mmcomplete all as specified and directed. (Make : Cera/Parryware as approved by GE).

S&F in repair steel grating 150mm size of ISI mark complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair aluminium powder coated decorative type curtain rod 20mm dia complete all as specified and as directed

S&F in repair aluminium powder coated decorative type curtain rod 25mm dia complete all as specified and as directed

S & F aluminium powder coated brackets suitable for 20mm dia curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed

M&L for 75mm thick cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection including forming joint to full depth at every 3.0m interval and at every change of direction and filled with mixture of bitumen and sand (1:3) by weight, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 mtr depth n exc 10 sqm on plan and getting out in hard / dense soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for reinforced concrete pipes, 150 mm bore, class NP-2 laid and jointed with collars complete all as specified and as directed.

M&L for precast cement concrete 1:2:4, type B1 (Using 20 mm graded granite stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm in soils complete all as specified and as directed.

Removing excavated material exc 250 m & not exc 500m in soils complete all as specified and as directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, coupling, waste pipe and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repair Chromium plated shower rose 125 mm size with swivel joints including fixing to steel pipe or union as in repair, complete all as specified and directed.

S&F for Stainless steel plate rack of size 600x750x25 mm of approved quality complete all as specified and directed. (Make - Nirali/Diamond or of equivalent make specified here in after)

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supply and fix in repair 20mm bore Gun metal gate valve with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

Dismantling of CI / AC/ PVC pipes of various dia jointed in CM or adhesive 75 to 100mm dia complete all as specified and as directed.

Supply and fixing (SWR) pipe single socketed in any length with rubber ring joints laid in floor for 110mm bore of 6kgf/cm2 capacity complete all as specified and as directed.

All as per item No. 102.00 above here-in-before but 75mm bore of 6kgf/cm2 capacity complete all as specified and as directed.

Supply and fixing PVC (SWR) pipe single socketed in any length with rubber ring jounts fixed to walls for 110mm bore of 6kgf/cm2 capacity complete all as specified and as directed.

All as per Sl. Item No. 104.00 above but 75mm bore of 6kgf/cm2 capacity complete all as specified and as directed.

Supply and fixing PVC (SWR) junction single (singleT) equal or unequal nomminal bore in mm joints fixed to walls for 110mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75 mm bore complete all as specified and as directed.

Supply and fixing PVC Bends any radius 110mm bore complete all as specified and as directed.

All as per item No. 108.00 above but 75mm bore complete all as specified and as directed.

Supply and fixing PVC vent cowl 110mm dia complete all as specified and as directed.

M & L for 25 mm thick PCC (1:2:4) type B0 (12.5mm graded stone aggregate) as in leveling course of floor tiles etc complete all as specified and directed.

M&L for coloured vitrified tiles 600 x 600 x 8 mm thick as in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for coloured vitrified tiles 600 x 100 x 8 mm as in skirting/dados, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 10mm thick backing coat in CM (1:4) including triangular filleting in CM 1:4 on top of tiles complete all as specified and directed.

M&L for coloured Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 20mm thick screed bed in CM (1:6) complete all as specified and directed.

S & F Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for 19mm thick prelaminated particle board both side decorative face, including providing second class hard wood 6mm thick beading for edges of board alround all as specified and directed.

S&F in repairs 40 mm dia polished hardwood cupboard Knobs fixed with nuts, screws and washer of brass polished complete all as specified and as directed.

S & F in repair contionous hinges MS bright finish or electro galvinised with of flaps 30mm complete all as specified and as directed.

S&F in repairs Magnet catches and striking plate complete all as specified and as directed.

Taking down shutters of any description not exc 1 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 Sqm each complete all as specified and as directed.

S & F 35mm thick flush shutters, solid core construction, with block board core and plywood face panells commercial type on both faces incl 6mm thick Ist class HW (Teakwood) beading all around on edges complete all as specified and as directed.

S & F butt hinges 75mm size MS cold rolled medium weight complete all as specified and as directed.

S&F aluminium anodised handles, fabricated type, of size 150 mm complete all as specified and as directed.

S & F 300mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18 mm & fixed with stainless steel wire staples complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level) un-reinforced complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:6 on concrete surfaces finished with sagol finish to plasterred surface by using readymix plaster complete all as specified and as directed. (Make :- Godrej,Buildwell,Ascolite)

Rendering 12mm thick in cement mortar 1:4 on fair faces of PCC block walling using water proofing compound as per manufacturers instruction surface finished with sponge finish complete all as specified and as directed. (Make :- Godrej,Buildwell,Ascolite)

Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Prepration of old decorated surfaces of walls by brooming down and scrapping whereever necessary and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for applying three coats of white wash on ceiling and incl. preparation of new plaster surface complete all as specified and as directed.

Dismantling of structural steel work including doors,gates but excluding framed Truss etc complete all as specified and as directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F (SWG) gully trap 150mm setting and jointing with solvent cement complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (wall, ceilings, floors etc) for the following :-

15mm bore

20mm bore

S&F in repairs vitreous china wash down water closet pan, 'Pedestal' white, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge devices including PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.

S&F in repairs vitreous china, squatting pan, 'Orissa' pattern, size 580 x 440mm white, with integral foot rest, including concrete bedding and PVC flushing cistern 10 Ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.

S & F in repair for Wash Hand basins, Vitreous China, white, flat back, size 550x400mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing of supply, waste pipe, taps) complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm in repairs.

S&F looking mirror of size 600 x 450mm approved quality and make , mounted on 6 mm thick plywood commercial as backing and aluminium powder coated frame all around on edges complete all as specified and as directed.

S&F, in repair, CP stop valve 15mm dia cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes for unions complete all as specified and as directed.

Taking down steel window/ventilators leaf and making the disturbed surface good as specified and directed.

S&F fixed glass ventilators using 5mm thick plain glass & following aluminium powder coated sections conforming to Cat Part No. Jindal or of equivalent make & rubber beading etc complete all as specified and as directed. (a) SP-20048 (b) Glazing clips - 19352

M&L for providing and fixing CP toilet fitting in repairs as specified and as directed by the Engr -in-Charge for the following:-.

CP towel rail 20mm dia and 600mm long including brackets conforming to CAT No. ACN-1111N of "Jaquar" or of Equivalent make specified here in after

CP towel ring conforming to CAT No. ACN -1121 N of "Jaquar" or of Equivalent make specified here in after

CP 15mm bore concealed stop cock with long neck conforming to CAT No. CON-069 of "Jaquar" or of Equivalent make specified here in after

S&F in repair 8 mm thick corner glass with D bracket complete all as specified and as directed.

M&L for 12 mm thick rendering on fair faces of brick/concrete/block wall surfaces in CM 1:6, including finishing the surfaces fair and even, complete all as specified and directed.

S&F in repair 18 mm thick MDF board prelaminated both side with decorative choice lamination as in Kitchen Cabinet,pelmate box,drawer, CB shutter etc fixed with screw including 6mm thick, 1st Class HW (TW) beading all around on edging to timber frame work all as specified and directed.

M & L for IInd class hard wood Wrought plain fillets square, rectangular or triangular in section clean sawn secured with screws, sectional area exc. 13 Sqcm but n. exc 25 Sqcm etc complete including dismantling of timber fillets in cabinet/cupboard frame complete all as specified and directed.

S&F in replacement 100 mm brass fancy type cupboard handle fixed with nuts, screws and washer of brass polished complete all as specified and directed.

S & F Fe 410-0 or Fe 310-0 framed work as in door or gates of angle or other section with guest plates rails , braces, etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, fastening, etc complete all as directed.

Demolition of cement concrete of any description and in any position complete all as specified and as directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone agg as in coping, on top of wall, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary form work complete all as specified and as directed.

Taking down rain water pipes,110mm/75mm dia drain pipes of any description of any pattern incl all fittings heads, shoe bends etc. complete all as specified and as directed.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of white wash on walls complete all as specified and directed

Complete removal or existing treatment and preparation of old decorated surfaces of wall by brooming down and scraping where ever necessary and applying two coat of Oil Bound Distemper over a coat of Alkali resistant primer and 2mm thick wallcare putty all as specified and directed

Taking up or down carefully steel tubing and connections including cleaning for refixing of following sizes 25mm bore complete all as specified and as directed.

S&F GI tubing tubes "medium grade" galvanized with all fittings and fixed complete to walls and ceiling or laid in floors etc. of the following sizes 25 mm bore complete all as specified and as directed.

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20mm bore complete all as specified and as directed.

M & L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course filling around Nahani trap etc and in similar situations complete all as specified and as directed.

M&L for double charge coloured vitrified tiles 1000 x 1000mm x 9 to 10mm thick as in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for double charge coloured vitrified tiles1000 x 100mm x 9 to 10mm thick ,as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 10mm thick backing coat in CM (1:4) complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base / flooring complete all as specified and as directed.

S&F in repairs single piece WC with seat cover with all fixing accessories set and cistern fittings complete all as specified and as directed conforming to Cat Part No. SLS-WHT-6851S110PP of M/s Parryware or of equivalent make in Hindware

S&F in repairs vitreous china wash hand basin, white flat back of size 550x400mm including 15mm CP pillar tap, PVC waste coupling 32mm, chain and plug and CP bottle trap, PVC connection 45cm long including CI brackets/fixing with fasteners etc complete in repairs all as specified and directed. [Make :- (i) WHB with Pedestal - Parryware Valdarno series Cat Part No. C0405 & C0317 or of equivalent make in Hindware. (ii) CP Pillar Tap - Jaquar Cat Part No. ARI-CHR-39011 or of equivalent Make in MARC (iii) CP Bottle trap - Jaquar Cat Part No. ALD-CHR-769 (200 x 300) or of equivalent make in MARC]

M & L for PVC (SWR) floor trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

M & L for filleting in any position and to any shape in CM 1:3 sectional area exc. 25 Sqcm but n.exc. 50 Sqcm complete all as specified and as directed.

S&F in repairs angle cock cast copper alloy, CP 15mm bore, screwed down, high pressure with crutch or butterfly handle, conforming to Cat Part No. ARI-CHR-39053 of Jaquar or of equivalent make in MARC complete all as specified.

S&F in repairs Wall mixer 3-in-1 including telephone shower for 15mm bore of pipe conforming to CAT No CON-267 of "Jaquar" or Equivalent make specified here in after.

S&F in repairs Bib taps CP 15mm bore fancy type conforming to CAT No CON-039 of "Jaquar" or Equivalent make specified here in after.

S&F in repairs CP towel rail 20mm dia and 600mm long including brackets conforming to CAT No CAN-1111N of "Jaquar" or equivalent make here in after.

S&F in repairs CP toilet paper holder confirming to CAT No CAN-1151N of "Jaquar" or Equivalent make here in after complete all as specified and as directed.

S&F in repairs CP Soap dish confirming to CAT No CAN-1131 of "Jaquar" or equivalent make here in after complete all as specified and as directed.

S&F in repairs Corner glass shelves with brackets CAT No CAN-1173 of "Jaquar" or equivalent make here in after complete all as specified and as directed.

S&F in repairs CP shower rose 125mm dia with arms for 15mm bore of pipe conforming to CAT No OHS-489 of "Jaquar" specified here in after.

S&F in repairs Two way Bib taps CP 15mm bore fancy type conforming to CAT No. CON-041KN of "Jaquar" or of Equivalent make specified here in after.

S&F in repairs CP health faucet with flexible pipe fancy type complete all as specified and directed. [Make : Jaquar Cat Part No. ALD-CHR-565GA or of equivalent make in MARC]

S & F IInd class hard wood 35mm thick factory made, glazed and skeleton shutter open rebated and prepared to receive glass,gauge,etc.edges of framing plain,chamfered or rounded fitted with cut and mitred beads for securing glass,etc; The size of the rail and stile as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated.

M&L for 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm and over in section in any position (unframed work) complete all as specified and as directed.

Dismantling of timber scantling as in fillets,rails, posts, rafters, purlins under 40 sq cm in section(framed work) complete all as specified and as directed.

Dismantling wall and ceiling boards , any thickness, including cover fillets complete all as specified and as directed.

Supply and fixing PVC FALSE CEILING consisting of 600mmx600mm,5mm thick plain embossed PVC sheet of 600kg/cbm Density manufactured by as ISO-9001-2008 certified company,used as panel insert in aframe work made using anodized aluminium T-section of sizes 25x25mm 19 gauge or 1mm thick in square pattern of grid of 600x600mm.The aluminium frame work is supported from the ceiling with 'J' hooks and G.I wire /6mm M.S rod of required sizes to maintain proper level etc .The aluminium frame work is supported on side wall with the use of aluminium L-section of size 25x25mm angles etc complete all as specified & directed. (Make : Rajshri/ GIZA or of equivalent make specified here-in-after)

S&F PVC wall panelling on thickness 5mm consisting of panels of desired size stuck on onner frame work of 50mm wide strips of 5mm thick prelaminated PVC sheet, The panel & strips shall be of 600kg/cum density manufacture by ISO-9000 certified company. Strips should have in their centre a groove of 6mm width and 1mm depth for shinking the head of the screw usrd to fix the strips to the wall vertically at an equal internal of 10" between two PVC strips. The PVC strips shall be fixed to the wall using 65mm long MS screws through the groove in the strip by using fasteners. The distance between two panel for asthetic looks. The exact size of the panel and corresponding of the grid may vary depending on the size of the wall. Optionally strips of 5mm thick sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined using solvent cement complete all as specified & directed. (Make : Rajshri/ GIZA or of equivalent make specified here-in-after)

Supply only integral water proofing compound complete all as specified and as directed.

Demolition of RCC (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for RCC nominal mix type B1 (1:2:4) using 20mm graded stone aggregate as in lintel, roof beam,chajjas, band etc. complete all as specified and directed.

M&L form work to sides and soffits of roof beam/Lintel beam, chajjas etc rough finished surface of concrete complete all as specified and as directed.

S&F MS TMT bars upto 10mm dia cut to length, bent to shape required including cranking, bending, binding, hooking ends abd binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for 12mm thick Plywood, grade BWR, type BB, as in cupboard, shelf etc fixed in repairs with screws to timber work complete all as specified and as directed.

S&F decorative type brass handle of size 200mm as approved by GE.

Removing of old water proofing treatment including screed bed and cleaning the surface of slab with wire brushes removing dust, foreign materials including flushing at junction of wall and removing the rubbish off the premises to a distance exc 500m all as directed by Engr-in-Charge

M & L Water proofing treatment to RCC roof slab, walls, chhajjas etc, shall be carried out as specified below and as directed. (a) M&L for 10mm thick plaster screed bed layer in CM 1:3 on concrete surfaces. (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bituminous primer @ 0.20 Kg/sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, 3mm thick non woven, polyester, weighing not less than 3.5 Kg/sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/sqm on the top of membrane surfaces complete all as specified & as directed by Engr in Charge

Labour only for Grinding mirror polishing of old Kota stone / Cement flooring in floor including rubbing and polishing complete all as specified and as directed.

Taking down carefully exising unserviceable aluminium point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making dood disturbed surfaces of wall, floor etc. complete all as specified and as directed.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including necessary making good the disturbed surfaces to match with the existing finishes complete all as specified and as directed.

Taking down of old unserviceable sub main wiring of any type complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following :-

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board

One bell point controlled by one, bell switch 5 Amps

All as per item No. 199.00 above but with stranded copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet on independent board including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed.

S & F for modular Bell push modular 6 Amps single module complete all as specified and as directed.

Suply and fix for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply including removal of old unserviceable one complete all as specified and as directed

S & F for Modular switch one way 6 Amps, 1 module complete all as specified and as directed.

S & F for Modular switch one way 16 Amps, 1 module, with neon indicator complete all as specified and as directed.

S & F for celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified and as directed.

S & F for modular step type fan regulator 120 watt single module suitable for operation on 230 volt 50 HZ AC supply complete all as specified and as directed

S & F for Modular socket, 6 Amps, 2/3 pin combination 2 module complete all as specified and as directed.

S & F for Modular socket, 6/16Amps, 2/3 pin combination 2 module complete all as specified and as directed.

S & F for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and as directed.

S&F vertical 8 way TPN double door recess mounted/wall mounted MCCB's as incommer is 3 pole V- Tec of 100 amps rating & 16 KA breaking capacity MCCB is pre fitted at factory & including price of MCCB all as directed and spd by engr in charge Cat Part No DBVTH004SD L&T equivalant to Havells/Legrand all as specified and as directed.

S&F MCB DB,SPN, sheet metal enclosure, 4 way with 200 amps rated bus bar double door, with locking arrangement fixed in wall including cutting & good to disturbed surfaces complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40-63 amps, 240 Volts breaking capacity 10 KA complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 amps, 240 Volts breaking capacity 10 KA complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6.0 Sqmm nominal area and drawing into PVC non metallic rigid PVC casing caping including one run of PVC insulated 6 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. (Note:- Three runs of 6.0 sqmm cable and one run of PVC casing caping will be measured as one unit.)

All as per Sl. Item No. 215.00 above but copper conductor of size 4.0 sqmm nominal area complete all as specified and as directed. (Note:- Three runs of 4.0 sqmm cable and one run of PVC casing caping will be measured as one unit)

S & F wall mounted LED 20 watts , LED batten for surface and pendant application, Anodized extruded aluminium housing, high transmissitivity diffuser and high lumen output, 230 volts etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. (Make :- Bajaj Cat part No BCLAB 20W or its equavalent in Philips, Wipro, Havells. all as specified and as directed.)

S & F for LED 10 watts batten aluminium extruded with decorative end caps including removal old unserviceable T8 type light fitting complete all as specified and as directed. (Make- Bajaj Cat Part No BCLSB 10 WH, Wipro Cat part No LL20-111-XXX-65-NE or its equvalent in Philips, Havells all as specified and as directed.)

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and including provosion of LED bulb 10/11 watts complete all as specified and as directed. (Make- Havells Cat part No -LHGLO6160099 or its equivalent in Wipro, Philips, Bajaj)

Taking down ceiling fan of any size/sweep after disconnection the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing etc including provinding flexible three core wire of size 23/.0076 from ceiling rose to connector of fan all as specified and as directed.

S & F for metal body exhaust fan, AC single phase, heavy duty, turbo force 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. (Make - Bajaj Cat Part No -Maxma DX 8" or its equivalent in Crompton/Havells)

M & L for Earthing complete with galvanised steel earth plate electrode 60cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm as earth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 3, SSR Part I- 2009 with 15 mm dia medium grade GI pipe as a protection and 20 mm dia medium grade GI pipe for watering purpose inlcuding funnel, wire mesh, RCC pit with cover complete and connected to earthing test point all as specified or indicated including testing on completion all as specified and as directed.

S&F industrial metal clad socket 2P+1N complete with metal clad 3 pin top and MCB SP 32A in sheet metal enclosure all as specified and directed.

Gauri Associates

Raj Construction Company

M/S DSSK ENGINEERING AN DCONSTRUCTION

M/s.BAJRANG CONSTRUCTION