A/R and M/O Circle Office Building at Hamirpur

Amount

Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m (One point five metre) in width or 10 sqm (Ten square metre) on plan), including dressing of sides and ramming of bottoms within all leads including getting out the excavated soil and disposal of surplus excavated soil as directed, within all leads and lifts oridinary rock and all kinds of soil including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position mechanically mixed and vibrated cement concrete of 1:3:6 (one cement : three coarse sand : six graded stone aggregate) 20mm ( twenty millimetre) nominal size graded stone aggregate for all works upto plinth level excluding the cost of centering and shuttering including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Centering and shuttering including strutting, propping etc. and removal of form work for including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Columns, piers, abutments, pillars, posts and struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access plat form

Edges of slab and break in floors and walls under 20cm ( twenty centimetre) wide

Stairs, (excluding landings) except spiral stair cases

Providing and laying in position mechanically mixed and vibrated cement concrete of 1:2:4 (One cement : Two coarse sand) : four graded stone aggregate 20 mm (Twenty millimetre) nominal size) size) for All work up to plinth level excluding the cost of centering and shuttering including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position specified grade of M-25 (M-Twenty five) design mix with minimum crushing strength of 25N/mm2 (Twenty five Newton per millimetre square) using graded stone aggregate 20 mm (twenty millimetre) nominal size with minimum cement content not less than 400.00kg/cum (Four hundred kilogramme epr cubic metre) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement mechanically mixed and vibrated and curing complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying design mix reinforced cement concrete of M-25 (M-Twenty five) grade with minimum crushing strength of N/mm2 (Twenty five Newton per millimetre square) with minimum cement content not less than 400.00 kg/cum (Four hundred kilogramme per cubic metre) , using graded stone aggregate 20 mm (twenty millimetre) nominal size) in beams, suspended floors, roofs having slope up to 15° ( fifteen degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, stair cases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement and mechanically mixed and vibrated, curing complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Steel reinforcement (TATA/JINDALPANTHER/SAIL make) for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all level TMT Bars Thermo-Mechanically Treated bars of grade Fe-500D or more including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five) in super structure above plinth level up to all floor level in all shapes and sizes Cement mortar 1:6 (one cement : six coarse sand) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in super structure above plinth level up to all floor level in cement mortar 1:4 ( one sand : four coarse sand) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) Sal wood complete including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 40mm ( forty millimetre) thick second class teak wood panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge (Butt hinges and necessary screws shall be paid separately) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing 40mm ( forty millimetre) wire gauge shutters of 2nd ( second) class teak wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm ( one point four millimetre) in both directions with wire of dia 0.63 mm,( zero point six three millimetre) for doors, windows and clerestory windows with hinges and necessary screw with ISI marked M.S. pressed butt hinges bright finished of required size including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing M.S. grills of required pattern in frames of windows etcetera with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to opening/wooden frame with rawl plugs screw etcetera including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Float glass panes of nominal thickness 5 mm ( five millimetre) make of Modi Float, Saint Govind, Aashai (weight not less than 12.5kg/sqm ( twelve point five kilogram per square metre) of renewing glass panes with putty and nails wherever necessary including racking out the old putty including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

300x16mm (Three hundred into sixteen millimetre) nominal size.

250x16mm (Two hundred fifty into sixteen millimetre) nominal size.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

200x10mm (Two hundred into ten millimetre) nominal size.

150x10mm (One hundred fifty into ten millimetre) nominal size

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

125mm (One hundred twenty five millimetre)

100mm (One hundred millimetre)

Providing and fixing 25mm ( twenty five) dia chromium plated brass curtain rod having wall thickness of 1.25mm ( one point two five millimetre) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etcetera wherever necessary complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing 150 mm ( one hundred fifty millimetre) bright finished brass hard drawn hooks and eyes including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying 600x600 mm ( six hundred into six hundred millimetre) full body charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( zero point zero eight percent) and conforming to IS: 15622, of Orient Bell/ Kazaria/Rak/Johnson & Johnson approved make, in all colours and shades, laid on 20mm ( twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three point three per kilogram per square metre) including grouting the joints with white cement and matching pigments etcetera complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Kota stone 25 mm ( twenty five millimetre) thick flooring in treads of steps and risers using single length up to 1.2 mtr. ( one point two metre) over 20 mm ( twenty millimetre) (average) thick base of cement mortar 1:4 ( one cement : four coarse sand) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying 18 mm ( eighteen millimetre) thick Polished Granite stone slab (Jet Black, Cherry Red, Elite Brown, Cat Eye colour) flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etcetera all complete as specified and as directed by the Engineer-in-Charge.Polished upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying matt finished vitrified tile of size 300x300 x 9.8mm ( three hundred into three hundred into nine point eight millimetre) having with water absorption less than 0.5% ( zero point five percetage) and conforming to IS: 15622 of Orient bell, Kajaria, NITCO, Somany, RAK, Johnson & Johnson approved make , in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etcetera, laid on 20mm ( twenty millimetre) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes and patterns including grouting the joints with white cement mixed with matching pigments etcetre complete upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying 300x450mm/300x600 mm (three hundred into four hundred fifty millimetre oblique three hundred into six hundred millimetre) digital glazed rectified HD Series ceramic wall tiles (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( zero point zero eight percent) and conforming to IS: 15622, of approved make (Orient bell/ Kajaria/RAK/AGL) in all colours and shades,in skirting, risers of steps and dados over 12 mm ( twelve millimetre ) thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm ( three point three kilogram per square metre) including pointing in white cement mixed with pigment of matching shade complete in pattern finish approved by the Engineer-in-Charge upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) (TATA/JSW Make) 0.50 mm ( zero point five zero millimetre) + 0.05 % ( zero point zero five percent) total coated thickness with zinc coating 120 ( one hundred twenty) grams per square metre as per IS: 277, in 240 ( two hundred forty) mpa steel grade, 5-7 ( five to seven) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns. Sheet should have protective guard film of 25 ( twenty five) microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 ( twelve) metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size 5.5x 55 mm ( five point five into fifty five millimetre) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Ridges plain 500 - 600mm ( five hundred to six hundred millimetre) precoated galvanised steel sheet roofing accessories (TATA/JSW Make) 0.50 mm ( zero point five zero millimetre) + 0.05 % ( zero point zero five percent) total coated thickness, Zinc coating 120 ( one hundred twenty) grams per square as per IS: 277, in 240 ( two hundred forty) mpa steel grade, 5-7 ( five to seven) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen ) microns using self drilling/ self tapping screws complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Crimp curve precoated galvanised steel sheet roofing accessories TATA/ JSW Make 0.50 mm ( zero point five zero millimetre) + 0.05 % ( zero point zero five percent) total coated thickness, Zinc coating 120 ( one hundred twenty) grams per sqm as per IS: 277, in 240 ( two hundred forty ) mpa steel grade, 5-7 (five to seven) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen) microns using self drilling/ self tapping screws complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Gutter 600 mm ( six hundred millimetre) over all girth precoated galvanised steel sheet roofing (TATA/JSW Make) accessories 0.50 mm ( zero point five zero millimetre) + 0.05 % ( zero point zero five percent) total coated thickness, Zinc coating 120 ( one hundred twenty ) grams per sqm as per IS: 277, in 240 (two hundred forty ) mpa steel grade, 5-7 ( five to seven ) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen ) microns using self drilling/ self tapping screws complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing Flashings/ Aprons Upto 600 mm ( six hundred millimetre) precoated galvanised steel sheet roofing accessories (TATA/JSW Make) 0.50 mm ( zero point five zero millimetre) + 0.05 % ( zero point zero five percent) total coated thickness, Zinc coating 120 ( one hundred twenty ) grams per sqm as per IS: 277, in 240 (two hundred forty ) mpa steel grade, 5-7 ( five to seven ) microns epoxy primer on both side of the sheet and polyester top coat 15-18 ( fifteen to eighteen ) microns using self drilling/ self tapping screws complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and fixing Single socketed pipes 110mm ( one hundred ten millimetre) dia of Supreme,Finolax,D-plast Vectus make on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimetre) gap for thermal expansion including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 110mm ( one hundred ten millimetre) dia of Supreme/Finolax/ Vectus make unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm ( fifty into fifty into fifty millimetre) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etcetera complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Structural steel work riveted, bolted or welded I.S.I. marked in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete in trusses, Purlins, Rafters and trussed purlins in building, in grating, framed quard bars, ladders, railing, brackets and similar works, in beams joists channels, angles tees flats. including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Steel work welded in built up sections (TATA/SAIL/JSW Make ) framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing mild steel tube hand rail ( TATA/SAIL/APOLLO) of approved size by welding etcetera to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Applying priming coat With ready mixed pink or Grey primer (ASAIN,NEROLAC,ICI-DULUX, ) of approved brand and manufacture on wood work (hard and soft wood) paint including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Painting two or more coats on new work with synthetic enamel paint ASAIN,NEROLAC,ICI-DULUX, ) of approved brand and manufacture to give an even shade complete as per direction of Engineer-In-Charge including entire carriage of material within all leads and lifts and other incidentals. The rates are inclusive of octroi, royalty, malakana, toll tax, sale tax, GST or other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (at the rate of zero point nine zero per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (at the rate of zero point eight zero per ten square metre) (ASIAN Paints, NEROLAC, ICI, DULUX) of approved brand and manufacture including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

15 mm ( fifteen millimetre) cement plaster on rough side of single or half brick wall of mix 1:6 ( one cement : six coarse sand) upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

20 mm (twenty millimetre) cement plaster of mix 1:6 ( one cement : six coarse sand) upto all floor level including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1 mm ( one millimetre) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm ( at the rate of one point six seven litre per ten square metre) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm ( at the rate two point two zero kilogram per ten square metre) of ASIAN (APEX ULTIMA) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Wall painting Two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type) of size 385 x 675 x 780 mm with white solid plastic soft closing seat and lid of Jaquar (ECS-WHT-7751SS+ECS-WHT-201) /Hindware Snow White Shade ,10 (ten ) litre low level white vitreous china flushing cistern and C.P. flush bend with fittings and C.I. brackets, 40 mm ( forty millimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm ( one hundred millimetre) sand cast Iron P or S trap, 10 ( ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C.pan of size 580x440 mm ( five hundred eighty into four hundred forty) with integral type foot rests Hindware /Cera (Universal Pan No. 2071) ( two thousand seventy one) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing White Vitreous China wash basin ( CNS-WHT-705 ) of Size (mm) 200 x 595 x 420 with C.I. brackets, 15 mm CP Brass single hole basin mixer of Jaquar (CON-CHR-167B) / Hindware 32 mm (thirty two millimetre) C.P. brass waste of standard pattern , including painting of fittings and brackets, cutting and making good the walls wherever required including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of Hindware/ Jaquar / Cera make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 510x1040mm (five hundred ten into ten thousand forty millimetre) bowl depth 250mm (Two hundred fifty millimetre) Stainless Steel AISI 304 (8/18) kitchen sink with drain board of Diamond ( REK 4520 )/Hindware 304 Grade Steel (Glossy Finish), as per IS:13983 with C.I. brackets and stainless steel plug 40mm (Forty millimetre), including painting of fittings and brackets, cutting and making good the walls wherever required including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetre) dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings Flexible pipe complete including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing CP soap Dish Holder with concealed fitting arrangements of Jaquar (ACN-1171N)/Hindware Make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 600 x 120 x 5mm ( six hundred into one hundred twenty into five millimetre) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm ( forty millimetre) long screws, rawl plugs etcetra, complete of Hindware /Jaquar / Cera make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing CP brass towel rail 600mmx20mm ( six hundred into twenty millimetre) long of Jaqaur ((ACN-111SM-7711) ) complete with CP brass brackets fixed to wooden plugs with CP brass screws including entire carriage of material with in all leads, lifts, technical specifications as per the direction by Engineer-in-Charge and other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm ( fifteen millimetre) dia C.P. brass bib cock with wall flange of approved quality conforming to IS standards of Jaquar ( CON-047KN) /Hindware Make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm ( fifteen millimetre) dia C.P. brass long nose bib cock with wall flange of approved quality conforming to IS standards of Jaquar (CON-CHR-107KN)/ Hindware Make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. brass stop cock for basin mixer and geyser points of approved quality conforming to IS:8931 of Jaquar ( CON-CHR-059KN)/Hindware Make including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimetre) dia nominal bore G.I. pipe of TATA/ JINDAL ( HISAR) complete with G.I. fittings and clamps, i/c cutting and making good the walls etc Internal work - Exposed on wall including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 20 mm (Twenty millimetre) dia nominal bore G.I. pipes of TATA/ JINDAL ( HISAR) complete with G.I. fittings and clamps, i/c cutting and making good the walls etc Internal work - Exposed on wall including entire carriage of material with in all leads, lifts, drawings, technical specifications as per direction by Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 110 mm ( one hundred ten milimetre ) dia Chromium Plated grating of superior quality for floor, gully or nahani trap including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing centrifugally Sand cast iron (S&S) as per IS - 3989 100 mm (one hundred millimetre) inlet and 100 mm (One hundred millimetre) outlet trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 75mm (seventy five) dia nominal size soil, waste and vent pipes centrifugally cast (spun) iron socketed pipe as per IS: 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 100 mm dia (one hundred millimetre) nominal size soil, waste and vent pipes Centrifugally cast (spun) iron socket and spigot (S&S) pipe as per IS: 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1.00 (one) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make ( Jaquare Opal series) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank,, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Sintex make Tripple Layers including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) nominal bore size ball valve (brass) of approved quality, High or low pressure, with plastic floats complete of Zindal /Tata make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing uplasticised PVC connection pipe with brass unions 45cm ( forty five centimetre ) length 15mm (fifteen millimetre) nominal bore Cera/Jaquar/ Finolex / hindware Make including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 600x450 mm ( six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) make of Atul,Modi Guard Golden Fish complete with 6 mm ( six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers completeof including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Provding and fixing 75mm (Seventy five millimetre) nominal size plain bend of required degree centrifugally sand cast iron (S&S) as per IS 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimetre) nominal size plain bend of required degree of centrifugally Sand cast iron (S&S) as per IS : 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 75x75x75mm ( seventy five into seventy five seventy five millimetre) nominal size single equal plain junction of required degree with access door, insertion rubber washer 3 mm (three millimetre) thick, bolts and nuts complete.Sand cast iron S&S as per IS - 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 100x100x100mm ( one hundred into one hundred into one hundred millimetre) nominal size single equal plain junction of required degree with access door, insertion rubber washer 3 mm (three millimetre) thick, bolts and nuts complete.Sand cast iron S&S as per IS - 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing centrifugally Sand cast iron (S&S) as per IS - 3989 75mm (seventy five millimetre) nominal size bend of required degree with access door, insertion rubber washer 3 mm (three millimetre) thick, bolts and nuts complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing centrifugally Sand cast iron ( S&S ) as per IS - 3989 100mm ( one hundred millimetre ) nominal size bend of required degree with access door, insertion rubber washer 3 mm (three millimetre) thick, bolts and nuts complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 75 mm (seventy five millimetre) nominal size collar Sand cast iron S&S as per IS - 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimetre) nominal size collar Sand cast iron S&S as per IS - 3989 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing 75mm (seventy five millimetre) nominal size lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing 100mm (one hundred millimetre) nominal size lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Supplying and fixing cast iron cover with other frame for manhole cast iron cover and frame 455x610mm(Four hundred fifty five into six hundred ten millimetres) (Light duty single seal pattern-I) internal dimensions total weight of cover and frame to be not less than 23kgs(Twenty three kilogramme) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge and including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm (twenty into twenty into ten centimetre) cement concrete blocks 1:3:6 (one cement : three coarse sand : six graded stone aggregate 20 mm (twenty millimetre) nominal size) as per standard design With 20x20 mm (twenty into twenty millimetre) square bar including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (onecement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design including cutting and threading the pipes complete Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg ( fifteen kilogram) With common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 (seven point five) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamberwith water tight C.I. cover with frame of 300 x300 mm (three hundred into three hundred millimetre) size (inside) the weight of cover to be not less than 4.50 kg (four point five kilogram) and frame to be not less than 2.70 kg (two point seven zero) as perstandard design square mouth trap 100 x100mm (one hundred into one hundred millimetre) ( size P-typeWith common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 (seven point five ) including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 150 mm (one hundred fifty millimetre) dia Ductile iron class K-7 (seven) pipes Centrifugally cast (spun) iron / Ductile iron pipes conforming to IS: 8329 including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Yash Paul