SPECIAL REPAIR TO BLDG NO. H-06 IN TIRAH LINE AND P-158 (TOILET BLOCK) AND P-214 (BATHROOM) IN BHARATPUR LINE AT MILITARY STATION DHARAMSHALA

Amount

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) area not exceeding 1.50 sqm each and removing complete, all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc.1.5 sqm but not exc. 4.0 sqm each all as specified and directed by Engr-in-Charge.

Solid PVC door frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as per drawing shown on page No 160 of SSR Part-II (rates) and as directed by Engr-in-Charge. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Factory made solid panel PVC door shutter 30 mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No. 156 of MES SSR Part-II 2010, complete all as specified and directed by Engr-in-charge.

All as per item No. 04 above, but wire gauzed shutter i.e panel will be of wire qauge in lieu of PVC sheet panel. The wire gauge shall be wrapped on an additional square 8mm solid tube and this tube shall welded to MS tubes. The wire gauge shall be stretched to tighten firmly, complete all as specified and directed by Engr-in-Charge.

Pressed steel door frame of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed by Engr-in-Charge.

Mild steel wire cloth of 0.63 mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, or galvanised wire staples in guazed steel windows all as specified and as directed by the Engineer-in-Charge.

100mm butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete, all as specified and directed by Engr-in-Charge.

150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete, all as specified and directed by Engr-in-Charge.

150mm long aluminium handles, cast type, anodised complete, all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water complete, all as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness laid in cement mortar complete all as specified and directed by Engr-in-Charge

Rendering 10 mm thick on other than fair faces of brick or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Rendering 15 mm thick on fair faces of brick or concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Rendering 20 mm thick on stone masonry surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Preparation of newly plastered or unplastered surfaces and applying three coats of white wash on walls Complete all as specified and directed by Engr-in-Charge.

Preparation of old & newly plastered wall surfaces and applying two coats of cement base paint including preparation of surfaces complete, all as specified and directed by Engr-in-Charge.

Glazed ceramic tiles premium class, grade-I in vertical surface of size 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls, complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors, in any position and pavings not exceeding 15cm thickness (below or above ground level) un-reinforced complete all as specified and directed by the Engr-in-Charge.

Plain Cement concrete, 25mm thick, M-15, type B-1(using 20mm graded crushed stone aggregates) as in floor complete all as specified and directed by Engr-in-Charge.

Mat finish (non skid) coloured tiles 7 to 8mm thick, straight edge, Premium Class I grade, area of each tiles exc.0.06 sqm but n.exc 0.11 sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-7.5 (nominal mix), type D-2 (using 40mm graded crushed stone aggregate) as in sub base, foundation, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-10, type C-1 (using 20 mm graded crushed stone aggregate) as in surface channel and drain Complete all as specified and directed by Engr-in-Charge.

Vitreous China wash hand basin, angle back, size 600x480mm white, including cutting for and pinning in ends of brackets or erecting stand, with 32mm chromium plated waste coupling, waste pipe of bore 32mm, PVC Connection pipe 450mm ling with brass nuts on both side, (fixed in repairs) complete all as specified and directed by Engr-in-Charge.

75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joint, laid in trenches / floor, complete all as specified and directed by the Engr-in-Charge.

PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joint, laid in trenches / floor, complete all as specified and directed by the Engr-in-Charge.

Taking up or down steel water tubing and connection, including cleaning for refixing or removal to store for 15mm bore tubing, complete, all as specified and directed by Engr-in-Charge.

GI tubing, medium grade, 15mm bore with all fittings/ fixtures, laid under floors/ trenches or fixed in wall complete, all as specified and directed by Engr-in-Charge.

GI tubing, medium grade, 20mm bore with all fittings/ fixtures, laid under floors/ trenches or fixed in wall complete all as specified and directed by Engr-in-Charge.

Re-fixing GI tubing, medium grade,15mm bore with all fittings/ fixtures, laid under floors/ trenches or fixed in wall complete, all as specified and directed by Engr-in-Charge.

Stop valve, 15mm bore, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions suitable complete, fancy type, chromium plated, complete all as specified and directed by Engr-in-Charge.

Bib taps 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type choromium plated and, complete all as specified and directed by Engr-in-Charge.

Shower rose, 125mm Chromium plated, with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed by Engr-in-Charge.

CP towel rail 20mm dia, 600mm long complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings dressed stone work and precast concrete articles, complete all as specified and directed by the Engr-in-Charge.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted built in CM 1:6 Complete all as specified and directed by Engr-in-Charge.

All as per item No 38 here-in-above but except stones.

Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:4 complete, all as specified and directed by the Engr-in-Charge.

Chequered cement concrete tiles of size 200X200X25 mm thick set, jointed and pointed in neat cement slurry as in floor with grey cement and pigment including 15 mm thick screed bed in CM 1:6 over 75mm thick PCC, M-10, type C-2 (using 40mm graded crushed stone aggregates), complete all as specified and directed by Engr-in-Charge.

Removal of existing roof treatment with steel wire brushing and cleaning top surfaces of cement concrete and removing demolished material to the distance not exceeding 50m complete all as specified and directed by the Engr-in-Charge.

10mm thick cement plaster in cement mortar 1:4 on concrete surface of roof or terracing surface using water proofing compound, finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. (NOTE: WPC to be measured and paid separately).

Applying a coat of cement slurry @ 3Kg/ Sqm including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

Applying one coat of primer conforming to IS: 3384-1986 over plastered surfaces @ 0.40 litres/Sqm of density 0.87-0.89kg/litres at 25°C and viscosity 70-160CPS (primer shall be of same make as of memebrane), complete all as specified and directed by Engr-in-Charge.

APP (Atactic Poly-propylene polymer) modified membranes, five layered, 3mm thick weighing not less than 3.5 kg/Sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacture's instructions by authorised applicator as per manufactureres instructions, complete all as specified and directed by Engr-in-Charge.

Dismantling water tanks of capacity exceeding 1000 litres & not exceeding 2000 litres complete all as specified and directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position of capacity 1000 ltrs including 15 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed with all fittings and fixtures, complete all as specified and as directed by Engr-in-Charge.

Vitreous chinaware squantting pan, ''Orrisa pattern'', size 580mm x 440mm white, with Cast iron 'P' or 'S' trap, front or back inlet, integral footrest excluding flushing cistern and flush type, etc and making good to floors (fixed in repair) complete all as specified and directed by Engr-in-Charge.

Urinal bowl of half stall pattern basin only including connections to flushing pipe and outgoing pipes (fixed in repair), complete all as specified and directed by Engr-in-Charge.

PVC valveless, syphonic action type flushing cistern, crystal white, 10 ltr capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32mm dia PVC long bend flush pipe 90cm long and 15mm dia 450 ling PVC Connection with CP brass coupling nuts and PVC washers at both ends (fixed in repair) complete all as specified and directed by Engr-in-Charge.

PVC(SWR) vent cowl 75mm bore complete all as specified and directed by Engr-in-Charge.

PVC (SWR) reducer (110 to 75mm)complete all as specified and directed by the Engr-in-Charge.

PVC (SWR) bend any radius 75mm bore complete all as specified and directed by Engr-in-Charge.

PVC (SWR) bend any radius 110mm bore complete all as specified and directed by Engr-in-Charge.

110 mm PVC (SWR) branch piecesdouble (doubleY) equal or unequal, complete all as specified and directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete, all as specified and directed by Engr-in-Charge.

Galvanized corrugated mild steel sheeting, 0.63 mm thick with two corrugations side lap, fixed with ' L' or 'J' hooks and washers, as in roof covering with grade of zinc coating 275, complete all as specified and directed by Engr-in-Charge.

All as per serialitem No. 58 here-in-above but fixing only.

PGI mild steel sheeting 0.63 mm thick, as in ridges, valley, gutter etc; fixed with L-type or J-type hooks and washers, complete all as specified and directed by Engr-in-Charge.

All as per serialitem No. 60 here-in-above but fixing only.

Dismantling wrought iron or mild steel work of any description not otherwise specified complete all as spcified and directed by Engr-in-Charge.

Mild steel work as in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

1st Class hard wood plain solid chowkats and frame, wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed by the Engineer-in-Charge.

30mm thick 2nd class soft wood glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) supplied and fitted to chowkhats complete, all as specified and as directed by the Engineer-in-Charge.

35mm thick,factory made, 2nd class hard wood ( Sal/Hallock) plain, framed, panelled shutter (two panels) with lock rail and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides. The size of rail and style as per IS-1003 (Part-I) Kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

75mm butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete, all as specified and directed by Engr-in-Charge.

200mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

100mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

75mm long aluminium handles, cast type, anodised, complete all as specified and directed by Engr-in-Charge.

Raised pointing to random or polygonal rubble uncoursed or brought upto courses in CM1:6 complete all as specified and directed by Engr-in-Charge.

Two coats of oil bound distemper on newly/old plastered surface of walls over a coat of JK primax and one coat of JK wall putty including preparation, complete all as specified and directed by the Engr-in-Charge.

Preparing surfaces of wood and wood based materials new or old, of any description and girth, not other wise described and treated with two coats of creosote oil complete all as specified and directed by Engr-in-Charge.

Dismantling of wall & ceiling boarding (fibre, pulp, insulation etc. or insulation board/salb/blanket any thicks with nails, including cover fillets and removing from site, complete all as specified and directed by the Engr-in-Charge.

Dismantling timber scantling framed work under 40 sqcm as in rails, purlins & rafters complete all as spcified and directed by Engr-in-Charge.

2nd soft wood(kail), wroyght, timber framed work as in repair of roof trusses, purlins etc; complete all as specified and directed by Engr-in-Charge.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc.0.50 sqm in each pane complete, all as specified and directed by Engr-in-Charge.

Dismantling Asbestos Cement sheets as in ceilling complete all as specified and directed by Engr-in-Charge.

False Ceiling using anodised aluminium section snap grid frame work of size 605x 605mm including hangers 6mm dia (upto 1200mm length) adjusting level to roof slab by means of ceiling cleats made out of GI flat 40x3mm size and 60mm long complete with 4mm thick asbestos fiber cement bldg board ISI marked e-board colour coated and designed complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, M-15, type B-1 (using 20mm graded crushed stone aggregate) as in coping, bed plates, bed blocks, lintels up to 1.5m clear span, bands etc. including necessary form work, complete all as specified and as directed by Engineer-in-Charge.

TMT bar 10 mm dia and over, cut of length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

All as per item No. 80 but 6 to 8 mm dia as in stirrups, complete all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden based surfaces of any description, area n.exc. 10 cm width or grith including prepration of surfaces, all as specified and as directed by Engr-in-Charge.

Two coats of synthetic enamel paint on old wood or wooden based surfaces of any description, exc.10cm width or girth including preparation of surfaces complete, all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc including removing material for taking credit ( credit shall be recovered as per credit Schedule attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including wooden box covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point/ fan/exhaust fan point/ bell point etc; controlled by one, one way switch, complete all as specified and as directed by the Engineer-in-Charge. Note : All the disturbed wall/ ceiling surface shall be make good to match the existing surface without any extra cost.

All as per item No. 86 above, but for one 3 pin socket outlet 05 Amp on the same board with other switches, complete, all as specified and directed by Engr-in-Charge.

All as per item No. 86 above, but for one 3 pin socket outlet 05 Amp on the independent board with other switches, complete, all as specified and directed by Engr-in-Charge.

Point wiring with 2.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 2.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including wooden box covered with 6 mm thick plastic laminated sheet ( Make Hylum) for one socket outlet on 15 Amps independent board/ one light point etc; controlled by one, one way switch, complete all as specified and as directed by the Engineer-in-Charge.

Socket outlet, 2 in 1, 3 Pin 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Socket outlet, 2 in 1, 3 Pin, 5/15 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Switch piano, flush type, single pole, one way,15Amp, complete all as specified and as directed by the Engineer-in-Charge.

Switch piano, flush button, 5 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Ceiling rose, surface type, 65 mm x 50 mm, two to three terminals/ PVC/ polycarbonate, isolated body fixed on PVC block, complete all as specified and as directed by the Engineer-in-Charge.

Supply & fix (in replacement ) of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar complete all specified and as directed by the Engineer-in-Charge. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing surface.

MCB SPN 40Amp, breaking capacity 10 KA, complete all as specified and directed by the Engineer-in-Charge.

MCB SPN 6-32 Amp, breaking capacity 10 KA complete all as specified and directed by the Engineer-in-Charge.

Universal batten for LED tube, suitable for indoor applications tube light fitting 1x18 Watt 4 FT, complete all as specified and as directed by the Engr-in-Charge. Make: Havell's Cat Part No REGALBATTENT5UPTO1X18WDSBSWH or equivalent in Philips/OSRAM/Bajaj.

LED tube light 18watt with very high efficacy suited for installation in existing batten all as specified and as directed by the Engr-in-Charage. Make: Havells CAT Part NO. CRYSTAL1213T8DSTL18WLED865SGLASS or equivalent in Philips/OSRAM/Bajaj.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40x40x6mm and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and shown in EP-3 of SSR Part-I & as directed by Engr-in-Charge.

1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular stranded conductor of size 10 Sqmm, 2 core, complete all specified and as directed by the Engineer-in-Charge.

House service bracket (hook type) complete with 3.0m long GI pipe 40mm dia, medium grade, two Nos 90 Degree bends M S hook etc, complete all specified and as directed by the Engineer-in-Charge.

Energy efficient LED integrated batten, suitable for indoor applications tube light fitting 1x10 Watt 2 FT complete, Trim LED NEO including all fixing arrangement complete, all as specified and as directed by the Engr-in-Charge.

1x25 watt LED security light fitting with lamp pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismatic polycarbonate cover with individual LED lenses with GI pipe 1.5 mtr length, clamps, nuts, bolts, complete, all as specified and as directed by the Engr-in-Charge.

Electric water heater, storage type, capacity 25 ltr, BEE 5 star rated complete all as specified and directed by Engr-in-Charge. Make: Jaquar Model Elena/Racold Model ALTRO 2/Venus Model: WAVE Note : Fixing of geyser on wall with suitable size anchore bolt with hammer drill and making good the disturbed surface including plaster work shall be part of job at no extra cost.

Iron tank cover made out of 2mm thick MS sheet of circular shape having dia 45cm inculding welding and fixing of sharp nails 15 Nos., length 2 inches for protection of monkeys and mangurs. Providing locking arrangements for both sides and border made of 25x2mm thick flat iron duly one coat of primer and one coat of black paint including screws, washers etc; including providing handle for both sides in suitable size for 500 and 1000 ltrs PVC water storage tanks completed all as specified and directed by Engr-in-Charge.

M/S DAYA SONS

M/s Thakur Engineers