Special repairs of officers single accn (Building No P-84, P-86, P-87 and P-88) at North camp of 274 Transit Camp, Khanpur under GE (South), Delhi Cantt-10

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed .

Dismantling wrought iron or mild steel of any description not otherwise provided for complete all as specified and as directed .

S&F for 0.63mm thick galvanised,corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranced hook bolts and washers, in roofs walls etc with grade of zinc coating 275 complete all as specified and as directed.

All as per Ser Item No 3 above but plain sheet as in ridge/flashing board of width or girth not less than 610mm.

S&F mild steel flat iron for wind tie etc including necessary drilling holes and fixing with necessary self drilling and self tapping screws/bolts and nuts, neoprene and limpet washers with 150mm end laps wherever required complete all as specified and directed.

Fixing only mild steel flat iron for wind tie etc including necessary drilling holes and fixing with necessary self drilling and self tapping screws/bolts and nuts, neoprene and limpet washers with 150mm end laps wherever required complete all as specified and directed. Note: Cost of new screws/bolts, nuts & washers is included in quoted rate.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed .

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n exc 1.5 sqm each complete all as specified and directed .

Taking down shutters of any description of exc 1.0 Sqm but not exc 2.0 Sqm each, complete all as specified and directed .

Taking down of shutters of any description of n.exc 1.0 Sqm each, complete all as specified and directed.

Taking down and refixing in same opening after any kind of alteration of shutters of any description of exc 1.0 Sqm but not exc 2.0 Sqm each, complete all as specified and directed .

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed .

Dismantling floor, wall hearth or tilling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc. 0.06 Sqm but n.exc. 0.11 Sqm in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and including screed bed 15mm thick in cement mortar 1:6 complete all as specified and directed.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161(1979) grade YST-240 complete all as specified and directed.

M&L for vitrified ceramic coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18sqm but not exceeding 0.36 sqm, in floors etc. set and jointed neat cement slurry and pointed in white or coloured cement to match the colour of tiles over & including 15mm screed bed in CM 1:6 complete all as specified and directed

Taking up or down steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed .

(a) 15mm bore

(b) 20mm bore

S&F Galvanised iron tubes medium grade with all fittings and fixed to walls & ceiling or laid in floors of following sizes complete all as specified and directed .

(a) 15mm bore.

(b) 20mm bore.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floor etc ) of following sizes complete all as specified and directed.

(a) 15mm bore.

(b) 20mm bore.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @3% by wt of cement on fair faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed. Note : Water proofing compound will be measured and paid separately.

Supply only integral water proofing compound.

S&F 35 mm thick flush shuttrer, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cost aluminium alloy, length of bolt 300 mm all as specified and directed.

S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21complete all as specified and directed.

S&F 75mm size MS butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F aluminium, anodised barrel tower bolt of extruded section 150mm size all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length of cover plate 140mm complete all as specified and directed..

S&F for aluminium (die cast) body door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed.

S&F in repairs steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed..

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and directed.

M & L for preparation of new or previously un treated steel and iron surfaces over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of new or previously un treated wooden surfaces over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

S&F for bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for size 15mm bore complete all as specified and directed..

S&F in repair Vitreous China wash basin, white, flat back, size630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F Hat and coat hooks, solid body, 175mm to 250 mm - Cast iron or mild steel complete all as specified and as directed.

S&F brass chromium plated tubular towel rail 20mm dia D type 60 cm long complete all as specified and as directed.

S&F Vitreous China soap tray embedded in the wall complete all as specified and as directed

S&F in repair European type WC (Pedestal pattern) complete including pedestal pan and trap including connection to drain, flushing pipe, seat cover (excluding flushing cistern) complete all as specified and directed

S&F in repair PVC 10 ltr flushing cistern valveless, syphonic action type, low level , white ,with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair CP fancy type pillar taps suitable for 15mm dia pipe, cast copper alloy, with capstan heads,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair CP fancy type stop valves suitable for 15mm dia pipe, cast copper alloy, screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs CP shower roses 125mm with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F in repair PVC Connections 15mm size 600mm long with PTMT nuts complete all as specified and directed.

S&F in repair Waste coupling 32mm bore for wash hand basin cast copper alloy complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 90cm long for WHB complete all as specified and directed.

S&F in repair Toilet paper holder of Vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F angle stop valve fancy type chromium plated with capstan head high pressure screwed for iron pipe and fixed, Bore dia of pipe 15mm complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and getting out in Soft / Loose soil for foundation etc or for shafts, wells, cesspits, manholes, pier holes, pipe and cable trenches etc not exceeding 10 Sqm on plan complete all as specified and as directed .

Demolition and breaking of 100 mm dia., drain pipes (Salt glazed ware, AC or reinforced concrete set in cement mortar complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100mmdia complete all as specified and directed..

M & L for cutting salt glazed stone ware drain pipe in position including jointing socket end of new pipe to same with packed spun yarn and sement mortar 1:1 for 100mm dia complete all as specified and directed.

M & L for salt glazed stone ware drain pipes laid in trenches and jointed for 100mm dia complete all as specified and directed.

Surface excavation in soft/loose soil n. exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed.

M&L for 150 mm thick broken stone hard core of gauge of n exc 63 mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rolled /rammed to a true surface complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in floors complete all as specified and directed.

Demolition of plain cement Concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Material and labour for 75 mm thick Cement concrete1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection finished cement concrete surfaces even and smooth without using extra cement all as specified and as directed.

M&L for providing, cement concrete 1:2:4 Type B1 (using 20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

S&F mild steel framed work Fe-290 (Gde E-165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, pulp, insulation etc) or insulation board/slabs/blankets any thickness including cover fillets complete all as specified and directed..

S&F 6mm thick asbestos cement plain building boards in ceiling, fixed in ceiling, flat or sloping to steel frame with screws complete all as specified and directed.

Fixing only for asbestos cement plain building boards in ceiling, fixed in ceiling, flat or sloping to steel frame with screws complete all as specified and directed.

M&L for preparation of new or previously untreated wood surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and as directed

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified and as directed

Material and labour for washing down and stopping of old distempered surfaces of ceiling and applying two coat of oil bound distemper complete all as specified and directed.

Material and labour for preparing new surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistent primier on plastered and other surfaces complete all as specified and directed.

Material and labour for washing down and stopping of old distempered surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed.

Material and labour for preparing new surfaces of walls and applying two coat of cement based paint over a coat of primer of same make complete all as specified and directed.

Material and labour for washing down and stopping of old painted surfaces of walls and applying two coat of cement based paint complete all as specified and directed.

Taking down carefully the old unserviceable Aluminium/ Copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as per the existing finish complete all as specified and directed.

M&L for point wiring with single core multi strand copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 Volts grade electrical cable on PVC casing caping with CI/pressed steel terminal boxes of required size factory made and factory painted with stove enameled black paint with top cover 3 mm thick plastic/laminated sheet (ISI Marked) of required color with screwed and cup washer with all accessories including 1.5 Sqmm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly for the folowing complete all as specified and directed.

(a) One light /fan point controlled by one way switch

(b) One 3 pin socket outlet 5 amps on independent board

(c) One 3 pin socket outlet 5 amps point on same board

(d) One 3 pin socket outlet, 15 amps on independent board but with cable 2.5 Sqmm for main and 2.5 sqmm as earth wire as power point.

S&F switch piano, flush type 5 Amps single pole one way complete all as specified and directed.

S&F socket flush type 5 Amps single pole one way complete all as specified and directed.

S&F switch piano, flush type 15 Amps single pole one way complete all as specified and directed.

S&F socket flush type 15 Amps single pole one way complete all as specified and directed.

S&F ceiling rose surface Bakelite 60x 25 mm two to three terminals complete all as specified and directed.

S&F ceiling fan regulator electronic type 240V AC complete all as specified and directed.

S&F Batten holder with PVC body and back plate suitable for LED Bulb B-22 cap complete all as specified and directed.

S & F LED RETROFIT Lamp of 9 watt for fixing in batten holder/wall mounting/ bulkhead point complete all as specified and directed.

S & F LED Integrated Batten T5, 20 Watt, 4 Ft White, indoor decorative aluminium extruded T5 LED battern integrated type complete with including fliexble wire in replacement of old unsv existing 36 Watt tube light fitting, complete all as specified and directed. Make: - Cat Part No LTTB4F20WLED/W of C&S or equivalent Make in Havells/Halonix/Philips/CG.

S & F LED Integrated Batten T5 LED tube light fitting of 10 Watt - 2' white, indoor decorative aluminium extruded T5 LED battern integrated type complete with including fliexble wire in replacement of old unsv existing 36 Watt tube light fitting complete all as specified and directed. Make: - Cat Part No : LTTB2F10WLED/W of C&S or equivlent Make in Havells/Halonix/Philips/CG.

S&F RUGBY Bulkhead suitable for LED 09 Watt of Base B22, Bulk head in die cast aluminium housing & frosted glass including all accessories connecting up twisted flexible copper conductor cable of suitable size of 230 V, 50 Hz complete all as specified and directed. Make : -Cat : LHKL01160099 of Havells or equivlent make in C&S/Halonix/CG/Phillips). Note : LED 09 Watt of B22 base shall be measured & paid saperately under respective item.

Taking down of Old ceiling fan and deposited to MES Store yard complete all as specified and directed .

S & F Ceiling Fan 1200 mm sweep (48" inch) copper wounded 5 star BEE rating complete with including fliexble wire all as specified and directed .

Taking down of old serviceable/unserviceable exhaust fan, dismantling blades, transportation to work shop and carrying out rewinding, transportation to site, reinstallation and testing complete all as specified and directed. Note : Rewinding will be measured and paid under respective item of this Schedule.

M&L for Rewinding of Exhaust fan 300 mm sweep by dismantling of exhaust fan motor cutting and removing of burnt windings, cleaning, winding with super enamelled copper wire of superior quality, same gauge of wire, same Nos of turns including provision of insulation paper applying of varnish drying of varnish and assembling of exhaust fan complete all as specified and directed.

Supply & Fixing sheet metal enclousure for DB's when MCB's to be used Single, pole and Neutral 12 way ,240 volts, double door bus bar neutral link,earth bar and din rail complete all as specified and directed.

Supply & Fixing MCB SPN 40 Amps 240 volts complete all as specified and directed.

Supply & Fixing MCB SP 6 to 40 Amps 240 volts complete all as specified and directed.

M&L in replacement of earthing complete with galvanised steel earth plate 600X600X6.3 mm thick buried directly in ground (earth pit not less than 2.25 M deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI earth lead wire 4.0 mm as earthing leads by means of bolts, nuts, check nuts and washers all joints as shown on drawings and including excavation, earth work. GI pipe light grade 15 mm bore for protection of GI earth wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt PCC (1:2:4) type B1chamber and MS angle iron frame of 40mmx40mm x3 mm and RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No 3 of SSR Part -I and conected to earth test point including testing complete all as secified and directed.

Taking down of old unserviceable MCB DB's any type complete all as specified and directed.

M & L for laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm x 2 core including taking out old cable all as specified and directed.

Returning filling, in including spreading ,leveling, watering and well ramming in layers not exc 25 cm each all as required complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed.

Supply and laying old size sub class ‘B’ bricks well burnt for cable protections laid flat with length equal to width of brick over cable perpendicular to length of cable complete all as specified and directed by Engr-in-Charge

Supply & laying galvanised steel tube (GI) Medium grade of size 40 mm bore with screwed socket joints together with all fittings such as bends, elbows, tees, short pieces connectors, caps, plugs and unions etc and fixed complete to walls and ceilings or laid in trenches all as specified and directed . Make :- Jindal/Surya/Prakash.

M/S.Parmod Johar

M/S Davinder Kumar

PARGATI TOWER CORPORATION