SPECIAL REPAIR OF E/M WORK AT BLDG NO P-149 OF HQ 475 ENGR BDE AND SPECIAL REPAIR OF BLDG NO T-134 AND T-135 OF SOUTHERN COMD CBRN SCHOOL LOCATED AT NASIRABAD

Amount

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc 15cm thickness (above or below GL) complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed by Engr-in-Charge.

Taking down cement or cement lime plaster or stone / brick wall, ceiling including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area exc 1.5 Sqm but n. exc 4.0 Sqm each complete with hold fasts etc complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area n.exc 1.5 Sqm each complete with hold fasts etc complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone masonary built in cement mortar etc complete all as specified and directed by Engr-in-Charge.

M&L brick work with fly ash modular bricks,straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for walling Random rubble masonary uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed by Engr-in-Charge.

All as per item No. 8.00 above here in before but except stone complete all as specified and directed by Engr-in-Charge.

Extra over stone masonary for hammer dressing to face beds and joints mixmum depression on face (sand stone) n. exc 20mm depression etc complete all as specified and directed by Engr-in-Charge.

M&L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of brick work / stone masonary surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:4) on other than fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. Note:- WPC measured and paid separately.

M&L for rough cast plaster mix with crusted stone (6-10mm), sand and cement in the ratio 1: 1.5: 1, over 15mm thick rendering in CM 1:4 on stone / brick masonary wall surfaces complete all as specified and directed by Engr-in-Charge.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed by Engr-in-Charge.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for vitrified ceramic tiles light shade10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for vitrified ceramic tiles light shade 10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 sqm, in vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed plaster 10mm thick in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

S&F Pressed steel door frame of size 105 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate,hold fasts etc. complete all as specified and directed by Engr-in-Charge. Note:- The rates include for filling PCC 1:3:6.

S&F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates incl necessary fixing lugs hinges, lock strike plate, hold fasts etc. complete all as specified and directed by Engr-in-Charge. Note:- The rates include for filling PCC 1:3:6.

S & F Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels commercial type on both side and both facesis covered with approved pattern with Decorative coloured laminate type 1 of 0.9 mm thick and all around side faces covered with 10mm thick 1st class hard wood liping duly polished complete all as specified and directed by Engr-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing using single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2020 complete all as specified and directed by Engr-in-Charge.

Taking down old u/s steel window / ventilator and S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including Two coat of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed by Engr-in-Charge. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick glass, ordinary quality, 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed by Engr-in-Charge.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-Charge.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

S & F in repairs 150 mm long door stopper of alumunium alloy body door stopper fixing on door, complete all as specified and directed by Engr-in-Charge.

S&F 300mm ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed by Engr-in-Charge.

S&F 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed by Engr-in-Charge.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed by Engr-in-Charge.

S&F 25mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed by Engr-in-Charge.

Refixing old 15mm GI tubing (Concealed type) galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed by Engr-in-Charge.

Refixing old 20mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed by Engr-in-Charge.

Dismantling of existing unserviceable RCC/PVC water tank and S&F 500 Litres capacity rotational moulded polythene water storage tanks(cylindrical vertical with closed top ) hoisted & fixed in position complete all as specified and directed by Engr-in-Charge.

S&F 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed complete all as specified and directed by Engr-in-Charge. (minimum weight 210 gms)

S&F in repairs 15mm bore cast copper alloy chromium plated fancy type bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F mild steel framed work such as grills, grating cooler stands, etc, with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

M&L providing 50x50mm aluminium anodised grills mesh for fixing in wooden gauged door shutter weight not less than 1.2Kg/ Sqm complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC (SWR) floor trap/ Nahani trap 75mm, plain with grating including jointing to waste pipe fixed in cement concrete type (1:2:4) complete all as specified and directed by Engr-in-Charge.

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 75mm thick as in plinth protection finished fair & even laid in alternative bays n. exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of 1mm thick wall putty, complete all as specified and directed by Engr-in-Charge.

M&L for newly plastered surfaces two coats of cement base paint over one coat of cement based primer on plastered/ concrete surfaces of walls including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M & L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engr-in-Charge. (Fe- 410W Grade-E-250 quality A).

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified and directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and making good to disturb surface, complete all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminum zinc coating GI based profiled steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ridge to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

M & L for cement concrete (Type B0, 1:2:4, 12.5 mm graded aggregate) in copings, kneelers, apex stones, bed plates, water troughts and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engr-in-Charge.

S & F in repair false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm,complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, complete all as specified and directed by Engr-in-Charge.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paidfor separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 5.5mm thick sheet glass ordinary quality and glazing in square, complete all as specified and directed by Engr-in-Charge.

S & F Mild steel Mortice lock, vertical type, 4 levers size 100 mm complete all as specified and directed by Engr-in-Charge.

S & F Door closer hydraulically regulated, designation No. 3, universal type, Aluminium extruded section body, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed by Engr-in-Charge.

Taking down existing tar felt or of any description including cement plaster or concrete of any thickness from the roof surfaces of building including cleaning the surfaces in all respect & preparing it for further treatment & removing rubbish from site complete all as specified and directed by Engr-in-Charge.

Material and labour for 40mm thick (avergae consolidated thickness) PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed by Engr-in-Charge.

M&L for rendering 10mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on fair faces of RCC/stone patti roof surfaces finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note:- WPC will be measured and paid separately.

M&L for cutting out cracks to 'V' section in existing roofs or terracing, cleaning out and filling solidly with hot mixture of bitumen and clean dry sand 1:1(by weight ) complete all as specified and directed by Engr-in-Charge.

M&L roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 mircron high molecular high density polyethylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 mircron HMHDPE film weight not less than 2.60 kg/ Sqm applied with bonding material using blown type bitumen primer Grade 85/25 @ 1.20 Kg/Sqm over bitumen primer conforming to IS -3384 @ 0.40 Kg /Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg /Sqm over APP membrane with all overlaps complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed by Engr-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment coloured, reflective type of approved quality and vibrated with mechanical vibrator complete all as specified and directed by Engr-in-Charge.

M&L for sand filling under floor in foundations inclding watering and consolidation complete all as specified and directed by Engr-in-Charge.

Providing cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) as in coping, Bed block for hold fasts including necessary formwork complete all as specified and directed by Engr-in-Charge.

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floor/path with grey cement and no pigment laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engr-in-Charge.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed by Engr-in-Charge.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc complete all as specified and directed by Engr-in-Charge.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor, complete all as specified and directed by Engr-in-Charge. Make: KEI/Havells/Benlo

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for, complete all as specified and directed by Engr-in-Charge.:- Makes for wire: KEI/Havells/Benlo Makes for conduit: Polycab / Kalinga / Kinjal

All as per item No 77.00 above but One light point/bell point controlled by one way 5 Amps SP switch complete all as specified and directed by Engr-in-Charge.

All as per item No 77.00 above but One ceiling fan/exhaust fan point controlled by one, one way switch complete all as specified and directed by Engr-in-Charge.

All as per item No 77.00 above but One 5 pin 5 Amps socket outlet on same board with other switch complete all as specified and directed by Engr-in-Charge.

All as per item No 77.00 above but One 5 Pin 5 Amps socket outlet on independent board with other switch complete all as specified and directed by Engr-in-Charge.

All as per item No 77.00 above but with 2.5 Sqmm cross sectional area electric cable for 15 Amp socket outlet on independent board, complete all as specified and directed by Engr-in-Charge.

S&F stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed by Engr-in-Charge.

S&F of switch piano 1 way 6/10 Amp, complete all as specified and directed by Engr-in-Charge.

S&F of switch piano 1 way 16 Amp, complete all as specified and directed by Engr-in-Charge.

S&F of socket 6 Amp, 2/3 pin combined complete all as specified and directed by Engr-in-Charge.

S&F of socket 6 Amp/16 Amp, 2/3 pin combined complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm, complete all as specified and directed by Engr-in-Charge.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed by Engr-in-Charge.

S&F box type LED tube light fitting in acrylic linear tube 1x 20 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube rod 20 watt, complete all as specified and directed by Engr-in-Charge. Make Bajaj , Havells, Benlo

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed by Engr-in-Charge. Make Bajaj , Havells, Benlo

Supply and fixing LED street light fitting 25/30/40 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp and street light bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed by Engr-in-Charge. Make Bajaj , Havells, Benlo

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm white light with white powder coated CRCA housing with LED driver, lumen efficacy >100 Lm/w complete all as specified and directed by Engr-in-Charge. Make Bajaj , Havells, Benlo

Supply and fixing in repair LED mirror light fitting, 10 watt, 590 mm length complete with all accessories pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge. Make Bajaj , Havells, Benlo

S&F exhaust fans AC single phase 230V of size 300mm sweep PVC body with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan including opening for exhaust fan and making good complete all as specified and directed by Engr-in-Charge. .

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy, complete all as specified and directed by Engr-in-Charge.

S&F wall fan of size 300 mm sweep, Speed upto 2100 RPM, Air Delivery 90 CMM, 230/240 volts including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed by Engr-in-Charge. Make:- Havells, Bajaj, Usha

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 12 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed by Engr-in-Charge.

S&F of MCB distribution board triple pole & neutral IP-43 double door metal, 4 way ,415 volt made out of CRCA sheet steel , factory made powder coated with insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed by Engr-in-Charge. Make: Legrand/ Schneider/ Seimens/ Benlo Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed by Engr-in-Charge. Make: Legrand/ Schneider/ Seimens/ Benlo Note: MCB DB and MCB SP/SPN will be of same make.

Supply and fixing of MCB TPN 63 Amp capacity,415 volt , 10 KA , 'C' curve complete all as specified and directed by Engr-in-Charge.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete all as specified and directed by Engr-in-Charge.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 16 sqmm, 4 core complete all as specified and directed by Engr-in-Charge. by Engineer-in-Charge.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 10 sqmm, 2 core complete all as specified and directed by Engr-in-Charge. by Engineer-in-Charge.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, complete all as specified and directed by Engr-in-Charge.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and directed by Engr-in-Charge.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed by Engr-in-Charge.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed by Engr-in-Charge. Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

S&F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Benlo(Bentec)

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Benlo(Bentec)

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge. Make: Havells/Legrand/Benlo(Bentec)

S&F of modular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge. Make: Havells /Legrand/ Benlo(Bentec)

Taking down existing exhaust fan & wall mounted fan and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired, complete all as specified and directed by Engr-in-Charge. Make Crompton/Havells/Philips

Supply and fixing wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic/glass body suitable for B22 Base in warm white or cold white complete all as specified and directed by Engr-in-Charge. by Engr-in-Charge. Make: Havells , Model- LHFOECE1TZ1B014, LHFHANDBTN1K007, LHFOAJE2TZ1I060 and LHFHANDBTN1M007 or equivalent model of Mepro/Philips

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp in warm white and cold white including connecting up with three core flexible copper conductor cable of suitable size complete. Make:- Crompton/Havells/Philips

Supply and fixing and testing energy saving street light luminaire 25 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed by Engr-in-Charge. Make Crompton/Havells/Philips

Supply and fixing surface mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed by Engr-in-Charge. Make Crompton/Havells/Philips

Supply and fixing recess mounted LED 12 watt Slim, compact, auminum die cast edge lit panel, round fixture with opal diffuser and separate electronic driver complete all as specified and directed by Engr-in-Charge. Make: Havells , Cat Part No LHEBHDP7IZ1W012, or equivalent model of Philips/Wipro

Supply and fixing surface mounted LED downlight 12 watt round shaped , Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed by Engr-in-Charge. Make Havells, Model -Trim Cosmo Surface Round, Cat Part No LHEAAHP7IL1W012, or equivalent model of Philips/Wipro

Supply and fixing surface mounted LED downlight 18 watt round shaped , Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed by Engr-in-Charge. Make Havells, Model -Trim Cosmo Surface Round, Cat Part NoLHEAAHP7IL1W018, or equivalent model of Philips/Wipro

Supply and fixing suspended LED light fittiing 36 watt in sleek design , lumain efficiency upto 100 Lm/W , incl LED driver and accessires for suspension complete all as specified and directed by Engr-in-Charge. Make- Crompton or equivalent model of Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed by Engr-in-Charge.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable. Make of wire- Finolex/KEI/Havells Make of PVC conduit - Polycab/ Finolex/Legrand-MDS Note : - Two run of single core cable, one run of earth continuity conductor and 1 mtr PVC conduit shall be measured as one unit length.

M& L for TV Socket incl PVC conduit and co axial cable wire complete all as specified and directed by Engr-in-Charge.

M& L for Telephone socket incl PVC conduit and telephone wire complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of concealed wiring wall and applying two coats of oil bound distemper all as over a coat of chalk white including 1mm average thick wall care putty or match as per existing complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new decorated surfaces of wall concealed wiring and applying two coats of weather coat paint match as per existing colour complete all as specified and directed by Engr-in-Charge.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed by Engr-in-Charge.

Taking down and refixing any size of PVC wall cladding hollow cored and a tongue and grooved edge fixed with screw including required PVC cleat at edges and a corner complete all as per directed by Engr-in-Charge.

Taking down and Supply and fixing of Change over Three Pole Neutral AC 63 to 100 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed by Engr-in-Charge. Make: Havells/ Crompton/ ABB or equivalent.

S&F LED 2 way ligh tfitting,6 watt, in cool day/warm white IP 65 Aluminium Die cast complete with all accessories pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge. Make:Wipro cat part no. WIPRO GARNET 6W 1X2 WAY WALL LIGHT (DW40627) or equivalent Crompton /Philips

S&F of vertical TPN distribution board , IP-43 double door metal, 4 way , made out of CRCA sheet steel , factory made powder coated with insulated vertical phase bus bars , shrouded neutral bars, earth bars, colour coded interconecting wire set , blanking plates suitable for up to 125 amp MCCB's as incomer and MCB's SP/TP as outgoing complete all as specified and directed by Engr-in-Charge. Make : Legrand/Schneider/Seimens Note: MCB DB, MCCB and MCB's will be of same make.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed by Engr-in-Charge. Make : Legrand/Schneider/Seimens Note: MCB DB, MCCB and MCB's will be of same make.

M&L of cutting holes by drilling machine or any equipment in stone walls built in cement mortar or in cement lime mortar for inserting or passed the wiring through beam or wall alongwith MS pipe suitable for inserting into the hole and making good as specified and directed by Engr-in-Charge. Note: No extra cost to be paid of drilling machine or equipment.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S & F of MCB SPN, 240 volt, 32 to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S&F of MCB TPN, 415 volt, 100 Amp capacity,10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge.

S&F in repairs MCCB, 100 Amp, 4 Pole, 25 KA, 415 V, thermal magnetic release type, Ics=100 % Icu, with adjustable overload setting and adjustable short circuit setting , including spreader terminals and phase barriers complete all as specified and directed by Engr-in-Charge. Make-Legrand / Siemens / Scneider / Havells

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) in wall, trench and under Kota stone/Tiles, 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed by Engr in Charge. Note: No extra cost will be paid against cutting of Kota stone or tiles.

Supply and fixing tubes light grade GI tubing 50mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection .

M/S SUMAN ENTERPRISES

Sree Ram Enterprises

M/s SUNIL ENTERPRISES