SPL REPAIR OF BLDG NO. P-50 AT MS VIHAR, P-119, PROVN OF LED SECURITY LIGHT AND PROVN OF SEPTIC TANK AT MIL STN AT GE(S) AKHNOOR.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates finishing concrete surface even and fair without using extra cement including necessary formwork, complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in plinth protection, joints filled with bitumen sand mixed 50mm thick, finished even and fair without using extra cement, complete all as specified and directed.

S&F non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and directed.

S&F non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile not exceeding 0.11 Sqm , in floors bath room etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and directed.

M & L for non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) suitable size to match existing floor tiles 7 to 8 mm mm thick, as in skirting set and jointed in neat cement slurry (3 Kg cement per Sqm) and pointed in white or coloured cement to match shade of tiles over 10 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work, complete all specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

M&L Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles over 10 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work ,complete all as specifed and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.after that appliying brushing neat cement slurry 3Kg /Sqm to receive Kota stone. complete all as specified and directed.

M&L for granite 20mm thick (table rubbed and polished) in cooking platform and like 12mm thick in cement mortar 1:4 including pointing in white cement (1:2) using marble dust making holes in RCC shelves suitable for gas pipe with round edges where required, complete all as specified and directed.

M&L for machine cut kota stone slab flooring 16-18 mm thick over 20 mm thick cement mortar 1:6 screed bed laid and jointing with grey cement slurry mixed with pigment including rubbing and mirror polishing complete with machine all as specified as on stair, shelves etc, including rounding of edges, complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 16-18 mm thick as in riser of step, skirting, dado and pillar laid over 10mm thick rendering with cement mortar 1:4 ,and jointing with grey cement slurry mixed with pigment including rubbing and mirror polishing complete with machine complete all as specified and as directed.

M&L for repairs to sunken floor/ slab with the following specifications:- (a) Demolition of PCC and taking out old brick bat filling and roughening surfaces of old concrete floor and wall by picking, sweeping clean and washing down with water to remove dust etc. (b) PCC 1:2:4,type B-0, using 12.5mm graded stone aggregate averaging 50mm thick as in sunken floor,with proper slope towards GI spout. The dia of GI Spuot pipe shall be 50mm medium grade. The minimum length of Spout shall be 500mm and if any spout comes above chajja than the length of the spout shall be more than Chajja projection. Ends of Spout shall be tippered and any cutting through brick/ RCC structure shall be done by the Contractor and rates are deemed to be included of this aspects. (c) providing 15mm thick cement plaster in cement mortar 1:3 mixed with water proofing compound @ 3% by weight of cement over bottom and vertical surfaces finishing the surface even and smooth without using extra cement. (d) Damp proof course on horizontal / Vertical surfaces with preparation & applying one coat of self priming (33% dilution) and two coats of undiluted material @ 10.67 lts per 10 sqm of Make : smart care Damp proof of M/s asian paint or equivelent for water proofing compound. (e) Graded Brick bats filling under sunken floor. (f) PCC 1:3:6,type C-1,using 20mm graded stone aggregate 75mm thick, over brick bats filling as in subbase to receive tiles.

M&L plain cement concrete 1:5:10 type E-2 using 40mm graded crushed stone aggregates as filling under floors (sunken slab), complete all as specified and as directed.

M&L Cutting holes into or through brick walls built in cement mortar and making good the surface in cement mortar 1:3 area not exc 150cm, complete all as specified and as directed.

S&F 32mm bore GI pipe bevelled cut at both ends by making hole in walls sunken portion approx above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surfaces complete etc., complete all as specified and as directed.

M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete 1:1.5:3 using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm including necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. (Note: welded mesh to be paid separately), complete all as specified and directed.

S&F for Hard drawn steel wire fabric cut to lengths, bent to shape required and trying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement, complete all as specified and as directed.

M&L Grubbing up bushes, tree trunk cutting of trunk portion nexc 10cm girth including cutting of tree/bushes grownin over wall and roofs digging out roofs and making good distance area of wall/roofs with PCC 1:3:6 type and using 20mm graded crushed stone aggregates, complete all as specified and directed.

S&F for tube 'medium grade' galvanized, with all fitting and fixed complete to walls and ceiling etc 15mm bore, including taking down or up steel tubing and connections and removal to store, complete all as specified and directed.

S&F for tube 'medium grade' galvanized, with all fitting and fixed complete to walls and ceiling etc 20mm bore, including taking down or up steel tubing and connections and removal to store, complete all as specified and directed.

Cutting chases in brick wall for concelled water tubing exc 10 cm but not exc 20 cm girth and making good, complete all as specified and directed.

S&F in repair bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore, complete all as specified and directed.

S&F in repair for basin mixer for mixing hot and cold water 2 in 1 fancy type brass chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed, complete all as specified and directed.

S&F in repair 15mm angular stop cock with wall flange stainless steel/brass chromium plated, screwed down high pressure with or without lathered hot and cold with long screwed shanks and fly nuts, complete all as specified and directed.

S&F in repair stop valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20mm bore pipe, complete all as specified and as directed.

S&F in repair PVC connection 15mm bore size with PTMT nuts of length 45cm length, complete all as specified and directed.

S&F in repair PVC valveless symphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including brackets 10 ltr capacity, complete all as specified and directed.

S&F in repair for fancy brass chromium plated shower rose 125 mm, complete all as specified and directed.

S&F in repair for stainless steel sink with draining board made of 1.00mm thick sheet for kitchen with plug, washer waste pipe cast iron cantilever bracket connecting union overall size 915mmx 460mm with bowl size 330mm x160mm., complete all as specified and directed.

S&F in repair CP grating ISI marked 150mm dia with centre hole, complete all as specified and directed.

S&F in repair for stainless steel plate rack of superior quality size 36" x 30" with not less than 8 kg, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) (White in colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. including float valve 20/25mm and taking down existing tank, complete all as specified and as directed.

S&F in repair vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but excluding lime concrete bedding, complete all as specified and as directed.

S&F in repair vitreous china wash basin, white, oval shape, flat back, size 550x400mm with full pedestal including 15mm bore CP Wash Basin mixer tap for mixing hot and cold water screwed down for iron pipe with waste coupling,waste pipe, cutting for and pinning in ends of brackets or erecting stand porcelain stopper a pair of CI brackets, complete all as specified and as directed.

S&F fixed in repair for Gun-metal, globe or gate valves, for bore dia of pipe 20mm with iron wheel head, screwed both ends for iron pipe and, complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia (D) type 60cm long between flanges, complete all as specified and directed.

S&F in repair waste pipe for SINK/WHB/Urinal for 32/40mm dia, complete all as specified & as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chowkhat or frame with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

M&L pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed .

M&L pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed.

M&L for plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregates as in foundation filling and mass concrete in foundation including necessary formwork, complete all as specified and as diected.

M&L for plain cement concrete M-10 (1:3:6), type C-0, (using 12.50mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates and in hold fasts or filling in hollow of steel frame, including necessary form work, complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded etc. with suitable PVC sheet beading including hinges etc, complete all as specified and directed.

S&F factory made, 35 mm thick plain framed panelled shutter (two panel) of second class hard wood rail and style with lock rail and panel of 9 mm BWP commercial ply.The size of rail and style as per IS:1003 Part I, klin seasoned and chemically pressure treated, complete all as specified and directed.

Supply and fixing of cupboard shutter 20mm thick (style) factory made pannel PVC including chowkat frame made out of M.S tubes 19 gauge for top and bottom rails M.S frame shall be covered with heated moulded plain colour PVC © channel having a PVC sheet strip of 10mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side 10mm (5mmx2) thick of 20mm and 20mm cross PVC sheet and as gap insert for top and bottom rail. Pannelling for plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing as in repairs 18/19 mm thick Prelaminated particle board, interior grade, Prelaminated one side decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work, complete all as specified and as directed.

S&F for external teak wood lipping, 6mm thick fixed with nails over block board or veneered particle board for cupboard self, complete all as specified and as directed.

S&F glazed and skelton shutters using 2nd class hard wood 35mm thick open rebated and prepare to receive glass or gauge etc edges of framing plain and chamfered or fitted cut or mitered beads for securing glass size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square, complete all as specified and as directed.

M&L for glazed ceramic tiles in vertical surface 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles over 10 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work, complete all specified and directed.

S&F factory made steel window, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet 4mm thick glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1517/15, sheet No- 1/3 to 3/3 and as directed . Note :- Cost of window shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately.

S&F factory made steel Ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet glass 4mm thick frosted glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1517/15, sheet No- 1/3 to 3/3 and as directed . Note :- Cost of ventilator shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately.

S&F glavanised Mild steel wire cloth. 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvnaised wire staples, complete all as specified and directed.

S&F butt hinge, ISI marked, medium weight cold rolled mild steel 100mm long to PVC Door etc, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt ISI marked of extruded section and fixed, length of bolt 200mm, complete all as specified and directed.

S&F extruded aluminum alloy handles 150mm ISI marked size fabricated type anodized, complete all as specified and as directed.

S&F mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, ISI marked, complete all as specified and as directed.

S&F Aluminum alloy, anodized sliding door bolt ISI marked with hasp staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolt of extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed.

S&F hasp and staple saftey type aluminium anodised with mild steel hinges pin including bolt to hing plate ISI marked and fixed with screw size 100mm, complete all as specified and directed.

M&L for preparation of new or previously untreated wood or wooden surfaces of any description, over 10 cement mortar in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cement mortar width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed .

S&F floor doors stopper of aluminium alloy body and tenque anodised ISI marked with hard drawn steel spring fixed in floor 150mm long, complete all as specified and directed.

S&F as in repair epoxy powder coated rods of mild steel 25 mm with fixing brackets, pelmet rods including pair of fancy type finnals, complete all as specified and directed.

M&L for Taking down existing old treatment including padding,water proofing plaster of any description any type, roof tiles, cement mortar screed bed and removing existing bitumen felt treatment including brushing, brooming, cleaning top surfaces of roof slab to recieve plaster etc including disposing off debris from MoD land, complete all as specified and directed. (i). Applying cement slurry over concrete surfaces @ 3Kg/Sqm (ii). Rendering 15mm thick in cement mortar 1:4 mixed with water proffing compound as per manfactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and evn including curing the plastered surfaces for 7 days by ponding of water over the roof (leveling course) (iii). Applying evenly one coat of cold bituminous primer conferming to IS 3384-1986 @ 0.40 Kg per Sqm on the cleaned plastered surfaces iv. Applying evenly one coat of blown hot bitumin of grade 85/25 @1.2Kg per Sqm primed surfaces (v). After the primed surface has dried, apply a coat of hot blown 85/25 penetration grade blown bitumen or equivalent viscosity grade blown bitumen (Penetration of bitumen when tested as per IS : 1203 will not be more than 40) conforming to IS 702 @ 1.20 Kg/Sqm of the surface.

item No 68 cont..... (vi). Prove App ( Atactic polyproplene ) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film. Minimum weight of membrane will be 3 Kg/Sqm. Other properties of APP modified water proofing membrane will be as laid down in MES SSR-I Part 11.42.2.2. APP membrane will be laid minimum end lap of 150 mm and side lap of 75 mm bonded with hot blown bitumen. (vii). Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen or equivalent viscosity grade blown bitumen ( Penetration of bitumen when tested as per IS 1203 will not be more than 40 ) conforming to IS 702 @ 1.20 Kg/Sqm and blinded with fine sand in dry condition @ 0.50 Kg/Sqm and applying two coats of aluminium paint over a coat of primer, complete all as specified and directed. Note:- Complete treatment shall be carried out by the applicator of the manufacturer only or through their authorised personal only.

Demolition brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and precast concrete articles, complete all specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in cement mortar 1:6, complete all as specified and directed.

M&L 5mm thick plastering on fair faces for concrete surfaces finished the surface even and smooth without using extra cement in cement mortar 1:3 on ceiling, complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or concrete surfaces finished the surface even and smooth without using extra cement in cement mortar 1:4, mixed with water proofing compound @ 3% by weight of cement, complete all as specified and directed. (Note: Cost of water proofing compound shall be included in item), complete all as specified and as directed.

M&L for preparation of new surfaces of wall and applying two coats of exterior emulsion (Apex paint), complete over one coat of primer, complete all as specified and as directed

M&L for preparation of new surface of wall with 3mm thick wall putty on plastered surface and applying two coat of oil emulsion white or coloured over a coat of primer of chalk whitening on walls, complete all as specified and as directed.

M&L for preparation of old surface of wall with 3mm thick wall putty on plastered surface and applying two coat of oil emulsion white or coloured over a coat of primer of chalk whitening on walls, complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over coat of primer, complete all as specified and as directed.

M&L for preparation of old/ decorated, un-decorated, plastered or unplastered surfaces of walls including complete removal of existing treatment, making surface even and filling weather proof putty in small holes, cavities, cracks and applying one coat of distemper oil emulsion over 1mm thick birla white wall care putty, complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coat of white wash over one coat of wall care putty of 3mm thick, complete all as specified and as directed.

M&L Preparation of old decorated un- decorated, plastered or unplasterted surfaces of walls including complete removal of existing treatment and applying one coat of exterior emulsion (Apex paint), complete all as specified and as directed

Dismantling of 100mm bore cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out from floors or walls complete, complete all as specified and directed.

Dismantling of 75mm bore cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out of trenches, if required, complete all as specified and directed.

S&F Cast iron sand cast soil, waste and vent pipe, 100mm bore, in any length with or without ears, with cement joints, fixed on walls, complete all as specified and directed.

S&F Cast iron sand cast soil, waste and vent pipe, 100mm bore, in any length with or without ears, with cement joints, in floors, complete all as specified and directed.

S&F Cast iron sand cast soil, waste and vent pipe, 75mm bore, in any length with or without ears, with cement joints, fixed on walls, complete all as specified and directed.

S&F Cast iron sand cast soil, waste and vent pipe, 75mm bore, in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and directed .

S&F in repair cast iron bend, 100mm bore pipe (any radius), with duck's foot or heel rest, complete all as specified and as directed .

S&F in repair cast iron branch piece, 100mm bore pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed .

S&F in repair cast iron branch piece, 75mm bore pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed .

S&F in repair cast iron bend, 100mm bore pipe (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed .

S&F in repair cast iron bend, 75mm bore pipe (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and as directed .

S&F in repair cast iron branch piece, 100mm bore pipe, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed.

S&F in repair cast iron ‘P’ or ‘S’ trap, with grating of 100mm outlet dia including jointing to waste pipe fixed in plain cement concrete, M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates), complete all as specified and as directed .

S&F cast iron floor trap of 75mm dia outlet, plain with grating including jointing with solvent cement, complete all as specified and as directed .

S&F in repair PVC (SWR) pipes, 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed .

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and as directed.

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches, complete all as specified and as directed.

S&F in repair PVC (SWR) bends of 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

S&F in repair PVC (SWR) bends of 75mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm dia junction double, (Double T) equal or unequal, complete all as specified and as directed.

S&F in repair PVC (SWR) 'S' trap of 110mm dia outlet, including jointing with solvent cement, complete all as specified and as directed.

S&F in repair PVC (SWR) branch piece110mm bore, double (double Y) equal or unequal, complete all as specified and directed.

S&F in repair 150 x 100 mm dia stoneware Gully trap setting and jointing with cement mortar 1:1, complete all as specified and directed .

M&L for pre-cast cement concrete 1:2:4 cover slab for manholes etc using 20mm graded stone aggregate, set in cement 1:4, complete and including necessary formwork all as specified and directed.

M&L for TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed.

S&F Mild steel bars 10mm dia and over TMT bars cut to length bent to shape reqd including cranking, bending spirally for hooping for columns hooking bends and binding with including mild steel wire (annealed) not-less than 0.9mm dia or securing with clips quality, complete all as specified and directed.

Surface excavation not exceeding 30 cm and averaging 15 cm deep and getting out in any type of soil, complete all as specified and as directed.

M&L for hardcore of broken stone, gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and as directed.

M&L for 100mm thick plain cement concrete 1:4:8 type D-2 ( using 40mm graded crushed stone aggregate ) as in sub base flooring including form work, complete all as specified and directed.

M&L for chequerred cement concrete tiles glossy finish coloured 20cmx20cmx25 mm thick pattern as approved by GE as in patches in floor set & jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over creed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6, complete all as specified and directed.

S&F in replacement of kitchen cabinet size ( Length and Height as per space) and width shall not be less than 450 mm, including partitions, shelves and drawers with brass sliding rails, door hanles, door catchers, over all cabinet internally and externally made with both side PVC laminated termite proof board, 18/19 mm thick, ISI marked including PVC kitchen/cup board frame of size 18mmx63mm made out of 18mm thick PVC pre-laminated ply coloured and frame shall be fixed with 50mm long steel screw inside using drilling machine and plastic fasteners, having following specifications: (i) Outer frame made size 50mmx47mm with same board. (ii) Shutters both side PVC laminated termite proof board, 18/19 mm thick having contineous piano brass hinges of 30mm flap width with one No brass handle of 75mm including brass door catcher of not less than 50mm size in each shutter. (iii) Drawers made of both side PVC laminated termite proof board, 18/19 mm thick including brass handles of front and two sliding rails at sides in each drawer. cont...

M&L for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for of water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding and taking down existing steel.complete all as specified and as directed

M&L for plain cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in hold fasts,copings, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork, complete all as specified and as directed.

S&F for Hard drawn steel wire fabric cut to lengths, bent to shape required and trying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement, complete all as specified and as directed.

Excavation in trenches in any type of soil not exceeding 1.5 m wide and not exc. 1.5 mtr deep ,complete all as specified and directed

Excavation in trenches in any type of soil exceeding 3.0 m wide and not exc. 3.0 mtr deep for poles and getting out , complete all as specified and directed

Returning filling including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in trenches, complete all as specified and directed.

Removal of surplus soil obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed.

M&L clean dry river sand in trenches/ducts for cushioning to cable, 8cm in depth before laying the cable and 15cm in depth after laying the cable, complete all as specified and directed

M&L for brick protection to cable using old size sub class 'B' bricks, laidflat, dry butt jointed, laid lengthwise perpendicular to the axis of cable, complete all as specified and directed.

Supply and fixing electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60 Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH including dismantling existing meter any type, complete all as specified and directed. Note: - Old electronic meter temper proof shall be deposited at store yard of MES and shall be property of department.

Taking down carefully copper/aluminium point wiring ( light, fan, bell, socket or power, light fitting ) complete,including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc, complete all as specified and directed.

Material and labour for point wiring (IN NEW CONCEALED CONDUITS TO SURFACES) complete with 1.5 Sqmm PVC insulated, FRLSH type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories are in concealed in walls /roofs/floors / ceiling etc. flush mounting MS box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.20mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular box,top cover, plate, blank plate,MS box,screws,washers and all modular electrical fixtures are to be used same make/brand only and modular box,top cover plate, MS box shall be measured and paid seperately under relevant items)

(a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch.

(b) One 3 pin 5 amps socket point controlled by one 6 amps switch on independent board .

(c) One 3 pin 5 amps socket point controlled by one 6 amps switch on same board .

(d) One light point controlled by two 2 way switches.

Description all as per item No.127 above, but point wiring with 2.5 Sqmm and earth conductor of size 2.5 Sqmm complete all as specified and directed but for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board, complete all as specified and directed.

Supply & fixing modular type switch 10 Amps, single pole,1way,1/2 module, 240V, ISI Marked, complete all as specified and directed.

S&F modular type switch 10 Amps, 2way, single pole,1/2 module, 240V, ISI Marked, complete all as specified and directed.

S&F Modular Bell push 6 Amp 1 module, complete all as specified and directed

S&F modular type socket type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked, complete all as specified and directed.

S&F modular type socket 6 A/16 Amps, 6 Pin socket 2/3 module with light indication, 240V, AC ISI Marked, complete all as specified and directed.

S&F modular type switch 16 Amps, single pole,1way,1/2 module, 240V, ISI Marked, complete all as specified and directed.

S&F fan regulator modular type electronic, stepped type(01 to 4/5), 100 to 120 Watts, 240Volts, AC, ISI marked, complete all as specified and directed.

S&F Bell, AC, 230 volts, single pole multi music type, complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/polycarbonate body ISI marked, complete all as specified and directed.

S&F angle lamp holder, polycarbonate insulated body with back plate including LED bulb 9 Watt, 240 Volts, complete all as specified and directe.

S&F in modular LED Indicator Lamp fixing on modular switch board 240V, AC, 50Hz suitable for 1/2 module ISI marked, including connecting with suitable length of 1.5Sqmm PVC insulated copper conductor, complete all as specified and directed.

S&F inverter based LED tube light fitting, 20 Watt, 4 feet long indoor decorative high lumen batten 230 volts, AC 50 Hz, 6500 K, Polycarbonate channel with lithium battery with back up time upto 4 hours and connecting up with twin core twisted flexible copper cable, complete all as specified and directed.

S&F LED light fitting 1x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F in LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed

S&F in decorative wall light fixture Globe type including 9 W LED Lamp made up of polycarbonate, complete all as specified and directed.

S&F in LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed

S&F in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

Supply and fixing ceiling fan, metalic, sweep 1200mm, with BLDC Motor, high speed, includuing modular electronic Regulator and necessary fitting/fixtures such as Hook and clamps etc including connectig wire of suitable size and length from ceiling rose to fan connector, Rated Air Delivery in CuM/ Min- 210 Minimum, Service Value CMM/W 7.85 Minimum No of Speed 5, Insulation Class- E, Temperature Rise including taking down of existing fan, complete all as specified and directed. Note: Old Ceiling fan taken out from the existing opening and shall be deposited at Store Yard of MES and shall be the property of Department.

S&F in repair for water heater storage type (Geyser) vertical/ Horizontal type as per site requirement with innder container of capacity 25 ltrs, electrically operated, AC 230 Volts, BEE 5 star rated, ISI marked including 04 Nos of old fashner nuts required suitable size fixed in brick wall, complete all as specified and directed. (i) The dismantled/unserviceable storage water heater shall be deposited with MES store yard for safe custody and shall be the property of the department.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete one single pole MCB 20/30 Amps, 240V complete concealed on wall and connecting with all connections complete including dismantling existing SPN MCB, complete all as specified and directed.

S&F GI bracket pipe of size 40 mm dia medium grade of 1.5 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc, complete all as specified and directed.

S&F LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed

S&F PVC insulated, PVC sheathed multistranded copper conductor cable of size 3 core 2.50 Sqmm with necessary electrical connections from connector block to with suitable 20 mm PVC rigid conduit heavy duty ISI marked including suitable size for clamps, complete all as specified and directed

Supply and laying LT UG cable, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area of size 16 Sq mm, 4 core laid in trenches or passing through pipes incl suitable lugs and accessories for making connections at both ends, complete all as specified and as directed

M&L for point wiring for one light point/fan point/bell point controlled by one-one way switch with 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including PVC casing caping medium grade of 25mm width complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making good the diturbed surfaces to match with the existing, compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of casing capping measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth).

(a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch.

(b) One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

(c) One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

Description all as per item No.159 above, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed but for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board complete all as specified and directed by Engr in Charge.

S&F Switch flush type, 5 amps 240 volts single pole on way, complete all as specified and directed.Supply and fixing switch piano, flush type, single pole, one way, 6 Amps, complete all as specified and as directed by Engineer-In-Charge.

S&F socket outlet, flush type 2/3-pin, 6-Amps, complete all as specified and as directed.

Supply and fixing switch socket combination,2 in 1 ,3-pin, 5/16-Amps, flush type, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing including connection testing of stepped type (multi-steps) electronic regulator for ceiling fan 1200/1400 mm, 240 volts, including connecting, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting, complete all as specified and directed.

S&F in repair for Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 for security light fitting luminare with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting, complete all as specified and directed.

Supply and fixing sheet metal enclosure DB TPN 4 way double door made powder coated out of CRCA mild steel sheet 200 amps rated bus bar dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to disturbed surface complete including dismantling existing DB, complete all as specified and directed.

S&F sheet metal enclosures DB's double door factory made power coated out ofr CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in walls and making good to disturbed surface and colour matching complete including dismantling existing DBs, complete all as specified and directed.

S&F MCB SP 6 to 32 Amps 10 KA,"C" series, AC, 240Volts, 50Hz , ISI marked, complete all as specified and directed.

S&F MCB SPN 32 Amps 10 KA,"C" series, AC, 240Volts, 50Hz, ISI marked, complete all as specified and directed.

S&F MCB TPN 63 Amps 10 KA,"C" series, AC, 415Volts, 50Hz, ISI marked, complete all as specified and directed.

M & L for sub main wiring in repair complete with 2 run of 6.0Sqmm single core copper conductor (ISI marked)cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including cutting chases and making good the surface, one run of 6 Sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and including taking down existing, complete all as specified and directed by Engr in Charge Note : - Two run of 6 Sqmm single core copper conductor cable and one run of 6 Sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only, complete all as specified and as directed.

M & L for sub main wiring in repair complete with 2 run of 4.0Sqmm single core copper conductor (ISI marked)cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including cutting chases and making good the surface, one run of 4 Sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and including taking down existing, complete all as specified and directed Note: - Two run of 4 Sqmm single core copper conductor cable and one run of 6 Sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only, complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, plain cement concrete earth pit chamber 1:3:6 type C1, of size 45X 45X 45 cement mortar, RCC cover 1:2:4 type B1 of size 45X45X6 cement mortar, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old unserviceable earthing item, complete all as specified and directed.

S&F in repair GI bracket pipe of size 40 mm dia medium grade of 1.5 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc, including taking down, complete all as specified and directed.

Supply and laying, connecting and testing for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 25 Sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc including taking down exixting cable any type and size all as specified and directed. (Excavation and earth work, sand cushioning, brick protection & GI pipe shall be measured and paid for separately), complete all as specified and as directed.

M&L for GI pipe 40 mm dia light grade fixing to wall or laying in floors for protection of cable complete existing pipe, complete all as specified and directed.

M&L in repair for GI pipe 40 mm dia light grade fixing to wall or laying in floors for protection of cable complete existing pipe, complete all as specified and directed.

S&F steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31 (9 metres long) with necessary excavation, foundation and coping including applying two coats of exterior weather proof paint of approved colour to pole and to MS cross arms, cable protection pipe, brackets etc with two coats of Aluminium Paint over a coat of red oxide primer including synthetic enamel painting in alternate lines of yellow/white & black strips min of 6 NOS (each strip 200 mm wide) at bottom of pole, complete all as specified and directed. Note: - Earthwork, cement concrete etc. will be measured and paid under appropriate items.

M&L for plain cement concrete M-10 (1:3:6), type C-1, (using 20mm graded crushed stone aggregate), nominal mix, as in stay , including necessary form work, complete all as specified and as directed.

Supply and Fix junction box water proof out door type made out of SMC sintex make of external dimensions 220x300x190mm single door type hinged with locking arrangements front operated with one number MCB 20 Amps capacity for housing single phase and neutral bus bar, including connecting the incoming/out going cables including cable glands SMC coated clamp bolts and fixed to the pole with mild steel flat of size 25x4mm, complete all as specified and directed. NOTE: Sintex or equivalent.

M&L for extra forming fair finished drain or channel 30 CM inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified and as directed. Note: Inner girth shall be measured.

M&L for plain cement concrete 1:3:6, type C-2, using 40 mm graded crushed stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm bore SGSW pipe, complete all as specified and directed.

Construction of soakage well of size 2.40 m dia and 4.5 m in depth, below inlet pipe level (Depth from Pipe to Ground Level 45CM), excavation in any type of soil including plain cement concrete M-10,1:3:6, type C-2 (using 40mm graded crushed stone aggregates) in foundation and honeycombed brick masonry in cement mortar 1:4 and reinforced cement concrete cover slab, M-25, (Design Mix) (using 20mm graded crushed stone aggregates), complete all as specified and as shown in drawing. Drawing No- CE/TD/1202/03 sheet 1/2 and 2/2 dated 09.10.03 revised 14.10.14 and 11.05.07.

Construction of Septic tank for 100 USERS (BRICK CONSTRUCTION) single chamber, including inlet and outlet chamber with top of slab in RCC M-25 (Design Mix) (using 20mm graded crushed stone aggregates) at ground level inclduing necessary earth work in any type of soil, PCC,RCC Work, Fowm work vent pipes and manhole cover, all items required to complete the job etc all as shown in HQ CEUZ TD Drawing No- CE/TD/1202/03 sheet 1/2 and 2/2 dated 09.10.03 revised 14.10.14 and 11.05.07 complete all as specified and as directed by Engineer-in-Charge. Note : All scope of work as shown in drawing shall be covered under quoted unit rate and nothing extra shall be admissible on whatsoever ground.

M&L for cutting to road for crossing sewage line and repair with plain cement concrete 1:3:6, type C-2, using 40 mm graded crushed stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm bore SGSW pipe at the level to existing road surfaces, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 150mm dia bore reinforced concrete pipes, class NP3, laid and jointed, complete with collars, complete all as specified and directed.

Please Enable Macros to View BoQ information