Laying Fitting of Parallel Mains in Place of Worn Out Supply Mains, Sub Mains at Balhama, Retrofitting of Existing Pipe Network at Mir Gund Aparpora (Under JJM)

Amount

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 2.9.1 All kinds of soil

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge (i) All KInds of Soil.

Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work. i.15 mm and 20 mm dia. G.I. pipes

ii.25 mm and 32 mm dia. G.I. pipes

Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe).

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket. i.80 mm dia

Providing, fixing of M.S flanges by welding including cost of cutting making both holes made out of 10/14mm thick M.S plate to the pipes of different dia’s and including cost of nuts, bolts, washers etc. (Complete Job). i. 150mm dia

i. 100mm dia

ii. 80mm dia.

iii. 65mm dia

vi. 50/40mm dia

P/F of Sluice valves / Gate Valve of approved make and manufacture like VAG, ZOLOTO, KIRLOSKAR incl. carriage to actual site of work, water testing of joints, commissioning of all interconnections , complete job. i. 100mm dia

i. 80mm dia

ii. 65/50mm dia

iii. 40mm dia

Providing, fixing of M.S fittings viz bends of suitable degrees / size to be fabricated out of 8mm to 10mm thick MS. plate as per the requirement of site. This item includes cost of lead, spun yarn, R.I. cloth and lead caulking, lead beating with insertion of spun yarn etc. The fittings should be leak proof and should be painted with Anticorrosive Red Oxide Primer and incld. all carriages, leads lifts, etc. complete.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. i. Welded

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. i. 50 to 80 mm nominal bore

ii. 25 to 40 mm nominal bore

Providing Installation testing & commissioning of Air valve including dismantalling of damaged air valve & returning of same to divisional store. This also includes welding / pipe specials needed to successfully commissioning of Air Valve(Double lobed) i. 50mm dia

ii. 25mm dia

Providing and laying handpacked stone soling (Quarry) 75mm nimonal size including ramming and dressing including all leads lifts and all carriage complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: i. 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level including curing, excluding the cost of centring, shuttering, and finishing. i. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level. i. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. i. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in: i. Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): i. Second class kail wood

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete i. Ridges plain (500 - 600mm)

Providing and fixing plained eaves boarding. 2nd class kail wood. 1. 250x32 mm (nominal size )

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws i. Budloo/fir wood.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. i. Second class Kail wood (35mm thick).

Centering and shuttering including strutting, propping etc. and removal of form for: i. Foundations, footings, bases of columns etc. for mass concrete.

i. Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

ii. Suspended floors, roofs, landings, balconies and access platforms.

12mm Cement plaster of mix: i. 1 : 4 ( 1 cement : 4 coarse sand)

Finishing walls with 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. 13.94.1 New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. i. Two or more coats on new work.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. i. Fixed to steel windows by welding

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. i. M.S. tube

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete i. On steel work

Providing & Fixing of Sign Boards at Tube Well Site & SR Site on 4mm Thick MS board (2'-6" Ht with Structural Steel 50x50x6mm Fixed above Gate 12'-0" wide) painted after priming coat with name of Schemes complete Job.

Fixing of chain link fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. This item also includes carriage of chain link fencing from Divisional Store upto site of work.

Fixing charges of MS lids of different size for Sluice Chambers etc. including concreting, angle irons, locking arrangements, hinges etc. required for the completion of job. This item also includes carriage of lids from Divisional Store upto site of work.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven storey height made with 40 mm dia M.S. tube 1.5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffoldings for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges (heavy weight) with Stainless Steel screws etc. complete. i. 75x50x2.50 mm

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : i. 250x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete i. 100x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete i. 100 mm

Carriage of material from various sources upto road site of work by mechanical transport. i. Pipe, Cement and Steel for an avg. lead of 10Kms.

ii Sand for an avg. lead of 15Kms.

iii Aggregate 20mm nominal size for an avg. lead of 5Kms.

iv Aggregate 40mm nominal bore for an avg. lead of 5Kms.

v Bricks for an avg. lead of 25Kms.

M/S FAROOQ AHMED BHAT

ZAHID AHMAD MAGRAY