CONSTRUCTION OF 4 LANNING FROM HISAR RAIPUR ROAD (SECTION KENCHI CHOWK TO SECTOR 1 and 4) RD 0 TO 0.680 IN HISAR DISTT. (PDG. STREET LIGHT ONLY).

Amount

Wires and Cables: Supply and erection of PVC copper insulated and sheathed 2-core circular flexible wire. (HSR 31.9) (d)Size 1.50 sqmm ( 48 / 0.20mm).

Moulded case Circuit breakers: Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. HSR 31.12 (c) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. Miniature circuit breakers of 9 KA breaking capacity. i) SP MCB 6 amp. to 32 amp.

v) TPN MCB 6 amp. to 32 amp.

Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. (HSR 31.21) xiii) Galvanized iron pipe 50 mm dia on flushed.

(Q) Earthing (HSR 31.22): i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required .

ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

xix) Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. staples of same size.

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections. (HSR 31.26) xxvii) 50 Sq. mm 3.5 Core Ard. Cable.

xl) 16 Sq. mm 4 Core Ard. Cable.

Supply and erection of suitable compression type brass cable glands for underground Cable. (HSR 31.28) ii) 10 Sqmm to 16 Sqmm Cable 2 to 4 Core .

iii) 25 Sqmm to 50 Sqmm Cable 2 to 4 Core

Pedestal: Supply and erection of Godrej Almirah type M.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embedded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- (HSR 31.33). i) M.S.pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embedded in cement concrete block of size 750 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 900 mm x 600 mm x 250 mm below ground level.

Supply and errection of double walled corrugated (DWC) HDPE pipe laid 1 meter below ground level including diging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of the labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work. (HSR 31.67) i) HDPE pipe 63/50 mm outer dia/ inner dia

ii) HDPE pipe 90/75 mm outer dia / inner dia

Supply and errection of Hot Dip Galavanized octagonal pole 3 thichness, with base plate including of nut and bolts and all accessories as supplied by the manufacture including cost of fundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galanized pole complet of 2 nos. 100 A, 4 pole nature links including connection etc with suitable connection arrangments for 2 no. MCB/ kit kat including cost of RCC 1:1:5:3 for foundation of size 0.7 m x 0.7m x 1.8 m with minimum 8 Nos. 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm CC for fixing the pole with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work. Make:- Vipin ST Poles/ Skipper/ Philips/ Bajaj/ Volmont. (HSR 31.68 ) iii) 9 M long pole with top dia 70 mm and bottom dia 155 mm with base plate of size 260 x 260 x 16 mm.

Non schedule items: Const. of R.C.C Foundation for 9 Mtr. (9000 mm) Decorative Poles (Cast Iron) 1:1.5:3 for foundation, size 0.8M x 0.8M x 1.40M with minimum of 8 nos 12 mm dia longitudinal MS reinforcement rods with rings of 8mm dia not more than 200mm C.C for fixing the pole with SF 20 mm dia 36" Long hot dip galvanized L type 4 Nos. Anchor bolts with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer in Charge of work.(On HSR Based)

Non schedule items: Supply/ errection/ testing / commissioning of timelight distribution board 65 amp 3 pole / 230 Volts with digital time switch having suitable size of 1 no. 63 amp TPN MCB, 1 no. 65 amp contactor, 1 HRC fuse , 1 No. Rotray Switch, 1 No. 16 amp fuse base, 1 No. Timer switch and 1 Indicator having IP 52/56 Degree protection all items should be of same make / manufacturer including padestal, including making connection and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-inCharge of the work. (Make:- IndoAsian/ Havell's).

Non schedule items: S/E of 120 W LED street light fitting < 110 Lumens per Watt Philips / Havell's / Bajaj/ Wipro make in pressure die cast aluminum housing with High Power LED lighting source with toughened glass top cover top opening seperate driver compartment with IP-66 protection and impect resistence of IK07 with 10 KA built in surge protection device device internal 5 KV and external 10 KV including all petty material with labour for errection, complete in all respect of Engineer-in-Charge of the work.

Non schedule items: Supply/ Erection/ Testing/ commissioning of Hot Dip Galvanized Double arms decerative type Hot Dip Galvanized made of Made out of 48.3mm O.D., MS pipe 1500mm long as per Cat No.VSPB014 of Vipin Make suitable for for 7/9 Mtr. Octagonal poles. Bracket complete with all hardware material like Nut-Bolt, Decorative Balls -1 Nos. & Dome - 1No. Hot Dip Galvanized after fabrication top covered with ornamental cap duly welded, painted 2 coats of aluminium paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-incharge of the work.

Non schedule items: Charges of boaring 2.5 mtr. below the gound level treanchless horizental with laying of PLB pipe by HDD machine (for laying the cable) including all labour and material required to complete the job in al respect upto entire satisfaction of Engineer- in- charge.

Non schedule items: Supply and erection of Double door sheet, steel superline/ Powerline/ Loadline TPN Vertical distribution boards suitable for TP/ FP veritcal MCCBs 25 KA MCCB upto 125 amp as incomer (but without cost of MCCBs) fitted with busbars, Neutral links,& Blanking plates complete with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. (i) 4 Way Vertical.

Non schedule items: Remove the existing foundation & 9 M pole with brackets and streeet light fittng the help of crane including the all petty material & labour for erection, complete in all respect of up to the entire satisfaction of the Engineer-in-Charge of the work.

Non schedule items: D/D of old Dismantled cost of single arm bracket for 9 M Long GI Octagonal pole

pawan Kumar

Chopta Offset Printers

Baliyan Electrical Works

The Bawani Khera Sach Co Op Multi Purpose Society Ltd Bawani Khera

The Sirsa Bansivat Coop L and C Society Limited