SPL REPAIR OF PANCHWATI GUEST HOUSE UNDER GE NEW DELHI, DELHI CANTT-10

Amount

Taking down old existing any type of water proofing treatment from the top of RCC/ arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified & directed.

M/L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3.

M&L providing cement concrete as in roof kerbs, levelling courses for making proper gradient/slope or mud stops rounded or chamfered on edges with B-1 , 1:2:4 using stone aggregate mixed with water proofing compound as per manufacture instruction including necessary form work complete all as specified & directed. (water proofing compound to be measured separately).

M&L for 10 mm thick ready mix plaster mixed with WPC @ 27ml/sqm including finishing the surface even and smooth without using extra cement for laying water proofing treatment, complete all as specified and directed.

M&L for surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC/plaster surface shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges complete all as specified and directed.

Contd item No . ... .. .5 Note: Grouting will be done when and where ever required. Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concreteNote: Will be done when and where ever required Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt. Make of water proofing treatment Dr Fixit Roof seal 148 or Asian Paint smart care damp proof or SIKA 710/715

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner. Makes- JOHNSON, ROCOTILES, THERMATECK

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

Taking up or down 20 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

Taking up or down 40/50 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, check nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

S&F of 20 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, check nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

S&F of 40 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, check nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturved surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 fittings on walls / ceiling or laying in floors including cement solvent and all fitting complete all as specified.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 40cm including making good of disturved surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

S & F 20 mm dia Brass Elbow

S & F 20 mm dia Brass Elbow (3/4 x 1/2)

S & F 20 mm dia Brass Tee

S & F Male Brass Threaded Adaptor (MTA/ MBTA) ) 20 mm dia

S & F Female Brass Threaded Adaptor (FTA/ FBTA) 20 mm dia

S & F CPVC BALL VALVE of dia 20 mm

S&F in repair gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed for 20mm dia pipe (ISI Marked)

S&F in repair gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed for 40mm dia pipe (ISI Marked)

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F 110 mm dia PVC (SWR) soil pipe, waste and rain water pipe single socketed in any length with rubber ring jointed, laid in floor or fixed to wall with clamps incl testing, setting and jointing with solvent up to six story bldg with necessary seafty precaution in narrow shaft complete all as specified and directed.

S&F 75 mm dia PVC (SWR) soil pipe, waste and rain water pipe single socketed in any length with rubber ring jointed, laid in floor or fixed to wall with clamps incl testing, setting and jointing with solvent up to six story bldg with necessary seafty precaution in narrow shaft complete all as specified and directed.

S & F 110 mm PVC (SWR) bends any radius

S & F 110 mm PVC (SWR) junction single, (Single T) equal or unequal

S & F 110 mm PVC (SWR) Cowl

S&F 110 mm PVC (SWR) any trap

S & F 75 mm PVC (SWR) bends any radius

S & F 75 mm PVC (SWR) junction single, (Single T) equal or unequal

S & F 75 mm PVC (SWR) Cowl

S&F 150mm PTMT Symet Bath assest Grating square hole/without hole fixed in position over Rain Water Pipe/nahani trap with cement slurry Make Prayag,

S&F MS Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to FE-290 Gde-E-165

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement as required to facilliate demolition complete all as specified and directed.

S&F rotational moulded polythene water storage tanks in double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 2000 ltrs incl making connection with fitting for inlet & outlet pipe.

S&F 40 mm bore ball brass valve, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

M&L framed work such as grills, gratings, water tank cage etc with ends of bars shouldered and/or riveted, welded or forged into spikes framed guard bars, barred doors & walk ways railings and similar work up to six story bldg including necessary seafty precaution confirming to Fe-290 Gde -E-165 complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each but with shutters (without taking off the shutter from the frame) all as specified.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m (without taking off shutters from the frame) all as specified.

S&F factory made uPVC any colour fixed glazed ventilator made of ( small series) frame 47 x 50mm mullion 47 x 68mm both having wall thickness of 1.9 + 0.20mm iwith one openable for PVC Exhaust Fan and single glazing bead of appropriate dimension ( Area upto 0.75 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

Supply and fixing factory made uPVC white colour openable window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 1.0 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Outer side fixed with SS wire mesh with 'U' channel properly fixing. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item).

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item).

M&L for providing & fixing ceiling at all heights with GRG ( glass fibre reinforced gypsum) false ceiling tiles of size 595 X 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 85%, NRC 0.50 to 0.75 as per IS 6225 1987. Noncombustible as per BS 476 (part 4) -1970and light reflectance of 85% (minimum) to be laid in true horizontal level supended of inter-locking metal T-grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 gms per sqm including both sides) comprising of main-T runner of size 15x32 mm of length 3000 mm, cross-T of size 15X32 mm of length 1200 mm and secondary intermediate cross-T of size 15X32 mm of length 600mm to form grid module of size 600X600 mm suspended from ceiling using galvanised mild steel items (galvanised @ 80 grm per sqm) i.e. 50mm lomg, 8mm outer diameter M-6 dash fasteners 6 mm dia fully threaded hanger rod up to 1000 mm length amd L-shape level adjuster of size 85X25X2 mm. Galvanised iron perimeter wall angles of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall wood screws. the work shall be carried out as per specification, drawing and as per directions of the engg-in-charge. with fully perforated 10 mm thick square edged GRG false ceiling tiles.

Taking down cement plaster at any position from brick or concrete surface incl racking out joints hacking for key and scrubbing down with water complete including removal of rubbish off the premises all as specified.

M&L for premix/readymix plaster 15mm thick on brick or concrete surfaces of walls, chajja, balconies,beams , columns, manholes etc and similar work finished even & smooth including necessary scaffolding, form work, safety precuation up to multi storey of bldgs complete all as specified & directed.

M&L for premix/readymix plaster 5mm thick on brick or concrete surfaces of walls, chajja, balconies,beams , columns, manholes etc and similar work finished even & smooth including necessary scaffolding, form work, safety precuation up to multi storey of bldgs complete all as specified & directed.

M&L washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 marble powder : 2 marble chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the marble chippings complete all as specified including complete removing existing grit plaster. (Payment for providing grooves shall be made seperately). (Note :- Only steel scaffolding is allowed and rate included in above item. The work shall be carried out by enclosing affected area by green cloth) up to G+3 storey building and deploy skilled labourers to execute the work)

M&L forming groove of uniform size 15 mm wide and 15 mm deep in top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under laying including removal of wooden battens, repair to the edges of panels and finishing the grooves all round as per approved pattern. The groove shall be finished with two coats of bitumenous paint complete all as specified and directed.

S&F Kitchen cabinets made out of PVC sheet board 19mm thick including dismantling of existing cabinets, making drawers, partitions, shelves and PVC board on all sides consisiting the following as directed by Engineer-in-charge:- (a) 19mm thick PVC solid flush board with 5mm thick pre-laminated sheet fixed on one side, as kitchen cabinet. (b) PVC Frame of size 50mmx47mm. (c) PVC Shutters having piano hinges and brass handle 75mm long No for each shutter. (d) Bottom back and sides of cabinet covered with 19mm thick PVC board with 5mm thick pre-laminated sheet fixed on one side. (e) Drawers having brass handle 75mm long and two long sliding rails for each drawers with magnatic catcher as required. (f) Cabinet must have one drawers supported of sliding rails. (g) Size of each cabinet shall not be exceeding 0.9 M x 0.75 M and 0.60 M depth. (h) Measurement will be considered only for front face i.e. length & height & depth 0.50m. (j) SS Jalli racks mounted on drawer chanel Note: Measurement for purpose of payment shall be made on external visible face for width x height (considering frame).

“S&F Modular Cabinet Kitchen accessories of Stainless Steel grade-304,4mm size rod thickness including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed by Engr in charge

Dismantling wrought iron or mild steel work of any description and any position not otherwise provided for complete all as specified and directed.

Material & Labour for providing and fixing stainles steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor, Staircase or the side of waist slab with suitable arrangement and make good of dismantled portion after fixing of SS railings complete all as specified and directed.

S&F toughened glass of any shape and size of 12mm thickness as in hinged doors, partitions, automatic doors and similar work including cutting to shape and embossing logo stamp as directed by GE, drilling holes required.

M&L Preparation of new plastered or un-plastered surface of wall/ceiling and applying two coats of Plastic emulsion paint with roller finish on any position over a coat of primer including preparation of surfaces with the application of multy layer of cement base wall care putty upto smooth fininshing complete all as specified and directed.

M&L for complete removal of existing treatment by mechanical grinder from old surfaces of ceiling/wall and applying two coats of Plastic emulsion paint with roller finish on any position over a coat of primer including preparation of surfaces with the application of multy layer of cement base wall care putty upto smooth fininshing complete all as specified and directed.

M&L for preparation of new plastered ceiling surfaces and applying two coats of distemper oil emulssion, white or tinted over one coat of primer including 3mm thick wall care putty complete all as specified & directed.

M&L for complete removal of existing treatment from ceiling surfaces and applying two of distemper oil emulssion, white or tinted over a coat of primer paint including 3mm thick wall care putty complete all as specified & directed.

Dismantling floor, hearth or wall tiling including CM bedding / terrazzo finish & removing serviceble tiles to store rubbish off the premises out of MOD land

M&L for double charged / ultra charged/Dark Shade vitrified tiles 10 mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm but n exc 1.00 sqm , in floors etc set and jointed to over and including 15mm thick screed bed in CM 1:6 and pointed in white or coloured cement to match over & including tucking of existing floors complete all as specified and directed.

Ditto all as per item No-67 but for in vertical surfaces as skirting, dado etc. and including 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F non skid ceramic tiles of approved colour and design 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed..

Ditto all as item No-69 but for in vertical surfaces as skirting, dado etc. and including 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for Glazed ceramic tiles of approved colour and design in vertical surfaces 600x1200x10mm thick including provision of high lighter tiles/boarder and jointed in neat cement slury and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:4.

M&L for circular cutting or notching and waste on any tiles

M&L for stone finish wall tiles design/shed shall be approved by GE in vertical surfaces 600x1200x10mm thick and jointed in neat cement slury and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:4.

M&L for decorative fabric vertical blinds/ louvers with complete fitting and fixtures channel or rail are made from high quality fabrics with strips or louvers hang from the head rail and linked by chain at the bottom. Vertical blinds have two control. one allows the blind louvers to be tilted to the left or right and block the light out let it in or filter it by tilting the louvers to an angle and other one lets louvers to an angle and other one lets louvers fully black by pull either to the left, right or centre. all blinds come with hand rail with match to all component with complete accessories all as specified and directed, includiung taking down of existing any type of curtain rod. complete fitting measured and paid in Sqm based on an open area covered by blinds.

M&L for reinforced cement concrete 1:2:4 type A-1 using 20 mm graded aggregate (nominal mix ) in slabs supported on walls, beams and columns in floor, roofs, conopies, chajja and in shelves and the like.

M&L for Form work to sides and soffits of floor or roof beams, cantilevers, shelves, chajjas incl supports, overhang for rough finished flat surfaces.

M&L for laying Micro-concrete cement based pre packed single component, chloride free, sulphate free,non shrink, free flow, self compacting, ready to use after mixing water in specified proportion of approved quality. The unit rate shall include the cost of form work for providing micro concrete patch repair as required at site with steel jack system and steel props to support the form work in this application of high strength, dual shrinkage, compensated, micro concrete for placing in nominal thickness of 50 mm to 150 mm for concrete repair.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required,including cranking, bending, spirally for hooping for columns, hooking ends and binding with with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed by Engr-in-Charge.

M&L TMT bars 6 to 8mm dia and over, cut to length, bent to shape required,including cranking, bending, spirally for hooping for columns, hooking ends and binding with with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed by Engr-in-Charge.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, drains, culverts and walls etc but excluding ashlar facings, dressed stone work and pre cast concrete articles, built in cement mortar including removing the unserviceable material out side the MOD land complete all as specified & directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of Exterior Emulsion paint (APEX ULTIMA) over a coat of primer all as specified and directed.

M&L for Y/L shape angle posts ,struts and similar works as in fencing including cutting tops to slope as directed , drilling holes , notching for wire etc, including all necessary drilling bolting or revited and similarly work confirming to Fe-290 all as specified and directed.

S&F in repairs Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as directed (each line wire to be measured)

M&L for preparation of new or previously untreated surfaces, of steel and iron work of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of Red oxide all as specified and as directed.

M&L cleaning sunken portion of slab (Bottom & sides) and providing water proofing treatment as under :- (a) Providing min 3" concave coving with PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate admixed with WPC conplast WL . Cement slurry admixed with bonding compound Nitobond AR to be used for bonding of coving with RCC member. Covering CI pipes with PCC 1:2:4 type B-0 using 20mm graded stone aggregate admixed with integral WPC conplast WL (Fosroc Chemicals India Ltd). (b) Drilling 50mm deep holes at a distance of 1m c/c and cleaned with water and air, fixing nozzles of 12mm dia on drilled holes, injecting non shrink cement slurry at a pressure of 40 psi and nipples plugged with quick setting compounds. (c) Applying 2 full coats of brush bond acrylic emulsion based elastromeric water proofing coating after the primer with a min time gap of 4-6 hrs between 1st & 2nd coat. (d) Applying 15mm thick plaster in CM 1:4 admixed with WPC conplast WL after ponding test for a period for 72 hours of sunken floor . (e)GI tubing 40 mm dia of mrdium grade for spout of 150 Cm long for each sunken floor. Note :- Plastered surface area shall only be measured for the purpose of payment.

M&L for lean concrete 1:5:10 type E2 using brick bats as in sunken floor concrete complete all as specified and directed.

S&F in repair Square 150x150mm 304-Grade Floor trap with Collar, Hinge or without hige top openable with Cockroach Trap all as specefied and directed

Supply and fixing of Table Top Basin of Size: 565x425x140 mm including cuplink and west pipe with stainless steel bottle trap of 32mm size with 250mm & 190mm long flexible tube & wall hook with NRV (Back blow preventer) including taking down old WHB (Model ALD-769L250x190 or equivalent)

S&F in repair Single Lever Basin Mixer Wall Mounted including Exposed Part Kit of Consisting of Operating Lever, Cartridge Sleeve, Wall Flange, Nipple & Spout and all fittings including long body tab (spout) including taking down old unservicable existing all as specefied and directed.

S&F 5mm thick modern mirror with border design suitable for wash basin cabinet with fitted with LED Front and Backlight, Stepless Dimmable Wall Mirrors with Anti-Fog, Shatter-Proof, Memory, 3 Colors, Double LED Vanity Mirror with touch off/on switch in one mirror including all fixing arrangement all as specefied and directed

S&F Bib Cock with Wall Flange including taking out old existing all as specefied and directed Make Jagaur Model : ORP-10037PM or equivalent make as approved by GE.

S&F in repair Angular Stop Cock with Wall Flange all as specefied and directed Make : Jaguar model ORP-10053PM or equivalent make as approved by GE.

S&F in repair Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 15mm Long Bend Pipe, Connecting Legs & Wall Flange including all fittings all as specefied and directed (Make : Jaguar model SOL-6281 orequivalent make as approved by GE.

S&F in repair Alive Maze Overhead Shower 200X300mm Round Edge & Rectangular Head Single Flow (Body & Face Plate Stainless Steel) with Rubit Cleaning System including arms and flanges and all connected items as specefied and directed. (Make : Jaguar model OHS-85859M1 or equivalent make as approved by GE.

S&F in repair Alive Maze Hand Shower 68X100mm Round Edge & Rectangular Head Single Flow (Face Plate Stainless Steel & ABS Body) with Rubit Cleaning System alonwith 1.2 mtr length coated pipe and all fittings all as specefied and directed (Make : Jaguar model HSH-855371 or equivalent make as approved by GE.)

S&F in repair towel rail of Make Jaguar Model : ACN-1101S or equivalent Grab bar 300mm Long, Stainless Steel all as specified

S&F in repair Soap Dispenser with Metallic Bottle Make Jaguar Model : ACN-1137N or equivalent make as approved by GE.

S&F in repair 1/4 inch Stainless Steel Brass Jet Spray for Toilet Sheet, Pipe Size: length 1 Meter,

S&F in repeair compact one-piece Ove toilet integrates the tank and bowl into a seamless design for your bathroom. Providing an efficient 10 L for flush and 3 L for half flush, this toilet is designed with a standard 305mm rough-in with S-trap accessories provided. Comfort height feature offers chair-height seating that makes sitting. down and standing up easier including all fittings such as seat cover, bend etc all as specefied and directed

S&F in repair Paper Holder with Flap Recessed Type (Stainless Steel) all as specefied and directed Make : Jaguar model AHS-1553 or equivalent

S&F 150mm size butt hinges stainless steel of 304 grade complete all as specified and directed.

S&F handle of stainless steel of 304 grade size 200mm size long etc. complete all as specified and directed.

S&F handle of stainless steel of 304 grade size 100mm size long etc. complete all as specified and directed.

S&F 200 mm long barrel tower bolt stainless steel bolt complete all as specified and directed.

S&F 100 mm long barrel tower bolt stainless steel bolt complete all as specified and directed.

S&F Matilic Pin to lock body - 45 mm, for bathroom, balcony door of thickness ranging from 28 mm to 55 mm including Set of 2 pieces of handles, 1 pcs computer lock body, 1 covering/receptacle plate along with screws for fittings.

S&F brass magic eye for panelled/flush shutter 35mm thick complete all as specified and directed.

M&L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, wall lining, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and and including rendering 20 mm thick in cement mortar 1:6 finished even and rough complete all as specified.

S&F 200 mm SS sliding door bolts including all fittngs in SS as approved by GE

S&F 75mm SS Hasp and staple including all fittngs in SS as approved by GE

S & F 2 nd class wood beading fixed in position with nail area exc 3 Sq cm but n exc 6 Sqcm lain fillets, square, rectangular or traingular in section, clean sawn, secured with nails or brads, including taking down

S&F in repair 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination incl teak wood liping 6mm thick on sides complete all as specified and directed.

Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fittings such as ceiling rose, pendent holders, regulators and socket point etc and making good the disturbed surface & wall/ floor complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for the following :

One light/fan/exhaust fan point controlled by one no, one way 6 Amp switch.

One light point controlled by two no, two way 6 Amp switch.

One bell/buzzer point controlled by one bell push complete all as specified and directed.

One three pin 6 Amp socket outlet point controlled by one no, one way switch on same board

One three pin 6 Amp socket outlet point controlled by one no, one way switch on independent board

All as per item No. 115 here in before but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board.Make:-RR/Polycab/Havells

Note for item No 115 & 116:- (i) Cutting chassing for concealed conduit and making good in cement mortar is deemed included in unit rate.

S&F in replacement of modular Switch 6 amps,one module, 230 vots, single pole, one way (ISI marked) complete all as specified and directed

S&F in replacement of modular Switch 6 amps,one module, 230 vots, single pole, two way (ISI marked) complete all as specified and directed

S&F in replacement modular bell push 6 amps one module complete

S&F in replacement 16 Amp rating modular switch one way one module complete

S&F in replacement of modular socket out let 230 volts grade (as catered in point wiring above) of following ratings:-

6 Amp - 2/3 pin combined 2 module complete

16 Amp - 2/3 pin combined 2 module complete

S&F in replacement of electric bell AC 230 Volt complete all as specified and directed .

S&F in replacement of ceiling rose 3 terminal / PVC / Polycarbonate, insulated body all as specified.

S&F of PVC plastic MCB protected socket 20 Amps with MCB SP upto 16 Amps 230 volts AC and plug top 16 Amps all as specified and directed by Engr-In-Charge.

S&F in replacement of PVC plastic MCB protected socket 20 Amps with MCB SP upto 16 Amps 230 volts AC and plug top 16 Amps all as specified and directed by Engr-In-Charge.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 4 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 4 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 4 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 4 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

M&L in replacement of submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 6 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

S&F in replacement of factory made sheet steel distribution boards, double door, SPN 12 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing all as specified.

Supply and fixing in replacement of MCB, 240V 10KA, B curve of following poles and current carrying capacity in the MCB DB complete with connection testing. :-

MCB SP 6 to 32 Amps

MCB SP 40 Amps

MCB SPN 32 Amps

M & L for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 meter deep below ground level) with the top edge of earth plate at a depth not less than 1.5 meter below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and including GI strip 25x4 mm up to 7.50 RM bolted (with GI nuts, bolts & check nuts) and riveted to earth (Plate) electrode at one end and connected to main switch board / test point (including test point) at the other and watering GI pipe (medium grade) 20 mm bore from bottom of earth pit to top of electrode and 40 mm GI pipe light grade for earth strip protection complete with earth pit in PCC 1:2:4 type B0 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh etc including necessary excavation and earth work in any type of soil, returning filling in and removal of surplus soil all as specified.

S&F in replacement of LED Tube Lightfitting of 20 Watt 230Volt(size 4 ft) complete with LED Tube Light 20 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified.

S&F in replacement of LED Tube Light fitting of 10 Watt 230Volt(size 2 ft) complete with LED Tube Light 10 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified.

Supply and fixing LED luminaire 600 mm x 600 mm, (2X2) 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F in replacement of LED Bulkhead fitting of 10 Watt 230 Volt , complete with LED Light 10 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified & directed.

S&F in replacement of 09 Watt Wall mounted decorative LED light fitting complete with 09 wall LED bulb all as specified and as directed

S&F in replacement of aesthetically designed ceiling/surface circular shaped decorative green perform sleek LED downlighter of 15 W fixture with opal diffuser to give glare free light including suitable LED lamp complete all as specified and as directed.Model :-DN296B LED20S-6500 PSU WW of Philips or equivalent model in Crompton/Havells.

S&F of aesthetically designed Roseate Table lamp LED light of 20 W,50HZ fixture with opal diffuser to give glare free light including suitable LED lamp having Lamp base E27 complete all as specified and as directed.Model-58139 of Philips or equivalent model in CG/Havells.

S&F of aesthetically designed Roseate Wall Light Single LED wall light of 20 W,50HZ fixture with opal diffuser to give glare free light including suitable LED having Lamp base E27 complete all as specified and as directed.Model-58135 of Philips or equivalent model in CG/Havells.

S&F in replacement of aesthetically designed muziris decorative warm white LED pictur light of 07 W CCT-3000K fixture with bronze finish for superior feel including suitable LED lamp of 07 W having LED Lamp base complete all as specified and as directed.Model-31402 of Philips or equivalent model in CG/Havells.

S&F 10 watt K type up down LED wall light with aluminium IP -65 protection grade, water proof body,CCT-3000K complete all as specified and directed by Engr-In-Charge.

S&F of Building security/ street light fitting 25 watt to be fitted at the pheripheral surfaces of the building including GI bracket of suitable size,fixing with clamp and other connected accessories complete all as specified and as directedCrompton/Philips/Havells.

S&F in replacement of decorative LED type post top lanterns luminaire 40 watts, outdoor type for 360 degree indirect light with resistant to corrosion, glare free having better uniformity with suitable driver complete with required size/length pipe for fixing the fitting and coping of the pipe for fixing the pipe in ground all as specified and as directed.

Supply & fixing of remote control Ceiling fan complete with blades,down rods and all connected accessories operating at 230 V with 1200/1400 mm sweep. Minimum air delivery should be 210 CFM,rated 5 star with brushless direct curent (BLDC) motor,color as per site requirement.Making arrangement for hanging fans to ceiling with proper hook,nut,bolt with twin core twisted flexible copper conductor complete all as specified and directed by Engineer-In-Charge in replacement of old unserviceable/burnout 1200/1400 mm sweep ceiling fans. Note:-The old U/S 1200/1400mm sweep ceiling fan to be deposited to MES store yard in safe custody.

S& F plastic body fresh air fan size 230 mm sweep with new plastic body fresh air/exhaust fan fan 230mm AC single phase 230 V 50 HZ with blades,frame ,louvers and other connected accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size and making arrngement to fix the exhaust fan with proper nut bolt all as specified and directed.

S& F metallic body exhaust fan heavy duty of size 450 mm sweep with new metallic body exhaust fan 450mm AC single phase 230 V 50 HZ with blades,frame and other connected accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size and making arrngement to fix the exhaust fan with proper nut bolt all as specified and directed in replacement of old U/S exhaust fan of 450 mm sweep size Note:-The old U/S exhaust fan 450mm sweep deposited to MES store yard in safe custody.

S&F of factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way VTPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete all as specified.

S&F in replacement of factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way VTPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete all as specified.

S&F of MCCB 4 pole 63 Amp, 415 Volts ,16kA fixed type including thimbles, nuts, bolts ,washers etc. and connections all as specified and directed

S&F in replacement of MCCB 4 pole 63 Amp, 415 Volts ,16kA fixed type including thimbles, nuts, bolts ,washers etc. and connections all as specified and directed

Supply and fix in replacement of hot water storage electric water heater, steel body with copper inner tank and heating element upto 2.0 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc. Note:-The old U/S geyser 25 Ltr deposited to MES store yard in safe custody.

S & F wall mounted electric chimney of minimum width 60 cm,with baffle filter,having suction power not less than 1350cum/Hr, with stainless steel outer layer,with 3 speed motorwith decorative smart cooker hoodSS/Glass, energyefficient LED light with digital display including ducting,having auto clean function,noise level not more than 60dB,control panel- touch & motion sensor control,including ducting as per site requirement all as specified and directed by Engr-In-Charge. Make:- Elica, Model kitty plus or equivalent of kaf/Hindware. Note:- The rate quoted by the contarctor will include ducting length required from chimney to the exhaust hole.

Material and labour for taking down of exhaust fan 300/450mm,sealing cable end,dismantling blades and removing fan and blades to store Note:-The old serviciable/U/S exhaust fan300/ 450mm sweep deposited to MES store yard in safe custody.

S&F rigid non metallic PVC conduit medium grade 20mm dia for telephone cable complete with all fixting accessories all as specified.

S & F of TV socket AC 220 Volt cat5/6 complete all as specified and directed .

Supply & Laying of 50 sqmm X 3.5 core XLPE LT cable 1100 volts grade heavy duty with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC Tape armoured with galvanized steel strip or wire and over all PVC Sheathed stranded conductor conforming to IS-7098 (Part-I) with latest amendments laid in tranches/fixed to wall/pole/laid in floor including necessary connections and suitable size of thimbling complete all as specified and as directed by Engineer-in-Charge of following size .

4.0 sqmm 2.0 core

10 sqmm 4.0 core

S&F LED bollard luminaire 10 watts, inverted pyramid tripod type with soft 360 degree light out door type having resistant to corrosion with better optics for uniform distribution complete with suitable driver & fixing nuts, bolts & washers all as specified. Cat pt No LBLSN-10CDL of Crompton Greaves or equivalent in Philips/Havells

Supply and fixing of 5 star rating split type AC 1.0 TR capacity complete with cooling coil, blower with motor, PCB and remote complete, compresoor, condensing coil, condensor fan motor suitable to existing model and make iron grill, and flair nuts for connection of Copper pipe with fixing plate suitable to existing model and make AC all as specified and directed.

Supplying, installation, testing and commissioning of LT panel 3.15 mm thick cubical outdoor type weather proof, totally enclosed with IP 65 protection made out of CRCA sheet angle iron of size 50 mm x 50 mm x 6 mm suitable for 3 phase, 4 wire ,440 volts, 50 Hz including cable glands, phase indicators, internal wiring,CT of suitable Ratio, voltmeter, ammeter, air passing holes with proper spacing to accommodate to all control switches and other accessories, cable connections with suitable size of lugs/thimble etc and locking arrangement with two locks godown type welded inside of the shutter with duplicate keys, spray painting with two coats of light gray paint over a coat of red oxide primer and mounted on two No bricks pillars including excavation and earth work complete PCC (1:2:4) brick work (1:4) and plastering complete:-

INCOMING

(a) MCCB 4 Pole 160 Amp,adjustable setting type, 415 volts 25 KA =01No

(c) Aluminium bus bar 250 Amps with insulator-04 Nos

(f) CT ratio of suitable size-01 set (set of three)

(g) Indication lamp – one set(set of three)

OUTGOING

(i) MCCB 100 Amps, adjustable setting type,3 pole,415 volts 25 KA - 03 Nos

Note : Unit rate quoted by the contractor here-in-before also includes for installation of panel on suitable PCC foundation and PCC plat form incl necessary earth and PCC work all as per manufacturer instructions and as directed by the Engr-in-Charge.

BEHAL TRADERS (BID ID -3092023)

M/S MSD & Associate (BID ID -3092282)

M/s SAAR ENGINEERS (BID ID -3092410)

M/S Rohit Enterprises (BID ID -3092460)

M/S Parmod Johar (BID ID -3082817)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3091990)

JYOTI ENTERPRISES (BID ID -3092414)