CONSTRUCTION OF 01 X TRG DIVISION INCLUDING SYNDICATE ROOMS WITH PARKING AT DSSC WELLINGTON

Lumpsum price worked out by the tenderer for BUILDINGS AND STRUCTURES as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for LAND DEVELOPMENT as listed in Schedule ‘A’ Part-IV

Lumpsum price worked out by the tenderer for ROAD, PATH AND CULVERT as listed in Schedule ‘A’ Part-V

Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI

Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VII

Lumpsum price worked out by the tenderer for PROTECTIVE WORKS as listed in Schedule ‘A’ Part-VIII

Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-IX

Lumpsum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-X

Lumpsum price worked out by the tenderer for COOLING APPLICANCES as listed in Schedule ‘A’ Part-XI

Lumpsum price worked out by the tenderer for DG SET as listed in Schedule ‘A’ Part-XII

Lumpsum price worked out by the tenderer for UPS as listed in Schedule ‘A’ Part-XIII

Lumpsum price worked out by the tenderer for EQUIPMENT EARTHING as listed in Schedule ‘A’ Part-XIV

Lumpsum price worked out by the tenderer for DEMOLITION/ DISMANTLING as listed in Schedule ‘A’ Part-XV

SCHEDULE 'A' PART XVI (MISCELLANEOUS ITEMS) Note: This schedule is not pre-priced by MES

DEMOLITION/ DISMANTLING

Taking down aluminium door/ partition incl glass/particle board etc exe. 1.5 sqm but not exe. 4 sqm all as specified and directed.

Old unserviceble Submain Wiring Cable any size/type, Conduit with accessories including terminal boxes any type with all accessories.

Taking Down LED light fitting any type and size

Taking Down DB/ MCCB of any type/ size

Taking Down MCB of any type/ size

Taking Down Exhaust fan any type (PVC and metal) and Capacity

INTERNAL ELECTRIC SUPPLY

(B) Diesel Engine: - Adequate capacity Diesel engine suitable for 58.50 KVA coupled drive independently above alternator and after considering derating as per site conditions after generating and reducing power consumed by accessories, directly coupled through flexible coupling, multi cylinder multi stroke direct injection, cold starting 1500 RPM, as per relevant ISI/BS - 5514 with an overload capacity of 10% for one hour in 12 hours continuous running complete with standard accessories all as specified and required for safe handling and operation salient features of accessories shall be as under Make :- KIRLOSKAR/CUMMINS / CATERPILLAR (GEMCO)/ Greeves

All as desccribed in Sl item No. 23 herein before but One Ceiling/Exhaust fan point controlled by one modular switch 6A

All as desccribed in Sl item No. 23 herein before but One 3 pin socket out let 6 Amps on independent board

All as desccribed in Sl item No. 23 herein before but One 3 pin socket out let 6 A on same board

All as desccribed in Sl item No. 23 herein before but One light point controlled by two 2 - way modular switch 6 A

M&L for Point wiring complete all a specified with 1100 Volts grade 4 sq mm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS 694 1990 with ISI marked (for phase, neutral and earth)in and including stove enamelled Steel conduit ISI Mark of minimum size 20mm dia all accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed galvanised steel pressed terminal boxes for fixing modular sockets of suitable size modules and the earth wire to be connected to common earty dolly all as specified and as directed.all as specified and as directed for One three pin modular switch socket 16 amps outlet on independent board

S&F slim surface mounted round 12 W light fitting LED panel aluminium die cast body with premium diffuser to ensure glare free &even distribution of light 12W, 220V,AC, 6000 K LED light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

S&F MCB DB VTPN 8 way having degree of protection as per IP 43 with metal door (double door) 415 Volts complete with 200 Amps rated copper bus bar with neutral link with provision for 4P MCB as incomer and MCBs as outgoing incoming specified and as directed.

S&F MCCB 4P 100 Amps MCCB 4 Pole, 415 V, Adjustable type, with breaking capacity 25 KA complete all as specified and as directed

SEWAGE DISPOSAL

M&L for 150mm bore DWC HDPE SN-8 pipes conforming to IS 14930 Part-2 / IS 16025 Part-24 with all fittings, laid in trenches, cut to required length and jointed complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

S & F hot press moulded SMC junction / terminal box of size with internal dimensions of 200 x 180 x 105 mm with hinged door, incl provision of 4 way connector 415 Volts made out of polycarbonate or Bakelite and 1 No MCB of 6 Amps with DIN bar, drilling holes for cable connections, connecting incoming and or out going cables by providing suitable of size of cable lugs/glands, fixed on pole by means of clamps made out of MS flat iron of size 25 mm x 4 mm all as specified

M/L for LT cable route indicator, cast Iron, Oval Shaped, size 200x150x6 mm with engraving "LT MES CABLE" embedded with PCC 1:3:6 Type C1 incl necessary excavation, returning filling & removal of soil complete all as specified and as directed.

M & L earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth strip 32 x 6mm dia, by means of nuts, bolts, check nuts and washer etc. of galvanised iron and earth lead protected by provision of GI pipe medium grade 40mm bore from earth electrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed.

Material and labour for street light bracket made of 40mm GI pipe light grade 1.5 m length bent in shape for mounting street light on one end, fixing the bracket on pole with suitable GI clamps, Nus and bolts all as specified and as directed..

Material and labour for providing coarse riddled earth of approved quality in trenches including filling, spreading and punning down to desired thickness as in cushioning to UG Cable complete and all as specified and directed by Engr-in-Charge.

COOLING APPLAINCES

Supplying, installing, testing and commissioning of Voltage stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of +/- 2.5% and of capacity 5KVA.

(DG SET )

Supplying, installing, testing and commissioning of 125 KVA/ 100KW capacity Silent Diesel engine Generating Set (The capacity of Generator set shall be net after all due derating factors as per relevant lSI standard), 415 volts, 3 phase, 0.8 Power factor, 50 Hz, 4 wire system as per IS 10001/10002 comprising of KOEL 125 KVA or equivalent, developing 159 BHP @ 1500 RPM, Liquid Cooled, electric start coupled to alternator as per IS 13364 mounted on a common base frame with standard control panel for automatic starting on main control panel having meters, sound proof canopy, integral fuel tank with battery and leads and accessories complete in all respect with emission control device to control the PM within range as prescribed by NGT/ norms published vde GSR 804(E) dt 03.11.2022 of GoI and updated till date on procurement and CPCB approved acoustic enclosure suitable for ambient condition at Wellington including required PCC foundation as per manufacturers instruction and confrrming to conditions under IS 10004722/1460 BS 5514/2613/ 5000 ISO 8526/3046 all as specified and as directed.

(A) Alternator :- Standard design alternator rated at 125KVA net output at site after considering derating as per site conditions at 0.8 (lag) power factor AC, 3 - phase 4 - wire 415 volts 50 Hz, 1500 RPM, self exicited self regulated screen protected drip proof IP 23 enclosure brushless design with widing in pole faces, insulating class 'H' and voltage regulation of ± 1 % at rated voltage from no load to full load. The alternator shall be confirming to BS 2613/5000 and shall be inposition to generate supply with frequency regulation with in ± 1% tolerance. The alternator will be suitable for tropical climate and shall generally confirm to BS - 2613/50001 IS - 4722 and as per the following provisions:- Make:- KIRLOSKAR/ JYOTI / STAMFORD/ CATERPILLAR/GREEVES

(i) Starter gear ring (ii) Start and stop push button (iii) Ignition key / Switch (iv) Handling and operation: Salient features of accessories shall be as under: (a) Radiator with blower fan (b) Corrosion inhibitor coolant (c) Paper element filters for fuel, lub oil and by pass. (d) Electronic governor controlled direct fuel injection system (e) Fly wheel housing and fly wheel.

(a) Fly wheel with housing (b) Cooling system :- Mounted radiator with fan & belts. (c) Cooling pump: - Centrifugal type belt driven. (d) Exhaust System :- Exhaust System complete with exhaust piping of suitable dia as per manufacture standard with MS pipe light grade up to and away two meters height from top of enclosure including necessary angle iron frame supports from floor to the bottom of exhaust pipe from the enclosure covered with mineral wool of thickness 50mm rapped with chicken wire mesh of size 2.25mm and aluminium sheet of 24 SWG to be complete with in the enclosure for safe exhaust without transforming vibration to the wall of the enclosure. Exhaust gas turbo charger type Exhaust manifold Silencer: Residential type Bellows

M&L for Point wiring complete with 1.5 sq mm single core PVC insulated FRLS unsheathed cable 1100 volts grade with multi stranded copper conductor confirming to IS-694 1990 wih ISI marked (for phase, neutral and earth) in and including stove enamelled Steel conduit with ISI Mark of minimum 20mm dia and all conduit accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets, fan regulators etc. of suiable size modules and the earth wire to be connected to common earth dolly complete all as specified and directed for One light point controlled by one modular switch 6A one way. Note: Location of light points, 6 Amp socket points and light fittings may be decided by Engr-in-charge as per site/user requirment.

fe handling and operation salient features of accessories shall be as under Make :- KIRLOSKAR/CUMMINS / CATERPILLAR (GEMCO)/ Greeves

(E) Generator Monitoring Panel: Comprising of following:- (a) Microprocessor based integrator generator set monitories, metering, protection and control system with built torque matched volts/H3 over load control. (b) Engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown)

(c) Alternator protection parameters like under voltage, over current, under frequency, over frequency ( alarm & shut down) (d) Relay drivers for remote annunciations (e) Cyclic cranking (f) Auto/manual start stop (g) Alternator trim adjustment from the front key pad (h) Operates within a temperature range 0- 50°C and humidity up to 95% (j) Remote monitoring capability through separate interface modules k) Genset metering parameters like lube oil pressure, coolant temperature, engine speed(rpm), run hours, DC voltage, 3 phase volts and 3 phase amperes, frequency, KW, KVA, power factor

(l) Safety Controls : - Engine low lube oil pressure, high water temperature and over speeding of engine. (m) Coupling arrangement : - Flexible coupling, fly wheel to suit flexible coupling fly wheel housing. (n) Accessories :-A VM Pads built or separately mounted to manufacturer base frames. (o) Base Frame: - Made out of ISMC 200 of sturdy design made of MS channel with necessary reinforcement and predetermined holes.

(p) Fuel Tank :- Daily service fuel tank of capacity minimum 08 hrs running storage (Inbuilt) made out of 3mm thick (Heat Retardant) sheet top and bottom with calibrated level indicating arrangement, stop cock, drain plug, fuel pump of suitable capacity and connected pipe line should be installed with in built inside the acoustic enclosure is inclusive of the cost of DG Set and is as per manufacturer design. (q) Deliverables:- Confirms the norms established by CPCB.

(F) AMF PANEL:- (a) Auto Main Failure (AMF) panel made out of 2 mm thick CRCA sheet, powder coated of conforming to IS 8623 totally enclosed dust and vermin proof with front and rear openings of 415 Volts, 3 Phase,4 Wire, AC 50 Hz having aluminium bus bar capacity required to carry current at 100% load of 58.50 KVA DG set with three phase and half neutral colour coded, prewired with copper flexible cable, be all as specified with the following accessories, control cable from Gen set to AMF panel:

(i) 200 Amps, 4 pole contactor - 2 Nos. (ii) MCCB, 4 Pole 63 Amps, 25 KA-2 Nos for both supplies suitable fuse links. (iv) CTs 50/5A for both the supplies. (v) DC Ammeter. (vi) DC Voltmeter. (vii) Push buttons. (viii) Indication Lamps. (ix) 2 over load+ earth leakage relay.

(x) Multi functional digital meter for KWH,KVA,KW,Amps,volts, frequency, power factor etc. (xi) SMPS Battery charger 12V, with trickle & Boost charging (xii) On/ Off switch. (xiii) Automatic/manual switch. (xiv) Hooter. (xv) Voltage sensing relay. (xvi) Six window enunciator for fault indications. (xvii) Electro magnetic relays. (xviii) Metering required in DG set :- A, V, Hz, KVA, KW, PF & KWH Metering required in mains :- A, V, Hz.

(G) Acoustic enclosure: CPCB approved enclosure is free standing floor mounted factory built and modular in construction to facilitate easy assembly at work site and will be drop over housing type. It will consist of acoustically treated panel housed in sheet steel will provide easy access for maintenance, repairs and operation. The enclosure is custom built to suit conditions, with the following features:- (a) Custom built product for various equipments, with ensure the optimum performance without duration.

(b) Rugged in construction maintenance free and modular designs which facilitate easy at site. (c) 16 SWG (1.6 mm) thick CRCA sheets to be used for enclosure panel to ensure longer life against weathering action. High quality acoustic insulation materials to be used as per IS 8183 for maximum sound absorption. Acoustic layers are supported by perforated sheets. (d) Sheet metal components of the enclosure should undergo various stages of surface treatment prior to painting which leads to be better life of the enclosure against weathering action. (e) Special paint treatment with pure polyester powder/epoxy to be provided for better weather resistance.

(f) Well designed ventilation system to be provided to pump up the heat in the chamber efficiently. (g) For effective acoustic / weather sealing a special type weather sealing gaskets, new frame rubber gaskets to be used. (h) Working space is to be provided around tube equipment for easy maintenance / repairs. (j) Necessary cut out provision for entry and exist of fuel lines cable to be incorporated in the enclosure as per the requirement. (k) A see through transparent window (glass or acrylic) in front of engine panel to be provided for monitoring the operation. (l) Ducting if required, bellows, mechanical hardware like locks, hinges fasteners etc to be provided. (m) Deliverables. 75 dBA @ imtr at 75% load under free field conditions. The temp inside tee enclosure will be within as per manufacturers recommendations above ambient temp.

(n) The enclosure should be provided with bulk head light fitting for inside illumination (o) The batteries should be placed inside the enclosure beside the DG Set on a suitable insulated platform. (p) The DG Set should be provided with external Emergency stop push button. (q) The acoustic enclosure parts shall be of powder coated after pre treatment process. (r) The powder coating shade should be Genset Green. The base frame should be painted with epoxy based black shade.

(f) Rate quoted shall be deemed to be included in making necessary holes to walls and making good the distrubed surfaces to match to original specification and connecting up all as specified and directed. (g) Civil Works :- All civil works with PCC plat form and related to foundations including of panel and equipments and making good the existing structrure of distrubed during installtion and commissioning of Genset. The depth of the foundation shall be minimum 300 mm with antivibration pads or as recommended by the manufacturer.

EFFICIENCY : (o) Overall efficiency (AC mode) - 95.5%. (p) Efficiency (Battery mode) - 94.5%. And ECO Mode :- 98.5% BATTERY & CHARGER : (q) Battery type/No/Make -VRLA/LEAD-ACID Type / Default 32 Nos, Adjustable 40 Nos/ Microtek. (r) Charging current - 12 A Maximum , Audjustable 1A to 12A, Factory Setting - 4A. BATTERY ENCLOSURE : Battery enclosure shall be MS Powder Coated. INDICATORS : (s) LCD Panel Display - UPS Status , Load percentage , Load Amps on each Phase, output VA & Output Wattage per phase,, Battery Level, Input/output voltage, Input/output frequency, Input line current per phase, Input VA & Input wattage per phase, temp information and data Log Events. Make/Model : Super Max + series Super performance high frequency Online UPS of make MICROTEK or techno-commercially equivalent of EMERSON/APC.

M & L earthing complete with copper earth plate electrode 60cm x 60cm x 3.15mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the copper earth strip of size 20 x 3mm, by means of nuts, bolts, check nuts and washer etc. of galvanised iron and earth lead protected by provision of GI pipe medium grade 40mm bore from earth electrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed. Note :- The cost of copper iron earth strip of 20 x 3mm size upto 7.5m long and protection pipe of 40mm bore GI light grade upto 7.5m long are deemed to be included in quoted unit rate.

Supplying, installing, testing and commissioning of Three Phase, Transformer based Online UPS system of capacity 30 KVA with in-built Isolation Transformer, indoor compact type complete with battery system & battery enclosure (Battery stand/ enclosure shall be MS Power Coated) suitable for minimum 30 Minutes back-up & comprising of the following features all as specified & as directed :

(a) DSP technology with IGBT based PFC & Inverter Section. (b) 3 Level IGBT Inverter design Maximizes Efficiency (c) Active power factor Correction in all 3 phases (d) 50 Hz/60Hz Frequency converter mode (e) ECO mode operation for Energy Saving (ECO) (f) Backfeed Energy Absorption Box (Optional), If Need to Operate Motor Type Loads on UPS (g) Generator Compatible (h) USB +RS-232 Mutiple communication available , SNMP (Optional) (j) 3-Stage extendable charging Design for optimized Battery Performance (k) Adjustable Battery Numbers (from 32 to 40 Batteries in Pairs of 2) (l) Built -in Maintenance Bypass & Static Bypass Switches (m) Parallel operation upto 3 units (optional) (with common Battery Bank) (n) Isolation Transformer (optional)

M & L earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth strip of size 32 x 6mm, by means of nuts, bolts, check nuts and washer etc. of galvanised iron and earth lead protected by provision of GI pipe light grade 40mm bore from earth electrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed. Note :- The cost of 7.5m long galvanised iron earth strip of 32 x 6mm size and protection pipe of 40mm bore GI light grade is deemed to be included in quoted unit rate.

(C) Fuel System :- Fuel injection system with fuel injectors, fuel injection solenoid switch/nozzles/ governor mechanical type capable for 1 % speed /frequency regulation. (i) Fuel filters (ii) Fuel hoses (iii) Lub oil System :- (iv)Lubricating oil filter (v) Lubricating oil pump (vi) Air Intake System :- (a) Air intake Manifold (b) Air cleaner dry type (a) Starting System :- Electric Self starter with maintenance free batteries including battery charging alternator. (b) Batteries:- 1 No. Maintenance free Battery of suitable AH capacity complete with copper conductor multistranded leads of suitable length from self starter to the battery terminals complete with initial charge and initial fill of electrolyte all as specified. Make:- EXIDE / AMRON / Produced by original DG set manufacturers

S&F 6-Way enclosure, IP-30 for independent mounting of MCB change-over switch (6M) fixed flush to wall/other surface complete all as specified and as directed. Cat No DBENC006SD of make L&T or techno-commercially equivalent of LEGRAND/SIEMENS

S&F MCB Double Pole, two way with centre-off changeover switch suitable for 400 V AC of rating 63 A complete. Cat No AUC00406300 of make L&T or techno-commercially equivalent of LEGRAND/SIEMENS